Jeep Grand Cherokee 2015 Owner's Manual

2015
OWNER’S MANUAL
Grand Cherokee
SRT
With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore.
DRIVING AND ALCOHOL
Drunken driving is one of the most frequent causes of accidents.
Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non­drinking driver, call a cab, a friend, or use public trans­portation.
WARNING!
Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.
This manual illustrates and describes the operation of features and equipment that are either standard or op­tional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.
FCA US LLC reserves the right to make changes in design and specifications, and/or make additions to or improve­ments to its products without imposing any obligation upon itself to install them on products previously manu­factured.
Jeep is a registered trademark of FCA US LLC
Copyright © 2015 FCA US LLC
SECTION PAGE
INTRODUCTION . ..............................................................3
1
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .................................11
2
UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . ..............................113
3
UNDERSTANDING YOUR INSTRUMENT PANEL ......................................281
4
STARTINGANDOPERATING ....................................................395
5
TABLE OF CONTENTS
1
2
3
4
5
WHATTODOINEMERGENCIES..................................................499
6
MAINTAININGYOURVEHICLE...................................................525
7
MAINTENANCE SCHEDULES ....................................................595
8
IF YOU NEED CONSUMER ASSISTANCE ............................................603
9
INDEX .....................................................................613
10
6
7
8
9
10

INTRODUCTION

CONTENTS
INTRODUCTION ........................4
1
WARNINGS AND CAUTIONS ..............8
ROLLOVER WARNING ...................5
HOW TO USE THIS MANUAL ..............6
VEHICLE IDENTIFICATION NUMBER ........8
VEHICLE MODIFICATIONS/ALTERATIONS ....9
4 INTRODUCTION

INTRODUCTION

Congratulations on selecting your new FCA US LLC vehicle. Be assured that it represents precision workman­ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
This is a specialized utility vehicle. It can go places and perform tasks that conventional passenger cars are not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle.
The two-wheel drive version of this vehicle was designed for on-road use only. It is not intended for off-road driving or use in other severe conditions suited for a four-wheel drive vehicle.
Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering, transmis­sion, and transfer case shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. When driving off-road or working the vehicle, don’t overload the vehicle or expect the vehicle to overcome the natural laws of physics. Always observe federal, state, provincial and local laws wherever you drive.
As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or a collision. Refer to “On-Road/Off-Road Driving Tips” in “Starting And Operating” for further information.
This Owner’s Manual has been prepared with the assis­tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents. Please take the time to read these publications carefully. Following the instruc­tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
NOTE: After reviewing the owner information, it should be stored in the vehicle for convenient referenc­ing and remain with the vehicle when sold.
When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech­nicians and genuine MOPAR® parts, and cares about your satisfaction.
INTRODUCTION 5

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.
Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully.
1
6 INTRODUCTION
two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.
Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment.
Rollover Warning Label
Failure to use the driver and passenger seat belts pro­vided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by
The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:
INTRODUCTION 7
1
8 INTRODUCTION

WARNINGS AND CAUTIONS

This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce­dures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information. Observe all Warnings and Cau­tions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on a plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also is stamped into the right front body, behind the right front seat. Move the right front seat forward to allow better viewing of the stamped VIN. This number also appears on the Automobile Infor­mation Disclosure Label affixed to a window on your
vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
VIN Location
Right Front Body VIN Location
NOTE: It is illegal to remove or alter the VIN.
INTRODUCTION 9

