Jenn-Air JIM158XWRS1, JIM158XWRS0, JIM158XWRB0, JIM158XBRS2, JIM158XBRS1 Owner’s Manual

...

JENN-AIR_ICEMAKER/

F._.BRICA.DEHIELOJENN-AIR_/

MACHINEA GLA(_ONSJENN-AII_

USE& CAREGUIDE

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6247} or visit our website at www.jennair.com

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

MANUAL DEUSOY CUIDADO

Si tiene preguntas respecto alas caracteristicas, funcionamiento, rendimiento, partes, accesorios o servicio tecnico, Ilame al:

1-800-JENNAIR (1-800-536-6247} o visite nuestro sitio web en www.jennair.com

En CanadA, Ilame al: 1-800-807-6777, o visite nuestro sitio web en www.jennair.ca.

GUIDED'UTILISATIONETD'ENTRETIEN

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web a www.jennair.ca.

Table of Contents/lndice/Table des matieres ...................................................................................... 2

_°JENN-AIRo

W10122019A

TABLEOFCONTENTS

ICE MAKER SAFETY ...................................................................... 3

INSTALLATION INSTRUCTIONS .................................................. 3

Unpack the Ice Maker .................................................................. 3

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 4

Water Supply Requirements ........................................................ 4

Leveling ........................................................................................ 5

Connect Water Supply ................................................................. 5

Drain Connection ......................................................................... 6

Ice Maker Door ............................................................................. 7

Normal Sounds ............................................................................ 9

ICE MAKER USE ............................................................................ g

How Your Ice Maker Works ......................................................... 9

Using the Controls ..................................................................... 10

INDICE

SEGURIDAD DE LA FABRICA DE HIELO .................................. 16

INSTRUCCIONES DE INSTALACION ......................................... 16

Desempaque la fabrica de hielo ................................................ 16

Requisitos de ubicaciGn ............................................................. 17

Requisitos electricos .................................................................. 17

Requisitos del suministro de agua ............................................. 18

NivelaciGn ................................................................................... 18

ConexiGn del suministro de agua .............................................. 18

ConexiGn del desagOe ............................................................... 19

Puerta de lafabrica de hielo ...................................................... 20

Sonidos normales ...................................................................... 22

USO DE SU FABRICA DE HIELO ................................................ 22

CGmo funciona su fabrica de hielo ............................................ 22

Uso de los controles .................................................................. 23

ICE MAKER CARE ........................................................................ 10

Cleaning ...................................................................................... 10

Vacation and Moving Care ......................................................... 12

TROUBLESHOOTING .................................................................. 13

Ice Maker Operation ................................................................... 13

Ice Production ............................................................................ 13

Ice Quality ................................................................................... 14

Plumbing Problems .................................................................... 14

ASSISTANCE OR SERVICE ......................................................... 14

In the U.S.A................................................................................ 14

In Canada ................................................................................... 14

WAR RANTY .................................................................................. 15

CUIDADO DE SU FABRICA DE HIELO ....................................... 23

Limpieza ..................................................................................... 23

Cuidado durante las vacaciones y mudanzas ........................... 25

SOLUCli_N DE PROBLEMAS ...................................................... 26

Funcionamiento de la fabrica de hielo....................................... 26

ProducciGn de hielo ................................................................... 27

Calidad del hielo ......................................................................... 27

Problemas de plomerfa .............................................................. 27

AYUDA O SERVIClO TI_CNICO ................................................... 28

En los EE.UU.............................................................................. 28

En Canada .................................................................................. 28

GARANTiA ..................................................................................... 2g

TABLEDESMATIERES

S¢:CURITI:!:DE LA MACHINE A GLAQONS ................................ 30

INSTRUCTIONS D'INSTALLATION ............................................ 30

Deballage de la machine a gla(_ons ........................................... 30

Exigences d'emplacement ......................................................... 31

Specifications electriques .......................................................... 31

Specifications de I'alimentation en eau ..................................... 31

Nivellement ................................................................................. 32

Raccordement a la canalisation d'eau ...................................... 32

Raccordement au conduit d'evacuation ................................... 33

Porte de la machine &glagons .................................................. 34

Sons normaux ............................................................................ 36

