JENN-AIR JGRP436HM, JGRP536HM, JGRP636HM, JGRP436HL, JGRP536HL Installation Instructions

...

INSTALLATION INSTRUCTIONS

CommerCial-Style GaS ConveCtion ranGeS

30"(76.2Cm),36"(91.4Cm),and48" (121.9 Cm)

INSTRUCTIONS D’INSTALLATION

CuiSinière à Gaz à ConveCtion de Style CommerCial

de30po(76,2Cm),36po (91,4Cm) et48po (121,9Cm)

Pour utilisation résidentielle uniquement

INSTRUCCIONES DE INSTALACIÓN

eStufaS de ConveCCión a GaS eStilo ComerCial de

30"(76,2Cm),36"(91,4Cm)y 48" (121,9Cm)

Table of Contents/Table des matières/Tabla de contenidos

RANGE SAFETY ..............................................2

INSTALLATION REQUIREMENTS ................4

Tools and Parts .............................................4

Location Requirements ................................6

Electrical Requirements ...............................8

Gas Supply Requirements ...........................8

INSTALLATION INSTRUCTIONS ................10

Unpack the Range ......................................10

Remove Door ..............................................11

Install Anti-Tip Bracket ...............................12

Make Gas Connection ...............................13

Verify Anti-Tip Bracket Location ................13

Level Range ................................................14

Install Griddle Tray ......................................14

Electronic Ignition System ..........................14

Install Kick Plate .........................................15

Complete Installation ..................................15

GAS CONVERSIONS ....................................16

Propane Gas Conversion ...........................16

Natural Gas Conversion .............................26

For residential use only

Solo para uso residencial

SÉCURITÉ DE LA CUISINIÈRE ...................37

EXIGENCES D’INSTALLATION ...................39

Outils et pièces ...........................................39

Exigences d’emplacement.........................41

Spécications électriques ..........................43

Spécications de l’alimentationen gaz .....43

INSTRUCTIONS D’INSTALLATION .............45

Déballage de la cuisinière ..........................45

Retirer la porte ............................................46

Installation de la bride antibasculement ....47

Raccordement au gaz ................................48

Vérication de l’emplacement dela bride

antibasculement .........................................48

Ajustement de l’aplomb de la cuisinière ....49

Installer le plateau d’égouttement .............49

Système d’allumage électronique .............49

Installer la plinthe ........................................50

Terminer l’installation ..................................50

CONVERSIONS POUR CHANGEMENT DE

GAZ .................................................................51

Conversion pour l’alimentation aupropane ..51

Conversion au gaz naturel .........................61

SEGURIDAD DE LA ESTUFA ......................72

REQUISITOS DE INSTALACIÓN .................74

Herramientas y piezas ................................74

Requisitos de ubicación .............................76

Requisitos eléctricos ..................................78

Requisitos del suministro de gas ...............78

INSTRUCCIONES DE INSTALACIÓN .........80

Desembale la estufa ...................................80

Quite la puerta ............................................81

Instalación del soporte antivuelco .............82

Conexión del suministro de gas ................83

Vericación de la ubicación del soporte

antivuelco ....................................................83

Nivelación de la estufa ...............................84

Instale la bandeja de la plancha ................84

Sistema de encendido electrónico ............84

Instale la placa de protección ....................85

Finalización de la instalación .....................85

CONVERSIONES DE GAS ...........................86

Conversión a gas propano .........................86

Conversión a gas natural ...........................96

IMPORTANT:

Save for local electrical inspector’s use.

Installer: Leave installation instructions with the homeowner. Homeowner: Keep installation instructions for future reference.

IMPORTANT:

Conserver ces instructions à l’usage de l’inspecteur des installations électriques local.

Installateur: Remettre les instructions d’installation au propriétaire.

Propriétaire: Conserver les instructions d’installation pour référence ultérieure.

W11521193A www.jennair.com (U.S.A.) www.jennair.ca (Canada)

IMPORTANTE:

Guarde para tener a disposición del inspector de electricidad local.

Instalador: Déjele las instrucciones de instalación al propietario. Propietario: Guarde las instrucciones de instalación para futuras

consultas.

RANGE SAFETY

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

•

Do not touch any electrical switch.

•

Do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

•

instructions. If you cannot reach your gas supplier, call the fire department.

•

– Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the “What to do if you smell gas” instructions.

IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or unintended operation.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by

the State of Massachusetts.

■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage the anti-tip bracket if the range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

Anti-Tip Bracket

Range Foot

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

Slide range back so rear range foot is under anti-tip bracket.•

• See installation instructions for details.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

Pipe wrench Adjustable wrench or

5/8"(16mm) wrench

Drill 3/8" (9.5 mm) drive ratchet 15/16" (24 mm)

Level Tubing cutter 1/4" (6.4 mm), 3/8" (9.5 mm),

3/16" (4.8 mm) carbide tip

masonry bit

1/8" (3.2 mm) drill bit Pipe‑joint compound

resistanttoPropanegas

1/8" x 41/4" (3mmx100mm)

at‑blade screwdriver

combinationwrench

5/16" (7.9 mm) nut drivers

Noncorrosive leak‑detection

solution

#2 Phillips screwdriver

Pliers

Marker or pencil

Tape measure

For Propane/Natural Gas Conversions

Large at‑blade screwdriver Adjustable wrench T20® Torx®† Driver Masking tape

1/2" (1.3 cm) open end

wrench

†®TORX and T20 are trademarks of Acument Intellectual Properties, LLC.

#1 Square Driver

Parts Supplied

Check that all parts are included.

■ Anti-tip bracket kit

Parts Needed

■ All models must be installed with a backguard if installing

at zero clearance to a combustible back wall surface such as drywall. Alternatively, zero clearance to a back wall is acceptable provided the surface of the entire back wall above the range and below the hood is covered with a non-combustible material such as tile or stainless steel. See “Cabinet Dimensions” in the “Location Requirements” section for installation requirements.

