JENN-AIR JGS1450FP, JGS1450FB Installation Instructions
INSTALLATION INSTRUCTIONS
30" (76.2 CM) SLIDE-IN GAS RANGES
INSTRUCTIONS POUR L’INSTALLATION DES
CUISINIÈRES À GAZ ENCASTRABLES DE 30"
(76,2 CM)
Table of Contents Table des matières
RANGE SAFETY .............................................................................2
INSTALLATION REQUIREMENTS
Tools and Parts
Location Requirements
Electrical Requirements
Gas Supply Requirements
INSTALLATION INSTRUCTIONS
Unpack Range..............................................................................9
Install Anti-Tip Bracket
Adjust Leveling Legs
Level Range
Make Gas Connection
Verify Anti-Tip Bracket Is Installed and Engaged
Electronic Ignition System
Remove/Replace Drawer
Oven Door
Complete Installation
GAS CONVERSIONS
Propane Gas Conversion
Natural Gas Conversion
Adjust Flame Height
.............................................................................4
................................................................4
...............................................................7
.................................................................9
..................................................................10
................................................................................11
...............................................................11
..................................................................................14
.................................................................15
....................................................................16
.............................................................19
...................................................................22
.................................................4
...........................................................7
...................................................9
......................13
.........................................................13
...........................................................14
...........................................................16
SÉCURITÉ DE LA CUISINIÈRE
EXIGENCES D’INSTALLATION
Outils et pièces
Exigences d’emplacement
Spécications électriques
Spécications de l’alimentation en gaz
INSTRUCTIONS D’INSTALLATION
Déballage de la cuisinière
Installation de la bride antibasculement
Réglage des pieds de nivellement
Réglage de l’aplomb de la cuisinière
Raccordement au gaz
Vérier que la bride antibasculement
est bien installée et engagée
Système d’allumage électronique..............................................36
Dépose et réinstallation du tiroir
Porte du four
Achever l’installation
CONVERSIONS POUR CHANGEMENT DE GAZ
Conversion pour l’alimentation au propane
Conversion pour l’alimentation au gaz naturel
Réglage de la taille des ammes
...........................................................................26
................................................................33
..............................................................................37
..................................................................38
...................................................24
...................................................26
.........................................................26
..........................................................29
.....................................29
.............................................31
..........................................................31
....................................31
.............................................32
.........................................33
.....................................................35
................................................37
..............................39
..........................43
...............................................46
......................39
IMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
IMPORTANT :
Installateur : Remettre les instructions d’installation au propriétaire.
Propriétaire : Conserver les instructions d’installation pour référence ultérieure.
W11124003C
RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
Installation and service must be performed by a qualified installer, service agency or
–
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of
ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or
unintended operation.
2
In the State of Massachusetts, the following installation instructions apply:
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.
A flexible gas connector, when used,must not exceed 4 feet (121.9 cm).
Range Foot
Anti-Tip
Bracket
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
3
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Tools Needed
■ Tape measure
■ Phillips screwdriver
■ Flat-blade screwdriver
1
■
/8" (3 mm) at-blade
screwdriver
■ Level
■ Drill
■ Wrench or pliers
■ Pipe wrench
15
■
/16" (2.4 cm) combination
wrench
1
■
/8" (3.2 mm) drill bit
(for wood oors)
■ Marker or pencil
Parts Supplied
Check that all parts are included.
■ Propane/Natural Gas Conversion Kit
■ #10 x 1
■ Anti-tip bracket (inside oven cavity)
5
/8" (4.1 cm) screws (for mounting anti-tip bracket) (2)
Anti-tip bracket must be securely mounted to the back wall
or oor. Thickness of ooring may require longer screws to
anchor bracket to suboor. Longer screws are available from
your local hardware store.
■ For Models:
WEG730H0D
Burner Caps 554
Burner Grates 223
Oven Racks 233
Parts Needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See “Electrical Requirements” and
“Gas Supply Requirements” sections.
IMPORTANT: When the range is used under microwave models:
JMC82808CB-0, JMV9196CB-0, or YJMV9196CB-0, the Door
Bafe Plate Part Number W10737014 must be ordered and
used. Please reference the “Accessories” section of the User
Guide for contact information.
