Jeep 2018 WRANGLER Quick Reference Manual

2018 JEEP® WRANGLER QUICK REFERENCE GUIDE

ALL NEW

VEHICLE USER GUIDE — IF
EQUIPPED

Vehicle User Guide

Access your Owner’s Information – right
through your Uconnect 4C or 4C NAV touch­screen radio — If Equipped.

To access the Vehicle User Guide on your
Uconnect Touchscreen: Push the Uconnect
Apps button, then push the Vehicle User Guide
icon on your touchscreen. No Uconnect regis­tration is required.

NOTE:

Vehicle User Guide features are not available
while the vehicle is moving. If you try to access
while the vehicle is in motion, the system
displays: Feature not available while the vehicle
is in motion.

Pre-Installed Features

• Your User Guide
— Updated in
real-time

• Touchscreen
convenience

• Maintenance
schedules and
information

• Comprehensive
icon & symbol
glossary

• Available when
and where you
need it

• Customizable
interface

• Multilingual

KEYLESS ENTER-N-GO —
PASSIVE ENTRY

Introduction To Keyless
Enter-N-Go

The Keyless Enter-N-Go — Passive Entry sys­tem is an enhancement to the vehicle’s key fob.
This feature allows you to lock and unlock the
vehicle’s door(s) without having to push the key
fob lock or unlock buttons as well as starting
and stopping the vehicle with the push of a
button.

Vehicle User Guide Touchscreen Icon

NOTE:

Uconnect screen images are for illustration
purposes only and may not reflect exact soft­ware for your vehicle.

To Lock The Vehicle’s Doors

With a valid Keyless Enter-N-Go key fob within
5 ft (1.5 m) of the driver or passenger front door
handles, push door handle lock button to lock
all doors.

Do NOT grab the door handle, when pushing
the door handle lock button. This could unlock
the door(s).

Push The Button To Lock

NOTE:

• After pushing the door handle lock button,
you must wait two seconds before you can
lock or unlock the doors, using either Passive
Entry door handle. This is done to allow you
to check if the vehicle is locked by pulling
the door handle without the vehicle reacting
and unlocking.

• The Passive Entry system will not operate if
the key fob battery is dead.

The vehicle doors can also be locked by using
the key fob lock button or the lock button
located on the vehicles interior door panel.

Do NOT Grab The Handle When Locking

To Unlock From The Driver Or
Passenger Side

Grab The Door Handle To Unlock

With a valid Keyless Enter-N-Go key fob located
outside the vehicle and within 5 ft (1.5 m) of
the driver or passenger side door handle, grab
either front door handle to unlock the door
automatically.

For further information, and applicable warn­ings and cautions, please refer to the Owner’s
Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).

To Unlock/Lock The Swing Gate

To Unlock/Enter The Swing Gate

The Swing Gate passive entry unlock feature is
built into handle of the Swing Gate. With a valid
Passive Entry key fob within 5 ft (1.5 m) of the
Swing Gate, pull the Swing Gate handle to open
with one fluid motion.

Swing Gate Passive Entry Location

DOORS

To Lock The Swing Gate

With a valid Passive Entry key fob within 5 ft
(1.5 m) of the Swing Gate, push the passive
entry lock button located on the outside Swing
Gate door handle.

NOTE:

The Swing Gate passive entry lock button will
lock all doors and the Swing Gate. The Swing
Gate unlock feature is built into the Swing Gate
handle.

Front Door Removal

Door Removal Warning Label

NOTE:

• Doors are heavy; use caution when removing
them.

• Hinge pin can break if overtightened during
door reinstall (Max Torque: 7.5 ft· lb / 10 N·m).

1. Roll down the glass window to prevent any
damage.

2. Remove the hinge pin screws from the upper
and lower outside hinges (using a #T50 Torx
head driver).

NOTE:

The hinge pin screws and nuts can be stowed
in the rear cargo tray located under the rear
loadfloor.

Hinge Pin Screw

3. Remove the plastic wiring access door under
the instrument panel by sliding the plastic
panel along the door frame toward the seats
until the tabs are detached.

Wiring Access Door

NOTE:

Do not pry back to open, as this will break the
plastic cover.