Check local codes and consult gas supplier. Check existing gas



supply and electrical supply. See the “Electrical Requirements” and “Gas Supply Requirements” sections.

It is recommended that all electrical connections be made by alicensed, qualied electrical installer.

A. Anti-tip bracket B. #8-18 x 1" (2.5cm) Phillips head screws (4)

NOTE: Anti-tip bracket must be securely mounted to suboor. Thickness of ooring may require longer screws toanchor bracket to suboor. Longer screws are available from your local hardware store. See the “Install Anti-Tip Bracket” section.

■ Burner grates

■ Burner caps

■ Griddle drip tray (on griddle models)

High Altitude Conversion

Reoricing of this range/rangetop is not required for proper operation. Low burner rates may require resetting for best results.

Refer to the “Adjusting Simmer Low and Main Low Settings

on Surface Burner for Propane” section (page 18) for

Propane Gas Operation. Refer to the “Adjusting Simmer Low and Main Low Settings

on Surface Burner for Natural Gas” section (page 28) for

Natural Gas Operation.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Donot obstruct ow of combustion and ventilation air.

■ It is the installer’s responsibility to comply with installation

clearances specied on the model/serial/rating plate. The model/serial/rating plate is located under the console on theright-hand side.

■ It is recommended that a 585 CFM (993.9 m

range hood beinstalled above the range.

■ Follow the range hood or microwave hood combination

installation instructions for dimensional clearances above the cooktop surface.

■ Recessed installations must provide complete enclosure

ofthe sides and rear of the range.

■ All openings in the wall or oor where range is to be installed

must be sealed.

■ Do not seal the range to the side cabinets.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see the “Install Anti-Tip Bracket” section.

■ Grounded electrical supply is required. See the “Electrical

Requirements” section.

■ Proper gas supply connection must be available. See the

“Gas Supply Requirements” section.

■ Contact a qualied oor covering installer to check that

the oor covering can withstand at least 200°F (93°C). Use an insulated pad or 1/4" (6.4 cm) plywood over carpet and under range if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate, or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home ‑ Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title24CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280).When such standard is not applicable, use the Standard forManufactured Home Installations, ANSI A225.1/NFPA 501A or local codes.

In Canada, the installation of this cooktop must conform with thecurrent standards CAN/CSA-A240-latest edition or with localcodes.

/hr) or larger

Product Dimensions

NOTE: Cooktop features may differ. 30" (76.2 cm) models

A. 273/4" (70.5 cm) depth with control panel (See NOTE) B. 353/4" (90.8 cm) range height when sitting on the wheels C. 297/8 " (75.7 cm) width D. Model/serial/rating plate location/SAID label

36" (91.4 cm) models

Mobile Home Installations Require:

■ When this range is installed in a mobile home, it must be

secured to the oor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

A. 271⁄8" (68.9 cm) depth with control panel (See NOTE) B. 353⁄4" (90.8 cm) range height when sitting on the wheels C. 36" (91.4 cm) width D. Model/serial/rating plate location/SAID label

48" (121.9 cm) models

Electrical installation area*

installation

A. 271⁄8" (68.9 cm) depth with control panel (See NOTE.) B. 353⁄4" (90.8 cm) range height when sitting on the wheels C. 48" (121.9 cm) width D. Model/serial/rating plate location/SAID label

NOTE: When installed in a 24" (61.0 cm) base cabinet with 25" (63.5 cm) countertop; front of oven door protrudes 17/8" (4.8 cm) beyond 24" (61.0 cm) base cabinet.

Cabinet Requirements

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth, and 36"(91.4 cm) countertop height. Dimensions must be met inorder to ensure a ush t to back wall.

IMPORTANT: If installing a range hood, hood liner, or microwave hood combination above the cooking surface, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooking surface.

O***

Gas

area

A. 18" (45.7 cm) upper cabinet to countertop B. 30" (76.2 cm) model: 30" (76.2 cm) minmum upper cabinet width

36" (91.4 cm) model: 36" (91.4 cm) minmum upper cabinet width 48" (121.9 cm) model: 48" (121.9 cm) minmum upper cabinet

width C. 13" (33 cm) maximum upper cabinet depth D. For minimum clearance to top of range.**

E. 30" (76.2 cm) on 30" (76.2 cm) models

36" (91.4 cm) on 36" (91.4 cm) models

48" (121.9 cm) on 48" (121.9 cm) models F. 12" (30.4 cm) minmum clearance from both sides of range to

side wall orother combustible material G. 15" (38.1 cm) H. 22" (55.9 cm) on 30" (76.2 cm) models

28" (71.1 cm) on 36" (91.4 cm) models

40" (101.6 cm) on 48" (121.9 cm) models I. 4" (10.1 cm) J. 3" (7.6 cm) K. 5" (12.7 cm) L. 6" (15.2 cm) on 30" (76.2 cm) models

12" (30.5 cm) on 36" (91.4 cm) models

24" (61.0 cm) on 48" (121.9 cm) models M. 101/2" (26.7 cm) N. 9" (22.9 cm) O. 6" (15.2 cm)***

** If not using ventilation, Minimum Clearances 30" (76.2 cm) models: 42" (106.7 cm) minimum clearance

between the top of the cooking platform and the bottom of a combustible surface.

36" (91.4 cm) models: 42" (106.7 cm) minimum clearance

between the top of the cooking platform and the bottom of a combustible surface.

48" (121.9 cm) models: 48" (121.9 cm) minimum clearance

between the top of the cooking platform and the bottom of a combustible surface.

*** If the surface of the back wall is constructed of a combustible

material and a backguard is not installed, a 6" (15.2 cm) minimum clearance is required for all models.

