JENNAIR JIM158XBCX, JIM158XBRB, JIM158XBRS, JIM158XWRB, JIM158XWRS Dimension Guide

Ice Maker

PRODUCT MODEL NUMBERS

JIM158XB JIM158XW

Electrical: 115-Volt, 60-Hz, AC-only 15or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator drawers be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) equipped outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

Water: A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate ice maker and water dispenser. If you have questions about your water pressure, call a licensed, qualified plumber.

IMPORTANT: The pressure of the water coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

Reverse Osmosis Water Supply: If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

CABINET OPENING DIMENSIONS

A. Recommended location for

electrical and plumbing

fixtures.

B. Floor level

11¹⁄

"

A

■ Be sure the power supply

(29.2 cm)

cord is not pinched between

34"

the ice maker and the

(86.4 cm)

cabinet.

Min.

28¹⁄ "

■ Be sure the water supply line

34¹⁄ "

(87.6 cm)

(72.4 cm)

is not pinched between the

Max.

3¹⁄ "

9"

ice maker and the cabinet.

(8.9 cm) (22.9 cm)

■ Be sure the drain line (on

some models) is not pinched

B

between the ice maker and

the cabinet.

24"

■ Choose a location where the

(60.1 cm)

floor is even. It is important

for the ice maker to be level

in order to work properly.

15"

(38.1 cm)

PRODUCT DIMENSIONS

33 ¹³⁄ "

(85.9 cm) Min.

34 ⁄ "

(87.1 cm) Max. with leveling legs fully extended

14 ⁄ "

(37.2 cm)

25 ⁄ "

(65.1 cm)

23 ¹⁄ " (58.7 cm)

DRAIN REQUIREMENTS

Drain: Either a gravity-drain system or condensate pump to carry water to an existing drain.

	Drain lines must have a minimum of 5⁄8"
A	(15.88 mm) inside diameter.

		B	Drain lines must have a 1" drop per 48"
	7 5/16"		(2.54 cm drop per 122 cm) of run or 1⁄4"
A			drop per 12" (6.35 mm per 30.48 cm) of
	(18.58 cm)	3 5/8"
		(9.2 cm)	run and must not have low points where
B		1" (2.54 cm)	water can settle.

23"

C

The floor drains must be large enough to

(58.4 cm)

accommodate drainage from all drains.

D

The ideal installation has a standpipe with

(14.5 cm)

2" - 1 5/8"

2 7/8"

5 11/16"

(7.27 cm)

(5 cm - 3.8 cm)

a 11⁄2" (3.81 cm) to 2" (5.08 cm) PVC drain

14 5/8"

A. Drain hose

D. Center of drain should be 23" (58.4 cm)

reducer installed directly below the outlet

(37.2 cm)

B. 1" (2.54 cm)

from front of door, with or without the

of the drain tube as shown. You must

maintain a 1" (2.54 cm) air gap between

A. Water Pan Drain

3⁄4" (1.91 cm ) panel on the door. Then

air gap

B. Water Valve

C. PVC drain

drain should also be centered from left

the drain hose and the standpipe.

to right (75⁄16" [18.58 cm] from either

It may be desirable to insulate the drain

reducer

side of the ice maker).

line thoroughly up to the drain inlet.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. W10206439-D-JA
Instructions packed with product. Specifications subject to change without notice.	08/27/09