Jenn-Air JGC8536BDW11, JGC8536BDS11, JGC8536BDB11, JGC8430CDW11, JGC8430CDS11 Owner’s Manual

...

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_

JENN-AIRGASCOOKTOPS

£_ii_ii_ iiiiiiiiiiiiiiiiiiiiiiii

°i

TABLE OF CONTENTS

Important Safety Instructions .....................................1-4

Using Your Cooktop ......................................................5-6

Care & Cleaning ..................................................................7

Troubleshooting ..................................................................8

Warranty & Service .............................................................9

Guide de I'utilisation et entretien ................................10

Guia de Uso y Cuidado ...................................................19

iiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!i!!i!i!iiiii_i_i_i_I

_JENN-AIR

Form No. A/01/08 Part No. 8111 P537-60

1 8/8/06, 8:40 AM

Litho U.S.A.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified technician. Do not attempt to adjust, repair, service, or replace any part of your appliance unless it is specifi- cally recommended in this guide. All other servicing should be referred to a qualified servicer. Have the installer show you the location of the gas shut off valve and how to shut it off in an emergency.

Always disconnect power to appliance before servicing.

IM SAF

|NSTRUCT|ONS

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintain- ing, or operating the appliance.

Always contact your dealer, distributor, service agent, or

manufacturer about problems or conditions you do not understand.

Recognize Safety Symbols, Words, Labels

Read and follow all instructions before using this appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a result of improper usage of the appliance. Use appliance only for its intended purpose as described in this guide.

2 8/8/06, 8:41 AM

SAF Y INSTRUCTIONS

To Prevent Fire or

Smoke Damage

Be sure all packing materials are removed from the appliance before operating it.

Keep area around appliance clear and free from com- bustible materials, gasoline, and other flammable

vapors and materials.

If appliance is installed near a window, proper precau- tions should be taken to prevent curtains from blowing

over burners. Many aerosol-type spray cans are EXPLOSIVE when

exposed to heat and may be highly flammable. Avoid their use or storage near an appliance.

Many plastics are vulnerable to heat. Keep plastics away from parts of the appliance that may become

warm or hot. Do not leave plastic items on the cooktop

as they may melt or soften if left too close to a lighted surface burner.

Child Safety

NEVER leave children alone or unsupervised near the appliance when it is in use or is still hot.

NEVER allow children to sit or stand on any part of the

appliance as they could be injured or burned. Children must be taught that the appliance and utensils

on it can be hot. Let hot utensils cool in a safe place, out of reach of small children. Children should be

taught that an appliance is not a toy. Children should not be allowed to play with controls or other parts of the

unit.

About Your Appliance

To eliminate the hazard of reaching over hot surface

burners, cabinet storage should not be provided directly above a unit. If storage is provided, it should be limited to items which are used infrequently and which are safely stored in an area subjected to heat from an appliance. Temperatures may be unsafe for some items, such as volatile liquids, cleaners or aerosol sprays.

A faint gas odor may indicate a gas leak. If a gas odor is

detected, shut off the gas supply to the cooktop. Call

your installer or local gas company to have the possible

leak checked. Never use a match or other flame to locate a gas leak.

in Case of Fire

Turn off appliance and ventilating hood to avoid

spreading the flame. Extinguish flame then turn on hood to remove smoke and odor.

• Smother fire or flame in a pan with a lid or cookie sheet.

* NEVER pick up or move a flaming pan. Do not use water on grease fires. Use baking soda, a

dry chemical or foam-type extinguisher to smother fire or flame.

Do not use the cooktop as a storage area for food or cooking utensils.

Potentially hot surfaces include cooktop, and areas facing the cooktop.

Cooking Safety

Always place a pan on a surface burner before turning

it on. Be sure you know which knob controls which surface burner. Make sure the correct burner is turned

on and that the burner has ignited. When cooking is completed, turn burner off before removing pan to prevent exposure to burner flame.

Always adjust surface burner flame so that it does not

extend beyond the bottom edge of the pan. An exces- sive flame is hazardous, wastes energy and may dam- age the appliance, pan or cabinets above the appliance.

3 8/8/06, 8:41 AM

SAF Y INSTRUCnONS

NEVER leave a surface cooking operation unattended especially when using a high heat setting or when deep fat frying. Boilovers cause smoking and greasy spillovers may ignite. Clean up greasy spills as soon as possible. Do not use high heat for extended cooking operations.