Electrical Requirements

IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is recommended that a qualied electrical installer determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

■ A 120 V, 60 Hz, AC-only, 15 A, fused electrical circuit

is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided.

■ Electronic ignition systems operate within wide voltage limits,

but proper grounding and polarity are necessary. Check that the outlet provides 120 V power and is correctly grounded.

■ The wiring diagram is located behind the kick plate in a clear

plastic bag.

Gas Supply Requirements

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel, authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest edition.

IMPORTANT: Range must be connected to a regulated gassupply.

IMPORTANT: Leak testing of the range must be conducted according to the manufacturer’s instructions.

Type of Gas

Natural Gas:

This range is factory set for use with Natural gas. The model/serial/rating plate, located under the console on the right-hand side, has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

Propane Gas conversion:

Conversion must be done by a qualied service technician. No attempt shall be made to convert the range from the gas

specied on the model/serial/rating plate for use with a different gas without consulting the serving gas supplier. To convert to Propane gas, use the Propane gas conversion kit provided with your range and see the “Gas Conversions” section. The parts for this kit are in the package containing literature supplied with the range.

Gas Supply Line

Burner Input Rating — Altitude

■ Provide a gas supply line of 3/4" (1.9 cm) rigid pipe to the

range location. A smaller size pipe on longer runs may result in insufcient gas supply. With Propane gas, piping ortubing size can be 1/2" (1.3 cm) minimum. Usually, Propane gas suppliers determine the size and materials usedin the system.

NOTE: Pipe-joint compounds that resist the action of Propane gas must be used. Do not use TEFLON®† tape.

Flexible metal appliance connector:

■ If local codes permit, a new CSA design-certied,

4-5ft (122-152 cm) long, 5/8" (1.6 cm) or 3/4" (1.9 cm) I.D., exible metal appliance connector may be used for connecting the cooktop to the gas supply line.

■ A 1/2" (1.3 cm) male pipe thread is needed for

connection to the female pipe threads of the inlet totheappliance pressure regulator.

■ Do not kink or damage the exible metal tubing when

moving the range.

IMPORTANT: All connections must be wrench-tightened. Do not make connections to the gas regulator too tight. Making the connections too tight may crack the regulator and cause a gas leak. Do not allow the regulator to turn or move when tightening ttings.

■ Must include a shut-off valve:

Install a manual gas line shut-off valve in an easily accessible location. Do not block access to shut-off valve. The valve is for turning on or shutting off gas to the range.

Input ratings shown on the model/serial/rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings need to be reduced at a rate of 4% for each 1,000 ft (304.8 m) above sealevel (not applicable for Canada).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least 1" (2.5cm) water column pressure above the manifold pressure shown on the model/serial/rating plate.

Line pressure testing above 1/2 psi (3.5 kPa) gauge (14" [35.6cm]WCP)

The range and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2psi (3.5 kPa).

Line pressure testing at 1/2 psi (3.5 kPa) gauge (14" [35.6cm]WCP) or lower

The range must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).

A. Gas supply line B. Shut-off valve open position C. To range

Gas Pressure Regulator

The gas pressure regulator supplied with this cooktop must beused. The inlet pressure to the regulator should be as followsforproper operation:

Natural Gas:

Minimum pressure: 6" (15.2 cm) WCP Maximum pressure: 14" (35.6 cm) WCP

Propane Gas:

Minimum pressure: 11" (27.9 cm) WCP Maximum pressure: 14" (35.6 cm) WCP Contact local gas supplier if you are not sure about the

inletpressure.

†®TEFLON is a registered trademark of Chemours.

INSTALLATION INSTRUCTIONS

WARNING

Unpack the Range

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

Remove shipping materials, tape, and lm from range. Keepshipping pallet under range. Remove oven racks, and parts package from inside oven. Remove grates from top of oven.

Remove Kick Plate

1. Your range will have the kick plate packaged on top of the

unit. a. Remove kick plate from top of range and grate pack.

In packaging

2. For 48" (121.9 cm) models only, rotate center support

counterclockwise off the pallet until it stops.

NOTE: This support is used only for shipping and is not needed for installation.

3. Lay a piece of cardboard from side packaging on the oor

behind range. Using two or more people, rmly grasp each side of range. Lift range up about 3" (8.0 cm) and move it back until range is off shipping pallet. Set range on cardboard to avoid damaging oor.

A. Kick plate

Packaging removed

A. Kick plate

b. Lay kick plate to the side to avoid scratching.

Remove Door

Door Removal

■ Do not remove the side door spacers until the range is ready

to install. Removing the door spacers could allow the door to shift, damaging the door latch.

■ Do not lift or move the range by the door handle(s) or control

panel.

■ Prior to installing the range, you will need to remove the oven

door(s). Prepare a surface where you will place the door(s). This surface should be at and covered with a soft blanket, or use the corner posts from the packaging material.

Use two hands to remove and replace

the oven door(s). It may be necessary to gently shift door from side to side.

A. Oven door hinge in the locked position

B. Oven door hinge in the

unlocked position

Partially close the door to engage the door latch locks. The door will stop at this point.

A. Slot in the oven frame for the

door hinge lock

Replace the Door

■ To replace the oven door(s), locate the slots in the oven

cavity for the hinge locks and repeat the steps above in reverse order. Make sure the door closes properly and there is no interference from the door latch. If necessary, remove the door and repeat the steps above. If power is connected to the range, open and close the door to make sure the oven light comes on and goes off appropriately.

■ The range is equipped with leveling legs and rollers. Once

the range is removed from the shipping pallet, make sure the leveling legs are not touching the oor and use the rollers to move the range into position. Always cover the ooring surface to avoid damage to the oor. Do not roll the range directly on the oor.

Install Anti-Tip Bracket

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

3. Drill two 1/8" (3.0 mm) holes that correspond to the bracket

holes of the determined mounting method. See the following illustrations.

