Jenn-Air JIM158XYCX0 Owner’s Manual

JENN_AIRTM

ICE MAKER

F_,BRCA

MACHIN

DE HIELO JENN-AIR '_

ENN-AIR _

USE & CARE GUIDE

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6242} or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6242} or visit our website at www.jennair.ca.

MANUAL DE USO Y CUIDADO

Para consultas respecto a caracteristicas, funcionamiento/desempe_o, piezas, accesorios o servicio en los EE.UU., Ilame al:

En CanadA, Ilame al: 1-800-JENNAIR (1-800-536-6247} o visite nuestra pagina de Internet: www.jennair.ca.

1-800-JENNAIR (1-800-536-6247} o visite nuestra pagina de Internet: www.jennair.com.

GUIDE D'UTILISATION ET D'ENTRETIEN

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247}

Table of Contents/[ndice/Table des matieres ...................................................................................... 2

ou visitez notre site Web www.jennair.ca.

JENN-AIR _

W10520236B

TABLE OF

ICE MAKER SAFETY ................................................................................... 3

INSTALLATION INSTRUCTIONS ............................................................... 4

Tools and Parts ......................................................................................... 4

Custom Panel Dimensions ....................................................................... 4

Unpack the Ice Maker ............................................................................... 5

Location Requirements ............................................................................. 5

Electrical Requirements ............................................................................ 6

Water Supply Requirements ..................................................................... 6

Vacation or Extended Time Without Use ................................................. 6

Connect Water Supply .............................................................................. 6

Ice Maker Drain Pump Installation ............................................................ 7

Drain Connection .................................................................................... 10

Install Custom Overlay Panel .................................................................. 11

Ice Maker Door Reversal--Side Swing Only .......................................... 12

Leveling ................................................................................................... 13

Water Filtration System .......................................................................... 14

[NDICE

CONTENTS

ICE MAKER USE ....................................................................................... 15

How Your Ice Maker Works ................................................................... 15

Using the Controls .................................................................................. 15

Normal Sounds ....................................................................................... 16

ICE MAKER CARE ..................................................................................... 16

Cleaning .................................................................................................. 16

Vacation and Moving Care ..................................................................... 18

TROUBLESHOOTING ............................................................................... 19

Ice Maker Operation ............................................................................... 19

Ice Production ......................................................................................... 20

Ice Quality ............................................................................................... 20

Plumbing Problems ................................................................................ 21

ASSISTANCE OR SERVICE ...................................................................... 21

In the U.S.A............................................................................................. 21

In Canada ................................................................................................ 21

Accessories ............................................................................................. 22

PERFORMANCE DATA SHEET ................................................................ 22

WARRANTY ............................................................................................... 23

SEGURIDAD DE LA FABRICA DE HIELO ............................................... 25

INSTRUCCIONES DE INSTALACION ...................................................... 26

Herramientas y piezas ............................................................................ 26

Dimensiones del panel hecho a la medida ............................................. 26

Desempaque la fabrica de hielo ............................................................. 27

Requisitos de ubicaci6n ......................................................................... 27

Requisitos electricos ............................................................................... 28

Requisitos del suministro de agua ......................................................... 28

Vacaciones o tiempo prolongado sin uso .............................................. 29

Conexi6n del suministro de agua ........................................................... 29

Instalaci6n de la bomba de desagQe de la fabrica de hielo .................. 30

Conexi6n del desagQe ............................................................................ 33

Instalaci6n el panel de revestimiento hecho a la medida ...................... 34

Cambio del sentido de apertura de la puerta de la fabrica de hielo:

apertura lateral solamente ...................................................................... 34

Nivelaci6n ................................................................................................ 36

Sistema de filtraci6n de agua ................................................................. 37

TABLE DES MATIERES

SECURITE DE LA MACHINE .,_GLAQONS ............................................. 49

INSTRUCTIONS D'INSTALLATION ......................................................... 49

Outillage et pieces .................................................................................. 49

Dimensions du panneau personnalise ................................................... 50

Deballage de la machine a glagons ........................................................ 51

Exigences d'emplacement ..................................................................... 51

Specifications _lectriques ....................................................................... 52

Specifications de I'alimentation en eau .................................................. 52

Vacances ou Iongue p6riode d'inutilisation ............................................ 52

Raccordement a la canalisation d'eau ................................................... 52

Installation de la pompe de vidange de la machine a glagons .............. 53

Raccordement au drain de vidange ....................................................... 56

Installation du panneau decoratif personnalise ...................................... 57

Inversion du sens d'installation de la porte de la machine a glagons--

Porte a ouverture lat6rale uniquement ................................................... 58

Nivellement ............................................................................................. 60

Syst_me de filtration d'eau ..................................................................... 60

USO DE LA FABRICA DE HIELO ............................................................. 38

C6mo funciona su fabrica de hielo ........................................................ 38

Uso de los controles ............................................................................... 38

Sonidos normales ................................................................................... 39

CUll)ADO DE LA FABRIOA DE HIELO .................................................... 39

Limpieza .................................................................................................. 39

Cuidado durante las vacaciones y mudanzas ....................................... 42

SOLUCION DE PROBLEMAS ................................................................... 43

Funcionamiento de la fabrica de hielo ................................................... 43

Producci6n de hielo ................................................................................ 44

Calidad del hielo ..................................................................................... 44

Problemas de plomeria .......................................................................... 45

AYUl)A O SERVlCIO TleCNICO ................................................................ 45

En los EE.UU ........................................................................................... 45

Accesorios .............................................................................................. 45

HOJA DE I)ATOS l)EL RENI)IMIENTO ................................................... 46

GARANTJA ................................................................................................. 47

UTILISATION DE LA MACHINE .,_GLAQONS ........................................ 61

Fonctionnement de la machine &gla(_ons ............................................. 61

Utilisation des commandes .................................................................... 62

Bruits normaux ....................................................................................... 62