4. Pull up on the red locking tab to unlock the
wiring harness.

Closed Wiring Harness

1 – Locking Tab
2 – Wiring Harness

5. Push and hold down the black security tab
under the wiring harness, and lift the har­ness into the open position.

6. With the wiring harness open, pull down­ward on the wiring connector to unplug.
Store wiring connector in the lower door
basket.

7. Remove the check screw from the center
door check (using a #T40 Torx head driver).

Door Check

8. With the door open, lift the door with the
help of another person, to clear the hinge
pins from their hinges and remove the door.

To reinstall the door(s), perform the previous
steps in the opposite order.

NOTE:

The upper hinge has a longer pin, which can be
used to assist in guiding the door into place
when reinstalling.

Rear Door Removal (Four-Door
Models)

Door Removal Warning Label

NOTE:

• Doors are heavy; use caution when removing
them.

• Hinge pin can break if overtightened during
door reinstall (Max Torque: 7.5 ft· lb / 10 N·m).

1. Roll down the glass window to prevent any
damage.

2. Remove the hinge pin screws from the upper
and lower outside hinges (using a #T50 Torx
head driver).

NOTE:

The hinge pin screws and nuts can be stowed in
the rear cargo tray located under the rear load
floor.

3. Slide the front seat(s) fully forward.

4. Pry open and remove the plastic wiring ac­cess door from the bottom of the B-pillar.

5. Unplug the wiring connector.

SEATS

NOTE:

Squeeze the tab on the base of the wiring
harness. This will unlock the connector tab,
allowing the wiring connector to be unplugged.

Wiring Connector

6. Remove the check screw from the center
door check (using a #T40 Torx head driver).

7. With the door open, lift the door with the
help of another person, to clear the hinge
pins from their hinges and remove the door.

To reinstall the door(s), perform the previous
steps in the reverse order.

NOTE:

The upper hinge has a longer pin, which can be
used to assist in guiding the door into place
when reinstalling.

For further information, and applicable warn­ings and cautions, please refer to the Owner’s
Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).

Easy Entry Seat — Two Door
Models

Pull upward on the easy entry lever located on
the outboard side of the seat back, and slide the
entire seat forward.

Easy Entry Lever

To return the seat to a sitting position, fold the
seatback upright until it locks and push the
seat rearward until the track locks.

Fold And Tumble Rear Seat —
Two Door Models

Folding The Rear Seat

1. Lift the seatback release lever, located on
the seatback between the head restraints,
and fold the seatback forward.

2. Slowly flip the entire seat forward.

3. Use the two retention straps located on the
back of the rear seat and two corresponding
wire loops located on the back of each
b-pillar, and thread the hook-and-loop fas­teners on the straps through the loops to
secure the seat in the folded position.

Folding Rear Seat — Four Door
Models

To fold the seat, lift upward on the seatback
release lever, located on the outboard sides of
the rear seat, and slowly fold down the seat­back. The head restraint will fold automatically
with the seat when this lever is pulled.

Rear Seat Tumble Position Retention Strap

For further information, and applicable warn­ings and cautions, please refer to the Owner’s
Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).

Seatback Release Lever

1 — Seatback Release Lever
2 — Head Restraint Release Lever

STARTING AND OPERATING

Four–Wheel Drive Operation

Four And Five Position Transfer Case

Four Position Four-Wheel Drive Gear Selector

The transfer case provides the following mode
positions:

2H

Rear Wheel Drive High Range — This range is
for normal street and highway driving on dry,
hard surfaced roads.

4H AUTO — If Equipped

Four-Wheel Drive Auto High Range — This
range sends power to the front wheels. The
four-wheel drive system will be automatically
engaged when the vehicle senses a loss of
traction. Additional traction for varying road
conditions.

Five Position Four-Wheel Drive Gear Selector

4H / 4H PART TIME (P-T)

Four-Wheel Drive High Range — This range
maximizes torque to the front driveshaft, forc­ing the front and rear wheels to rotate at the
same speed. This range provides additional
traction for loose, slippery road surfaces only.