NEVER heat an unopened container on the surface burner. Pressure build-up may cause container to burst resulting in serious personal injury or damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause burns from steam. Dishtowels or other substitutes

should never be used as potholders because they can trail across hot surface burners and ignite or get caught on appliance parts.

Always let quantities of hot fat used for deep fat frying

cool before attempting to move or handle. Do not let cooking grease or other flammable materials

accumulate in or near the appliance, hood or vent fan. Clean hood frequently to prevent grease from accumu- lating on hood or filter. When flaming foods under the

hood turn the fan on. NEVER wear garments made of flammable material or

loose fitting or long-sleeved apparel while cooking. Clothing may ignite or catch utensil handles.

Utensil Safety

Use pans with flat bottoms and handles that are easily grasped and stay cool. Avoid using unstable, warped, easily tipped or loose-handled pans. Also avoid using pans, especially small pans, with heavy handles as they could be unstable and easily tip. Pans that are heavy to move when filled with food may also be hazardous.

Be sure utensil is large enough to properly contain food and avoid boilovers. Pan size is particularly important in deep fat frying. Be sure pan will accommodate the

volume of food that is to be added as well as the bubble

action of fat.

To minimize burns, ignition of flammable materials and

spillage due to unintentional contact with the utensil, do not extend handles over adjacent surface burners.

Always turn pan handles toward the side or back of the

appliance, not out into the room where they are easily hit or reached by small children.

Never let a pan boil dry as this could damage the utensil and the appliance.

Only certain types of glass, glass/ceramic, ceramic or glazed utensils are suitable for cooktop usage without breaking due to the sudden change in temperature. Follow manufacturer's instructions when using glass.

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices or accessories that are not specifically recommended in this guide. Do not use eyelid covers for the surface units or stovetop grills. The use of devices or accesso- ries that are not expressly recommended in this manual can create serious safety hazards, result in performance problems, and reduce the life of the components of the appliance.

Cleaning Safety

Turn off all controls and wait for appliance parts to cool

before touching or cleaning them. Do not touch the burner grates or surrounding areas until they have had

sufficient time to cool. Clean appliance with caution. Use care to avoid steam

burns if a wet sponge or cloth is used to wipe spills on a hot surface. Some cleaners can produce noxious fumes if applied to a hot surface.

Important Safety Notice and

Warning

The California Safe Drinking Water and Toxic Enforce-

ment Act of 1986 (Proposition 65) requires the Governor of California to publish a list of substances known to the State of California to cause cancer or reproductive harm, and requires businesses to warn customers of potential exposures to such substances.

Users of this appliance are hereby warned that the burning of gas can result in low-level exposure to some of the listed substances, including benzene, formalde- hyde and soot, due primarily to the incomplete combus- tion of natural gas or liquid petroleum (LP) fuels. Properly adjusted burners will minimize incomplete combustion. Exposure to these substances can also be minimized by properly venting the burners to the

outdoors. IMPORTANT NOTICE REGARDING PET BIRDS:

Never keep pet birds in the kitchen or in rooms where the fumes from the kitchen could reach. Birds have a

very sensitive respiratory system. Fumes released during

an oven self-cleaning cycle may be harmful or fatal to birds. Fumes released due to overheated cooking oil, fat, margarine and overheated non-stick cookware may be equally harmful.

4 8/8/06, 8:41 AM

SAF Y INSTRUCTIONS

Electrical Connection

Appliances which require electrical

power are equipped with a three= prong grounding plug which must be

plugged directly into a properly grounded three-hole 120 volt

electrical outlet.

Always disconnect power to appliance before servicing. The three-prong grounding plug offers protection

against shock hazards. DO NOT CUT OR REMOVE

THE THIRD GROUNDING PRONG FROM THE

POWER CORD PLUG.

If an ungrounded, two-hole or other type electrical outlet is encountered, it is the personal responsibility of the appliance owner to have the outlet replaced

with a properly grounded three=hole electrical

outlet.

Save These instructions for Future Reference

5 8/8/06, 8:41 AM

Usl You Coo oP

Surface Controls

Surface Control

Knobs ....

Use to turn on the surface burners. An infinitechoice of heat settings is available

from Lo to Hi. At the Hi setting a detent .........

or notch may be felt.

Pilotless

ignition

Pilotless ignition eliminates the need for

a constant standing pilot light. Each surface

burner has a spark ignitor.Use care when

cleaning around the surface burner.