ENTRETIEN DE LA MACHINE A GLAQONS ........................................... 63

Nettoyage ............................................................................................... 63

Precautions & prendre avant les vacances ou un demenagement ....... 65

I)IePAN NAGE ............................................................................................. 66

Fonctionnement de la machine &gla(_ons ............................................. 66

Production de gla(_ons ........................................................................... 67

Qualit6 des gla(_ons ................................................................................ 68

Problemes de plomberie ........................................................................ 68

ASSISTANCE OU SERVICE ...................................................................... 69

Aux I_tats-Unis ........................................................................................ 69

Au Canada .............................................................................................. 69

Accessoires ............................................................................................. 69

FEUlLLE DE I)ONNleES SUR LA PERFORMANCE ................................ 70

GARANTIE .................................................................................................. 71

ICE MAKER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

Plug into a grounded 3 prong outlet. • Disconnect power before manually cleaning the inside components. Do not remove ground prong. • Disconnect power before servicing.

Do not use an adapter. • Replace all parts and panels before operating. Do not use an extension cord. • Use two or more people to move and install ice maker.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

INSTALLATION INSTRUCTIONS

Tools Needed Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Cordless drill • Masking tape

• Phillips screwdriver • Tape measure

• Router or planer • Towel or piece of cardboard

• Pencil

Parts Needed

Custom Overlay Door Panel--See "Custom Panel Dimensions," #8 x 1/2"pan-head wood screws (8)

Parts Supplied

• Adhesive pads (4)

If you plan to install a custom overlay panel, you will need to make the panel yourself or consult a qualified cabinetmaker or carpenter.

IM PORTANT:

• The thickness of the overlay panel must be 3/4"(1.91 cm).

• Overlay panel must not weigh more than 8 Ibs (3.62 kg).

• Overlay panels weighing more than recommended may cause damage to your ice maker.

• Match wood grain direction with that of adjacent cabinets.

• Sand panel edges to provide a smooth finish.

• Use moisture sealer on both sides and all edges of the panel to avoid damage from moisture.

lY4" 1V4"

(3.18cm) (3.18 cm)

3/4"

1/411

(6.35 mm)

(1.91 cm)

1/4"

(6.35 mm)

Option 2--With Hinge-Side Spacer

To achieve a flush installation with adjacent cabinets, prepare the custom overlay panel using the dimensions shown.

Front of Panel

---;_-

(0.95 cm)

29V2"

(74.9 crn)

Option 1--Without Hinge-Side Spacer

To allow proper clearance for the door, prepare the custom overlay panel using the dimensions shown.

29V2"

(74.9 cm)

I'_ 1417/32" _'1

(36.9 cm)

Top of Panel

A. Front--visible surface when installed B. Hinge side

C. Notch to a depth of _" (0.95 cm)

Bottom of Panel

A.Front--visible surface when installed

B.Hinge side

C. Notch to adepth of _" (0.95 cm)

(0.95 cm)

14%"

(37.1 cm)

11,/4"

(3.16 cm)

t .I'/,"

A B C

/._L,, (1.27 cm)

B C

1V4"

(3.16 cm)

(1.27 cm)

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

• To remove any remaining tape or glue from the exterior of the ice maker, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small

amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

• Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. Do not

use chlorine bleach on the stainless steel surfaces of the ice maker. These products can damage the surface of your

ice maker.

Option 1--Without Hinge-Side Spacers

34"

(86.4 cm)

Min.

341/2''

(87.6 cm)

Max.

281/2"

(72.4 cm)

Cleaning Before Use

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in

the "Ice Maker Care" section.

• To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The ice maker may be

closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

• Installation of the ice maker requires a cold water supply inlet of 1/4"(6.35 mm) OD soft copper tubing with a shutoff valve or

a Whirlpool supply line Part Number 8212547RB, and a Whirlpool approved drain pump, Part Number 1901A, only to carry the water to an existing drain.

• Choose a well ventilated area with temperatures above 55°F (13°C) and below 110°F (43°C). Best results are obtained between 70°F and 90°F (21°C and 32°C).

• The ice maker must be installed in an area sheltered from the elements, such as wind, rain, water spray, or drip.

• Choose a location where the floor is even. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the

height of the leveling legs. See "Leveling."

• When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as

shown.

NOTES:

• Check that the power supply cord is not damaged, or

pinched or kinked between the ice maker and the cabinet.

• Check that the water supply line is not damaged, or

pinched or kinked between the ice maker and the cabinet.

• Check that the drain line (on some models) is not

damaged, or pinched or kinked between the ice maker and the cabinet.

A.Recommended location forelectrical and plumbing fixtures B.Floor level

Option 2--With Hinge-Side Spacers

34"

(86.4 cm)

Min.

341/2"

(87.6 cm)

Max.

cm)

15%"

0.0 cm)

A. Recommended location for electrical and plumbing fixtures B. Hinge-side, back spacer (Install 6" [15.24 cm] from back wall to aid in

drain afignment)

C. Hinge-side front spacer (Install flush with front face of adjacent cabinet)

-_ F3/_ '' (1.9 cm)

281/2"

(72.4 cm)

_I-_ ...... _d_,,,¸_ I _..... ,i _@_-@ ;_

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to folow these instructions can result in death,

fire, or electrical shock.

Before you move your ice maker into its final location, it is important to make sure you have the proper electrical

connection: A 115 volt, 60 Hz., AC only, 15- or 20-amp electrical supply,

properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required.

It is recommended that aseparate circuit, serving only your ice maker, be provided. Use a receptacle which cannot be turned off

by a switch or pull chain. IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) equipped outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Ice quality

may be affected. If nuisance tripping has occurred, and if the condition of the ice appears poor, dispose of it.

Recommended Grounding Method

The ice maker must be grounded. The ice maker is equipped with a power supply cord having a 3 prong grounding plug. The cord

must be plugged into a mating, 3 prong, grounding-type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility of the customer to

have a properly grounded, 3 prong wall receptacle installed by a qualified electrician.