NEUTRAL (N)

Neutral — This range disengages both the front
and rear driveshafts from the powertrain. To be
used for flat towing behind another vehicle.
Refer to “Recreational Towing” in “Starting
And Operating” in your Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Ca­nadian Residents) for further information.

4L

Four-Wheel Drive Low Range — This range
provides low speed four-wheel drive. It maxi­mizes torque to the front driveshaft, forcing the
front and rear wheels to rotate at the same

speed. This range provides additional traction
and maximum pulling power for loose, slippery
road surfaces only. Do not exceed 25 mph
(40 km/h).

This transfer case is designed to be driven in
the two-wheel drive position (2WD) or four­wheel drive position (4WD AUTO) for normal
street and highway conditions on dry hard sur­faced roads). Driving the vehicle in 2WD will
have greater fuel economy benefits as the front
axle is not engaged in 2WD.

For variable driving conditions, the 4WD AUTO
mode can be used. In this mode, the front axle
is engaged, but the vehicle's power is sent to
the rear wheels. Four-wheel drive will be auto­matically engaged when the vehicle senses a
loss of traction. Because the front axle is en­gaged, this mode will result in lower fuel
economy than the 2WD mode.

In the event that additional traction is required,
the transfer case 4H, 4H P-T and 4L positions
can be used to lock the front and rear drive­shafts together, forcing the front and rear
wheels to rotate at the same speed. The 4H, 4H

P-T and 4L positions are intended for loose,
slippery road surfaces only and not intended for
normal driving. Driving in the 4H, 4H P-T and
4L positions on hard-surfaced roads will cause
increased tire wear and damage to the driveline
components. Refer to “Shifting Procedures” in
this section for further information on shifting
into 4H, 4H P-T or 4L.

When operating your vehicle in 4L, the engine
speed will be approximately three times (four
times for Rubicon models) that of the 2H, 4H,
or 4H P-T positions at a given road speed. Take
care not to overspeed the engine.

Shifting Procedures

2H To 4H/4H Auto Or 4H/4H Auto To 2H

Shifting between 2H and 4H/4H Auto can be
made with the vehicle stopped or in motion. The
preferred shifting speed would be 0 to 45 mph
(72 km/h). With the vehicle in motion, the trans­fer case will engage/disengage faster if you mo­mentarily release the accelerator pedal after
completing the shift. Do not accelerate while
shifting the transfer case. Apply a constant force
when shifting the transfer case lever.

2H To 4H / 4H (P-T) / 4H Auto Or 4H / 4H (P-T) / 4H
Auto To 2H

With the vehicle rolling at 2 to 3 mph (3 to
5 km/h), shift an automatic transmission into
NEUTRAL (N), or press the clutch pedal on a
manual transmission. While the vehicle is
coasting at 2 to 3 mph (3 to 5 km/h), shift the
transfer case lever firmly to the desired posi­tion. Do not pause with the transfer case in N
(Neutral). Once the shift is completed, place
the automatic transmission into DRIVE or re­lease the clutch pedal on a manual
transmission.

WARNING!

Failure to engage a transfer case position
completely can cause transfer case damage
or loss of power and vehicle control. You
could have a collision. Do not drive the
vehicle unless the transfer case is fully en­gaged.

2H/4H Auto To 4H Part Time Or 4H Part Time To
2H/4H Auto

Shifting between 2H/4H AUTO to 4H PART
TIME can be made with the vehicle stopped or
in motion. The preferred shifting speed would
be 0 to 45 mph (72 km/h). With the vehicle in
motion, the transfer case will engage/disengage
faster if you momentarily release the accelera­tor pedal after completing the shift. Do not
accelerate while shifting the transfer case. Ap­ply a constant force when shifting the transfer
case lever.

4H Part Time/4H Auto To 4L Or 4L To 4H Part
Time/4H Auto

With the vehicle rolling at 2 to 3 mph (3 to
5 km/h), shift an automatic transmission into
NEUTRAL (N), or press the clutch pedal on a
manual transmission. While the vehicle is coast­ing at 2 to 3 mph (3 to 5 km/h), shift the transfer
case lever firmly to the desired position. Do not
pause with the transfer case in N (Neutral). Once
the shift is completed, place the automatic trans­mission into DRIVE or release the clutch pedal on
a manual transmission.