If the surface burner does not light, check if

ignitor is broken, soiled or wet.

Setting the Controls

Your cooktop has sealed gas burners with automatic re- ignition,if the burner flame should go out, the system will

automatically spark to re-ignite the burner.

BURNER CAP

BURNER BASE

Operating During a

Power Failure

1. Hold a lighted match to the desired surface burner head.

2. Push in and turn the control knob slowly to the desired setting.

Suggested Heat Settings

The size and type of cookware will affect the heat setting.

For informationon cookware and other factors affecting heat settings, refer to "Cooking Made Simple" booklet.

Use Hi to bring liquid to a boil, or reach pressure in a pressure cooker. Always

reduce setting to a lower heat when liquids begin to boil or foods begin to

cook.

An intermediate flame size is used to

continue cooking. Food will not cook any faster when a higher flame setting is

used than needed to maintain a gentle boil. Water boils at the same tempera-

ture whether boiling gently or vigorously.

Use Lo to simmer foods, keep foods

warm and melt chocolate or butter.

Some cooking may take place on the Lo setting if the pan iscovered, it is

possible to reduce the heat by rotating the knob toward OFF. Be sure flame is

stable.

1. Place a pan on the burner grate. (To preserve the grate finish, do not operate the burners without a pan on the

grate to absorb the heat from the burner flame.)

2. Push in knob and turn immediately counterclockwise to the desired setting.

A clicking (spark) sound will be heard and the burner will light. (All ignitorswill spark when any surface

burner knob is turned on. However, only the selected burner will light.)

6 8/8/06, 8:41 AM

Usl You Coo oP

Cooktop at a Glance

MODEL JGC8536

i 2 3 4 5

1. Left rear surface burner (9,200 BTUs_).

2. Left front surface burner (5,000 BTUs on Hi, 650 BTUs on

Lo_.

3. Center surface burner (15,000 BTUs_).

4. Right front surface burner (12,500 BTUs).

5. Right rear surface burner (5,000 BTUs on Hi, 650 BTUs on

Lo_.

MODEL JGC8430B

I 2 34

1. Left rear surface burner (10,500 BTUs}.

2. Left front surface burner (5,000 BTUs on Hi, 650 BTUs on

Lo).

3. Right front surface burner (15,000 BTUs_).

4. Right rear surface burner (9,200 BTUs).

To prevent the cooktop from discoloring or

staining:

. Clean cooktop after each use. . Wipe acidic or sugary spills as soon as the cooktop has

cooled as these spills may discolor the surface.

Sealed Burners

The sealed burners are secured to the cooktop and are not

designed to be removed. Since the burners are sealed into the cooktop, boilovers or spills will not seep underneath the

cooktop. However, the burners should be cleaned after each use. The

head portion of the burner iseasily removed for cleaning. (See page 7 for cleaning directions.i)

High Performance Burner*

There is one high speed burner on your cooktop, located in

the center or right front position. This burner offers higher speed cooking that can be used to quickly bring water to a

boil and for large-quantity cooking.

Simmer Burners*

These burners are locatedin the left front position and/or the

right rear position. The simmer burner offers a lower BTU flame for delicate sauces or melting chocolate.

BTU ratings will vary when using LP gas.

Burner Grates

The grates must be properly positioned before cooking.

Improper installation of the grates may result in chipping of the cooktop. To ensure proper positioning, align bumpers on

grate bottom with the indentations in the cooktop.

Do not operate the burners without a pan on the grate.

The grate's porcelain finish may chip without a pan to

absorb the heat from the burner flame.

Although the burner grates are durable, they will gradually

lose their shine and/or discolor, due to the high temperatures of the gas flame.

Notes -

A properly adjusted burner with clean ports will light within a few seconds. If using natural gas, the flame will

be blue with a deeper blue inner cone. If the burner flame isyellow or is noisy, the air/gas

mixture may be incorrect.Contact a service technician to adjust. (Adjustments are not covered by the war-

ranty.i)

With LP gas, some yellow tips on the flames are accept-

able. This is normal and adjustment is not necessary.

With some types of gas, you may hear a "popping"

sound when the surface burner is turned off. This is a normal operating sound of the burner.

To improvecooking efficiency and to prevent possible

damage to the cooktop or pan, the flame must be adjusted so it does not extend beyond the edge of the pan.

Burner caps must be correctly placed on the burner base for proper operation of the burner.