Check that the water supply lines are insulated against freezing conditions. Ice formations in the supply lines can increase water pressure and damage your ice maker or home. Damage from

frozen supply lines is not covered by the warranty. A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the ice maker. If you have questions about your water pressure, call a licensed,

qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT:

• A reverse osmosis water filtration system is not recommended for ice makers that have a drain pump

installed.

• For gravity drain systems only.

• The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the ice

maker needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa). NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of

water per hour to the ice maker for proper ice maker operation. If a reverse osmosis system is desired, only a whole-house

capacity reverse osmosis system, capable of maintaining the steady water supply required by the ice maker, is recommended. Faucet capacity reverse osmosis systems are not able to maintain the steady water supply required by the ice maker.

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

When you will not be using the ice maker for an extended period of time, turn off the water and power supply to the ice

maker. Check that the water supply lines are insulated against

freezing conditions. Ice formations in the supply lines can increase water pressure and cause damage to your ice maker

or home. Damage from freezing is not covered by the warranty.

Read all directions before you begin. IM PC RTANI"."

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and

ordinances.

• Use copper tubing or Whirlpool supply line, Part Number 8212547RP, and check for leaks.

• Install tubing only in areas where temperatures will remain above freezing.

Tools Needed Gather the required tools and parts before starting installation:

• Flat-blade screwdriver

• 7/le"and W' open-end wrenches or two adjustable wrenches

• _/4"nut driver

NOTE: Do not use a piercing-type or 3/_e"(4.76 mm) saddle valve which reduces water flow and clogs more easily.

Connecting the Water Line

Turn off main water supply. Turn on nearest faucet long enough to clear line of water.

Using a 1/2"copper supply line with a quarter-turn shutoff valve or the equivalent, connect the ice maker as shown.

NOTE: To allow sufficient water flow to the ice maker a minimum 1/2"diameter home supply line is recommended.

Rear View

I/ II

A. Bulb

B. Nut

Now you are ready to connect the copper tubing. Use 1/4"

(6.35 mm) OD soft copper tubing for the cold water supply.

• Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut

square.

• Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A. Copper tubing B. Water supply tube clamp

Remove and discard the short, black plastic tube from the

C. Inlet water tube clamp and

supply line connector

end of the water line inlet.

Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet's side wall or other parts inside the cabinet.

A B C D

A. Line to ice maker B. Nut (purchased)

C. Ferrule (purchased) D. Supplied line from ice maker

8. Install the water supply tube clamp around the water supply line to reduce strain on the coupling.

9. Turn shutoff valve ON.

10. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

A. Compression sleeve

B. Compression nut

C. Copper tubing

4. Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is

clear. Turn off shutoff valve on the water pipe. IMPORTANT: Always drain the water line before making the

final connection to the inlet of the water valve to avoid possible water valve malfunction.

5. Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown.

Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

NOTE: Connect drain pump to your drain in accordance with all state and local codes and ordinances. It may be desirable to insulate drain tube thoroughly up to drain inlet to minimize

condensation on the drain tube. Insulated tube kit Part Number W10365792 is available for purchase. Drain pump is designed to

pump water to a maximum height of 10 ft (3 m). Use only Whirlpool approved drain pump kit Part Number 1901A.

Kit Contains:

• Drain pump kit Part Number 1901A

• %" ID x 51/8'' drain tube (ice maker bin to drain pump reservoir inlet)

• 1/2"IDx10ft(3m)draintubehose(drainpumpdischargeto householddrain)

• %e"IDx32"(81cm)venttube(drainpumpreservoirventto icemakercabinetback)

• Cableclamps(securesventtubetobackoficemaker)(3)

• #8-32x3/8"pumpmountingscrews(securesdrainpumpto baseplateandclampstobackoficemaker)(5)

• 8/8"smalladjustablehoseclamp(securesventtodrainpump)

• 7/8"largeadjustablehoseclamp,(securesdraintubetoice makerbinanddrainpumpreservoirinlet)(3)

• Rearpanel(2)

• Instructionsheet

If Ice Maker Is Currently Installed

Water Supply Line

z_JJ

NOTE: If ice maker is not installed, please proceed to "Drain Pump Installation" section.

1. Push the selector switch to the Off position.

Electrical Shock Hazard

Disconnect power before servicing. Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

2. Unplug ice maker or disconnect power.

3. Turn off water supply. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove all ice from bin.

4. Unscrew the drain cap from the bottom of the water pan located inside the storage bin. Allow water to drain

completely. Replace drain cap. See "Drain Cap" illustration.

Drain Cap

A. _" copper tubing

B. Cable clamp

C. _" compression nut

D. Ferrule (sleeve) E. Ice maker connection

Drain Pump Installation

NOTE: Do not kink, smash or damage tubes or wires during installation.

Unplug ice maker or disconnect power.

Remove rear panel. See "Rear Panel" illustration for 5 screw locations. Pull rear panel away from the drain tube and

discard.

Rear Panel

m m

A. Drain cap

5. If ice maker is built into cabinets, pull ice maker out of the opening.

6. Disconnect water supply line. See "Water Supply Line" illustration.

A. Screw locations

Remove the old drain tube and clamp attached to the ice maker bin.

NOTE: Discard old drain tube and clamp.

Install new drain tube (8/8"ID x 51/8'') from ice maker bin to drain pump reservoir inlet using new adjustable clamps. See "Drain Tube" illustration.

NOTES:

• Do not kink.

• Trim tube length, if required.

Drain Tube

A. _" adjustable hose clamp C. ½" adjustable hose clamp B. Drain tube (ice bin to drain pump) D. Drain pump reservoir inlet

Install vent tube (S/le"ID x 32" [81 cm]) to drain pump reservoir vent. Use one 8/8"small adjustable clamp, supplied. See

"Parts Locations" illustration. NOTE: Do not install household drain tube at this time.

