JENN-AIR JED4430GB, JED3430GS, JED4536KS, JED4536KB, JED4536GS Installation Instructions

...

30" (76.2 CM) AND 36" (91.4 CM)

ELECTRIC DOWNDRAFT COOKTOP

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION DE LA TABLE DE CUISSON ÉLECTRIQUE AVEC ASPIRATION

PAR LE BAS DE 30" (76,2 CM) ET 36" (91,4 CM)

Table of Contents/Table des matières

COOKTOP SAFETY ........................................................................2

INSTALLATION REQUIREMENTS .................................................2

Tools and Parts .............................................................................2

Location Requirements ................................................................3

Venting Requirements ..................................................................4

Venting Methods ..........................................................................5

Electrical Requirements ...............................................................7

INSTALLATION INSTRUCTIONS ...................................................8

Prepare Cooktop ..........................................................................8

Install Foam Strip .........................................................................9

Install Cooktop .............................................................................9

Make Electrical Connection .........................................................9

Complete Installation .................................................................10

SÉCURITÉ DE LA TABLE DE CUISSON .....................................11

EXIGENCES D’INSTALLATION ...................................................11

Outils et pièces ...........................................................................11

Exigences d’emplacement .........................................................12

Exigences concernant l’évacuation ...........................................13

Méthodes d’évacuation .............................................................14

Spéciﬁcations électriques ..........................................................16

INSTRUCTIONS D’INSTALLATION .............................................17

Préparation de la table de cuisson ............................................17

Installation de la bande de mousse ...........................................18

Installation de la table de cuisson ..............................................18

Raccordement électrique ...........................................................18

Achever l’installation ..................................................................19

IMPORTANT:

Save for local electrical inspector’s use.

IMPORTANT :

À conserver pour consultation par l’inspecteur local des installations électriques.

W10848428A

COOKTOP SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■ Tape measure

■ Flat-blade screwdriver

■ Phillips head screwdriver

■ Drill

■ Level

■ 6" socket extension

■ Marker or pencil

■ Pliers

■

/4" drill bit

■ Jigsaw

■ Ratchet with

■

/4" nut driver

/8" socket

Parts supplied

■ Vent grille

■ Pre-ﬁlter

■ Plenum

■ Plenum screw pack

■ Downdraft motor

assembly

■ Clamping brackets (2)

■ Bracket attachment

screws (2)

Parts needed

■ A UL Listed or CSA Approved strain relief for

knockout.

■ A UL Listed or CSA Approved conduit connector for

(1.3 cm) trade-size metal-clad conduit

■ UL Listed wire connectors

■ Metal ducting

■ Wall cap

6" (15.2 cm) Round Surface Wall Cap Damper Order Part Number A406

5" (12.7 cm) Round Surface Wall Cap Damper Order Part Number A405

31/4" x 10" (8.3 cm x 25.4 cm) Surface Wall Cap Damper Order Part Number A403

To order, see the “Assistance or Service” section of the Use and Care Guide.

■ Vent clamps

Check local codes. Check existing electrical supply. See the “Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualiﬁed electrical installer.

/8" (2.2 cm)

/2"

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. When installing cooktop, use minimum dimensions given.

■ To eliminate the risk of burns or ﬁre by reaching over the

heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■ Use the countertop opening dimensions that are given

with these Installation Instructions. Given dimensions are minimum clearances and provide 0" (0 cm) clearance.

■ Grounded electrical supply is required. See the “Electrical

Requirements” section.

■ If cabinet has drawers, drawers will need to be removed and

drawer fronts installed on front of cabinet.

IMPORTANT: An under-counter built-in oven cannot be installed under this product.

Product Dimensions

30" (76.2 cm) Cooktop – for standard and electric models

36" (91.4 cm) Cooktop – for standard and electric models

A. 203/4" (52.7 cm) screw head to screw head B. Model/serial rating/clearance plate location

C. 22

/16" (56.0 cm) without stainless steel trim or 221/2" (57.2 cm) or 23" (58.5 cm) with stainless steel trim (depending on model)

A. 221/16" (56.0 cm) without stainless steel trim or

221/2" (57.2 cm) or 23" (58.5 cm) with stainless steel trim (depending on model)

B. Model/serial rating/clearance plate location

C. 20

/4" (52.7 cm) screw head to screw head

A. 30 B. 12 C. 28 D. 14

/8" (78.4 cm)

/16" (31.0 cm)

/64" (72.3 cm)