Floor Mounting

A. #12 x 15⁄8" (4.1 cm) screws B. Anti-tip bracket

Wall Mounting

1. Determine which mounting method to use: oor or wall.

If you have a stone or masonry oor, you can use the wallmounting method.

2. Determine and mark centerline of the cutout space. The

mounting bracket must be installed on the left side of the cutout. Position mounting bracket in cutout as shown in the following illustration.

Measurement B:

30" (76.2 cm) ranges: 13" (33.0 cm) 36" (91.4 cm) ranges: 16" (40.6 cm) 48" (121.9 cm) ranges: 22" (55.9 cm)

Measurement C:

Optional distance from back wall. If back wall is constructed of a combustible material and a backguard is not installed, a 6" (15.2 cm) minimum clearance is required for all models. Install anti-tip bracket accordingly.

A. #12 x 15⁄8" (4.1 cm) screws B. Anti-tip bracket

4. Using a Phillips screwdriver, mount anti-tip bracket

tothewall or oor with the two #12 x 15⁄8" (4.1 cm) screwsprovided.

Depending on the thickness of your ooring, longer screws may be necessary to anchor the bracket to the suboor. Longer screws are available from your local hardware store.

5. Move range close enough to opening to allow for electrical

connections to be made. Remove shipping base, cardboard, or hardboard from under range.

6. Continue installing your range using the following

installationinstructions.

A. Centerline B. Centerline of cutout to outside

edge of anti-tip bracket

C. Back wall to back of range

Make Gas Connection

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel, authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

1. Assemble exible connector from gas supply pipe to

pressure regulator located in the middle rear of the range.

2. Apply pipe-joint compound made for use with Propane gas

to the smaller thread ends of the exible connector adapters. (SeeB and G in the following illustration.)

3. Attach one adapter to the gas pressure regulator and

the other adapter to the gas shut-off valve. Tighten both adapters, being certain not to move or turn the gas pressure regulator.

4. Use a 15/16" (2.4 cm) combination wrench and an adjustable

wrench to attach the exible gas supply to the adapters. Check that connector is not kinked.

IMPORTANT: All connections must be wrench-tightened. Donotmake connections to the gas regulator too tight. Making the connections too tight may crack the regulator and cause a gas leak. Do not allow the regulator to turn or move when tightening ttings.

Complete Connection

1. Open the manual shut-off valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

A. Closed valve B. Open valve

2. Test all connections by brushing on an approved

noncorrosive leak-detection solution. If bubbles appear,aleak is indicated. Correct any leak found.

3. Remove range burner caps, and grates from parts package.

Place burner caps on burner bases. Place grates over burners andcaps.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

4. Plug into a grounded 3 prong outlet.

5. Turn on power supply. For further information, please refer

tothe user instructions located in the Use and Care Guide.

Verify Anti-Tip Bracket Location

1. Using a 5/16" (7.9 mm) socket or wrench, turn all four

leveling rods one full turn to raise the range and provide enough clearance for the rear leveling leg to slide into the anti-tip bracket.



A. Gas pressure regulator B. Use pipe-joint compound. C. Adapter (must have 1/2"

[1.3cm] male pipe thread)

D. Flexible connector

E. Manual gas shut-off valve F. 1/2" (1.3 cm) or

3/4"(1.9cm) gas pipe G. Use pipe-joint compound. H. Adapter

2. Move range into its nal location, making sure rear leveling

leg slides into anti-tip bracket.

3. Use a ashlight to look underneath the bottom of the range

and visually check that the rear range foot is inserted into theslot of the anti-tip bracket.

Level Range

NOTE: Range must be level for satisfactory baking performance.

1. Place rack in oven.

2. Place level on rack and check levelness of the range, rst

side to side, then front to back.

3. If range is not level, adjust the leveling rods. Using a wrench,

turn leveling rods located behind the kick plate to level range and to raise or lower range to the desired countertop height. Leveling rods can be adjusted up to 11/2" (3.9 cm).

NOTE: All roller feet must be off the oor upon nal installation.

Electronic Ignition System

Install Burner Caps

Place burner caps on top of burner. If burner caps are not properly positioned, surfaceburners will not light.

Burner

A. Incorrect B. Correct

Initial Lighting and Gas Flame Adjustments

Range burners use electronic igniters in place of standing pilots. When the range control knob is turned to any position, the system creates a spark to light the burner. This sparking continues until the ame is lit or the knob is turned to OFF.

NOTE: The rst time igniting the burners will take longer. This allows the gas to reach the burners during the rst use.

A. Rear leveling rod B. Front leveling rod

NOTE: Turning clockwise raises the unit, whereas turning counterclockwise lowers the unit.

Install Griddle Tray

(On griddle models)

The griddle is factory installed.

1. Place drip tray in the well at the front of the griddle. Slide tray

toward the back until it stops.

Check Operation of Range Burners

Push in and turn each control knob to IGNITE. NOTE: You will hear a clicking sound while the line clears. The surface burners and grill ames should light within

4seconds. The rst time a burner is lit, it may take longer than4seconds to light because of air in the gas line.

After verifying the proper burner operation, turn the control knobs to OFF.

If burners do not light properly:

■ Turn range control knob to OFF.

■ Check that the range is plugged in and the circuit breaker

has not tripped or the fuse has not blown.

■ Check that the gas shut-off valves are set to the

open position.

■ Check that burner caps are properly positioned on burner

bases.

Repeat startup. If a burner does not light at this point, contact your dealer or authorized service company for assistance.

Flame Height

The range ame should be a steady blue ame. NOTE: Flame heights are factory set. If they don’t appear

correct, please contact your service provider.

Burner

A. Griddle drip tray B. Griddle

2. Clean griddle before using. Refer to the Use and Care Guide.

A. Upper (main) ame B. Lower (simmer) ame

Install Kick Plate

NOTE: Door must be removed in order to remove or replace kick plate. Refer to the “Remove Door” section.