Parts Locations

Drain Pump Mounting Tab Slot

A. Mounting tab slot

Drain Pump Installed

G F

A. Vent tube B. _" hose clamp

C. Drain pump discharge tube

D. Drain pump

Remove power cord clamp and ground screw attached to ice maker power cord, which is mounted to the unit base. See

"Parts Locations" illustration. NOTE: Clamp and screw will be reused.

Slide drain pump into the ice maker base on the right side. The pump mounting tab should slip into the rectangular slot

in the ice maker base. It will be necessary to tip the pump slightly to slip into the slot. See "Drain Pump Mounting Tab

Slot" illustration.

E.Ice maker unit power cord F. #8-32 x _" pump mounting screws

G. Drain pump power cord, clamp

and screw

A. Drain pump installed

Align the 2 screw holes at the rear of the pump. Use two #8-32 x 3/8"screws, supplied. See "Parts Locations"

illustration.

Connect drain tube to ice maker bin outlet (8/8"ID), using 7/8" adjustable clamp, supplied. See "Drain Tube" illustration.

10.

Coil ice maker power cord into a 4" (10.2 cm) diameter coil. Wrap electrical tape around the power cord in several places

to keep the cord in a coil. Locate coiled power cord between the drain pump and side of enclosure and plug into the receptacle of the drain pump. See "Parts Locations"

illustration.

11.

Attach the drain pump power cord to ice maker unit base with clamp and screw (removed in Step 6) that was used to attach ice maker power cord. See "Parts Locations" illustration.

12.

Place new rear panel (small one for 15" ice makers, large one for 18") against the back of the ice maker. Route the vent

tube and drain pump discharge tube through cutouts in the rear panel.

13.

Secure rear panel with original screws. See "Rear Panel" illustration.

14.

Secure vent tube to back of ice maker using 3 clamps and three #8-32 x 3/8"screws, supplied. See "Vent Tube"

illustration.

Vent Tube NOTE: Do not pinch, kink or damage the vent tube. Check that it

is not damaged, or pinched or kinked between the cabinet and the ice maker.

Gravity Drain System

A .............. _ ..........

A. Vent tube B. Clamps and screws

15. Attach 1/2"ID x 10 ft (3 m) drain tube to pump discharge tube. See "Parts Locations" illustration.

16. Connect ice maker to water supply and install ice maker as specified by the product installation instructions.

17. Check all connections for leaks.

Connect the ice maker drain to your drain in accordance with all state and local codes and ordinances. If the ice maker is

provided with a gravity drain system, follow these guidelines when installing drain lines. This will help keep water from flowing

back into the ice maker storage bin and potentially flowing onto the floor causing water damage.

• Drain lines must have a minimum of 5/8"(15.88 mm) inside diameter.

• Drain lines must have a 1" drop per 48" (2.54 cm drop per 122 cm) of run or 1/4"drop per 12" (6.35 mm per 30.48 cm) of

run and must not have low points where water can settle.

• The floor drains must be large enough to accommodate drainage from all drains.

• The ideal installation has a standpipe with a 1W' (3.81 cm) to 2" (5.08 cm) PVC drain reducer installed directly below the

outlet of the drain tube as shown. You must maintain a 1" (2.54 cm) air gap between the drain hose and the

standpipe.

IMPORTANT: A drain pump is necessary when a floor drain is not available. A Drain Pump kit, Part Number 1901A, is available for purchase.

Side View

(4.8 cm)

1" (2.54 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

18. Plug in ice maker or reconnect power.

19. Turn on ice maker.

20. Wait for rinsing cycle, approximately 5 minutes, to be sure the ice maker is operating properly.

A. Drain hose B. 1" (2.54 cm) air gap

C. PVC drain reducer

23" C

(58.4cm)

2". 11/d'

(5 cm - 3.8 cm)

D. Center of drain should be 23" (58.4 cm) from

front of door, with or without the _" (1.91 cm) panel on the door. The drain should also be

centered from left to right (7_" [18.56 cm[ from either side of the ice maker) unless

installing with a spacer.

Drain Pump System (on some models)

Connect the ice maker drain to your drain in accordance with the International Plumbing Code and any local codes and

ordinances. NOTE: If the drain hose becomes twisted and water cannot

drain, your ice maker will not work.

Connecting the Drain

After ensuring that the drain system is adequate, follow these steps to properly place the ice maker:

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

6. Install the door handle on the panel.

7. Remove the tape from the face of the door.

8. Remove the paper backing from the adhesive pads that are located on the door front.

9. Place the panel on the door, align with markings and apply pressure in the area of the adhesive pads.

10. Make sure the ice maker door opens and closes easily.

11. Pull the ice maker forward to access the top and sides of the door.

12. Remove the gaskets from the interior door panel and set aside.

13. Using the factory drilled holes as a guide, use a pencil and mark the drilling locations on the overlay panel.

14. Drill eight Vs"x W' (3.18 mm x 12.7 mm) deep holes into the overlay panel.

NOTE: Do not drill deeper than W' (12.7 mm).

15. Use eight #8 x W' pan-head wood screws to attach the panel to the door.

16. Replace the gaskets on the inner door panel.

17. Move the ice maker back into place under the counter.

Option 1--Without Hinge-Side Spacer

291/2"

(74.9 cm)

Excessive Weight Hazard Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

2. Style 1--For gravity drain system, push the ice maker into position so that the ice maker drain tube is positioned over the PVC drain reducer. See "Gravity Drain System."

Style 2--For drain pump system connect the drain pump outlet hose to the drain. See "Drain Pump System."

3. Recheck the ice maker to be sure that it is level. See "Leveling."

4. If it is required by your local sanitation code, seal the cabinet to the floor with an approved caulking compound after all

water and electrical connections have been made.

IMPORTANT: Create custom overlay panel according to the specifications in the "Custom Panel Dimensions" section.

1. Install the ice maker.

2. Level the ice maker. See "Leveling."

3. Place the ice maker under the cabinet so that the front edge of the custom panel will align with the front edge of the surrounding cabinets.

