Jenn-Air CCG456B, CCG456W, CCG457B, CCG457W, CCP457B Dimension Guide
...
www.dexpress.com DIMENSION EXPRESS Fax on Demand (775) 833-3600
This Data Sheet Includes Information On
Jenn-Air
• Product Model Number (s): •
CCG456B, CCG457W, CCG457B, CCP457W and
• Dimensions (Actual Size) •
Distance from top of counter to bottom of unit:
Min. spacing from cooktop edge to nearest
vertical combustible wall to the RIGHT:
Min. spacing from cooktop edge to nearest
vertical combustible wall to the LEFT:
Min. spacing from cooktop edge to nearest
vertical combustible wall to the REAR:
Minimum spacing to front edge of counter:
Minimum distance between cooktop
Minimum width of cabinet directly above:
Maximum depth of cabinets directly
Minimum distance between countertop
• Additional Information •
• Electrical requirements : 110/120 volt AC, 60hz. Must
be grounded. 15amp circuit required. Locate outlet
below the cooktop a minimum of 3" below the
countertop if not installing over an under counter oven.
Locate outlet below the oven or in an adjacent cabinet
when installing over an adjacent under counter oven.
• Minimum clearance from top of counter to combustible
material below is 2 5/8"
• Countertop must be supported within 3" of cutout.
• Unit may be installed over an under counter oven.
• Gas requirements : The pressure regulator supplied
with this appliance is pre-set and fixed for correct
outlet pressure: 5"W.C. if this model is equipped for
use with natural gas (models CCG456B and CCG457W,
CCG457B); 10" W.C. if equipped for use with LP
(models CCP457W and CCP457B). The maximum inlet
gas supply pressure for the regulator is 14" W.C. The
inlet test pressure for checking the regulator must be
at least 6" W.C if equipped for natural gas; 11" W.C. if
equipped for LP gas.
30" Gas Cooktops:
CCP457B
Overall width:
Overall depth:
Cut-Out width:
Cut-Out depth:
and cabinet directly above:
above and adjacent:
and adjacent cabinet above:
26 9/16"
20 1/16"
30"
21"
2 5/8"
2"
2"
1 1/2"
2"
30"
30"
13"
18"
2 5/8"
Side View (not to scale)
20 1/16"
26 9/16"
30"
18"
REAR View
(not to scale)
Underside of counter may have to be
modified to accept gas pipe.
30"
21"
Overall Dimensions
Top View (not to scale)
Cut-Out Dimensions
Countertop View
(not to scale)
Cabinet Requirements
Wall View
(not to scale)
30"
Minimum horizontal
clearance between the
edge of the appliance
and combustible
construction extending
from the cooking
surface to 18" above
the cooking surface is
2" (see solid areas)
1 5/8"
From countertop to
centerline of
manifold
See page 2 for additional information
Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2000.
• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
321
Manifold entrance
BN183 • A321B149 • 31469 • 002906 • 13243 • 12123
2 27/32"
From cutout edge to
centerline of manifold
www.dexpress.com
DIMENSION EXPRESS
Fax on Demand (775) 833-3600
Additional Information:
• An individual gas shut-off valve must be used.
• Cabinetry over cooktop : 30' minimum clearance between the top of
the cooking surface and the bottom of an unprotected wood or metal
cabinet. 24" minimum when bottom of wood or metal cabinet is
protected by not less than 1/4" flame retardant millboard covered with
not less than no. 28 MSG sheet steel, 0.015" stainless steel, 0.024"
aluminum or copper.
• To eliminate the hazard of reaching over heated surface units,
cabinet storage space located above the surface units should be
avoided. If cabinet storage is to be provided, the hazard can be
reduced by installing a range hood that projects horizontally a
minimum of 5" beyond the bottom of the cabinets.
• Radius corners of cutout and file to insure smooth edges and prevent
corner cracking (1/4" radius).
• CCG456B : Black, Natural gas.
• CCG457B : Black, Natural gas.
• CCG457W : White, Natural gas.
• CCP457W : White, LP gas.
• CCP457B : Black, LP gas.
Page 2
This Data Sheet Includes Information On
Jenn-Air
• Product Model Number (s): •
30" Gas Cooktops:
CCG456B, CCG457W, CCG457B, CCP457W and
CCP457B
Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2000.
• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
BN183 • A321B149 • 31469 • 002906 • 13243 • 12123
149
Loading...