VEHICLE MODIFICATIONS/ALTERATIONS

1
WARNING!
Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS
A WORD ABOUT YOUR KEYS .............13
To Arm The System ....................20
2
Keyless Ignition Node (KIN) ..............13
KeyFob.............................15
Ignition Or Accessory On Message ..........16
SENTRY KEY® .........................17
Replacement Keys .....................18
Customer Key Programming ..............19
General Information ....................19
VEHICLE SECURITY ALARM — IF EQUIPPED . . .19
Rearming The System ...................20
To Disarm The System ...................21
Tamper Alert .........................22
ILLUMINATED ENTRY — IF EQUIPPED ......22
REMOTE KEYLESS ENTRY (RKE) ...........22
To Unlock The Doors And Liftgate ..........23
To Lock The Doors And Liftgate ............24
Using The Panic Alarm ..................25
Programming Additional Transmitters .......26
Transmitter Battery Replacement ...........26
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
General Information ....................27
OCCUPANT RESTRAINT SYSTEMS ..........49
REMOTE STARTING SYSTEM — IF EQUIPPED . .28
How To Use Remote Start ................28
DOOR LOCKS .........................31
Power Door Locks .....................33
Child-Protection Door Lock System — Rear
Doors ..............................34
KEYLESS ENTER-N-GO™ .................36
WINDOWS ...........................41
Power Windows .......................41
Wind Buffeting .......................45
LIFTGATE ............................45
Power Liftgate — If Equipped .............47
Important Safety Precautions ..............50
Seat Belt Systems ......................51
Supplemental Restraint System (SRS) ........67
Child Restraints .......................82
Transporting Pets .....................106
SRT ENGINE BREAK-IN RECOMMENDATIONS . .106
SAFETY TIPS .........................107
Transporting Passengers .................107
Exhaust Gas .........................108
Safety Checks You Should Make Inside The
Vehicle .............................109
Periodic Safety Checks You Should Make Outside
The Vehicle .........................111

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Keyless Ignition Node (KIN).
Keyless Enter-N-Go™ Feature
This vehicle is equipped with the Keyless Enter-N-Go™ feature. Refer to Keyless Enter-N-Go™in Things To Know Before Starting Your Vehiclefor further informa­tion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

Keyless Ignition Node (KIN)

This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment.
The Keyless Ignition Node (KIN) has four operating positions; three of which are labeled and will illuminate when in position. The three positions are OFF, ACC, and ON/RUN. The fourth position is START, during start RUN will illuminate.
2
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: In case the ignition switch does not change with the push of a button, the RKE transmitter (Key Fob) may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the Key Fob against the ENGINE START/STOP button and push to operate the ignition switch.
Keyless Ignition Node (KIN)

Key Fob

The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob.
The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead. The emergency key is also for locking the glove box. You can keep the emergency key with you when valet park­ing.
To remove the emergency key, slide the mechanical latch at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
2
Emergency Key Removal
NOTE: You can insert the double-sided emergency key
into the lock cylinders with either side up.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Ignition Or Accessory On Message

Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster.
NOTE: With the Uconnect® system, the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is placed in the OFF position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information.
WARNING!
When leaving the vehicle, always remove the Key Fob from the vehicle and lock your vehicle.
Never leave children alone in a vehicle, or with access to an unlocked vehicle.
Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil­dren should be warned not to touch the parking brake, brake pedal or the gear selector.
Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
(Continued)
WARNING! (Continued)
Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
CAUTION!
An unlocked car is an invitation to thieves. Always remove the Key Fob from vehicle, place the ignition in the OFF and lock all doors when leaving the vehicle unattended.

SENTRY KEY®

The Sentry Key® Immobilizer System prevents unau­thorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
The system uses a Key Fob with a factory-mated Remote Keyless Entry (RKE) transmitter, an Ignition Node Mod­ule, Keyless Ignition Node (KIN) and a RF receiver to prevent unauthorized vehicle operation. Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine to crank if an invalid Key Fob is used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid Key Fob is used to start the engine.
NOTE: A Key Fob that has not been programmed is also considered an invalid key.
During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid
2
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Key Fob to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds.
If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electron­ics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.
CAUTION!
The Sentry Key® Immobilizer system is not compat­ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
All of the Key Fobs provided with your new vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only Key Fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle.
CAUTION!
Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unat­tended.
For vehicles equipped with Keyless Enter-N-Go™, always remember to place the ignition in the OFF position.
NOTE: Duplication of Key Fobs may be performed at an
authorized dealer. This procedure consists of program­ming a blank Key Fob to the vehicle electronics. A blank Key Fob is one that has never been programmed.
When having the Sentry Key® Immobilizer System ser­viced, bring all vehicle keys with you to an authorized dealer.

