RadiaLED® Utility Range
To LED Tray
Fig. 1
220-240V~ 50/60Hz / Class I
Class I products must always be earthed
Luminaire
Mains Supply
(N)
(L)
Neutral: Blue
Live: Brown
Yellow/green
Unswitched Live: Black
Neutral: Blue
Black
Brown
Blue
s
Installation instructions for RadiaLED
WARNINGS AND CAUTIONS
• To avoid electric shock or serious injury or property damage, isolate power before installing,
removing or servicing the product
• It is recommended that this product is installed by an electrician or a competent person with
sufcient experience to install this product
• To be installed in accordance with the local current wiring regulations and standards
• Any broken or damaged parts should be replaced as soon as possible
Utility Bulkhead
®
a
company
• JCC will not accept responsibility for claims arising from sub-standard installations; which will void the warranty
• Ensure that you have the tools and accessories required to complete the installation correctly
• This luminaire is suitable for indoor use or exterior use, wall or ceiling mounting
• Do not install in areas that are near to continual running water
• Do not carry out insulation tests with this product connected to the circuit
• It may be necessary to uprate your MCBs to allow for increased inrush current
ENGLISHINSTALLATION INSTRUCTIONS
Mains supply Input : 220-240V~ 50/60Hz Class 1
Fig. 1
Standard versions
Live = Brown
Neutral = Blue
Emergency versions
Switched Live: Brown
Ceiling
applications
1A Fused Unswitched Live
Live = Brown
Yellow/green
Neutral = Blue
DALI
DA DA
To Driver
1-10V
+-
Wall
application
Wattage CCT CRI:Ra Lumens LpcW
12W 4000K 80 700*/1150** 58*/96**
21W 4000K 80 1350*/2000** 64*/95**
Diffuser: Opal (WOP)* or Prismatic (WPR)**
Installation
Ensure the xing surface is at and even. Use adequate xings with regard to type of surface.
1. Remove diffuser from luminaire by loosening the three securing screws.
2. All termination points are under the LED tray and this can be removed by loosening the locating
screws and rotating the tray until keyhole slots allow removal.
3. Ensure incoming cables are weather protected.
4. Pass intended supply wires through grommet or CTS gland.
5. Fix base in desired location, taking care to avoid pipes and cables that may be hidden.
6. Make connections and connect dimming controls as required for DALI/1-10V versions (Fig.1).
7. Re-attach LED tray to mounts and tighten screws.
8. Replace diffuser and tighten screws evenly.
9. Switch on mains.
IP65
jcc.co.uk
V3_Jun_2022_RS
Sensor data can be set using DIP switches on the sensor. The settings are as follows:
Microwave On/Off operation and settings
Detection Area
I: Up to 8m
II: Up to 6m
III: Up to 4m
VI: Up to 3m
V: Up to 2m
II
III
IV
1 2
OnI
-
On
-
-
On
On
On
V
Note that reducing detection area
will also reduce sensitivity.
3
100%
On
75%
On
50%
On
-
25%
On
-
10%
-
-
On
Refers to the time period the lamp
remains at 100% illumination after
no motion detected.
Microwave Step Dim operation and settings - 12W version only
Detection Area Hold Time Standby Period Standby Dimming Level Daylight Sensor
On
On
-
-
-
3
On
On
On
On
100%
75%
50%
25%
10%
-
II
III
IV
1 2
OnI
-
On
-
-
On
V
I: Up to 8m
II: Up to 6m
III: Up to 4m
VI: Up to 3m
V: Up to 2m
Note that reducing detection area
will also reduce sensitivity.
On
Refers to the time period the lamp
remains at 100% illumination after
no motion detected.
II
III
IV
V
VI
1 2 3
OnI
OnOnOn
-
On
On
-
-
-
On
-
-
On
On
On
-
-
5s
30s
90s
3min
20min
30min
On
Refers to the time period the lamp
remains at a low light level before it
completely switches off in the long
absense of people.
Hold Time
1 2 3
OnI
II
III
IV
V
VI
-
On
-
On
-
II
III
IV
V
VI
OnOnOn
On
On
-
On
-
On
-
-
-
1 2 3
OnI
OnOnOn
-
On
On
-
-
-
On
-
-
5s
30s
90s
3min
20min
30min
On
On
On
-
-
I: Disable*
II: 50lux
(twilight operation only)
Ill: 30lux
(twilight operation only)
IV: 10lux
(darkness operation only)
V: 5lux
(darkness operation only)
The sensor can be set to only allow the lamp to illuminate below a
dened ambient brightness threshold.
*When set to Disable mode, the daylight sensor will switch on the
lamp when motion is detected regardless of ambient light level.
II
III
IV
1 2
OnI
-
On
On On
Disable*
1hr
30min
10min
5min
5sec
On
V
Refers to the low light level you
would like to have after the hold
time in the long absense of people.
On
On
-
--
3
On
On
On
Daylight Sensor
II
III
IV
V
II
III
IV
V
1 2 3
OnI
OnOnOn
On
On
-
On
1 2 3
OnI
OnOnOn
On
On
-
On
Disable
50lux
-
30lux
-
10lux
--
5lux
---
Disable
50lux
-
30lux
-
10lux
--
5lux
---
On
50%
40%
30%
20%
-
10%
-
On
The sensor can be set to only
allow the lamp to illuminate below
a dened ambient brightness
threshold.
*When set to Disable mode, the
daylight sensor will switch on the
lamp when motion is detected
regardless of ambient light level.
Loading...