JCC JCEM001 User Manual

25mm

8mm

Earth (Green/Yellow)

Switched Live (Brown)

Neutral (Blue/grey)

Un/Switched Live (Black)

Wire preparation

1.0-1.5mm

company

JCC Emergency Remote Pack Self-Test

LV connection from Invertor to Luminaire

Mains supply from Invertor to LED Driver

LV connection from LED Driver to Invertor

OutIn

3A Fused Switched Live

Technical Support: [phone] Customer Services: [phone]

BS EN ISO9001 - 2015 - Registered Firm Certificate No. GB 1552

Important warranty information

This product is supported by a 2-year standard warranty which will extend to 3 years if registered within the first year of purc
(2 year on batteries). Please register at jcc.co.uk/warranty - Terms and conditions apply.

The installer will be asked to provide the following information, which is detailed on a label attached to the product’s chassi
Product Code/Date Code.

3 hour maintained LED emergency lighting pack

WARNINGS AND CAUTIONS

• To be installed in accordance with the local current wiring regulations and standards

• To avoid electric shock, serious injury or property damage, isolate power before installing, removing or servicing the product

• It is recommended that this product is installed by an electrician or a competent person with sufcient experience to install this product

• Any broken or damaged parts should be replaced as soon as possible. JCC will not accept responsibility for claims arising from sub-standard installations; which will void the warranty

• Emergency product routine inspection and tests must be undertaken at times of least risk and in accordance with EN 50172:2004. A copy of this report must accompany any tting returned to the JCC for any reason

INSTALLATION INSTRUCTIONS ENGLISH

• Read instructions and check that you have all of the tools and accessories required to complete the installation correctly. Isolate power supply before starting the installation.

a

1. Wire the emergency remote pack
to the mains supply as indicated

in gure 1. If a dimmable variant,

connect the dimming control wires
(DALI/1-10V/DSI) as shown in the
product instruction sheet

RoHS

Compliant

EL

IP20

2. Connect the two core cable from the

remote pack into the mains input terminals
of the driver (not supplied) as shown in

gure 2.

jcc.co.uk

3. Connect the driver low voltage

output from the driver to the

remote pack as shown in gure 3.

4

2

1

4. Connect the low voltage output

from the invertor to the luminaire

(not supplied) as shown in gure 4.

6. Ensure the green LED charge indicator is located alongside the luminaire and is

visible once the tting is installed and operational. Reconnect mains power

supply and test for operation. (Allow 24hrs for batteries to charge
before testing).

5. Connect batteries to the remote
pack prior to completing
the installation.

3

Electrical Input connection

5

100-240V~ 50/60Hz +1Hz
(6-60VDC 50W max output)
Class II with earth provision

NE

Usw/L Sw/L

NE

Usw/L Sw/L

Loop in/Loop out connections

4

JCC Lighting Products Ltd. Lux Park, Chichester Business Park, City Fields Way, Tangmere, Chichester, West Sussex, PO20 2FT

s:

hase.

3

2

Emergency range routine inspection and test

53

35

All tests must be undertaken at times of least risk and in accordance with EN 50172:2004 as
indicated below:

Prole & Dimensions

All dimensions in millimetres

258

.4

Daily: Indicators of the emergency remote pack should be visually inspected for correct operation.

Monthly: (in addition to the daily check) If automatic testing devices are used, the results of the

short duration tests shall be recorded. Test shall be carried out as follows:

Switch the luminaire over to emergency mode to operate from the batteries by simulating a

failure of supply to the normal lighting, for a period sufcient to ensure correct luminaire operation.

NOTE: The period of simulation failure should be sufcient for the purpose of this clause

whilst minimising damage to the system components e.g lamps. During this period,
all luminaires and signs shall be checked to ensure that they are present, clean and
functioning correctly. At the end of this test period, the supply to the normal lighting
should be restored and any indicator lamp or device should be checked to ensure that

is showing that the normal supply has been restored.

Annually: If automatic testing devices are used, the results of the short duration tests shall be

recorded. For all other systems the monthly inspection shall be carried out and the
following additional tests made:

a) Each luminaire and internally illuminated sign shall be tested monthly as above but for

its full duration in accordance with the manufacturer’s information.

b) The normal supply for the luminaire should be restored and any charge indicator lamp or

device should be checked to ensure that it shows the normal supply has been
restored. The charging arrangements should be checked for proper functioning.

c) The date of the test and its results shall be recorded in the system logbook.

A copy of this report must accompany any tting returned to the manufacturer for any reason.

General Information

Our products are designed to comply with the requirements of UK law and the relevant

industry national and international standards and should not be modied in any way. All

emergency lighting systems should comply with the recommendations of BS5266-1: Code of
Practice for the Emergency Lighting of Premises and be installed by competent engineers in
accordance with the relevant wiring regulations. Before installing any type of Emergency Lighting

always seek the advice and approval of the local Fire Prevention Ofcer (or equivalent authority).

Maintenance

Failed or faulty light sources connected to this equipment should be replaced immediately. These
units are designed especially for a long and trouble free life. Under normal conditions, will require
no routine maintenance or service beyond the inspection and test regime of BS5266-1.

Both mains supply and battery protection fusing is incorporated internally. Should access to these

or any other part of the circuitry be required this must be undertaken only by suitably qualied

person. Special care must be taken when removing the cover to circuitry and battery.
Only replacement components authorised by the company must be used. Disposal of replaced
components should be in accordance with the component manufacturers instructions.

Battery pack

Inverter

267

Operation/Testing LED Indicator Status

Normal operation Green solid Mains on/No fault

Normal operation Green solid Auto function test - 1 minute

Normal operation Green solid Auto 3 hour duration test

Fault indication

Fault indication

Fault indication Red ash Duration test fault

Red Flash/0.5s On 3.0s Off

Red Flash/2x 0.5s On 2.5s Off LED fault

Battery fault

Emergency test record sheet

Month Test Type First Year Second Year Third Year Fourth Year Fifth Year

Sign Date Sign Date Sign Date Sign Date Sign Date

January Functional

February Functional

March Functional

April Functional

May Functional

June Functional

July Functional

August Functional

September Functional

October Functional

November Functional

December 3 hour

V6_Jun_2022_RS