/32" (37.4 cm)

E. 2" (5.1 cm) recommended minimum

cabinet to motor clearance

F. 18

/32" (47.6 cm)

G. 3

/32" (9.3 cm)

A. 36 B. 11 C. 34 D. 14

/16" (92.3 cm)

/32" (29.4 cm)

/64" (86.8 cm)

/32" (37.4 cm)

E. 2" (5.1 cm) recommended minimum

F. 18 G. 3

cabinet to motor clearance

/32" (47.6 cm)

/32" (9.3 cm)

Cabinet Dimensions

Cutout Dimensions

A. 30" (76.2 cm) on 30" (76.2 cm) models

36" (91.4 cm) on 36" (91.4 cm) models B. Combustible area above countertop (shown by dashed box above) C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of uncovered wood or metal cabinet (24" [61 cm]

minimum clearance if bottom of wood or metal cabinet is covered by

not less than

less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel,

0.024" [0.06 cm] aluminum, or 0.020" [0.05 cm] copper) D. 13" (33 cm) recommended upper cabinet depth E. 2" (5.1 cm)

F. 21

/8" (53.7 cm)

G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop

H. Junction box or outlet: 12" (30.5 cm) minimum from bottom

of countertop

I. Junction box or outlet; 10" (25.4 cm) from right-hand side of cabinet

J. 28

/8" (73.3 cm) on 30" (76.2 cm) models

349/16" (87.8 cm) on 36" (91.4 cm) models

K. 2

/2" (6.4 cm) minimum distance to nearest left and right side

combustible surface above cooktop

L. 1

/2" (3.8 cm) minimum clearance between back wall and countertop

/4" [0.6 cm] ﬂame retardant millboard covered with not

NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear the cooktop base. To avoid this modiﬁcation, use a base cabinet with sidewalls wider than the cutout.

■ A minimum side clearance of 6" (15.2 cm) is recommended

between side of cooktop and side wall for maximum ventilation performance.

■ A minimum clearance of 2" (5.1 cm) is recommended

between the motor/blower and cabinet for proper cooling. A 6" (15.2 cm) clearance is recommended for servicing access.

A. 287/8" (73.3 cm) maximum on 30" (76.2 cm) models

349/16" (87.8 cm) maximum on 36" (91.4 cm) models

B. 21

/8" (53.7 cm) maximum on both 30" (76.2 cm) and 36" (91.4 cm)

models

C. 8

/32" (21.8 cm) on 30" (76.2 cm) models

157/16" (39.2 cm) on 36" (91.4 cm) models

D. 6

/64" (16.0 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models E. 2" (5.1 cm) minimum space to front edge of cooktop F. Floor exhaust option

G. 6

/8" (15.6 cm) for 6" (15.2 cm) vent system

51/8" (13 cm) for 5" (12.7 cm) vent system

H. 8

/32" (21.8 cm) on 30" (76.2 cm) models

157/16" (39.2 cm) on 36" (91.4 cm) models I. 16" (40.6 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models J. Wall exhaust option

Venting Requirements

IMPORTANT: This cooktop must be exhausted outdoors unless using the Duct-Free Filter Accessory Kit. See the “Venting Methods” section.

■ Do not terminate the vent system in an attic or other

enclosed area.

■ Use a vent cap.

■ Vent system must terminate to the outside.

■ Use only a 6" (15.2 cm) diameter round or 3

(8.3 cm x 25.4 cm) rectangular vent except as follows: For electric cooktops, a 5" (12.7 cm) diameter round vent may be used for venting straight out the back of the cooktop and directly through the wall for 10 ft (3.0 m) or less.

■ Before making cutouts, make sure there is proper clearance

within the wall or ﬂoor for the exhaust vent.

■ Do not cut a joist or stud unless absolutely necessary. If a

joist or stud must be cut, then a supporting frame must be constructed.

■ The size of the vent should be uniform.

■ The vent system must have a damper. If roof or wall cap has

a damper, do not use damper supplied with the range hood.

■ Use vent clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around

the cap.

■ Determine which venting method is best for your application.

/4" x 10"

For Best Performance:

■ Use 26-gauge minimum galvanized or 25-gauge minimum

aluminum metal vent. Poor quality pipe ﬁttings can reduce airﬂow. Flexible metal vent is not recommended.

NOTE: Local codes may require a heavier gauge material.

■ Metal duct may be reduced to 30-gauge galvanized steel

or 26-gauge aluminized steel if allowed by local codes. This reduction is based on information in the International Residential Codes Section M1601.1 (2006 edition).