Align kick plate over the kick plate slots and push kick plate down.

A. Kick plate B. Kick plate tab C. Kick plate slot

Complete Installation

1. Check that all parts are now installed. If there is an extra

part, go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. For oven use and cleaning, read the Use and Care Guide.

Check Operation of Oven(s)

1. Turn power on.

2. Start a Bake cycle. See the Use and Care Guide for

operating instructions.

If oven(s) does not operate, check the following:

■ Household fuse is intact and tight or circuit breaker hasnot

tripped.

■ Electrical supply is connected.

■ See the “Troubleshooting” section in the Use and Care

Guide.

3. When oven has been on for 10–15 minutes, open the oven

door and feel for heat. If you do not feel heat, turn off the oven and contact a

qualied technician.

If you need Assistance or Service:

Please reference the “Assistance or Service” section of the Useand Care Guide or contact the dealer from whom you purchased your range.

GAS CONVERSIONS

IMPORTANT: Gas conversions from Natural gas to Propane gas must be done by a qualied installer.

Propane Gas Conversion

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel, authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

1. Turn the manual shut-off valve to the closed position.

A. To range B. Shut-off valve (closed position) C. Gas supply line

2. Unplug range or disconnect power.

To Convert Gas Pressure Regulator from Natural Gas

to Propane

NOTE: Door must be removed in order to remove or replace kick

plate. Refer to the “Remove Door” section.

1. Lift the kick plate up and off of the kick plate tab.

5. Turn over the gas pressure regulator cap, and reinstall on the

regulator so that the hollow end faces out and the letters “LP” are visible.

A. Kick plate B. Kick plate tab C. Kick plate slot

2. Gently lay kick plate aside to avoid scratching.

3. Locate the gas pressure regulator at the left rear of the

range.

A. Gas pressure regulator

4. Remove the gas pressure regulator cap by using a

large at-blade screwdriver, turning the regulator cap counterclockwise.

NOTE: Do not remove the spring beneath the cap.

6. Tighten the gas pressure regulator cap by using a large

at-blade screwdriver, turning the regulator cap clockwise.

7. Test the gas pressure regulator and gas supply line.

The regulator must be checked at a minimum 1" (2.5 cm) water column above the set pressure. The inlet pressure to the regulator should be as follows for operation and checking the regulator setting:

Propane Gas:

Minimum pressure: 11" (27.9 cm) WCP Maximum pressure: 14" (35.6 cm) WCP

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least 1" (2.5 cm) water column pressure above the manifold pressure shown on the model/serial/rating plate.

Line pressure testing above 1/2 psi (3.5 kPa) gauge (14" [35.6cm] WCP)

The range and its individual shut-off valve must be disconnected from the gas supply piping system during anypressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).

Line pressure testing at 1/2 psi (3.5 kPa) gauge (14" [35.6cm]WCP) orlower

To Convert Surface Burners from Natural Gas to

Propane

Adjusting Simmer Low and Main Low Settings on Surface Burner for Propane

1. If the burner grates are installed, remove them.

2. Remove burner cap.

3. Remove the burner base by rst removing (2) T-20 screws.

Burner

A. Burner cap B. Screws C. Burner base

4. Apply masking tape to the end of a 1/4" (6.4 mm) nut driver

to help hold the gas orice spud in the nut driver while changing it. Insert nut driver into the gas opening and press down onto the gas orice spud and remove by turning the gas orice spud counterclockwise and lifting out. Set gas orice spud aside.

5. Replace with correct Propane gas orice spud. See the

“Propane Gas Orice Spud/Hood Chart”. Use the following chart to nd the exact orice spud placement.

Propane Gas Orice Spud/Hood Chart

Burner Rating

7,400 BTUs 70

13,000 BTUs 99

16,000 BTUs 116 1.16 mm Grill burner

NOTE: Refer to serial tag for more information on burner ratings and locations.

Stamp Size Burner Style

0.70 mm

0.44 mm

0.99 mm

0.50 mm

Small burner - main Small burner - simmer

Large burner – main Larger burner – simmer

Burner orice spud

1. Remove the surface burner control knobs and bezels (oven

control knobs and griddle control knobs do not have to be removed).

2. Locate the Simmer low-turndown adjustment screw through

the bezel on the left side of the ignition switch.

A B C

A. Simmer low-turndown adjustment screw B. Ignition switch C. Main low-turndown adjustment screw (inside stem)

3. With the burner ON, and set to Simmer Lo, adjust the

simmer ame down to the proper BTU level. Using a 1/8" x 4¼" (3.2 mm x 108 mm) at blade screwdriver, turn the simmer low-turndown adjustment screw clockwise until the ame height is below the bottom of the cap. If the ame becomes unstable and ickers or appears to race around the burner, the adjustment is too low and the screw should be adjusted counterclockwise until the ame is stable. Repeat this step for all surface burners, except the grill burner.

NOTE: Use a knob to adjust the burner valve. NOTE: If your range has the IR grill, then skip ahead to the

Convert IR Grill Burner section.

NOTE: Adjust each burner individually.

4. With burner OFF, using the same at blade screwdriver, turn

the main low-turndown adjustment screw 120-135 degrees clockwise. This will set the main low burner rate to a proper level.

5. Replace the bezels using the 2 screws which attach to the

valve brackets.

6. Push the surface knobs onto the valve stems.

7. Replace burner grates.

Flame Height

The cooktop ame should be a steady blue ame approximately 1/4" (6.4 mm) high.

Burner

A. Size stamp B. Fuel type stamp (L or N)

6. Place Natural gas orice in plastic parts bag for future use

and keep with package containing literature.

NOTE: There may be extra orices in your kit.

7. Replace the burner base and screws. Tighten screws only

until burner is snug to cooktop, do not over-tighten.