NOTE:

• Shifting into or out of 4L is possible with the
vehicle completely stopped; however, diffi­culty may occur due to the mating teeth not
being properly aligned. Several attempts
may be required for clutch teeth alignment
and shift completion to occur. The preferred
method is with the vehicle rolling at 2 to
3 mph (3 to 5 km/h). Avoid attempting to
engage or disengage 4L with the vehicle
moving faster than 2 to 3 mph (3 to 5 km/h).

• Do not attempt to make a shift while only the
front or rear wheels are spinning. The front
and rear driveshaft speeds must be equal for
the shift to take place. Shifting while only
the front or rear wheels are spinning can
cause damage to the transfer case.

• Delayed shifts out of four-wheel drive may be
experienced due to uneven tire wear, low or
uneven tire pressures, excessive vehicle
loading, or cold temperatures.

• Shifting effort will increase with speed, this
is normal.

During cold weather, you may experience in­creased effort in shifting until the transfer case
fluid warms up. This is normal.

Sway Bar Disconnect

Your vehicle may be equipped with an elec­tronic disconnecting stabilizer/sway bar. This
system allows greater front suspension travel in
off-road situations.

This system is controlled by the SWAY BAR
switch located on the instrument panel (to the
right of the steering column).

Sway Bar Switch

Push the SWAY BAR switch to activate the
system. Push the switch again to deactivate the
system. The “Sway Bar Indicator Light” (lo­cated in the instrument cluster) will illuminate
when the bar is disconnected. The “Sway Bar
Indicator Light” will flash during activation
transition, or when activation conditions are not
met. The stabilizer/sway bar should remain in
on-road mode during normal driving conditions.

To disconnect the stabilizer/sway bar, shift to
either 4H or 4L and push the SWAY BAR switch
to obtain the off-road position. Refer to “Four­Wheel Drive Operation” in this section for fur­ther information. The “Sway Bar Indicator
Light” will flash until the stabilizer/sway bar
has been fully disconnected.

To return to on-road mode, push the SWAY BAR
switch again.

For further information, and applicable warn­ings and cautions, please refer to the Owner’s
Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).

Axle Lock (Tru-Lok) — Rubicon Models

The AXLE LOCK switch is located on the instru­ment panel (to the right of the steering col­umn).

Axle Lock Switch Panel

This feature will only activate when the follow­ing conditions are met:

• Ignition in RUN position, vehicle in 4L (Low)
range.

• Vehicle speed should be 10 mph (16 km/h)
or less.

• Both right and left wheels on axle are at the
same speed.

To activate the system, push the AXLE LOCK
switch down to lock the rear axle only (the
“REAR ONLY” will illuminate), push the switch
up to lock the front axle and rear axle (the
“FRONT + REAR” will illuminate). When the
rear axle is locked, pushing the bottom of
switch again will lock or unlock the front axle.

NOTE:

The indicator lights will flash until the axles are
fully locked or unlocked.

To unlock the axles, push the AXLE LOCK OFF
button.

The axle lock disengages at speeds above
30 mph (48 km/h), and will automatically re­lock once vehicle speed is less than 10 mph
(16 km/h).

Engine STOP/START System
(ESS)

The STOP/START system was developed to re­duce emissions and will turn back ON every
time the ignition is turned OFF and then back
ON again. The system defaults back ON at
every ignition cycle.

STOP/START Off Switch

The system will stop the engine automatically
during a vehicle stop if the required conditions
are met.

Releasing the brake pedal or pressing the ac­celerator pedal will start the engine on a vehicle
equipped with an automatic transmission.
Pressing the clutch pedal will automatically
restart the engine on a vehicle equipped with an
manual tranmission.

How do I manually turn off/on the engine STOP/
START system?

• Press the STOP/START OFF switch (located
on the switch bank). The light on the switch
will illuminate when the system is off. The
light on the switch will turn off when system
is on.

What are possible reasons the engine does not
autostop?

• The hood is ajar.

• Driver’s door is open.

• Driver’s seat belt is unbuckled.

• The transmission is not in a forward gear.