UTILISATION DE LA MACHINE ._.GLAQONS ............................ 36

Fonctionnement de la machine a gla(_ons................................. 36

Utilisation des commandes ........................................................ 37

ENTRETIEN DE LA MACHINE ._ GLAQONS .............................. 37

Nettoyage ................................................................................... 37

Precautions a prendre avant les vacances

ou un demenagement ................................................................ 39

DC:PANNAGE ................................................................................. 40

Fonctionnement de la machine a gla(_ons................................. 40

Production de gla(_ons ............................................................... 41

Qualite des gla(_ons.................................................................... 41

Problemes de plomberie ............................................................ 41

ASSISTANCE OU SERVICE ......................................................... 42

Aux Ctats-Unis ............................................................................ 42

Au Canada .................................................................................. 42

GARANTIE ..................................................................................... 43

ICEMAKERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before cleaning.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Use two or more people to move and install ice maker.

SAVE THESE INSTRUCTIONS

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

• To remove any remaining tape or glue from the exterior of the ice maker, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. Do not

use chlorine bleach on the stainless steel surfaces of the ice maker. These products can damage the surface of your ice

maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in

the "Ice Maker Care" section.

Toensureproperventilationforyouricemaker,thefrontside mustbecompletelyunobstructed.Theunitmaybeclosed-in onthetopandthreesides,buttheinstallationshouldallow theicemakertobepulledforwardforservicingifnecessary.

Installation of the ice maker requires a cold water supply inlet of 1/4"(6.35 mm) OD soft copper tubing with a shutoff valve and either a gravity-drain system or condensate pump to carry the water to an existing drain.

Choose a well ventilated area with temperatures above 55°F (13°C) and below 110°F (43°C). Best results are obtained between 70°F (21°C) and 90°F (32°C).

This unit must be installed in an area protected from the elements, such as wind, rain, water spray, or drip.

When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as

shown. NOTE:

• Be sure the power supply cord is not pinched between

the ice maker and the cabinet.

• Be sure the water supply line is not pinched between the

ice maker and the cabinet.

• Be sure the drain line (on some models) is not pinched

between the ice maker and the cabinet.

_1 I-

34"

(86.4 cm)

Min.

341/2"

(87.6 cm)

Max.

281/2"

(72.4 cm)

i _,+..,/%_I II+ +.,ii %_ I <,i,

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your ice maker into its final location, it is important to make sure you have the proper electrical

connection: A 115 Volt, 60 Hz., AC only, 15- or 20-amp electrical supply,

properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required.

It is recommended that a separate circuit, serving only your ice maker, be provided. Use a receptacle which cannot be turned off by a switch or pull chain.

IMPORTANT: Ifthis product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Ice quality may be affected. If nuisance tripping has occurred, and if the condition of the ice appears poor, dispose of it.

Recommended grounding method

For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3 prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, grounding-type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. Ifa mating wall receptacle is not available, it is the personal responsibility of the customer to have a properly grounded, 3 prong wall receptacle installed by a qualified electrician.

_'_ 15"'_

(38,1 cm)

A.Recommended location for electrical

andplumbing fixtures

B.Floor level

You should choose a location where the floor is even. It is important for the ice maker to be level in order to work

properly. If needed, you can adjust the height of the ice maker by changing the height of the leveling legs. See "Leveling."

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the ice maker needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa). The reverse osmosis system must provide 1 gal. (3.79L) of water per hour to the ice maker for proper ice maker operation.

Ifthewaterpressuretothereverseosmosissystemislessthan 40to60psi(276to414kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

It is important for the ice maker to be level in order to work properly. Depending upon where you install the ice maker, you may need to make several adjustments to level it. You may also use the leveling legs to lower the height of the ice maker for

undercounter installations.

Tools needed:

Gather the required tools and parts before starting installation.

• 9" level

• Adjustable wrench

NOTE: It is easier to adjust the leveling legs if you have another person to assist you.

1. Move the ice maker to its final location. NOTE: If this is a built-in installation, move the ice maker as

close as possible to the final location.

2. Place a carpenter's level on top of the product to see if the ice maker is level from front to back and side to side.

3. Push up on the top front of the ice maker, and then locate the leveling screws that are on the bottom front of the ice maker.