8. Replace burner cap.

9. Repeat steps 2 through 8 for the remaining burners.

A. Upper (main) ame B. Lower (simmer) ame

To Adjust Flame Height:

1. Unplug range or disconnect power.

2. Remove burner grates.

3. Remove the control knobs.

4. Open the oven door and remove the two screws on each

side of the range that hold the control console in place.

9. Use a 1/8" x 4¼" (3mmx100mm) at-blade screwdriver to

adjust the ame height. Tighten screw to reduce ame height. Loosen screw to increase ame height.

NOTE: Make sure to leave oven door open or the control console will not rest in the side brackets properly once it is detached.

5. Pull up on the control console and let it drop forward into the

notched console brackets on each side.

A. Control console bracket

6. Put a control knob onto the valve stem of the burner you

want to adjust.

A. Single ame burner adjustment screw (on right side of valve) B. Dual ame burner adjustment screw (on left side of valve)

10. When nished adjusting the ame height, put a control knob

back onto the valve stem and turn off the burner.

11. Remove the control knob.

12. Repeat steps 6 through 13 for any other burners that

need adjustment.

13. Lift up on the control console and set it back into place. For

a proper t, the ange of the control console must hook over the lip on the front of the range cooktop.

A. Control console ange B. Front lip of range cooktop

14. Check that the control console is ush with the top edge of

the range.

7. Turn the control knob to LO and, using a butane extension

lighter, light the burner.

8. Remove the control knob.

A. Flush with range top

15. Replace the two screws on each side of the control console.

16. Replace the control knobs.

17. Replace burner grates.

18. Test the ame by turning the control from LO to HI, checking

the ame at each setting.

To Convert IR Grill Burner for Propane

1. Unplug range or disconnect power.

2. Remove grill knob and bezel. The other surface knobs and

bezels should still be off the range.

3. Open the oven door and remove the two screws on each

side of the range that hold the control console in place.

NOTE: Make sure to leave oven door open or the control console will not rest in the side brackets properly once it is detached.

4. Pull up on the control console and let it drop forward into the

notched console brackets on each side.

6. Pull the grill orice holder out of the burner box far enough

away to allow access to the orice with a wrench, using caution not to kink the attached tubing.

A. Grill orice B. Grill orice holder

7. Using an adjustable wrench and a 1/2" (1.3 cm) open end

wrench remove the Natural (NG) gas orice spud and replace with the correct Propane (L) orice spud.

A. Control console bracket

5. Remove the two screws holding the grill orice holder

bracket.

A. Screws B. Grill orice holder bracket

Use 1/2" (1.3 cm) open end wrench to remove/replace orifice

Hold with adjustable wrench here

8. Reposition the grill orice holder assembly back into the

burner box, and replace the grill orice holder bracket and two holder screws.

9. Lift up on the control console and set it back into place. For

a proper t, the ange of the control console must hook over the lip on the front of the range cooktop.

NOTE: It may be necessary to lift valve stems to align with console holes.

A. Control console ange B. Front lip of range cooktop

10. Check that the control console is ush with the top edge of

the range.

A. Flush with range top

11. Replace the screws on each side of the control console.

12. Replace the control knobs and bezels.

13. Replace burner grates.

Convert Oven Bake Burner (30" [76.2 cm] and 36" [91.4 cm] models and the right oven cavity on 48" [121.9 cm] models)

4. Remove the oven bake burner screws and oven bake burner.

Rotate burner 90° to the left, and gently lay on its side.

D C

1. Slide the bake burner cover to the right or left.

A. Bake burner cover

2. Lift up and remove oven bake burner cover, and set aside.

3. Using a 1/4" (6.4 mm) nut driver, unscrew oven bafe nuts

and remove oven bafe. Set aside.

A. Oven bake burner screws B. Oven bake burner C. Oven bake burner electrode bracket D. Oven bake burner electrode

5. Lift up clip on the oven bake burner electrode bracket with a

nger or at-blade screwdriver, and pull away the electrode.

A. Oven bake burner electrode bracket B. Electrode bracket clip

A. Oven bafe B. Oven bafe nuts

6. Pull electrode out of bracket.

A. Grasp electrode here. B. Bracket

7. Apply masking tape to the end of a 1/4" (6.4 mm) nut driver

to help hold the gas orice spud in the nut driver while changing it. Insert nut driver into the gas opening, and press down onto the gas orice spud, then remove by turning the gas orice spud counterclockwise and lifting out. Set gas orice spud aside.

10. Push down on the clip on the electrode bracket.

A. Oven bake burner electrode bracket B. Electrode bracket clip

11. Replace oven bake burner electrode inside bracket.

A. Gas orice spud

8. Gas orice studs are stamped with a letter and a number.

Install the Number 125 oven bake burner orice spud.

9. Place Natural gas orice in plastic parts bag for future use,

and keep with package containing literature.

A. Oven bake burner electrode B. Oven bake burner electrode bracket

12. Reinstall the oven bake burner and oven bake burner

screws. See Step 4 for illustration.

13. Replace oven bafe and oven bafe nuts. The front holes will

be aligned, and a click will sound when bafe is seated.

Replace Oven Bake Burner Cover

1. Align notches on the oven bake burner cover with shoulder

screws in the bottom of the oven.

2. Pull the broil burner toward you until it slides out of the hole

in the oven back, and pull the electrode out of the bracket. The broil burner will hang down in the back of the oven while you change the orice.

A. Cover notches (4) B. Shoulder screws (4)

2. Lower cover, and slide to left or right to slide shoulder

screws into the narrow ends of the notches, then lock intoplace.