4. Hold the custom panel up to the ice maker and check that the opening and alignment are correct. Mark location of the panel

as necessary.

5. Mark location of the handle. Remove the panel from the door, and then drill holes for the handle.

A. #8 x ½" pan-head

wood screw

B. Adhesive pads C. Custom panel

Option 2--With Hinge-Side Spacer

291/2"

(74.9 cm)

(37.1 cm)'-_

A. #8 x ½" pan-head

wood screw

B.Adhesive pads C. Custom panel

Tools Needed 2.

Gather the required tools and parts before starting installation. 3.

• %e" wrench • Flat putty knife 4.

• _/4"wrench • Phillips screwdriver

Hinge pin

5_6" hex-head hinge screw

Remove the handle screws and handle (on some models). Remove the hinge pin from the top hinge. Remove the door from the hinges and replace the top hinge

pin.

Remove the screw and door stop at corner A. Remove the screw and end cap at corner 0. Place the door stop at corner C, and tighten screw. Place the end cap at corner A, and

tighten screw.

Remove the screw and door stop at corner D. Remove the screw and end cap at corner B. Place the door stop at corner B, and tighten screw. Place the end cap at corner D, and

tighten screw.

Handle screw End cap screw

Remove Stainless Steel Door Wrap Panel-- On Some Models

A.Hex-head screws

1. Remove the 2 hex-head screws located under the stainless steel door wrap panel flange on the bottom of the door.

2. Pull up and outward on the door wrap panel from the bottom.

3. Rotate the door wrap panel until it separates from the door and pull up.

NOTE: Be sure the edge guards do not separate from the door wrap panel.

Door Stop and End-Cap Reversal

A B

D C

A. Top corner open (no end cap) C. Beginning bottom corner end cap

B. Beginning top corner end cap D. Bottom corner open (no end cap)

7. Depending on your model, the brand badge for the front door of your ice maker may be in the package with the Use and Care Guide. Fasten the brand badge to the door.

8. Set the door aside.

Reverse Hinges

1. Unscrew and remove the top hinge. Replace the screws in the empty hinge holes.

2. Remove the screws from the bottom of the opposite side of the ice maker cabinet. Turn the top hinge upside down so

that the hinge pin points up. Place the hinge on the bottom opposite side of the ice maker and tighten screws.

3. Remove the "old" bottom hinge screws and hinge. Replace the screws in the empty hinge holes.

4. Remove the screws from the top of the opposite side of the ice maker cabinet. Turn the hinge upside down so that the hinge pin points down. Place the hinge on the top opposite side of the ice maker and tighten the screws.

5. Remove the top hinge pin.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

1. Unplug the ice maker or disconnect power.

Replace Door

1. Place the door on the bottom hinge pin.

2. Align the door with the top hinge hole and replace the top hinge pin.

3. Replace the handle and handle screws.

Replace Door Wrap--On Some Models

1. Place the door wrap flange onto the door top and ensure that it fits correctly.

2. Rotate the door wrap downward until it covers the door surface completely.

3. Install the 2 hex-head screws into the bottom of the door.

Top Hinge 3. Install the white decorative screws on the opposite side of the

door.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

A. Hinge pin

B. Phillips-head countersink screw

C. Hinge pin sleeve

D. Hinge

E. Hex-head hinge screw

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Bottom Hinge

4. Plug into a grounded 3 prong outlet.

It is important for the ice maker to be level in order to work properly. Depending upon where you install the ice maker, you

may need to make several adjustments to level it. You may also use the leveling legs to lower the height of the ice maker for

undercounter installations.

C D

A. Hex-head hinge screw

B. Hinge pin sleeve

C. Phillips-head countersink screw

D. Hinge pin E. Hinge

Reverse Door Catch

1. Remove the white decorative screws from the opposite side of the door and set aside.

2. Remove the screws from the magnetic door catch and replace it on the opposite side of the door.

Tools Needed

Gather the required tools and parts before starting installation.

• 9" level

• Adjustable wrench NOTE: It is easier to adjust the leveling legs if you have another

person to assist you.

1. Move the ice maker to its final location. NOTE: If this is a built-in installation, move the ice maker as

close as possible to the final location.

Place the level on top of the product to see whether the ice maker is level from front to back and side to side.

3. Push up on the top front of the ice maker, and then locate the leveling screws that are on the bottom front of the ice maker.

4. Using an adjustable wrench, change the height of the legs as follows:

• Turn the leveling leg to the right to lower that side of the

ice maker.

• Turn the leveling leg to the left to raise that side of the ice

maker.

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

5. Push up on the top rear of the ice maker and locate the leveling legs that are on the bottom rear of the ice maker.

6. Follow the instructions in Step 4 to change the height of the legs.

7. Use the level to recheck the ice maker to see that it is even from front to back and side to side. If the ice maker is not

level, repeat steps 2 to 5. If the ice maker is level, go to the "Connect Water Supply" section.

Do not use with water that is microbiologbally unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Install the Water Filter

1. Locate the accessory packet in the ice maker and remove the water filter.

2. Take the water filter out of its packaging and remove the cover from the O-rings. Be sure the O-rings are still in place

after the cover is removed.

4. Attach the filter wrench to the water filter.

Align the alignment pin on the side of the filter with the cutout notch in the control housing and insert the filter into the

housing.

A. Cover C. Alignment pin

B. O-rings D. Alignment arrow

The water filter compartment is located in the right-hand side of the ice maker control panel. Push in on the door to release the latch, and then lower the door.

A. Door

A. Alignment pin B. Unlocked symbol

Turn the filter clockwise until it locks into the housing. Ensure that the alignment arrow on the filter head aligns with the

locked symbol on the control box housing. NOTE: If the filter is not correctly locked into the housing, the

ice maker will not produce ice.