4. Using an adjustable wrench, change the height of the legs as follows:

• Turn the leveling leg to the right to lower that side of the

ice maker.

• Turn the leveling leg to the left to raise that side of the ice

maker.

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

5. Push up on the top rear of the ice maker and locate the leveling legs that are on the bottom rear of the ice maker.

6. Follow the instructions in Step 4 to change the height of the legs.

7. Use a carpenter's level to recheck the ice maker to see that it is even from front to back and side to side. If the ice maker is

not level, repeat steps 2 to 5. If the ice maker is level, go to the "Connect Water Supply" section.

Read all directions thoroughly before you begin, IMPORTANT:

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and

ordinances.

• Use copper tubing and check for leaks.

• Install copper tubing only in areas where temperatures will remain above freezing.

Tools needed:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

• Flat-blade screwdriver

• 7/16"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

• 1/4"drill bit

• Hand drill or electric drill properly grounded

NOTE: Your ice maker dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/16" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Connecting the water line

Turn off main water supply. Turn on nearest faucet long enough to clear line of water.

Find a 1/2"(12.70 mm) to 11/4'' (3.18 cm) vertical cold water pipe near the ice maker.

NOTE: Horizontal pipe will work, but the following procedure must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten the pipe clamp or you may crush cold water pipe if it is soft copper tubing. Do not use a piercing-type or 3/ld' (4.76 mm) saddle-type valve which reduces water flow and clogs more easily.

Now you are ready to connect the copper tubing. Use 1/4" (6.35 mm) OD soft copper tubing for the cold water supply.

• Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut

square.

• Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

....... ................... A

H_ ...............B

Thread the nut onto the coupling on the end of the copper tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet's side wall or other parts inside the cabinet.

A B C

A. Line to ice maker

B.Nut (purchased)

C. Ferrule(purchased)

D E F G

E.Ferrule R Nut

G.Supplied line from ice maker

D. Coupling (purchased)

A.Cold water pipe E.Compression nut B.Pipe clamp F Compression sleeve C.Copper tubing G.Shutoff valve D.Coupling (purchased) H.Packing nut

Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is

clear. Turn off shutoff valve on the water pipe. NOTE: Always drain the water line before making the final

connection to the inlet of the water valve to avoid possible water valve malfunction.

7. Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown.

Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

REAR VIEW

A. Drain hose (drain pump models only) B. Vent hose (drain pump models only) C. Water supply line

9. Turn shutoff valve ON.

10. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

...... C;on ec

Gravity Drain System

Connect the ice maker drain to your drain in accordance with all state and local codes and ordinances. Ifthe ice maker is

provided with a gravity drain system, follow these guidelines when installing drain lines. This will help keep water from flowing

back into the ice maker storage bin and potentially flowing onto the floor causing water damage.

• Drain lines must have a minimum of %" (15.88 mm) inside diameter.

• Drain lines must have a 1" drop per 48" (2.54 cm drop per 122 cm) of run or _/4"drop per 12" (6.35 mm per 30.48 cm) of

run and must not have low points where water can settle.

• The floor drains must be large enough to accommodate drainage from all drains.

The ideal installation has a standpipe with a 11/2"(3.81 cm) to 2" (5.08 cm) PVC drain reducer installed directly below the

outlet of the drain tube as shown. You must maintain a 1" (2.54 cm) air gap between the drain hose and the standpipe.

• It may be desirable to insulate the drain line thoroughly up to the drain inlet.

SIDE VIEW

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

I I

3%"

(9.2 cm) Y

(58,4 cm)

A. Drain hose B. 1" (2.54 cm) air gap

C. PVC drain reducer D. Center of drain should be 23" (58.4 cm) from front of door,

with or without the 3/4"(1.91 cm) panel on the door: The drain should also be centered from left to right (7_J'

[18.56 cm] from either side of the ice maker).

23" C

2" - 11/2''

(5 cm- 3.8 cm)

Drain Pump System (on some models)

Connect the ice maker drain to your drain in accordance with the International Plumbing Code and any local codes and

ordinances. NOTE: If the drain hose becomes twisted and water cannot

drain, your ice maker will not work.