■ Pipe-joint compound
resistant to propane gas
3
■
/16" (4.8 mm)
carbide-tipped masonry
drill bit (for concrete/
ceramic oors)
■ Noncorrosive leak-
detection solution
For propane/Natural Gas
Conversions
5
■
/8" (1.6 cm) combination
wrench
3
■
/8" (1 cm) nut driver
9
■
/32" (7 mm) nut driver
■ Masking tape
KSGG700E
KSGB900E
MGS8880D
WEG760H0DJGS1450D
■ Optional Parts
To purchase these or any other accessories, please reference the
“Accessories” section of the User Guide for contact information.
■ Side Trim Kits:
5
/8" (1.7 cm) White - Order Part Number W10675027
5
/8" (1.7 cm) Black - Order Part Number W10675026
5
/8" (1.7 cm) Stainless Steel - Order Part Number W10675028
11/8" (2.9 cm) White - Order Part Number W10731885
11/8" (2.9 cm) Black - Order Part Number W10731886
11/8" (2.9 cm) Stainless Steel - Order Part Number
W10731887
■ Backsplash Kits:
High 6" (15.2 cm) White - Order Part Number W10655448
High 6" (15.2 cm) Black - Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel - Order Part Number
W10655450
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Do not obstruct ow of combustion and ventilation air.
■ It is the installer’s responsibility to comply with installation
clearances specied on the model/serial/rating plate. The
model/serial/rating plate is located behind the oven door on
the top right-hand side of the oven frame.
■ The range should be located for convenient use in the
kitchen.
■ Recessed installations must provide complete enclosure of
the sides and rear of the range.
■ All openings in the wall or oor where range is to be installed
must be sealed.
■ Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
■ The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see “Install Anti-Tip Bracket”
section.
■ Grounded electrical supply is required. See “Electrical
Requirements” section.
■ Proper gas supply connection must be available. See “Gas
Supply Requirements” section.
■ Contact a qualied oor covering installer to check that the
oor covering can withstand at least 200°F (93°C).
■ Use an insulated pad or ¼" (6.35 mm) plywood under range
if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate or sustain other damage. This
oven has been designed in accordance with the requirements
of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194°F (90°C).
4
Mobile Home - Additional Installation Requirements
B.
C.
D.
screwed in all the way*
" (71.9 cm) max. depth
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD Part 280). When such
standard is not applicable, use the Standard for Manufactured
Home Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-latest edition, or with local
codes.
Mobile Home Installations Require:
■ When this range is installed in a mobile home, it must be
secured to the oor during transit. Any method of securing
the range is adequate as long as it conforms to the
standards listed above.
Product Dimensions
This manual covers several models. Your model may appear
different from the models depicted. Dimensions given are
maximum dimensions across all models.
Model KSGB900
B
A
E
F
C
D
A.1
³⁄₁₆
" (3.0 cm) height from cooktop
to top of vent
29
⁷⁄₈
" (75.9 cm)
Model/serial/rating plate (located
behind the oven door on the top
right-hand side of the oven frame)
36" (91.4 cm) height to top of
cooktop edge with leveling legs
E. 28
⁵⁄₁₆
from front of console to
back of range
" (73.3 cm) max. depth
⁷⁄₈
F. 28
from handle to back of
range
IMPORTANT: Range must be level after installation. Follow the
instructions in the “Level Range” section. Using the cooktop as a
reference for leveling the range is not recommended.
*Range can be raised approximately 1" (2.5 cm) by adjusting the
leveling legs.
5
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm)
countertop height.
IMPORTANT: If installing a range hood or microwave hood combination above the cooking surface, follow the range hood or
microwave hood combination installation instructions for dimensional clearances above the cooktop surface.
Range may be installed next to combustible walls with zero clearance.
NOTE: When installed in a slide-in cutout, the front of oven door may protrude beyond the base cabinet.
tuotuC gnidnatseerFtuotuC nI-edilS
B
D
C
N
A
E
M
F
H
I
G
L
K
J
A. 18" (45.7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE*.
E. 30" (76.2 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of range to side wall or
other combustible material
G. The shaded area is recommended for installation of rigid gas pipe
and grounded outlet.