Customer Key Programming

Programming Key Fobs or RKE transmitters may be performed at an authorized dealer.

General Information

The Sentry Key® system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:
This device may not cause harmful interference.
This device must accept any interference that may be
received, including interference that may cause unde­sired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

VEHICLE SECURITY ALARM — IF EQUIPPED

This Vehicle Security Alarm monitors the vehicle doors, liftgate, and ignition for unauthorized operation. When the alarm is activated, the interior switches for door locks, and power liftgate are disabled. The Vehicle Secu­rity Alarm provides both audio and visual signals; the horn will sound, the headlights will turn on, park lamps and/or turn signals will flash repeatedly for three min­utes. If the disturbance is still present (driver’s door, passenger door, other doors, ignition) after three minutes, the headlights, park lamps and/or turn signals will flash for an additional 15 minutes.
2
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: The Panic and Security alarms are quite different. Please take a moment to activate the Panic and the Security modes to hear the differences in the horn. In case one should go off in the future, you will need to know which mode has been activated in order to deactivate it.

Rearming The System

If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the Vehicle Security Alarm will rearm itself.

To Arm The System

Follow these steps to arm the Vehicle Security Alarm:
1. Make sure the vehicles ignition is cycled to the “OFF”
position (refer to Starting Proceduresin Starting And Operatingfor further information).
For vehicles equipped with Keyless Enter-N-Go™, make sure the vehicle ignition system is OFF.
For vehicles not equipped with Keyless Enter-N­Go™, make sure the vehicle ignition system is OFF, and the key is physically removed from the ignition.
2. Perform one of the following methods to lock the vehicle:
Push LOCK on the interior power door lock switch with the driver and/or passenger door open.
Push the LOCK button on the exterior Passive Entry Door Handle with a valid Key Fob available in the same exterior zone (refer to Keyless Enter-N-Go™ in Things To Know Before Starting Your Vehiclefor further information).
Push the LOCK button on the Remote Keyless Entry (RKE) transmitter.
3. If any doors are open, close them.

To Disarm The System

The Vehicle Security Alarm can be disarmed using any of the following methods:
Push the UNLOCK button on the Remote Keyless Entry (RKE) transmitter.
Grasp the Passive Entry Unlock Door Handle (refer to Keyless Enter-N-Go™in Things To Know Before Starting Your Vehiclefor further information).
Cycle the vehicle ignition system out of the OFF position.
NOTE:
The driver’s door key cylinder and the liftgate button on the RKE transmitter cannot arm or disarm the Vehicle Security Alarm.
The Vehicle Security Alarm remains armed during power liftgate entry. Pushing the LIFTGATE button
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
will not disarm the Vehicle Security Alarm. If someone enters the vehicle through the liftgate and opens any door, the alarm will sound.
When the Vehicle Security Alarm is armed, the interior power door lock switches will not unlock the doors.
The Vehicle Security Alarm is designed to protect your vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previ­ously described arming sequences has occurred, the Vehicle Security Alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm.
If the Vehicle Security Alarm is armed and the battery becomes disconnected, the Vehicle Security Alarm will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound. If this occurs, disarm the Vehicle Security Alarm.
2
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Tamper Alert

If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times, and the exterior lights blink three times when you unlock the doors. Check the vehicle for tampering.

ILLUMINATED ENTRY — IF EQUIPPED

The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door.
This feature also turns on the approach lighting in the outside mirrors (if equipped).
The lights will fade to off after approximately 30 seconds, or they will immediately fade to off once the ignition is placed in the ON/RUN position from the OFF position.
NOTE:
The front courtesy overhead console and door cour­tesy lights will turn on if the dimmer control is in the “Dome ON” position (extreme top position).
The Illuminated Entry system will not operate if the dimmer control is in the “Dome defeat” position (extreme bottom position).