PHONE PAIRING

• The vehicle is in 4LO transfer case mode (if
equipped).

• The vehicle has not reached a speed of
5 mph (8 km/h) after the previous autostop.

• Outside temperature is to cold or to hot for
system to operate.

• Engine has not reached normal operating
temperature.

• Cabin heating or cooling is in process and an
acceptable cabin temperature or setting has
not been achieved.

• Many of these reasons are displayed as a
STOP/START message in the instrument
cluster display within the STOP/START sec­tion. The system must be in the “STOP/
START READY” state to autostop. To access
the STOP/START section of the instrument
cluster display, use the display controls. Re­fer to the “Starting and Operating” section
of your Owner’s Manual for a complete list of
possible events in which the engine does not
autostop.

How do I know I am in an autostop?

• The engine will shut down, the tachometer
will move to the zero position and the STOP/
START telltale will illuminate in the instru­ment cluster.

How do I start the engine while in an autostop?

• While in a forward gear, the engine will start
when the brake pedal or clutch is pressed or
released or the throttle pedal is depressed.
The automatic transmission will re-engage
upon engine restart.

For further information, and applicable warn­ings and cautions, please refer to the Owner’s
Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).

Pairing Procedure

Make sure the ignition in the ACC or ON posi­tion.

1. Press either the “Phone” button or the “Set­tings” button in the Menu Bar on the touch­screen.

2. From the Settings list, select “Phone/
Bluetooth,” and then select “Paired Phones
and Audio Devices.”

NOTE:

A message will display asking, “No Phone Con­nected. Would you like to pair a phone?” Select
Yes. After pressing Yes, the radio prompts will
take you through the steps to connect your
phone via Bluetooth. Uconnect Phone will dis­play an “In progress” screen while the system is
connecting. Once the pairing has been success­ful, a message will display “Bluetooth pairing
successful: The device supports Phone and
Audio.” Click “OK.”

3. From the Phone button, the “Add Device”
option will be listed under the “Paired
Phones” section.

Uconnect 4C/4C NAV

For further information on Uconnect Phone,
refer to “Uconnect Phone” in the User’s Guide.

FRONT USB PORT/AUDIO JACK
(AUX) PORT

USB Port

Media Hub

1 — AUX Port
2 — Type C USB Port
3 — Type A USB Port

This feature allows an iPod or external USB
device to be plugged into the USB port. The
USB port supports certain iPod and iPhone
devices. The USB port also supports playing
music from external USB devices. Some iPod
software versions may not fully support the USB
port features. Please visit Apple’s website for

iPod software updates. Connect your iPod or
compatible device using a USB cable con­nected to the USB port. USB memory sticks
with audio files can also be used. Then, audio
from the device can be played on the vehicle’s
sound system while providing the artist, track
title, and album information on the radio dis­play (if available on device). When connected,
the iPod/USB device can be controlled using
the radio or steering wheel audio controls to
play, skip to the next or previous track, browse,
and list the contents.

USB Connection

NOTE:

• The Type C USB port is the primary media
port for the radio. Two devices can be
plugged in at the same time and both ports
provide charging capabilities, but only one
port can transfer data to the head unit at a
time.

• Both ports share a single data connection.
However, the user cannot switch between
Type A or Type C.

For example, if a device is plugged into the Type
A USB port and another device is plugged into
the Type C port, connection to the Type A port
will be lost. Alternatively, if a device is plugged
into the Type C port and another device is
plugged into the Type A port, the Type C device
maintains primary connection.

For additional information, refer to your Own­er’s Manual Supplement.

AUX/Audio Jack

The AUX/audio jack provides a means to con­nect a portable audio device, such as an
MP3 player, to the vehicle’s sound system. This
requires the use of a 3.5 mm stereo audio patch
cable. AUX mode is entered by pushing the
Media button. Once in Media mode, select the
AUX button when the audio jack is connected.
Volume on the connected device may need to
be adjusted to optimize audio quality.

SIRIUSXM GUARDIAN — IF
EQUIPPED

Activation

To use SiriusXM Guardian emergency, remote
and security services, you must activate your
SiriusXM Guardian account.