¹⁄₈
" (33.3 cm)
H. 13
¹¹⁄₁₆
" (19.5 cm)
I. 7
¹³⁄₁₆
" (12.2 cm)
J. 4
K. 3
¹¹⁄₁₆
" (9.4 cm) plus measurement of N
L. 12" (30.5 cm)
M. Cabinet door or hinges should not extend into the cutout.
N. Remaining counter depth should not exceed 2¼" (5.7 cm).
B
C
A
E
F
H
I
G
L
K
J
A. 18" (45.7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE*.
E. 30" (76.2 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of range to side wall or
other combustible material
G. The shaded area is recommended for installation of rigid gas pipe
and grounded outlet.
" (33.3 cm)
¹⁄₈
H. 13
I. 7
" (19.5 cm)
¹¹⁄₁₆
¹³⁄₁₆
" (12.2 cm)
J. 4
" (9.4 cm)
¹¹⁄₁₆
K. 3
L. 12" (30.5 cm)
M. Cabinet door or hinges should not extend into the cutout.
D
M
*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is shielded by not less than ¼" (6.35 mm) ame retardant
millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020"
(0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.
6
Electrical Requirements
Gas Supply Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
IMPORTANT: The range must be electrically grounded in
accordance with local codes and ordinances, or in the absence
of local codes, with the National Electrical Code, ANSI/NFPA 70
or Canadian Electrical Code, CSA C22.1.
This range is equipped with an electronic ignition system that will
not operate properly if plugged into an outlet that is not properly
polarized.
If codes permit and a separate ground wire is used, it is
recommended that a qualied electrical installer determine that
the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
■ A 120-volt, 60 Hz., AC only, 15-amp fused, ground and
polarized electrical circuit is required. A time-delay fuse or
circuit breaker is also recommended. It is recommended that
a separate circuit serving only this range be provided.
■ Electronic ignition systems operate within wide voltage limits,
but proper grounding and polarity are necessary. Check that
the outlet provides 120-volt power and is correctly grounded.
■ This gas range is not required to be plugged into a GFCI
(Ground-Fault Circuit Interrupter) outlet. It is recommended
that you not plug an electric spark ignition gas range or any
other major appliance into a GFCI wall outlet as it may cause
the GFCI to trip during normal cycling.
■ Performance of this range will not be affected if operated
on a GFCI-protected circuit. However, occasional nuisance
tripping of the GFCI breaker is possible due to the normal
operating nature of electronic gas ranges.
■ The tech sheet and wiring diagram are located on the back
of the range in a plastic bag.
NOTE: The metal chassis of the range must be grounded in
order for the control panel to work. If the metal chassis of the
range is not grounded, no keypads will operate. Check with
a qualied electrician if you are in doubt as to whether the
metal chassis of the range is grounded.
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas
Code ANSI Z223.1 - latest edition or CAN/CGA B149 -
latest edition.
IMPORTANT: Leak testing of the range must be conducted
according to the manufacturer’s instructions.
Type of Gas
Natural Gas:
■ This range is factory set for use with Natural gas. See “Gas
Conversions” section. The model/serial/rating plate located
on the oven frame behind the top right-hand side of the oven
door has information on the types of gas that can be used. If
the types of gas listed do not include the type of gas available,
check with the local gas supplier.
Propane Gas Conversion:
Conversion must be done by a qualied service technician.
No attempt shall be made to convert the appliance from the gas
specied on the model/serial/rating plate for use with a different
gas without consulting the serving gas supplier. See “Gas
Conversions” section.
Gas Supply Line
■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the
range location. A smaller size pipe on longer runs may
result in insufcient gas supply. With propane gas, piping or
tubing size can be ½" (1.3 cm) minimum. Usually, propane
gas suppliers determine the size and materials used in the
system.
NOTE: Pipe-joint compounds that resist the action of
propane gas must be used. Do not use TEFLON®† tape.
†®TEFLON is a registered trademark of Chemours.
7
Flexible Metal Appliance Connector:
A
C
■ If local codes permit, a new CSA design-certied, 4 to 5
ft (122 to 152.4 cm) long, ½" or ¾" (1.3 or 1.9 cm) I.D.