C.Locked symbol

D. Cutout notch incontrol housing

A. Alignment arrow aligned with locked symbol

7. Remove the filter wrench.

8. Push the control box door closed until the latch snaps closed.

The Water Filter Status Light

The water filter status lights will help you know when to change your water filter.

• The "Order Filter" status light will be illuminated when it is time to order a replacement filter.

• The "Replace Filter" status light will be illuminated when it is time to replace the filter.

• Replacing the disposable water filter with a new filter will automatically reset the filter status tracking feature. See "Using the Controls."

NOTES:

• "Replace Filter" will remain illuminated if a filter is not

installed.

• The "Filter" status light will flash if the filter is not correctly

installed or there is an obstruction in the water line.

Replace the Water Filter

To purchase a replacement water filter, see "Accessories." Replace the disposable water filter when indicated on the water

filter status display or at least every 9 months. If the ice making rate decreases before the Replace Filter light illuminates, then replace the filter.

1. Locate the water filter compartment in the right-hand side of the control housing. See Step 3 in the "Install Water Filter"

section.

ICE MAKER USE

When you first start your ice maker, the water pan will fill and the system will rinse itself before starting to make ice. The rinsing process takes about 5 minutes.

Under normal operating conditions, the ice maker will cycle at preset temperatures. The ice level sensor located in the ice

storage bin will monitor the ice levels. IMPORTANT: If the water supply to the ice maker is turned off,

be sure to set the ice maker control to OFR

The Ice Making Process

1. Water is constantly circulated over a freezing plate. As the water freezes into ice, the minerals in the water are rejected. This produces a sheet of ice with a low mineral content.

2. Turn the water filter counterclockwise (to the left), and pull it straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling may occur.

3. Install the replacement water filter by following steps 2 through 6 in the "Install the Water Filter" section.

NOTE: As the room and water temperatures vary, so will the amount of ice produced and stored. This means that higher operating temperatures result in reduced ice production.

1. To start ice production, press ON/OFF.

2. To stop ice maker operation, press ON/OFF.

2. When the desired thickness is reached, the ice sheet is released and slides onto a cutter grid. The grid divides the

sheet into individual cubes.

3. The water containing the rejected minerals is drained after each freezing cycle.

4. Fresh water enters the machine for the next ice making cycle.

5. Cubes fall into the storage bin. When the bin is full, the ice maker shuts off automatically and restarts when more ice is

needed. The ice bin is not refrigerated, and some melting will occur. The amount of melting varies with room temperature.

NOTES:

• Pressing the On/Off button does not shut off power to the ice maker.

• Allow 24 hours to produce the first batch of ice. Discard the first 2 batches produced.

Max Ice Mode

Select the Max Ice feature when you have an upcoming need for a large amount of ice and the ice bin is low or empty. Max Ice

mode will produce a greater quantity of ice in a 24-hour period.

• Press MAX ICE while the ice maker is on. The indicator light will illuminate.

• Press MAX ICE again to turn off the Max Ice feature. The indicator light will turn off.

• The Max Ice mode will be on when you first turn on the product. It will turn off after 24 hours. To turn Max Ice back on, press MAX ICE.

Clean

Door Ajar Alarm

It is recommended that you clean the ice maker when the "Cleaning Needed" light is illuminated or 9 months has elapsed

or ice production decreases significantly. To clean your ice maker, see "Ice Maker System" in the "Cleaning" section.

No sa/So s sds

Your new ice maker may make sounds that are not familiar to you. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces such as floors, walls and cabinets can make the sounds seem louder than they actually are. The following describes the

kinds of sounds that might be new to you and what may be making them.

• You will hear a buzzing sound when the water valve opens to fill the water pan for each cycle.

• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the ice maker can also make noises.

• The high-efficiency compressor may make a pulsating or high pitched sound.

• Water running over the evaporator plate may make a splashing sound.

ICE MAKER CARE

The Door Ajar Alarm feature sounds an alarm when the ice maker door is open for 5 minutes. The alarm will repeat every 2 minutes.

Close the door to turn off. The feature then resets and will reactivate when the door is left open again for 5 minutes.

Water running from the evaporator plate to the water pan may make a splashing sound.

As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your ice maker.

You may hear air being forced over the condenser by the condenser fan.

During the harvest cycle, you may hear a "thud" when the ice sheet slides from the evaporator onto the cutter grid.

When you first start the ice maker, you may hear water running continuously. The ice maker is programmed to run a rinse cycle before it begins to make ice.

If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud sound during water filling associated with the flow of water through the inlet

valve. Call a licensed, qualified plumber to determine the best method to reduce the supply water pressure (50 psi is recommended).

The ice making system and the air cooled condenser need to be cleaned regularly for the ice maker to operate at peak efficiency and to avoid premature failure of system components. See the

"Ice Maker System" and the "Condenser" sections.

Exterior Surfaces

Wash the exterior enamel surfaces and gaskets with warm water and mild soap or detergent. Wipe and dry. Regular use of a good household appliance cleaner and wax will help maintain the

finish. Do not use abrasive cleaners on enamel surfaces as they may scratch the finish.

For products with a stainless steel exterior, use a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Do not use chlorine bleach on the stainless steel surfaces.

Ice Maker System

Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system.

Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is. With hard water of 15 to 20 grains/gal. (4 to 5 grains/liter), you may need to clean the system as often as

every 9 months. NOTE: Use one 16 oz (473 mL) bottle of approved ice maker

cleaner. To order, see "Accessories."

1. Press the ON/OFF button.

2. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove all ice from the storage bin.

3. Unscrew the drain cap from the bottom of the water pan located inside the storage bin as shown. Allow the water to

drain completely.

4. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan and you will

have either thin ice or no ice.

5. Read and follow all handling information on the cleaner bottle before completing the steps below. Use one 16 oz (473 mL) bottle of approved ice maker cleaner.