Connecting the Drain

2. Style 1 - For gravity drain system, push the ice maker into position so that the ice maker drain tube is positioned over the PVC drain reducer. See "Gravity Drain System" earlier in this section. Style 2 - For drain pump system connect the drain pump outlet hose to the drain. See "Drain Pump System" earlier in this section.

3. Recheck the ice maker to be sure that it is level. See "Leveling."

4. If it is required by your local sanitation code, seal the cabinet to the floor with an approved caulking compound after all

water and electrical connections have been made.

", ©oo%.® _, _,_,,.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• 5/16"wrench • Flat putty knife

• 1/4"wrench • Phillips screwdriver

Hinge pin

5/16"Hex-head hingescrew

After ensuring that the drain system is adequate, follow these steps to properly place the ice maker:

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

f. Plug ice maker into a grounded 3 prong outlet.

Handle screw End Cap screw

Remove Door

1. Unplug ice maker or disconnect power.

2. Remove the handle screws and handle from the top of the door (on some models). Keep the parts together and set them

aside.

3. Remove the hinge pin from the top hinge.

4. Remove the door from the hinges and screw the top hinge pin back into the top hinge.

5. Remove the door skin (on some models) as follows:

• Remove the two screws from the top and bottom of the

door skin.

• Remove the skin and the edge protectors from the door.

Keep the parts together and set them aside.

Reverse the door end caps as follows:

• Remove the screw and end cap from the top corner. Move it diagonally to the opposite side's bottom corner, keeping the straight side of the end cap facing the front of

the ice maker. Remove the screw and end cap from the bottom corner.

Move it diagonally to the opposite side's top corner, keeping the straight side of the end cap facing the front of

the ice maker.

A. Top Comer Open (no end cap)

B. Beginning Top Comer End Cap C. Beginning Bottom Corner End Cap D. Bottom Corner Open (no end cap)

7. Place the door back into the stainless skin, keeping the edge protectors in place. Replace the two screws in the top and

bottom.

8. Set the door aside.

Replace Door

1. Place plastic hinge pin sleeve in the top hinge hole on the door. Align the door with the top hinge hole and replace the top hinge pin.

2. Replace the handle and handle screws (on some models).

Top Hinge

............... A

........... B

SI:::............c

A. Hingepin C.Hinge B. Hingepin sleeve

Bottom Hinge

"_ _ _ii_iii_:::> oA

D. Hex-head hinge screw

Reverse Hinges

1. Unscrew and remove the top hinge. Replace the screws in the empty hinge holes.

2. Remove the screws from the bottom of the opposite side of the ice maker cabinet. Turn the top hinge upside down so that the hinge pin points up. Place the hinge on the bottom

opposite side of the ice maker and tighten screws.

3. Remove the plastic hinge pin sleeve from the "old" bottom hinge and replace it on the new bottom hinge pin.

4. Remove the "old" bottom hinge screws and hinge. Replace the screws in the empty hinge holes.

5. Remove the screws from the top of the opposite side of the ice maker cabinet. Turn the hinge upside down so that the hinge pin points down. Place the hinge on the top opposite side of the ice maker and tighten the screws.

6. Remove the top hinge pin.

/ & .............................D

A. Hex-head hinge screw C. Hinge B. Hinge pin sleeve D.Hinge pin

Reverse Door Catch

Remove the hole plugs from the opposite side of the door and set aside.

Remove the screws from the magnetic door catch and re )lace it on the opposite side of the door.

=j0 o

3. Push the hole plugs into place on the opposite side of the door.

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

ICEMAKERUSE

When you first start your ice maker, the water pan will fill and the system will rinse itself before starting to make ice. The rinsing process takes about 5 minutes.

Under normal operating conditions, the ice maker will cycle at preset temperatures. The ice level sensor located in the ice

storage bin will monitor the ice levels.

IMPORTANT:

• If the water supply to the ice maker is turned off, be sure to set the ice maker control to OFR

• The ice maker is designed to make clear ice from the majority of water sources on a daily basis. If your results are

unsatisfactory, your water may need to be filtered or treated.

The Ice Making Process

4. Plug in ice maker or reconnect power.

Your new ice maker may make sounds that are not familiar to you. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces such as floors, walls and cabinets can make the sounds

seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them.

• You will hear a buzzing sound when the water valve opens to fill the water reservoir for each cycle.

• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the ice maker can also

make noises.