(inside diameter), exible metal appliance connector may
be used for connecting range to the gas supply line.
■ A ½" (1.3 cm) male pipe thread is needed for connection
to the female pipe threads of the inlet to the appliance
pressure regulator.
■ Do not kink or damage the exible metal tubing when
moving the range.
■ Must include a shut-off valve:
Install a manual gas line shut-off valve in an easily accessible
location. Do not block access to shut-off valve. The valve is
for turning on or shutting off gas to the range.
B
A. Gas supply line
B. Shut-off valve “open” position
C. To range
Gas Pressure Regulator
The gas pressure regulator supplied with this range must be
used. The inlet pressure to the regulator should be as follows
for proper operation:
Natural Gas:
Minimum pressure: 5" (12.7 cm) WCP
Maximum pressure: 14" (35.5 cm) WCP
Propane Gas:
Minimum pressure: 11" (28 cm) WCP
Maximum pressure: 14" (35.5 cm) WCP
Contact local gas supplier if you are not sure about the inlet
pressure.
Burner Input Requirements
Input ratings shown on the model/serial/rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced at
a rate of 4% for each 1,000 ft (304.8 m) above sea level (not
applicable for Canada).
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least 1"
water column pressure above the manifold pressure shown on
the model/serial/rating plate.
Line pressure testing above ½ psi (3.5 kPa)
gauge (14” [35.5 cm] WCP)
The range and its individual shut-off valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of ½ psi (3.5 kPa).
Line pressure testing at ½ psi (3.5 kPa)
gauge (14” [35.5 cm] WCP) or lower
The range must be isolated from the gas supply piping
system by closing its individual manual shut-off valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than ½ psi (3.5 kPa).
8
INSTALLATION INSTRUCTIONS
Unpack Range
WARNING
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
1. Remove shipping materials, tape and lm from the range.
Keep cardboard bottom under range. Do not dispose of
anything until the installation is complete.
2. Remove oven racks and parts package from oven and
shipping materials.
3. To remove cardboard bottom, rst take 4 cardboard
corners from the carton. Stack one cardboard corner on
top of another. Repeat with the other 2 corners. Place them
lengthwise on the oor behind the range to support the
range when it is laid on its back.
4. Using 2 or more people, rmly grasp the range and gently
lay it on its back on the cardboard corners.
5. Remove cardboard bottom.
The leveling legs can be adjusted while the range is on its back.
See the “Adjust Leveling Legs” section.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard on the oor in front of range to
protect the ooring. Using 2 or more people, stand range back
up onto the cardboard or hardboard.
Install Anti-Tip Bracket
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
1. Remove the anti-tip bracket from the inside of the oven.
2. Determine which mounting method to use: oor or wall.
If you have a stone or masonry oor, you can use the wall
mounting method. If you are installing the range in a mobile
home, you must secure the range to the oor.
This anti-tip bracket and screws can be used with wood
or metal studs.
3. Determine and mark centerline of the cutout space. The
mounting bracket can be installed on either the left-hand or
right-hand side of the cutout. Position mounting bracket
against the wall in the cutout so that the V-notch of the
bracket is 12½" (31.8 cm) from centerline, as shown.
Centerline
A. 12½" (31.8 cm)
B. Bracket V-notch
B
A
9
4. Drill two 1/8” (3 mm) holes that correspond to the bracket
holes of the determined mounting method. See the following
illustrations.
Floor Mounting
Rear position
Front position
Diagonal (2 options)
Wall Mounting
5. Using the two #10 x 15/8" (4.1 cm) Phillips-head screws
provided, mount anti-tip bracket to the wall or oor.
6. Move range close enough to opening to allow for nal
electrical connections. Remove shipping base, cardboard,
or hardboard from under range.
7. Move range into its nal location, making sure rear leveling
leg slides into anti-tip bracket.
Adjust Leveling Legs
1. If range height adjustment is necessary, use a wrench
or pliers to loosen the 4 leveling legs.
This may be done with the range on its back or with the
range supported on 2 legs after the range has been placed
back to a standing position.