6. Pour one bottle of solution into the water pan. Fill the bottle twice with tap water and pour it into the water pan.

A. Water pan B. Drain cap

Press the CLEAN button. See "Using the Controls." The Clean button will blink, indicating that the cleaning cycle is in process. When the "Cleaning Complete" light is illuminated

(approximately 70 minutes), the cleaning cycle is complete. During the cleaning cycle, the system will both clean and

rinse itself.

After the cleaning cycle is complete, remove the drain cap from the water pan. Look for any cleaning solution left in the

water pan. If cleaning solution drains from the water pan, you should run the clean cycle again. Be sure to refill the water pan with cleaner before starting the clean cycle again. Be sure to replace the drain cap securely on the water pan. If the

drain cap is loose, water will empty from the water pan and you will have either thin ice or no ice.

NOTE: Severe scale buildup may require repeated cleaning with a fresh quantity of cleaning solution.

9. Press the ON/OFF button to resume ice production.

Condenser

A Dirty or Clogged Condenser

• Obstructs proper airflow.

• Reduces ice making capacity.

• Causes higher than recommended operating temperatures which may lead to component failure.

Electrical Shock Hazard

Disconnect power before cleaning.

Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

Pull out on the bottom of the cutter grid cover until the snaps release to remove.

Unplug the wiring harness from the left side of the cutter grid.

A. Cutter grid cover

6. Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

7. Remove the right-hand and left-hand screws. Lift the cutter grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

1. Unplug ice maker or disconnect power.

2. Remove the 2 screws in the lower access panel and the 2 screws from the base grille area of the front panel support.

3. Pull the bottom forward and then pull down to remove the lower access panel.

4. Remove dirt and lint from the condenser fins and the unit

compartment with a brush attachment on a vacuum cleaner.

A. Condenser fins

5. Replace the lower access panel using the 4 screws.

6. Plug in ice maker or reconnect power.

Interior Components

1. Unplug ice maker or disconnect power.

2. Open the storage bin door and remove any ice that is inthe bin.

Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap securely on the water pan.

If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

AB:i_ii:y:_.,,._,_.......... ;..........................DE

A. Cutter grid harness B. Screw

C. Cutter grid

D. Ice level sensor harness

E. Plastic spacer F. Screw

8. Remove the mounting screw that holds the water pan in place. Pull out on the front of the water pan.

9. Disconnect the pump bracket from the water pan and unplug the water pan drain pump.

f __ E

A, Waterpan C.Drain cap B. Waterpan screw D.Drain pump cover

10. Remove, clean and replace the ice scoop and ice scoop holder.

NOTE: On some models, the ice scoop holder is located in the upper left of the unit, and on other models, the ice scoop

holder is located in the lower left of the unit.

• After removing the ice scoop, remove the holder by

removing the 2 screws.

• Wash the ice scoop holder along with the other interior

components using the following instructions.

• Replace the ice scoop holder by replacing the screws.

A. Screws B. Ice scoop holder

11. Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm

water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

................ @_W_ .........._

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

To Shut Down the Ice Maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from storage bin.

3. Shut off the water supply.

4. Remove the 2 screws in the lower access panel and the 2 screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above

145°F (63°C).

12. To replace the water pan, set the water pan inside the ice bin. Hook up the water pan pump. Snap the pump bracket back onto the water pan and place back into position. Secure the

water pan by replacing the mounting screw.

13. Check the following:

• Drain cap from the water pan is securely in place. If the

drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

• Hose from water pan is inserted into storage bin drain

opening.

14. Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then

tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

15. Replace the cutter grid cover.

16. Gently wipe the control panel with a soft, clean dishcloth using warm water and a mild liquid dish detergent.

17. Plug in ice maker or reconnect power.

18. After cleaning, make sure that all controls are set properly and that no control indicators are flashing.

5. Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6. Replace lower access panel and screws.

7. Drain water from water pan by removing the drain cap.

8. If the room temperature will drop below 32°F (0°C), water must be removed from the drain line.

For Ice Makers with a Drain Pump Installed:

• Plug in ice maker or reconnect power.

• Turn ice maker off and remove all remaining ice from ice

bin.

• Pour 1 qt (0.95 L) of water into the ice bin near the drain

and let the ice maker stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain

pump so that the pump will remove the remaining water

from the ice bin and the drain pump.

• Unplug ice maker or disconnect power.

9. Before using again, clean the ice maker and storage bin.

10. Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently lubricated at the factory. They should not require any additional

oiling throughout the normal life of the machine.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

PROBLEM RECOMMENDED SOLUTIONS

Ice Maker Will Not Check that it is plugged into a grounded 3 prong outlet.

Operate Check that the control is turned on. See "Using the Controls."

Replace the fuse or reset the circuit breaker. NOTE: If problems continue, contact an electrician.

Room temperature must be above 55°F (13°C). Otherwise, bin thermostat may sense cold room

temperature and shut off even though the bin is not full of ice. The ice maker may not restart once it

does shut off. Ifthere was a large amount of water added to the ice maker, wait a few minutes for the drain pump to

clear. If there is still water in the bin, check to see whether the drain hose is kinked. For models with drain pumps, check that the drain hose is not damaged, or kinked or pinched

between cabinet and ice maker. Use only Whirlpool approved drain pump kit, Part Number 1901A.

Ice Maker Seems Noisy Is the water in the reservoir overflowing? This is normal. This overflow helps to purge minerals that

were removed from the water during the ice making process.

Is there a "whooshing" sound? Check the following things:

• Check that the water supply is hooked up and turned on.

• Check that the drain cap is tight and the water drain pan pump is securely attached to the water pan.

Is there ice between the evaporator plate and the cutting grid? Check that the ice maker is level. See "Leveling." If the ice maker is level, and the problem persists, run a cleaning cycle. See

"Cleaning." If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud

sound during water filling associated with the flow of water through the inlet valve. Call a licensed,

qualified plumber to determine the best method to reduce the supply water pressure (50 psi is recommended).