• The high-efficiency compressor may make a pulsating or high pitched sound.

• Water running over the evaporator plate may make a splashing sound.

• Water running from the evaporator plate to the water reservoir may make a splashing sound.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your ice maker.

• You may hear air being forced over the condenser by the condenser fan.

• During the harvest cycle, you may hear a "thud" when the ice sheet slides from the evaporator onto the cutter grid.

• When you first start the ice maker, you may hear water running continuously. The ice maker is programmed to run a rinse cycle before it begins to make ice.

Water is constantly circulated over a freezing plate. As the water freezes into ice, the minerals in the water are rejected. This produces a sheet of ice with a low mineral content.

2. When the desired thickness is reached, the ice sheet is released and slides onto a cutter grid. The grid divides the

sheet into individual cubes.

3. The water containing the rejected minerals is drained after each freezing cycle.

4. Fresh water enters the machine for the next ice making cycle.

5. Cubes fall into the storage bin. When the bin is full, the ice maker shuts off automatically and restarts when more ice is needed. The ice bin is not refrigerated, and some melting will occur. The amount of melting varies with room temperature.

NOTE: As the room and water temperatures vary, so will the amount of ice produced and stored. This means that higher operating temperatures result in reduced ice production.

To start the normal ice making cycle, press ON.

To stop ice maker operation, press and hold OFE

On Control Clean

Off Lock Service R e s e t

_,,_',_ !i_ ,,_ ",_*" .....

1. To lock the control panel, press and hold the Control Lock button until the indicator appears,

2. To unlock the control panel, press and hold the Control Lock button until the indicator disappears,

Service

O-O-O-O

NOTE:

• Pressing the ON/OFF switch does not shut off power to the ice maker.

• Allow 24 hours to produce the first batch of ice. Discard the first batch produced.

Control Lock

The control panel can be turned off for easy cleaning or to avoid unintentional activation by children or small pets.

NOTE: The control lock feature does not shut off power to the ice maker or to the ice maker bin light. It simply deactivates the

control panel.

ICEMAKERCARE

The ice making system and the air cooled condenser need to be cleaned regularly for the ice maker to operate at peak efficiency and to avoid premature failure of system components, See the

"Ice Maker System" and the "Condenser" sections.

Exterior Surfaces

Wash the exterior enamel surfaces and gaskets with warm water and mild soap or detergent. Wipe and dry. Regular use of a good household appliance cleaner and wax will help protect the finish. Do not use abrasive cleaners on enamel surfaces as they may

scratch the finish. For products with a stainless steel exterior, use a clean sponge or

soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, Do not use chlorine bleach on the stainless steel surfaces.

The service light indicates when service is needed. If the service light turns on, turn the ice maker off and back on, If the service light turns on again, call for service.

_sssss_

Clean/Reset

The Cleaning/Reset Status light will help you know when it is time to clean your ice maker. The light will change to yellow. This tells you it is almost time to clean your ice maker. It is recommended that you clean the ice maker when the status light changes to red OR ice production decreases significantly. To clean your ice maker, see "Ice Maker System."

4. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan and you will

have either thin ice or no ice,

5. Read and follow all handling information on the cleaner bottle before completing the steps below, Use one 16 oz (473 mL)

bottle of approved ice maker cleaner.

6. Pour one bottle of solution into the water pan. Fill the bottle twice with tap water and pour it into the water pan,

B ..............

Ice Maker System

Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup, How often you need to clean the system depends upon how hard your water is. With hard water of 15 to 20 grains/gal, (4 to 5 grains/liter), you may need to clean the system as often as every 6 months.

NOTE: Use one 16 oz (473 mL) bottle of approved ice maker cleaner. To order, call 1-800-JENNAIR and ask for Part Number

4396808. In Canada, call 1-800-807-6777,

1. Press and hold the selector switch to OFR

2. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove all ice from the storage bin.

3. Unscrew the drain cap from the bottom of the water pan located inside the storage bin as shown. Allow the water to drain completely.

,. 0

A. _ater pan

B.Waterpan thumb screws C.Draincap

7. Press and hold the CLEAN button. See "Using the Controls." The light will blink, indicating that the cleaning cycle is in process. When the indicator light turns green (approximately 70 minutes), the cleaning cycle is complete, During the cleaning cycle, the system will both clean and rinse itself.