A. Bake burner cover

Convert Oven Broil Burner (30" [76.2 cm] and 36" [91.4 cm] models and the right oven cavity on 48" [121.9 cm] models)

A. Grasp electrode here. B. Bracket

Broil burner hanging

in back of oven

3. Apply masking tape to the end of a 1/4" (6.4 mm) nut driver

A. Oven back B. Broil burner orice C. Broil burner orice hole

4. Gas orice studs are stamped with a letter and a number.

Install the Number 90 oven broil burner orice spud.

5. Place Natural gas orice in plastic parts bag for future use,

and keep with package containing literature.

6. Replace the broil burner in the hole in the oven back with the

broil burner assembly inside the broil burner electrode hole as illustrated.

1. Using a 1/4" (6.4 mm) nut driver, remove broil burner screw.

Set aside with side igniter positioned on the right.

A. Broil burner screw B. Broil burner C. Broil burner orice hole

A. Broil burner orice hole B. Broil burner electrode C. Broil burner electrode hole

B C

7. Reinstall the oven broil burner screw. See Step 1 for

illustration. The screw is aligned with the hole when aclicksounds.

Convert Oven Bake Burner (left oven cavity on 48" [121.9 cm] models)

1. Remove oven racks. See the “Remove Racks” section.

2. Remove the oven door. See the “Remove Oven Door”

section.

3. Slide the bake burner cover to the right or left.

A. Bake burner cover

4. Lift up and remove oven bake burner cover, and set aside.

5. Remove the oven bake burner screws and oven bake burner,

and gently set aside.

6. Lift clip up on the oven bake burner electrode bracket

withanger or at-blade screwdriver.

A. Oven bake burner electrode bracket B. Electrode bracket clip

7. Pull electrode out of bracket.

A. Oven bake burner B. Oven bake burner screws C. Oven bake burner electrode bracket D. Oven bake burner electrode

A. Grasp electrode here. B. Bracket

8. Apply masking tape to the end of a 1/4" (6.4 mm) nut driver

12. Replace oven bake burner electrode inside bracket.

A. Oven bake burner electrode B. Oven bake burner electrode bracket

13. Reinstall the oven bake burner and oven bake burner

screws. See Step 5 for illustration.

A. Gas orice spud

9. Gas orice studs are stamped with a letter and a number.

Install the Number 105 oven bake burner orice spud.

10. Place Natural gas orice in plastic parts bag for future use,

and keep with package containing literature.

11. Push down on the clip on the electrode bracket.

Replace Oven Bake Burner Cover

1. Align rear shoulder screw mounting holes (keyholes) on the

oven bake burner cover with shoulder screws in the bottom of the oven.

A. Shoulder screw mounting holes (keyholes) B. Shoulder screws

2. Drop cover and slide to left or right to slide shoulder screws

into narrow ends of keyholes, and lock into place.

A. Oven bake burner electrode bracket B. Electrode bracket clip

A. Bake burner cover

Complete Installation

1. Refer to the “Make Gas Connection” section for properly

connecting the range to the gas supply.

2. Refer to the “Electronic Ignition System” section for proper

burner ignition, operation, and burner ame adjustments. IMPORTANT: You may have to adjust the “LO” setting for

each range burner. Checking for proper range burner ame is very important.

The small inner cone should have a very distinct blue ame 1/4" (6.4 mm) to 1/2" (1.3 cm) long. The outer cone is not as distinct as the inner cone. Propane gas ames have a slightly yellow tip.

3. Refer to “Complete Installation” in the “Installation

Instructions” section of this manual to complete this procedure.

To Convert Gas Pressure Regulator from Propane to Natural Gas

NOTE: Door must be removed in order to remove or replace kick

plate. Refer to the “Remove Door” section.

1. Lift the kick plate up and off of the kick plate tab.

Natural Gas Conversion

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

1. Turn the manual shut-off valve to the closed position.

A. Kick plate B. Kick plate tab C. Kick plate slot

2. Gently lay kick plate aside to avoid scratching the stainless

steel.

3. Locate the gas pressure regulator at the left rear of the

range.

A. Gas pressure regulator

4. Remove the gas pressure regulator cap by using a

large at-blade screwdriver, turning the regulator cap counterclockwise.

NOTE: Do not remove the spring beneath the cap.

A. To range B. Shut-off valve (closed position) C. Gas supply line

2. Unplug range or disconnect power.

5. Turn over the gas pressure regulator cap, and reinstall on the

regulator so that the hollow end faces in and the letters “NAT” are visible.

6. Tighten the gas pressure regulator cap by using a large at-

blade screwdriver, turning the regulator cap clockwise.

7. Test the gas pressure regulator and gas supply line.

The regulator must be checked at a minimum 1" (2.5 cm) water column above the set pressure. The inlet pressure to the regulator should be as follows for operation and checking the regulator setting:

Natural Gas:

Minimum pressure: 6" (15.2 cm) WCP Maximum pressure: 14" (35.6 cm) WCP

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least 1" (2.5 cm) water column pressure above the manifold pressure shown on the model/serial/rating plate.

Line pressure testing above 1/2 psi (3.5 kPa) gauge (14" [35.6cm] WCP)

The range and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).

Line pressure testing at 1/2 psi (3.5 kPa) gauge (14" [35.6cm]WCP) orlower

To Convert Surface Burners from Propane to Natural Gas

1. If the burner grates are installed, remove them.

2. Remove burner cap.

3. Remove the burner base by rst removing (2) T-20 screws.

Burner

A. Burner cap B. Screws C. Burner base

4. Apply masking tape to the end of a 1/4" (6.4 mm) nut driver

5. Replace with correct Natural gas orice spud. See the

“Natural Gas Orice Spud/Hood Chart.” Use the following chart to nd the exact orice spud placement.

Natural Gas Orice Spud/Hood Chart

Burner Rating

9,200 BTUs 130

18,000 BTUs (REAR) 20,000 BTUs (FRONT)

16,000 BTUs 180 1.80 mm Grill burner

NOTE: Refer to serial tag for more information on burner ratings and locations.