NOTE: To place range back up into a standing position, put
a sheet of cardboard or hardboard in front of range. Using 2
or more people, stand range back up onto the cardboard or
hardboard.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
8. Move range forward onto shipping base, cardboard, or
hardboard to continue installing the range, using the
following installation instructions.
2. Measure the distance from the top of the counter to the oor.
3. Measure the distance from the top of the cooktop to the
bottom of the leveling legs. This distance should be the
same. If it is not, adjust the leveling legs to the correct
height. The leveling legs can be loosened to add up to
a maximum of 1" (2.5 cm). A minimum of 3/16" (5 mm) is
needed to engage the anti-tip bracket.
NOTE: If height adjustment is made when range is standing,
tilt the range back to adjust the front legs, and then tilt
forward to adjust the rear legs.
4. When the range is at the correct height, check that there is
adequate clearance under the range for the anti-tip bracket.
Before sliding range into its nal location, check that the
antitip bracket will slide under the range and onto the rear
leveling leg prior to anti-tip bracket installation.
NOTE: If a Trim Kit will be used, the top of the cooktop
should be higher than the counter. See the Installation
Instructions included with the Trim Kit for the correct height.
10
Level Range
A
FG
A
A
B
1. Place level on the oven bottom, as indicated in one of
the two gures below, depending on the size of the level.
Check with the level side to side and front to back.
2. If range is not level, use a wrench or pliers to adjust leveling
legs up or down until the range is level.
NOTE: Range must be level for satisfactory baking
performance and best cleaning results using AquaLift® SelfClean Technology.
Make Gas Connection
WARNING
3. Use a 15/16" (2.4 cm) combination wrench and an adjustable
wrench to attach the exible connector to the adapters.
IMPORTANT: All connections must be wrench-tightened. Do
not make connections to the gas regulator too tight. Making
the connections too tight may crack the regulator and cause
a gas leak. Do not allow the regulator to turn when tightening
ttings.
B
C
A. Gas pressure regulator
B. Use pipe-joint compound.
C. Adapter (must have ½"
[1.3 cm] male pipe thread)
D. Flexible connector
D
E
H
E. Manual gas shut-off valve
F. ½" (1.3 cm) or ¾" (1.9 cm)
gas pipe
G. Use pipe-joint compound.
H. Adapter
Complete Connection
1. Check that the gas pressure regulator shut-off valve is in
the “on” position.
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
This range is factory-set for use with Natural gas. To use this
range with propane gas, see the “Gas Conversions” section
before connecting this range to the gas supply. Gas conversions
from Natural gas to propane gas or from propane gas to Natural
gas must be done by a qualied installer.
Typical Flexible Connection
1. Apply pipe-joint compound made for use with propane gas
to the smaller thread ends of the exible connector adapters.
See B and G in the following illustration.
2. Attach one adapter to the gas pressure regulator and
the other adapter to the gas shut-off valve. Tighten both
adapters, being certain not to move or turn the gas
pressure regulator.
A. Gas pressure regulator shut-off
valve shown in the “on” position
2. Open the manual shut-off valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
A. Closed valve
B. Open valve
3. Test all connections by brushing on an approved
noncorrosive leak-detection solution. If bubbles appear,
a leak is indicated. Correct any leak found.
11
4. Remove cooktop burner caps and bases from package
D
A
For Models KSGG700E and KSGB900E:
For Model JGS1450D:
B. X-Large
E. Large
Small capMedium cap Large capX-Large cap
containing parts. Place the burner bases as indicated by the
following illustration for your model:
For Models MGS8880D, WEG730H0D, and WEG760H0D:
A
D
5. Align the gas tube opening in the burner base with the
orice holder on the cooktop and the igniter electrode
with the notch in the burner base.
A
B
C
A. Small
B. Large
C. MediumD.Medium
A
A. Small
B. X-Large
C. MediumD.Medium
C
E
EB
D. Igniter electrode
E. Orice holder
E. Large
A. Burner cap
B. Gas tube opening
C. Burner base
6. Place the burner caps on the appropriate burner bases.
IMPORTANT: The bottom of the small and medium caps are
different. Do not put the wrong size burner cap on the burner
base.