1. Press the Apps icon on the bottom of your
in-vehicle touchscreen.

2. Select the “Activate Services” icon from
your list of apps.

3. Select “Customer Care” to speak with a
SiriusXM Guardian Customer Care agent
who will activate services in your vehicle, or
select “Enter Email” to activate on the web.

Once you have activated your services, you’re
only a few steps away from using remote ser­vices.

Mobile App

To use SiriusXM Guardian remote services,
download the Uconnect Mobile app:

• Once downloaded, use your Owner Account
login and password to open the app.

• Include similar language: You will use your
SiriusXM Guardian PIN to execute these
remote services.

• Press the “Location” button on the bottom
menu bar of the app to bring up a map to
locate your vehicle or send a location to your
Uconnect Navigation, if equipped.

• Press the “Settings” side menu in the upper
left corner of the app to bring up app settings
and access the Assist Call Centers.

For further information:

• U.S. residents visit:
siriusxm.com/guardian

• Canadian residents visit:
siriusxm.ca/guardian/

Features

SiriusXM Guardian keeps you connected to your
vehicle. You have access to safety, remote and
security services.

In-Vehicle Features

SiriusXM Guardian enhances your ownership
and driving experience by connecting your ve­hicle to an operable network. When connected
to an operable network, you have access to:

• SOS Call: Connect to a live agent who con­tact emergency services and stays on the
line with you until help arrives.

• Customer Care Assistance: Speak with a live
agent when you press the ASSIST button on
your rearview mirror to get Roadside Assis­tance or support.

Remote Services

SiriusXM Guardian helps you activate features
from a distance. The remote services are:

• Vehicle Finder helps you find where you
parked your car.

• Send & Go allows you to send preset desti­nations to your navigation system for easy
access on the go.

• Remote Door Lock/Unlock lets you unlock or
lock your doors from any distance.

• Remote Horn & Lights allows you to sounds
your horn and flash your lights to easily find
your car.

• Receive monthly Vehicle Health Reports,
and Alerts whenever a problem is detected
under the hood.

Security Services

The Uconnect Mobile App helps you activate
features from a distance. The remote services
are:

• Receive text or email notifications if your
vehicle's security alarm goes off.

• Receive stolen vehicle assistance, using
GPS technology to help authorities locate
your vehicle if it is stolen.

SiriusXM Guardian remote services can be used
with the Uconnect app from virtually anywhere.

For further information on SiriusXM Guardian
or the Uconnect Mobile App, refer to your
Uconnect Owner’s Manual Supplement.

Vehicle Finder And Send & Go

Two of the most convenient remote features of
the Uconnect Mobile App are Vehicle Finder
and Send & Go.

Vehicle Finder

Vehicle Finder allows you to find the location of
your vehicle when you have lost it. You can also
sound the alarm and flash the lights to make
finding your vehicle even easier. To find your
vehicle:

1. Press the “Location” tab on the Uconnect
Mobile App bottom bar.

2. Select the “Vehicle” icon to determine the
location of your vehicle.

3. Select the “Find Route” button that ap­pears, once your vehicle is located.

4. Select your preferred Navigation App to
route a path to your vehicle.

Send & Go

Send & Go allows you to search for a destination
on your mobile device and then send the route
to your vehicle’s built-in navigation system. To
send a navigation route to your vehicle:

1. Press the “Location” tab on the Uconnect
Mobile App bottom bar.

2. Either type in the destination you would like
to navigate to, or search through one of the
categories provided.

3. Select the destination you want to route to
from the list that appears.

4. Press the “Send To Vehicle” button, and
then confirm the destination by pressing
“Yes,” to send the navigation route to the
Uconnect Navigation in your vehicle.

5. Finally, confirm the route inside your vehicle
by pressing the “Go Now” option on the
pop-up that appears on the touchscreen,
when the vehicle is started.

JEEP VEHICLE OWNER’S
MOBILE APP

NOTE:

The Owner’s Mobile App content is applicable
to vehicles sold in the U.S. market and are not
available from the Canadian App Store or
Google Play Store.