Electrical Shock Hazard

Disconnect power before servicing. Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

PROBLEM RECOMMENDED SOLUTIONS

Ice Maker Runs But Produces No Ice

Ice Maker Runs But Produces Very Little Ice

PROBLEM RECOMMENDED SOLUTIONS

Off Taste, Odor or Gray Color in the Ice

Check that the control is turned on. Check that the water supply is properly connected and turned on.

Ifthe drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten the drain cap.

Clean the drain tube. Check that there are no kinks in the drain line.

Is the accelerated ice production feature turned on? This feature increases the ice production rate

to provide you with more ice in the same amount of time. See "Using the Controls."

Room temperatures of more than 90°F (32°C) will normally reduce ice production. Dirt or lint may be blocking the airflow through the condenser. See "Condenser" in the "Cleaning"

section.

Ifthere is white scale buildup in the ice maker's water or freezing system, you should clean the ice

maker. See "Interior Components" in the "Cleaning" section.

Ifthe drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten the drain cap.

Ensure that the cutter grid is securely in place and that its harness plug is connected. See "Interior

Components" section of "Cleaning" for instructions on cutter grid removal. Check that water filter is properly installed.

Is there unusually high mineral content in the water supply? The water may need to be treated. Is there mineral scale buildup? Clean your ice maker. See "Ice Maker System" in the "Cleaning"

section.

Do not store any foods in the ice bin. Check that all packaging materials were removed at the time of installation.

Thin, Soft or Clumps of Ice Is there unusually high mineral content in the water supply? The water may need to be treated.

Is there mineral scale buildup? Clean your ice maker. See "Ice Maker System" in the "Cleaning"

section. Are there clumps of ice in the bin? If ice is not used regularly, it will melt and form clumps. Break

the clumps with the ice scoop provided.

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

PROBLEM RECOMMENDED SOLUTIONS

Water Not Entering Drain Is the drain hose aligned over the drain? Move the ice maker to align the drain. See "Connect

Properly Water Supply."

NOTE: Service technicians cannot repair plumbing problems outside of the ice maker. Call a licensed, qualified plumber.

Before calling for assistance or service, please check "Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

If the problem is not due to one of the items listed in the "Troubleshooting" section,,,

Call the dealer from whom your appliance was purchased, or call Jenn-Air at 1-800-JENNAIR (1-800-536-6247) to locate an

authorized service company. When calling, please know the purchase date and the complete model and serial number of your

appliance. Be sure to retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem, write to:

Jenn-Air Brand Home Appliances Customer eXperience Center

553 Benson Road Benton Harbor, MI 49022-2692

Web address: www.jennair.com Or call: 1-800-JENNAIR (1-800-536-6247)

If the problem is not due to one of the items listed in the "Troubleshooting" section,,,

Call the dealer from whom your appliance was purchased, or call Jenn-Air at 1-800-JENNAIR (1-800-536-6247) to locate an authorized service company. When calling, please know the

purchase date and the complete model and serial number of your appliance. Be sure to retain proof of purchase to verify warranty

status. If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances Customer eXperience Centre 200 - 6750 Century Ave.

Mississauga, ON L5N 0B7 Web address: www.jennair.ca Or call: 1-800-JENNAIR (1-800-536-6247).

When calling, please know the purchase date and the complete model and serial number of your appliance. This information will

help us to better respond to your request.

U.S. customers using -I-I-Yfor deaf, hearing impaired or speech impaired, call: 1-800-688-2080.

NOTE: When writing or calling about a service problem, please include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt). User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer eXperience Center.

NOTE: When writing or calling about a service problem, please include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt). User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer eXperience Centre.

To order accessories, in the U.S.A., visit our web site www.jennair.com/accessories or call 1-800-536-6247. In Canada, visit our web site www.whirlpoolparts.ca or call 1-800-807-6777. Water Filter

Order Part Number F2WC911or ICE2 Cleaner

Order Part Number 4396808 affresh ®* Stainless Steel Cleaner

In U.S.A., order Part Number W10355016 In Canada, order Part Number W10355016B

*¢_affreshis a trademark of Whirlpool, U.S.A.

affresh ®* Stainless Steel Wipes In U.S.A., order Part Number W10355049

In Canada, order Part Number W10355049B affresh ®* Kitchen & Appliance Cleaner

In U.S.A., order Part Number W10355010 In Canada, order Part Number W10355010B

PERFORMANCE DATA SHEET

Ice Maker Water Filtration System

Model P6GEG2KL, P6KG2KL, P6WG2KL Capacity 2000 Gallons (7571 Liters)

System tested and certified by NSF International against NSF/ANSI

Standard 42 for the reduction of Chlorine Taste and Odor.

This system has been tested according to NSF/ANSI Standards 42 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSl Standards 42.

Substance Reduction NSF Reduction Average InfluentChallenge Maximum Average Minimum %

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction

ChlorineTaste/Odor 150%reduction 11.9727mg/LI2.0mg/L+10% 10.71mg/L 10.7788mg/L 170.2

Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.50 gpm (1.89 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 2000 gallons (7571 liters).

• It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised.

• Use replacement filter P6RFWG2K, P6RFGEG2K,

P6RFKG2K, Part Number ICE2.

Style 1 - When the water filter status display changes from

"GOOD" to "ORDER," order a new filter. When the filter

indicator reads "REPLACE," it is recommended that you

replace the filter.

Style 2 - Press FILTER to check the status of your water filter.

If the filter indicator light is yellow and the words "ORDER

FILTER" appear on the display screen, order a new filter. If the

filter indicator light is red, it is recommended that you replace

the filter.

• These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory

conditions, actual performance may vary.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system.

• Refer to the "Warranty" section for the Manufacturer's name, address and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well Water Pressure 30 - 120 psi (207 - 827 kPa) Water Temperature 33°- 100°F (0.6° - 37.8°C)

Service Flow Rate 0.50 gpm (1.89 Lpm) @ 60 psi

Average % Reduction

I72.81

® NSF is a registered trademark of NSF International.

+ 50 hidden pages