D
C
Burner caps should be level when properly positioned. If
burner caps are not properly positioned, surface burners
willnot light. The burner cap should not rock or wobble when
EB
E. Large
properly aligned.
12
A
A. Small
C
C. OvalD. Medium
B
D
A. Incorrect
B. Correct
WARNING
EB
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
7. Plug into a grounded 3 prong outlet.
Verify Anti-Tip Bracket Is Installed
and Engaged
On Ranges Equipped with a Premium Storage Drawer:
1. Slide range into nal location, making sure rear leveling leg
slides into anti-tip bracket.
2. Remove the premium storage drawer. See the “Remove/
Replace Drawer” section.
3. 3. Use a ashlight to look underneath the bottom of the
range.
4. Visually check that the rear range foot is inserted into the slot
of the anti-tip bracket.
On Ranges Equipped with a Warming Drawer or Baking
Drawer:
1. Slide range into nal location, making sure rear leveling leg
slides into anti-tip bracket. Leave a 1" (2.5 cm) gap between
the back of the range and the back wall.
2. Place the outside of your foot against the bottom front of the
warming drawer or baking drawer to keep the range from
moving, and then grasp the back of the range, as shown.
3. Slowly attempt to tilt the range forward.
If you encounter immediate resistance, the range foot is
engaged in the anti-tip bracket. Go to Step 8.
4. If the rear of the range lifts more than ½" (1.3 cm) off the oor
without resistance, stop tilting the range and lower it gently
back to the oor. The range foot is not engaged in the antitip bracket.
IMPORTANT: If there is a snapping or popping sound when
lifting the range, the range may not be fully engaged in the
bracket. Check to see if there are obstructions keeping
the range from sliding to the wall or keeping the range foot
from sliding into the bracket. Verify that the bracket is held
securely in place by the mounting screws.
5. Slide the range forward, and verify that the anti-tip bracket is
securely attached to the oor or wall.
6. Slide range back so the rear range foot is inserted into the
slot of the anti-tip bracket.
7. Repeat steps 1 and 2 to ensure that the range foot is
engaged in the anti-tip bracket.
If the rear of the range lifts more than ½" (1.3 cm) off the oor
without resistance, the anti-tip bracket may not be installed
correctly. Do not operate the range without anti-tip bracket
installed and engaged. Please reference the “Warranty”
section of the User Guide to contact service.
8. Move the range into its nal location. Check that the range
is level by placing a level on the oven bottom. See the “Level
Range” section. IMPORTANT: If the range is moved to adjust
the leveling legs, verify that the anti-tip bracket is engaged
by repeating steps 1 to 8.
Electronic Ignition System
Initial Lighting and Gas Flame Adjustments
Cooktop and oven burners use electronic igniters in place of
standing pilots. When the cooktop control knob is turned to the
“ignite” position, the system creates a spark to light the burner.
All cooktop burners will spark, but only the burner with the
control knob turned to the “ignite” position will produce a ame.
This sparking continues as long as the control knob is turned to
the “ignite” position.
When the oven control is turned to the desired setting, sparking
occurs and ignites the gas.
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the “ignite” position.
The ame should light within 4 seconds. The rst time a burner
is lit, it may take longer than 4 seconds to light because of air in
the gas line.
If Burners Do Not Light Properly:
■ Turn cooktop control knob to the "off" position.
■ Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
■ Check that the gas shut-off valves are set to the open position.
■ Check that burner caps are properly positioned on burner
bases.
Repeat start-up. If a burner does not light at this point, turn the
control knobs to the "off" position and contact your dealer or
authorized service company for assistance. Please reference the
“Warranty” section of the User Guide to contact service.
If the cooktop "low" burner ame needs to be adjusted for any
of the burners, see the “Adjust Flame Height” section.
Check Operation of Oven Bake Burner
1. Press BAKE.
2. Press the Start pad.
The oven burner should light within 8 seconds. The rst
time a burner is lit, it may take longer than 8 seconds to
light because of air in the gas line.
3. After 2 minutes, open the oven door and check that the
oven is warm.
If Burner Does Not Light Properly:
■ Press the Off pad.
■ Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
■ Check that the gas shut-off valves are set to the open
position.
