JENN-AIR JGS8850ADB, JGS8850ADQ, JGS8850ADS, JGS8850ADW Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand [phone]

		This Data Sheet Includes Information On
		Jenn-Air
•		Product Model Number (s):			•
		Slide In Gas Ranges:
		JGS8850ADS, JGS8850ADB, JGS8850ADQ and
		JGS8850ADW
•		Dimensions (Actual Size)			•
		Width:	29 7/8"
		Depth:	26 3/16"
		Height:	35	3/4"
		Door swing:	20	1/2"
		Height at full leg adjustment:	36	7/16"
		Height at 0" leg adjustment:	35	3/4"
	•	Additional Information			•

•Units depth including door handle is 28 3/8".

•Can be installed with the back against (0") a vertical combustible wall if equipped with optional backguard kit, and the sides below the cooktop surface against (0") combustible base cabinets.

•Electrical requirements: 120/240 or 120/208VAC,60Hz. 40 or 50 amp grounded circuit protection is required.

•Proper operation requires use of range hood.

•Cabinetry over cooktop : 30" minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet. 24" minimum when bottom of wood or metal cabinet is protected by not less than 1/4" flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum or copper.

•To eliminate the hazard of reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the hazard can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets.

•For Free-standing installations a slide-in range with side panels measures 30 3/4" wide. The height of the countertop is 36" and countertop depth is 25".

•Island or peninsula installations with 24" deep base cabinets must use flush back (no rear toe space) cabinets to avoid range interference,. If rear toe space is desired, use 27" or deeper cabinets.

See page 2 for additional information

Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of deter-
mining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2002.	174

29 7/8"

26 3/16"

(not to scale)

35 3/4"

20 1/2"

	Locate electrical
	supply junction
Wall View	box or 60" of
	electrical cable
(not to scale)	within shaded
	area.
	5 1/2"
5 1/2"	19"
10"
	2 1/4"

Upper cabinets

can only be 13"

Wall View

deep maximum.

(not to scale)

30"

Min.

Over range

cabinet is NOT

recommended.

Minimum horizontal clearance

30"

between the edge of the

appliance and combustible

18"

3" construction extending from

the cooking surface to 18"

above the cooking surface is

3" to the sides and 0" to the

back (see solid areas). 6"

36"

Range

Minimum is recommended.

Countertop

height

30" Minimum cutout width

• NEVER reuse Data Sheets. Data Sheets are subject to change without	• Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily,	• Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data	• Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks	BN220.55 • A174B149 • • 032603 • 95659 • 42689
associated with reusing old Data Sheets.