Key Features

• Owner Information For Your Vehicle

• Accident Assistant

• Online Service Scheduling

• Roadside Assistance

• Maintenance History

• And More

To get this FREE application, go directly to the
App Store or Google Play Store and enter the
search keyword “Jeep”.

The Jeep Vehicle Owner’s Information Applica­tion is the essential app for owners of Jeep
brand vehicles. The app puts driver and life­style information right in the palm of your hand,
anywhere you go. Whether it’s providing infor­mation about specific product features, taking
a tour through your vehicle’s equipment, stay-

ing up to date on your vehicle’s health, knowing
what steps to take following an accident, or
scheduling your next appointment, we know
you’ll find the app an important extension of
your Jeep vehicle. Simply download the FREE
app, select your make and model and enjoy the
ride.

Features/Benefits

• Available for free on iOS and Android smart­phones and tablets.

• Select Jeep brand vehicles from model year
2011 to current model year.

• You can also add other Chrysler, Dodge,
Ram, FIAT, or Alfa Romeo vehicles.*

• Easy access to vehicle information anywhere
you go using categories, bookmarks, search
and an A-Z index.

• Vehicle information such as operating in­structions, maintenance, service history, ve­hicle controls and emergency procedures.

• Find a dealer or an FCA-certified repair
facility.

• Easily document and email an accident
report.

• A parking reminder that allows you to drop a
pin on your location and navigate back to
your vehicle.

• Contact customer care with one click.

• Access to vehicle heritage, parts, accesso­ries, and social media networks.

• Schedule your next service appointment.

• Available in English and Spanish.

*App supports selected vehicles from model
year 2011 to present.

To get this FREE application, go directly to the
App Store or Google Play Store and enter the
search keyword “Jeep”.

AUTOMATIC CLIMATE
CONTROLS

Automatic Climate Controls
Overview

The Climate Control System allows you to regu­late the temperature, air flow, and direction of
air circulating throughout the vehicle. The con­trols are located on the instrument panel below
the radio.

Automatic Temperature Control — Automatic Op­eration

1. Push the AUTO button on the faceplate, or
the AUTO button on the touchscreen on the
Automatic Temperature Control (ATC)
Panel.

2. Next, adjust the temperature you would like
the system to maintain by adjusting the
driver and passenger temperature control
buttons. Once the desired temperature is
displayed, the system will achieve and au­tomatically maintain that comfort level.

3. When the system is set up for your comfort
level, it is not necessary to change the
settings. You will experience the greatest
efficiency by simply allowing the system to
function automatically.

Manual Operation Override:

This system offers a full complement of over­ride features. The AUTO symbol in the front
ATC display will be turned off when the system
is being used in the manual mode.

Whether it’s providing information about specifi c product features, taking a tour through your
vehicle’s heritage, knowing what steps to take following an accident, or scheduling your next
appointment, we know you’ll fi nd the app an important extension of your Jeep® brand vehicle.
Simply download the app, select your make and model and enjoy the ride.

To get this app, go directly to the App Store or Google Play and enter the search keyword “JEEP”
(U.S. residents only).

www.jeep.com⁄en ⁄owners (U.S.) provides special o ers tailored to your needs, customized vehicle galleries,
personalized service records and more. To get this information, just create an account and check back often.

Get warranty and other information online – you can review and print or download a copy of the Owner’s
Manual, Navigation ⁄ Uconnect manuals and the limited warranties provided by FCA US LLC for your vehicle
by visiting www.mopar.com (U.S.) or www.owners.mopar.ca (Canada). Click on the applicable link in the
“Popular Topics” area of the mopar.com (U.S.) or www.owners.mopar.ca (Canada) homepage and follow
the instructions to select the applicable year, make and model of your vehicle.

DOWNLOAD A FREE ELECTRONIC COPY of the most up-to-date Owner’s Manual,
media and warranty booklet by visiting:

www.mopar.com/en-us/care/owners-manual.html (U.S. residents);

www.owners.mopar.ca (Canadian residents).

Jeep.com (U.S.)

Jeep.ca (Canada)

WRANGLER

Third Edition

Quick Reference Guide

18JL-QRG-AA

©2018 FCA US LLC. All Rights Reserved.
Jeep is a registered trademark of FCA US LLC.