Stamp Size Burner Style

193 78 203 78

1.30 mm

0.70 mm

1.93 mm

0.78 mm

2.03 mm

0.78 mm

Small burner - main Small burner - simmer

Large burner – main Large burner – simmer Large burner – main Large burner – simmer

Burner orice spud

A. Size stamp B. Fuel type stamp (L or N)

6. Place Propane gas orice spuds in plastic parts bag for

future use and keep with package containing literature.

7. Replace the burner base and screws. Tighten screws only

until burner is snug to cooktop, do not over-tighten.

8. Replace burner cap.

9. Repeat steps 2 through 8 for the remaining burners.

Adjusting Simmer Low and Main Low Settings on Surface Burner for Natural Gas

1. Remove the surface burner control knobs and bezels (oven

control knobs and griddle control knobs do not have to be removed).

2. Locate the Simmer low-turndown adjustment screw through

the bezel on the left side of the ignition switch.

A B C

To Adjust Flame Height:

1. Unplug range or disconnect power.

2. Remove burner grates.

3. Remove the control knobs.

4. Open the oven door and remove the two screws on each

side of the range that hold the control console in place.

A. Simmer low-turndown adjustment screw B. Ignition switch C. Main low-turndown adjustment screw (inside stem)

3. With the burner ON, and set to Simmer Lo, adjust the

simmer ame down to the proper BTU level. Using a 1/8" x 4¼" (3.2 mm x 108 mm) at blade screwdriver, turn the simmer low-turndown adjustment screw counterclockwise until the ame becomes stable, does not icker, or appear to race around the burner. Once the ame is stable, turn the burner rate to SIMMER HIGH setting. The ame should increase to approximately 2X the ame height. If not, the low-turndown may be able to be adjusted low and still remain stable. Repeat this step for all surface burners, except the grill burner.

NOTE: Use a knob to adjust the burner valve. NOTE: If your range has the IR grill, then skip ahead to the

Convert IR Grill Burner section.

NOTE: Adjust each burner individually.

4. With burner OFF, using the same at blade screwdriver, turn

the main low-turndown adjustment screw 120-135 degrees counterclockwise. This will set the main low burner rate to a proper level.

5. Replace the bezels using the 2 screws which attach to the

valve brackets.

6. Push the surface knobs onto the valve stems.

7. Replace burner grates.

Flame Height

NOTE: Make sure to leave oven door open or the control

console will not rest in the side brackets properly once it is detached.

5. Pull up on the control console and let it drop forward into the

notched console brackets on each side.

A. Control console bracket

6. Put a control knob onto the valve stem of the burner you

want to adjust.

The cooktop ame should be a steady blue ame approximately 1/4" (6.4 mm) high.

Burner

A. Upper (main) ame B. Lower (simmer) ame

7. Turn the control knob to LO and, using a butane extension

lighter, light the burner.

8. Remove the control knob.

9. Use a 1/8" x 4¼" (3mmx100mm) at-blade screwdriver to

adjust the ame height. Tighten screw to reduce ame height. Loosen screw to increase ame height.

To Convert IR Grill Burner for Natural Gas

1. Unplug range or disconnect power.

2. Remove grill knob and bezel. The other surface knobs and

bezels should still be off the range.

3. Open the oven door and remove the two screws on each

side of the range that hold the control console in place.

A. Single ame burner adjustment screw (on right side of valve) B. Dual ame burner adjustment screw (on left side of valve)

10. When nished adjusting the ame height, put a control knob

back onto the valve stem and turn off the burner.

11. Remove the control knob.

12. Repeat steps 6 through 13 for any other burners that

need adjustment.

13. Lift up on the control console and set it back into place. For

a proper t, the ange of the control console must hook over the lip on the front of the range cooktop.

A. Control console ange B. Front lip of range cooktop

14. Check that the control console is ush with the top edge of

the range.

NOTE: Make sure to leave oven door open or the control console will not rest in the side brackets properly once it is detached.

4. Pull up on the control console and let it drop forward into the

notched console brackets on each side.

A. Control console bracket

5. Remove the two screws holding the grill orice holder

bracket.

A. Flush with range top

15. Replace the two screws on each side of the control console.

16. Replace the control knobs.

17. Replace burner grates.

18. Test the ame by turning the control from LO to HI, checking

the ame at each setting.

A. Screws B. Grill orice holder bracket

6. Pull the grill orice holder out of the burner box far enough

away to allow access to the orice with a wrench, using caution not to kink the attached tubing.

10. Check that the control console is ush with the top edge of

the range.

A. Flush with range top

11. Replace the screws on each side of the control console.

12. Replace the control knobs and bezels.

13. Replace burner grates.

A. Grill orice B. Grill orice holder

7. Using an adjustable wrench and a 1/2" (1.3 cm) open end

wrench remove the Propane (L) orice spud and replace with the correct Natural Gas (NG) orice spud. See Natural Gas Orice Spud Chart.

Use 1/2" (1.3 cm) open end wrench to remove/replace orifice

Hold with adjustable wrench here

8. Reposition the grill orice holder assembly back into the

burner box, and replace the grill orice holder bracket and two holder screws.

9. Lift up on the control console and set it back into place. For

a proper t, the ange of the control console must hook over the lip on the front of the range cooktop.

NOTE: It may be necessary to lift valve stems to align with console holes.

Convert Oven Bake Burner (30" [76.2 cm] and 36" [91.4 cm] models and the right oven cavity on 48" [121.9 cm] models)

1. Slide the bake burner cover to the right or left.

A. Bake burner cover

2. Lift up and remove oven bake burner cover, and set aside.

3. Using a 1/4" (6.4 mm) nut driver, unscrew oven bafe nuts

and remove oven bafe. Set aside.

A. Control console ange B. Front lip of range cooktop

A. Oven bafe B. Oven bafe nuts

+ 78 hidden pages