How it Works
Jenn-Air
Loading...
JGCP430W
Product Dimensions
2 pgs350.33 Kb0

Jenn-Air JGCP430W, JGCP436W, JGCP536W, JGCP548W Product Dimensions

PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS
JGCP430W JGCP436W
JGCP536W JGCP548W
Type of Gas Natural Gas:
This cooktop is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.
●
LP Gas conversion:
Conversion must be done by a qualified service technician. No attempt shall be made to convert the cooktop from the
gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. To convert to LP gas, use the LP gas converision kit provided with the cooktop and see the “Gas Conversions” section.
Electrical:
●
A 120 volt, 60 Hz, AC only, 15-amp, fused electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this cooktop be provided.
●
Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.
Ref. W10145395
03/05/2010
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.
●
It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop burner base.
●
It is recommended that a 600 CFM or larger vent hood be installed above the cooktop.
●
It is not recommended that a microwave hood combination be mounted above the cooktop.
●
The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.
●
All openings in the wall or floor where cooktop is to be installed must be sealed.
●
Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.
●
Grounded electrical supply is required. See “Electrical Requirements” section.
●
Proper gas supply connection must be available. See “Gas Supply Requirements” section.
●
The cooktop is designed to hang from the countertop by its side or rear flanges.
●
The gas and electric supply should be located as shown in “Gas and Electric Connection Locations” section so that they are accessible without requiring removal of the cooktop.
●
Provide cutout in left rear corner of cutout enclosure as shown to provide clearance for gas inlet, power supply cord, and to allow the rating label to be visible.
IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.
Mobile Home - Additional Installation Requirements
The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part
280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes.
In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.
C
Page 1 of 2
Commercial Style Gas Cooktop
A
E
D
A. 27
" (68.9 cm)
¹⁄₈
B. 30" (76.2 cm) cooktop:
29
⁷⁄₈
" (75.1 cm) actual width 36" (91.4 cm) cooktop: 35
" (90.4 cm) actual width
⁷⁄₈
48" (121.9 cm) cooktop: 47
⁷⁄₈
" (120.8 cm) actual width
Side View of Cooktop
G
F
A. 27¾" (70.5 cm) B. 1¼" (3.2 cm)
⁷⁄₁₆
" (18.8 cm)
C. 7
D. Gas inlet is located 1
the cooktop burner base and 4 from left-hand side of the cooktop burner base.
C. Island trim or optional backguard D. 36" (91.4 cm) long 3 prong grounding-
type power supply cord
E. Model/serial rating plate (located on the
underside of the cooktop burner base)
A
E
" (4.8 cm) from the back of
⁷⁄₈
⁷⁄₈
" (12.4 cm) in
B
B
C
D
E. 22" (55.9 cm)
⁵⁄₁₆
" (8.4 cm)
F. 3
⁹⁄₁₆
" (1.4 cm)
G.
CABINET REQUIREMENTS
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.
Ref. W10145395
03/05/2010
Page 2 of 2
Commercial Style Gas Cooktop
Gas and Electric Connection Locations
A
O
E
D
N
A. Grounded 3-prong outlet should be located on
left-hand side of the cutout 16" (40.6 cm) max. from enclosure sidewall
B. 10" (25.4 cm) min. clearance from countertop to
top of the outlet C. 14" (35.6 cm) countertop to the gas supply line D. Gas supply line should be located in this area on
rear or side walls, or the supply line can come up
B
C
through the floor.
NOTE: Solid side and bottom of cutout enclosure not shown.
D
A. See chart.
C
P
F
L
J
I
K
D
E
C
G
A**
B min.*
H
L
M
B. See chart.
C. See chart.
D. See chart.
E. See chart.
F. 18" (45.7 cm) min. clearance upper
cabinet to countertop
¾
" (1.9 cm) back of cabinet cutout to gas
G.
opening cutout
6⁷⁄₈
H.
" (16.1 cm) gas opening cutout depth
I.
12½
" (31.7 cm) gas opening cutout width
22¼
J. " (56.5 cm) cabinet cutout depth
K. 2" (5.1 cm) cabinet side to gas cutout
L. 6" (15.2 cm) min. distance on both sides of the
cooktop to the side wall or other combustible material above cooking surface
M. 24" (61.0 cm) cabinet depth
7¼
N. " (18.4 cm) cabinet depth to countertop O. Notch to be equal on both sides
P. 13" (33.0 cm) upper cabinet depth
Size Model A**
Size Model A**
30" (76.2 cm) KGCU407 30" (76.2 cm) ) 30" (76.2 cm) or
30" (76.2 cm) JGCP430 1¾" (4.4 cm)** 30" (76.2 cm) 30" (76.2 cm) 29¼" (74.3 cm) 30" (76.2 cm) or
36" (91.4 cm) KGCU462
36" (91.4 cm) JGCP436
KGCU463 KGCU467
JGCP536
48" (121.9 cm) KGCU482
48" (121.9 cm) JGCP548 1¾" (4.4 cm)** 42" (106.7 cm) 48" (121.9 cm) 47¼" (120.0 cm) 48" (121.9 cm) or
KGCU483 KGCU484
Cooktop Cutout
Cooktop Cutout
to Back Wall
to Back Wall
1¾" (4.4 cm)**
1½" (3.8 cm)**
1¾" (4.4 cm)** 42" (106.7 cm) 36" (91.4 cm) 35¼" (89.5 cm) 36" (91.4 cm) or
1¾" (4.4 cm) 1¾" (4.4 cm)
1½" (3.8 cm)** 1¾" (4.4 cm)** 1½" (3.8 cm)**
*NOTES: Dimension “B” can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet is covered by not less than
0.25" (6.4 mm) flame retardant millboard covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel,
*NOTES: Dimension “B” can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet is covered by not less than
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
0.25" (6.4 mm) flame retardant millboard covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel,
If installing a range hood above the cooktop, follow the range hood instructions for dimensional clearances above the cooktop
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
surface.
If installing a range hood above the cooktop, follow the range hood instructions for dimensional clearances above the cooktop
**NOTE: If backwall is constructed of a combustible material and a backguard is not installed, a minimum clearance of dimension A +
surface.
6" (15.2 cm) is required for
48" (121.9 cm) cooktops and cooktops with a grill.
B*
B*
Cooktop to
Cooktop to
Cabinet
Cabinet
42" (106.7 cm)
42" (106.7 cm)
C
C
Optional
Optional
Backguard and
Backguard
Upper Cabinet
Opening
Opening
D
D
Cabinet and
Cabinet and
Countertop
Countertop
30" (76.2 cm) 29¼" (74.3 cm)
36" (91.4 cm)
35¼" (89.5 cm)
48" (121.9 cm)
47¼" (120.0 cm) 48" (121.9 cm) or
E
E
Countertop Only
Countertop Only
29 (75.9 cm) for
⁷⁄₈"
29⁷⁄₈" (75.9 cm) for
zero clearance
zero clearance
36" (91.4 cm) or
⁷⁄₈"
35 (91.1 cm) for zero clearance
35⁷⁄₈" (91.1 cm) for zero clearance
⁷⁄₈"
47 (121.6 cm) for zero clearance
47⁷⁄₈" (121.6 cm) for zero clearance
**NOTE: If backwall is constructed of a combustible material and a backguard is not installed, a minimum clearance of dimension
A + 3" (7.6 cm) is required for 36" (91.4 cm) and 48" (121.9 cm) cooktops.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use