Jenn-Air JED8130ADB, JED8130ADW, JED8230ADB, JED8230ADS, JED8230ADW Dimension Guide
www.dexpress.com DIMENSION EXPRESS Fax on Demand (775) 833-3600
This Data Sheet Includes Information On
30"
Jenn-Air
• Product Model Number (s): •
30" Convertible Cooktops:
see below
JED8130ADB, JED8130ADW, JED8230ADB,
JED8230ADS and JED8230ADW
Side View (not to scale)
• Dimensions (Actual Size) •
Overall width:
Overall depth:
Distance from top of counter to bottom of unit:
Cut-Out width:
Cut-Out depth:
30"
21 3/4"
see below
29"
21"
Min. spacing from cooktop edge to nearest
vertical combustible wall to the RIGHT:
8"
21"
29"
Overall Dimensions
Top View (not to scale)
Cut-Out Dimensions
Countertop View
(not to scale)
Min. spacing from cooktop edge to nearest
vertical combustible wall to the LEFT:
8"
Min. spacing from cooktop edge to nearest
vertical combustible wall to the REAR:
Minimum spacing to front edge of counter:
15/16"
1 7/8"
Minimum distance between cooktop
and cabinet directly above:
Minimum width of cabinet directly above:
Maximum depth of cabinets directly
above and adjacent:
30"
30"
13"
Cabinet Requirements
Wall View
(not to scale)
30"
Minimum distance between countertop
and adjacent cabinet above:
18"
• Additional Information •
• Cabinetry over cooktop : 30" minimum clearance
between the top of the cooking surface and the bottom
of an unprotected wood or metal cabinet. 24" minimum
when bottom of wood or metal cabinet is protected by
not less than 1/4" flame retardant millboard covered
with not less than no. 28 MSG sheet steel, 0.015"
stainless steel, 0.024" aluminum or copper.
30"
18"
Minimum horizontal
clearance between the
edge of the appliance
and combustible
construction extending
from the cooking
surface to 18" above
the cooking surface is
8" (see solid areas).
• To eliminate the hazard of reaching over heated
surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage
is to be provided, the hazard can be reduced by
installing a range hood that projects horizontally a
minimum of 5" beyond the bottom of the cabinets.
• Countertop must be supported within 3" of cutout.
Grease container
• Radius corners of cutout and file to insure smooth
edges and prevent corner cracking (1/4" radius).
• Blower can be swiveled 90°.
See page 2-3 for additional information
13 13/16"
Minimum
clearance
required
3 1/2"
Front View
of Cooktop and
Attached Blower
Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2002.
• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
Provide 2" min. cabinet
clearance to motor for
cooling purpose. 6"
recomended for servicing.
321
BN182.34 • A321B149C150 • • 032603 • 95657 • 68517
11 13/16"13 3/4"
(not to scale)
21 3/4"
www.dexpress.com
DIMENSION EXPRESS
Fax on Demand (775) 833-3600
Additional Information:
• Electric supply: 120/240 VAC, 60Hz. 55 amp grounded circuit is
required, Power cord is NOT supplied.
• Duct requirements: See page 3 for ducting information and below for
location.
• 6 1/4" Under counter access must be provided to remove and empty
grease container(s).
Duct locations
(not to scale)
Page 2
This Data Sheet Includes Information On
Jenn-Air
• Product Model Number (s): •
30" Convertible Cooktops:
JED8130ADB, JED8130ADW, JED8230ADB,
JED8230ADS and JED8230ADW
7 9/16"
13"
9 3/8"
Top of counter to centerline of back duct location: 13"
Left edge of cutout to centerline of back and bottom duct locations: 9 3/8"
Front edge of cutout to centerline of bottom duct location: 7 9/16"
Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2002.
• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
BN182.34 • A321B149C150 • • 032603 • 95657 • 68517
149
Loading...