REMOTE KEYLESS ENTRY (RKE)

The RKE system allows you to lock or unlock the doors, open the power liftgate, remote start your vehicle (if equipped), or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.
NOTE: Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all RKE transmit­ter buttons for all RKE transmitters.
Keyless Enter-N-Go™ Fob
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

To Unlock The Doors And Liftgate

Push and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go™” in “Things To Know Before Starting Your Vehicle” for further information.
1st Press Of Key Fob Unlocks
This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the UNLOCK button on the RKE transmitter. To change the current setting, refer to “Uconnect® Settings” in “Under­standing Your Instrument Panel” for further information.
2
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Flash Lamps With Lock
This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmit­ter. This feature can be turned on or turned off. To change the current setting, refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further in­formation.
REMOTE STARTING SYSTEM — IF EQUIPPED
This feature allows the Remote Keyless Entry (RKE) transmitter to start the engine conve­niently from outside the vehicle while still maintaining security. The system has a range of
approximately 300 ft (91 m).
Headlight Illumination On Approach
This feature activates the headlights for up to 90 seconds when the doors are unlocked with the RKE transmitter. The time for this feature is programmable on vehicles equipped through Uconnect®. To change the current setting, refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information.
NOTE:
The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.
Obstructions between the vehicle and the RKE trans­mitter may reduce this range.

To Lock The Doors And Liftgate

Push and release the LOCK button on the RKE transmit­ter to lock all doors and liftgate. The turn signal lights will flash, and the horn will chirp to acknowledge the signal.
If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go™” in “Things To Know Before Starting Your Vehicle” for further information.
Sound Horn With Lock
This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information.

Using The Panic Alarm

To turn the Panic Alarm feature on or off, push and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is activated, the turn signals will flash, the horn will pulse on and off, and the interior lights will turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
The Panic Alarm will stay on for three minutes unless you turn it off by either pushing the PANIC button a second time or drive the vehicle at a speed of 15 MPH (24 km/h) or greater.
NOTE:
The interior lights will turn off if you place the ignition in the ACC or ON/RUN position while the Panic Alarm is activated. However, the exterior lights and horn will remain on.
You may need to be less than 35 ft (11 m) from the vehicle when using the RKE transmitter to turn off the Panic Alarm due to the radio frequency noises emitted by the system.
2
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Programming Additional Transmitters

Programming Key Fobs or RKE transmitters may be performed at an authorized dealer.

Transmitter Battery Replacement

The recommended replacement battery is one CR2032 battery.
NOTE:
Perchlorate Material — special handling may apply. Batteries could contain dangerous materials. Please dispose of them according to respect for environment and local laws.
Used batteries are harmful to the environment. You can dispose of them either in the correct containers as specified by law or by taking them to a Dealership, which will deal with their disposal.
Do not touch the battery terminals that are on the back housing or the printed circuit board.
1. Remove the emergency key by sliding the mechanical
latch on the back of the RKE transmitter sideways with your thumb and then pull the key out with your other hand.
2. Insert the tip of the emergency key or a #2 flat blade
screwdriver into the slot and gently pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
Separating RKE Transmitter Case
3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.
4. To assemble the RKE transmitter case, snap the two halves together.

General Information

This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions:
This device may not cause harmful interference.
This device must accept any interference received,
including interference that may cause undesired op­eration.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
If your RKE transmitter fails to operate from a normal distance, check for these two conditions:
1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years.
2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.

REMOTE STARTING SYSTEM — IF EQUIPPED

NOTE:
The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.
Obstructions between the vehicle and the RKE trans­mitter may reduce this range.

How To Use Remote Start

All of the following conditions must be met before the engine will remote start:
This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve­niently from outside the vehicle while still maintaining security. The system has a range of
approximately 300 ft (91 m).
Shift lever in PARK
Doors closed
Hood closed
HAZARD switch off
BRAKE switch inactive (brake pedal not pressed)
Battery at an acceptable charge level
Loading...
+ 606 hidden pages