7 8/8/06, 8:41 AM

CARE & CLEAN|

Cleaning Procedures

* Brand names for cleaning products are registered

trademarks of the respective manufacturers.

** To order direct, call 1-800-JENNAIR

(1-800-536-6247).

Removable Burner Caps

Sealed Gas

Burner

Burner Grates

Control Knobs

Cooktop and

Porcelain Enamel

Cooktop= Stainless Steel

(select models)

* Allow burner to cool. Remove burner cap and wash in soapy water with a plastic scouring pad. For

stubborn soils, clean with a soap-filled, nonabrasive pad or Cooktop Cleaning Creme (part #20000001)** and a sponge.

Do not clean in dishwasher or self-cleaning oven. Clean frequently. Allow burner to cool. Clean with soap and plastic scouring pad. For stubborn soils, clean

with a soap-filled, nonabrasive pad. Be careful not to get water into the center of the burner.

Use care when cleaning the ignitor.Ifthe ignitoriswet or damaged the surface burner will not light. To ensure even cooking performance, keep burner ports free of food soils/debris.

Wash grates with warm, soapy water and a nonabrasive, plastic scrubbing pad. For stubborn soils, clean with a soap-filled, nonabrasive pad or a sponge and Cooktop Cleaning Creme (part #20000001)** and a

sponge. If soil remains, reapply Cooktop Cleaning Creme, cover with a damp paper towel and soak for 30 minutes. Scrub again, rinse and dry. The grates are made of porcelain on cast iron and are very durable, however, they will gradually lose

their shine and/or discolor. This isdue to exposure to high temperatures from the gas flame. Do not clean in dishwasher or self-cleaning oven.

* Remove knobs inthe OFFposition by pulling up. * Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

* Turn on each burner to be sure the knobs have been correctly replaced.

Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid resistant, not acid proof.

All spillovers, especially acidic or sugary spillovers, should be wiped up immediately with a dry cloth.

When cool, wash with soapy water, rinse and dry. Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping. Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

* DO NOT USE ANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH. * ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

* DO NOT USE ORANGE OR ABRASIVE CLEANERS. * Daily Cleaning/Light Soil -= Wipe with one of the following - soapy water, white vinegar/water solution,

Formula 409 Glass and Surface Cleane¢ or a similar glass cleaner - using a sponge or soft cloth. Rinse and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (part No.

20000008)**.

, Nloderate/Heavy Soil == Wipe with one of the following -Bon Ami, Smart Cleanser, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi- purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

* Discoloration == Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse

immediately and dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

8 8/8/06, 8:41 AM

Surface burner fails to light.

Surface burner flame lifts * Check to be sure a pan is sitting on the grate above. off ports. • Contact an authorized Jenn-Air servicer.

The flame is uneven. * Burner ports may be clogged.

Surface burner flame is yellow in color.

* Check * Check

* Check * Check to be sure ignitor is dry and clicking. Burner will not light if ignitor is damaged,

* Check to be sure burner cap is correctly seated on the burner base.

• Flame may need to be adjusted. Contact an authorized Jenn-Air servicer. * Some yellow tips on the flame are acceptable when using LP gas.

* Contact an authorized Jenn-Air servicer.

to be sure plug is securely inserted into receptacle. or re-set circuit breaker. Check or replace fuse.

power supply. to be sure burner is correctly rated for your kind of gas.

to be sure burner ports or ignition ports are not clogged.

soiled or wet. If ignitor doesn't click, turn control knob OFF.

9 8/8/06, 8:41 AM

JENN-AIR COOKING APPLIANCEWARRANTY

LIM ITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will pay for factory specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Jenn-Air designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of original purchase date is required to obtain service under this limited warranty.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CERTAIN COMPONENT PARTS

In the second through fifth years from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, Jenn-Air will pay for factory specified parts for the following components (if applicable to the

product) if defective in materials or workmanship:

• Electric element • Electronic controls

• Touch Pad and microprocessor

• Glass ceramic cooktop: if due to thermal breakage

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.

3. Repairs when your major appliance isused for other than normal, single-family household use or when it is used in a manner that is contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Jenn-Air.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Jenn-Air servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions.

11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

• Magnetron tube

• Sealed gas burners

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies. If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling Jenn-Air. In the U.S.A., call 1-800-688-1100. In Canada, call 1-800-807-6777. 9/07

+ 22 hidden pages