Jenn-Air JED8345ADW, JED8345ADB Dimension Guide
JENN-AIR® DETAILED PLANNING DIMENSIONS
A
B
C
F
A
A
A
B
C
I
J
D
GE
F
DESIGNER LINE MODULAR ELECTRIC DOWNDRAFT COOKTOP
JED8345AD – 45" x 143⁄4" x 213⁄4"
PRODUCT DIMENSIONS
MODEL # JED8345AD
Overall width 45 114.3
A
Depth to corner of cooktop 21
B
Depth to center of cooktop 21
C
Width of recessed cooktop 43 109.2
D
Width of blower motor assembly 14
E
Width to hard wire opening 14
F
Width from plenum to
G
recessed cooktop
Height from blower motor
H
to countertop
Height with grill grates
I
Height of recessed cooktop 3
J
Depth of recessed cooktop 20
K
TOp VIEW
B
C
A
I
D
1 of 3
in cm
1
⁄2 54.7
3
⁄4 55.2
3
⁄8 36.5
5
⁄8 37.0
26 65.9
3
14
⁄4 37.5
5
⁄8 1.5
1
⁄2 8.9
7
⁄8 53.0
H
FRONT VIEW
SIDE VIEW
J
GE
B
K
H
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120025 03/2012
JENN-AIR® DETAILED PLANNING DIMENSIONS
J
BB
K
Side
Cabinet
E*
F
D
e
A
B
B
v
I**
H
v
G
C
DESIGNER LINE MODULAR ELECTRIC DOWNDRAFT COOKTOP
JED8345AD – 45" x 143⁄4" x 213⁄4"
OPENING/CLEARANCE DIMENSIONS
MODEL # JED8345AD
Width of combustible area above
A
cooking surface (min.)
Width from cooktop to fixed wall
B
or other combustible material (min.)
A
E*
F
G
C
H
v
D
e
I**
v
D
FRONT VIEW
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet is
**Based on installation in a 24" (61.0 cm) base cabinet.
ELECTRICAL REQuIREMENTS
240 volt, 60 Hz, AC only, 50-amp fused, grounded circuit is required.
A dedicated circuit is recommended.
LOCATION REQuIREMENTS
• To ensure cooktop base clearance, cabinet side walls need to be wider
Side
Cabinet
• Grills installed near a side wall must allow a minimum clearance of 6" (15.2 cm)
• A minimum clearance of 2" (5.1 cm) is recommended between the
J
• For removal of the supplied grease container(s), a minimum clearance
K
• An under counter built-in oven cannot be installed under this cooktop.
SIDE VIEW TOp VIEW – CuTOuT
Width of recommended electrical
C
installation area
Width to center of vent opening option 9
D
Height to bottom of uncovered wood or
E*
metal cabinet above cooking surface (min.)
Height to bottom of uncovered wood
F
or metal cabinet (min.)
Height to top edge of recommended electrical
G
installation area (min.)
Height to center of vent opening option 13 33.0
H
Depth to center of vent opening option 15
I**
Depth of upper cabinet (recommended) 13 33.0
J
Depth from cutout to wall (min.)
K
Width of cutout 43
L
Depth of cutout 21 53.3
M
Depth from cutout to front of countertop (min.) 1
N
e
Recommended electrical access location
Recommended venting location –
v
see page 3 for ducting information
covered by not less than
No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
than the cutout.
between the cooktop and side wall for maximum performance.
blower motor and cabinet for proper cooling. A 6" (15.2 cm) clearance
is recommended for servicing access.
of 61⁄4" (15.9 cm) is required.
L
2 of 3
in cm
45 114.3
1 2.5
1
12
⁄4 31.0
3
⁄8 23.8
30 76.2
18 45.7
4 10.0
1
⁄2 39.5
3
⁄4 1.9
1
⁄4 109.9
7
⁄8 4.8
1
⁄4" (0.6 cm) ame retardant millboard covered with not less than
K
M
N
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120025 03/2012
Loading...