JENN-AIR JGC8430CDW, JGC8430CDB, JGC8430CDS Dimension Guide
JENN-AIR® DETAILED PLANNING DIMENSIONS
A
A
B
A
B
C
D
G
F
H
30" GAS COOkTOP
JGC8430CD – 30" x 51⁄8" x 213⁄4"
PRODUCT DIMENSIONS
MODEL # JGC8430CD
Overall width
A
Depth to center of cooktop
B
TOP VIEW
E
B
G
F
C
D
Center of cooktop to center of gas inlet
C
Width of recessed cooktop
D
Height from gas inlet to countertop
E
Height of recessed cooktop
F
Height with grates
G
Center of gas inlet to recessed cooktop
H
Depth of recessed cooktop
I
1 of 4
in cm
30 76.2
3
⁄4 55.2
21
1
⁄2 31.6
12
1
⁄2 72.1
28
1
⁄8 12.9
5
3
⁄4 9.4
3
7
⁄8 2.2
3
⁄4 4.4
1
1
⁄4 51.5
20
FRONT VIEW
SIDE VIEW
B
I
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120035A 07/2012
JENN-AIR® DETAILED PLANNING DIMENSIONS
C* F
D
A
B
B
e
Side
Cabinet
E
g
F
Side
Cabinet
G
30" GAS COOkTOP
JGC8430CD – 30" x 51⁄8" x 213⁄4"
2 of 4
OPENING/CLEARANCE DIMENSIONS
A
C*
B
E
g
FRONT VIEW
Side
Cabinet
F
e
G
MODEL # JGC8430CD
in cm
Width of combustible area above
A
cooking surface (min.)
Width from cooktop to fixed wall
B
or other combustible material (min.)
Height to bottom of uncovered wood or
C*
metal cabinet above cooking surface (min.)
Height to bottom of uncovered wood
D
or metal cabinet (min.)
Height to top edge of electrical and gas
E
D
B
installation area
Depth of upper cabinet (recommended) 13 33.0
F
Depth from cutout to wall (min.)
G
Width of cutout 28
H
Depth of cutout 20
I
Depth from cutout to front of
J
countertop (min.)
e
Recommended electrical access location
g
Recommended gas supply line location
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet
is covered by not less than
less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5 mm) copper.
If installing a hood or microwave hood combination above the cooktop, follow the
hood or microwave hood combination instructions for dimensional clearances above
the cooking surface.
1
⁄4" (0.6 cm) flame retardant millboard covered with not
30 76.2
8 20.3
30 76.2
18 45.7
7
3
⁄8 9.7
3
⁄4 1.9
3
⁄4 73.0
5
⁄8 52.4
2 5.1
GAS REQUIREMENTS
Natural Gas
This cooktop is factory-set for use with natural gas.
LP Gas Conversion
Conversion must be done by a qualified service technician. To convert
to LP gas, use the LP gas conversion kit provided with the cooktop.
ELECTRICAL REQUIREMENTS
120 volt, 60 Hz, AC only, 20-amp fused, grounded circuit is required.
A time-delay fuse or dedicated circuit is recommended. Minimum power
cord length is 46" (117.0 cm).
LOCATION REQUIREMENTS
• To ensure cooktop base clearance, cabinet side walls need to be wider
than the cutout.
• If cabinet has a drawer, allow a 4" (10.2 cm) minimum clearance between
countertop and top of drawer. Drawer depth may need to be shortened to
avoid interfering with the regulator.
COOKTOP OVER SINGLE WALL OVEN INSTALLATION
REQUIREMENTS
• For approved model number combinations, refer to the under counter
• To install a cooktop over a 30" single wall oven, refer to page 3.
label on the bottom of the cooktop burner box.
H
G
I
SIDE VIEW
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
TOP VIEW – CUTOUT
J
JRC120035A 07/2012
Loading...