■ Do not install 2 elbows together.

■ Use no more than three 90° elbows.

■ If an elbow is used, install it as far away as possible from

the hood’s vent motor exhaust opening.

■ Make sure there is a minimum of 18" (45.7 cm) of straight

vent between the elbows if more than one elbow is used.

■ Elbows too close together can cause excess turbulence that

reduces airﬂow.

■ Do not use a 5" (12.7 cm) elbow in a 6" (15.2 cm) or 3

/4" x 10"

(8.3 cm x 25.4 cm) system.

■ Do not reduce to a 5" (12.7 cm) system after using

6" (15.2 cm) or 31/4" x 10" (8.3 cm x 25.4 cm) ﬁttings.

■ Avoid forming handmade crimps. Handmade crimps may

restrict airﬂow.

■ Use a vent cap for proper performance. If an alternate wall

or roof cap is used, be certain the cap size is not reduced and that it has a backdraft damper.

■ Use vent clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around

the cap.

The length of vent system and number of elbows should be kept to a minimum to provide efﬁcient performance.

The maximum equivalent length of the vent system is 60 ft (18.3 m). For altitudes above 4,500 ft (1372 m), reduce recommended vent run by 20% for best performance.

Cold Weather Installations

An additional backdraft damper should be installed to minimize backward cold air ﬂow.

Makeup Air

Local building codes may require the use of makeup air systems when using ventilation systems greater than speciﬁed CFM of air movement. The speciﬁed CFM varies from locale to locale. Consult your HVAC professional for speciﬁc requirements in your area.

Venting Methods

Common venting methods are shown for a counter-mounted downdraft cooktop. The cooktop may be vented through the wall or ﬂoor.

Option 1 – Roof Venting Option 2 – Wall Venting

A. 6" (15.2 cm) round roof venting B. Roof cap

Option 3 – Venting

Between Floor Joists

A. Wall cap B. 6" (15.2 cm) round wall venting

A. 6" (15.2 cm) round wall venting B. Wall cap

Option 4 – Venting Behind

Cabinet Kick Plate

3¼" x 10"

(8.3 cm x 25.4 cm)

A. Wall cap B. 6" (15.2 cm) round wall venting

Concrete Slab Installations – Exhaust Through Wall

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft

(0.8 m)

A. Wall cap B. 6" (15.2 cm) round metal vent C. 16" (40.6 cm) maximum D. 6" (15.2 cm) round PVC sewer

pipe E. 6" (15.2 cm) round metal duct F. 6" (15.2 cm) round

PVC coupling G. Concrete slab H. 6" (15.2 cm) round PVC

sewer pipe

I. 6" (15.2 cm) round 90° PVC

sewer pipe elbow

J. Tightly pack gravel or sand

completely around pipe. K. 30 ft (9.1 m) max. L. 6" (15.2 cm) round 90° PVC

sewer pipe elbow M. 6" (15.2 cm) round PVC

coupling N. 12" (30.5 cm) minimum

Duct-Free Filter Accessory Kit

On select downdraft models, the Duct-Free Filter Accessory Kit Part Number JDA7000WX is now available. Duct-Free Filter Accessory Kit is ideal for both new construction and kitchen renovation projects because it provides an easy alternative to the installation of metal ducting and venting in the downdraft system outside the home. The kit includes all required hardware, one ﬁlter and complete installation instructions.Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

90° elbow 5.0 ft

(1.5 m)

6" (15.2 cm) wall cap 0.0 ft

(0.0 m)

31/4" x 10" (8.3 cm x 25.4 cm) to 6" (15.2 cm) transition

6" (15.2 cm) to 31/4" x 10" (8.3 cm x 25.4 cm) transition

31/4" x 10" (8.3 cm x 25.4 cm) to 6" (15.2 cm) 90° elbow transition

6" (15.2 cm) to 31/4" x 10" (8.3 cm x 25.4 cm) 90° elbow transition

4.5 ft (1.4 m)

1 ft (0.3 m)

5.0 ft (1.5 m)

31/4" x 10" (8.3 cm x 25.4 cm) 90° elbow

31/4" x 10" (8.3 cm x 25.4 cm) ﬂat elbow

31/4" x 10" (8.3 cm x 25.4 cm) wall cap

5.0 ft (1.5 m)

12.0 ft (3.7 m)

0.0 ft (0.0 m)

+ 14 hidden pages