8. After the cleaning cycle is complete, remove the drain cap from the water pan, Look for any cleaning solution left in the water pan. If cleaning solution drains from the water pan, you should run the clean cycle again, Be sure to replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan and you will have either thin ice

or no ice.

NOTE: Severe scale buildup may require repeated cleaning with a fresh quantity of cleaning solution,

9. Push the selector switch to ON to resume ice production.

Condenser

Interior Components

A dirty or clogged condenser:

• Obstructs proper airflow.

• Reduces ice making capacity.

• Causes higher than recommended operating temperatures which may lead to component failure.

Electrical Shock Hazard

Disconnect power before cleaning. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

1. Unplug ice maker or disconnect power.

2. Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel

support. Pull forward to remove the lower access panel.

3. Pull the bottom forward and then pull down to remove the lower access panel.

1. Unplug ice maker or disconnect power.

2. Open the storage bin door and remove any ice that is in the bin.

3. Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

4. Remove the two screws that hold the cutter grid cover in place and remove the cutter grid cover.

5. Unplug the wiring harness from the left side of the cutter grid.

A. Cutter grid cover B. Screws

6. Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

7. Remove the right-hand and left-hand screws. Lift the cutter grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

4. Remove dirt and lint from the condenser fins and the unit

compartment with a brush attachment on a vacuum cleaner.

5. Replace the lower access panel using the four screws.

6. Plug in ice maker or reconnect power.

A.Cutter grid harness D.Ice level sensor harness B.Screw E.Plasticspacer C.Cutter grid F. Screw

Remove the two thumb screws that hold the water pan in place. Push down with one hand on the front of the pan while pulling forward on the bottom back side.

B'--

"1_\1k

A.Water pan B.Water pan thumb screws C.Draincap

Remove, clean and replace the ice scoop and ice scoop holder.

• After removing the ice scoop, remove the holder by removing the two thumb screws.

• Wash the ice scoop holder along with the other interior components using the following instructions.

• Replace the ice scoop holder by replacing the thumb screws.

A. Thumb screw B. Ice scoop holder

f0. Wash the interior components (cutter grid, exterior of hoses,

and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

11. Replace water pan by pushing back on the bottom with one hand while pushing up and back on thetop. Secure the water pan by replacing both screws.

12. Check the following:

• Drain cap from the water pan is securely in place. If the

drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

• Hose from water pan is inserted into storage bin drain

opening.

13. Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid

harness and the ice level sensor harness.

14. Replace the cutter grid cover and the two screws.

15. Plug in ice maker or reconnect power.

,_ ,_ ,_y_'_ ..... _ _ %J ¢_+,,,/¸

Electrical Shock Hazard

Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

To shut down the ice maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from storage bin.

3. Shut off the water supply.

4. Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

5. Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6. Replace lower access panel and screws.

7. Drain water from water pan by removing the drain cap.

8. If the room temperature will drop below 32°F (0°C), remove water from the drain line.

For ice makers with a drain pump installed:

• Plug in ice maker or reconnect power.

• Turn ice maker off and remove all remaining ice from ice

bin.

• Pour 1 qt (0.95 L) of water into the ice bin near the drain

and let the unit stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water from the ice bin and the drain pump.

• Unplug ice maker or disconnect power.

9. Before using again, clean the ice maker and storage bin.

10. Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

Your ice maker will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Is there ice between the evaporator plate and the cutting grid? Check to be sure that the ice maker is level. See

"Leveling." If the ice maker is level, and the problem persists, run a cleaning cycle. See "Cleaning."

Ice maker runs but produces no ice

• Is the control set to ON? Be sure that the control is set to ON.

• Is the water supply connected? Make sure the water supply is properly connected and turned on.

• Is the drain cap securely in place? If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten the drain cap.

• is there debris in the drain tube? Clean the drain tube.

• Is there a kink in the drain line? Be sure that there are no kinks in the line.

• Is the service light flashing on and off continually? Call for service.

Is the power cord plugged in? Plug into a grounded 3 prong outlet.

Is the control set to ON? Be sure that the control is set to

ON.

Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. Ifthe

problem continues, call an electrician. Is the room temperature cooler than normal? Room

temperature must be above 55°F (13°C). Otherwise, bin thermostat may sense cold room temperature and shut off even though the bin is not full of ice. Also, unit may not restart

once it does shut off.

Does the red light come on when the Clean button is

pushed? The ice maker is receiving power but may need cleaning. See "Cleaning."

Does the ice maker have a drain pump? Ifthere was a large amount of water added to the ice maker, wait a few minutes for the drain pump to clear. If there is still water in the bin,

check to see whether the drain hose is kinked.

Ice maker seems noisy

• Is water being circulated through the ice maker? This is normal operation. Water is added once per ice-making cycle.

• is the water in the reservoir overflowing? This is normal. This overflow helps to purge minerals that were removed from the water during the ice making process.

• Is there a "whooshing" sound? Check the following things:

• Make sure that the water supply is hooked up and turned

On.

• Make sure that the drain cap is tight and the water drain

pan pump is securely attached to the water pan.

Ice maker runs but produces very little ice

• Is the room temperature hotter than normal? Room temperatures of more than 90°F (32°C) will normally reduce ice production.

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

• Is the condenser dirty? Dirt or lint may be blocking the airflow through the condenser. See "Condenser."

• Is there scale buildup in the ice maker? If there is white scale buildup in the ice maker's water or freezing system, you should clean the ice maker. See "Interior Components" in the "Cleaning" section.

• Is the drain cap securely in place? If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. Tighten the drain cap if it is loose.

Grid is not cutting ice sheets

• Is the cutter grid securely in place? Check the cutter grid harness plug to make sure the connection is intact. See "Interior Components" section of "Cleaning" for instructions on cutter grid removal.

Off taste, odor or gray color in the ice

• Is there unusually high mineral content in the water supply? The water may need to be filtered or treated.

is there mineral scale buildup? Clean your ice maker. See "Ice Maker System" in the "Cleaning" section,

Are there food items stored in the ice bin? Do not store any foods in the ice bin.

Were all the packaging materials removed? Make sure that

all packaging materials were removed at the time of installation.

Is there mineral scale buildup? Clean your ice maker. See "Ice Maker System" in the "Cleaning" section.

Are there clumps of ice in the bin? If ice is not used regularly it will melt and form clumps. Break the clumps with the ice scoop provided,

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Thin, soft or clumps of ice

• Is there unusually high mineral content in the water supply? The water may need to be filtered or treated,

ASSISTANCEORSERVICE

Before calling for assistance or service, please check "Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below. When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will help us to better respond to your request.

If the problem is not due to one of the items listed in the

"Troubleshooting" section... Call the dealer from whom your appliance was purchased, or call

Jenn-Air Brand Home Appliances, Customer eXperience Center at 1-800-JENNAIR (1-800-536-6247) to locate an authorized service company. When calling, please know the purchase date and the complete model and serial number of your appliance. Be sure to retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem, write to:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Web address: www.jennair.com

Or call: 1-800-JENNAIR (1-800-536-6247). U.S. customers using TTY for deaf, hearing impaired or speech

impaired, call: 1-800-688-2080 (Monday - Friday, 8:00 a.m. - 8:00 p.m. Eastern Time).

NOTE: When writing or calling about a service problem, please include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are available from Jenn-Air Brand Home Appliances, Customer eXperience Center.

• Is the drain hose aligned over the drain? Move the ice maker to align the drain. See "Water Supply Connection."

NOTE: Service technicians can not repair plumbing problems outside of the ice maker. Call a licensed, qualified plumber.

_% P rtl!" p_ '!¢_

If the problem is not due to one of the items listed in the

"Troubleshooting" section... Call the dealer from whom your appliance was purchased, or call

Jenn-Air Brand Home Appliances, Customer Interaction Centre at

1-800-807-6777 to locate an authorized service company. When calling, please know the purchase date and the complete model and serial number of your appliance. Be sure to retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem, write to:

Jenn-Air Brand Home Appliances

Customer Interaction Centre

1901 Minnesota Court

Mississauga, ON L5N 3A7

Web address: www.jennair.ca

Or call: 1-800-807-6777, NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are available from Jenn-Air Brand Home Appliances, Customer

Interaction Centre.

+ 30 hidden pages