13
Repeat steps 1 to 3. If the burner does not light at this point,
C. Drawer glide notch
B
B. Drawer glide notch
press the off pad and contact your dealer or authorized service
company for assistance. Please reference the “Warranty” section
of the User Guide to contact service.
If the bake burner ame needs to be adjusted, see the “Adjust
Flame Height” section.
Refer to the User Guide for proper operation of the oven controls.
To Replace:
1. Align the forward drawer notches with the notches in the
drawer glides on both sides. Place the rear alignment tabs
into the drawer glides on both sides.
Check Operation of Oven Broil Burner
1. Close the oven door.
2. Press BROIL.
3. Press the Start pad.
The oven burner should light within 8 seconds. The rst time
a burner is lit, it may take longer than 8 seconds to light
because of air in the gas line.
4. After 2 minutes, open the oven door and check that the oven
is warm.
If Burner Does Not Light Properly:
■ Press the Off pad.
■ Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
■ Check that the gas shut-off valves are set to the open position.
Repeat steps 1 to 3. If the burner does not light at this point,
press the Off pad and contact your dealer or authorized service
company for assistance. Please reference the “Warranty” section
of the User Guide to contact service.
If the broil burner ame needs to be adjusted, see the “Adjust
Flame Height” section.
Refer to the User Guide for proper operation of the oven controls.
Remove/Replace Drawer
(on some models)
Remove all items from inside the baking drawer, warming drawer
or premium storage drawer, and then allow the range to cool
completely before attempting to remove the drawer.
To Remove:
1. Open the drawer to its fully open position.
2. Using a at-blade screwdriver, gently loosen the drawer
from the glide alignment notch, and then lift up the drawer
alignment tab from the glide.
A
A
B
A. Drawer alignment tab
2. Push the drawer in all the way.
3. Gently open and close the drawer to ensure it is seated
properly on the glides on both sides.
Oven Door
For normal range use, it is not suggested to remove the oven
door. However, if removal is necessary, make sure the oven is OFF
and cool. Then, follow these instructions. The oven door is heavy.
To Remove:
1. Open oven door all the way.
2. Pinch the hinge latch between two ngers and pull forward.
Repeat on other side of oven door.
A
A. Hinge latch
C
A. Flat-blade screwdriver
B. Drawer alignment tab
3. Repeat Step 2 on the other side. The drawer is no longer
attached to the drawer glides. Using both hands, pick up
the drawer to complete the removal.
14
3. Close the oven door as far as it will shut.
4. Lift the oven door while holding both sides.
Continue to push the oven door closed and pull it away
from the oven door frame.
To Replace:
1. Insert both hanger arms into the door. Be sure that the
hinge notches are engaged in the oven door frame.
A
A. Hinge notch
2. Open the oven door.
The door should be able to open all the way.
3. Move the hinge levers back to the “locked” position.
Check that the door is free to open and close and is level
while closed. If it is not, repeat the removal and installation
procedures.
Complete Installation
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Check that you have all of the range accessories, especially
oven racks. These accessories may be in the range
packaging.
4. Dispose of/recycle all packaging materials.
5. Check that the range is level. See the “Level Range” section.
6. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by shipping material.
Dry thoroughly with a soft cloth. For more information, see
the “Range Care” section of the User Guide.
7. Read the User Guide.
8. Turn on surface burners and oven. See the User Guide
for specic instructions on range operation.
NOTE: Odors and smoke are normal when the oven is used
the rst few times.
If Range Does Not Operate, Check the Following:
■ Household fuse is intact and tight, or circuit breaker has
not tripped.
■ Gas pressure regulator shut-off valve is in the “open” position.
■ Range is plugged into a grounded 3 prong outlet.
■ Electrical supply is connected.
9. When the range has been ON for 5 minutes, check for heat.
If the range is cold, turn off the range and check that the gas
supply line shut-off valve is open.
■ If the gas supply line shut-off valve is closed, open it,
and then repeat the 5-minute test as outlined above.
■ If the gas supply line shut-off valve is open, close it,
and contact a qualied technician.
If You Need Assistance or Service:
Please reference the “Warranty” section of the User Guide
to contact service.
15
Loading...