JBL Partybox 300 User Manual

PARTYBOX 200
PARTYBOX 300

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

For all products:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not block any ventilation openings. Install this apparatus
in accordance with the manufacturer’s instructions.

6. Do not install this apparatus near any heat sources such as
radiators, heat registers, stoves or other apparatus (including

ampliers) that produce heat.

7. Do not defeat the safety purpose of the polarized or grounding­type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong

is provided for your safety. If the provided plug does not t

into your outlet, consult an electrician for replacement of the
obsolete outlet.

8. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles and the point
where they exit from the apparatus.

9. Use only attachments/accessories specied by the

manufacturer.

10. Use only with the cart, stand, tripod, bracket or

table specied by the manufacturer or sold with

the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination
to avoid injury from tip-over.

11. Unplug this apparatus during lightning storms or when
unused for long periods of time.

12. To disconnect this apparatus from the AC mains completely,
disconnect the power-supply cord plug from the AC
receptacle.

13. The mains plug of the power-supply cord shall remain readily
operable.

14. Do not expose batteries to excessive heat such as sunshine,

re or the like.

15. This apparatus is intended to be used only with the power
supply and/or charging cable provided by the manufacturer.

Caution FCC and IC statement for users (USA and Canada
only)

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause
undesired operation.

CAN ICES-3(B)/NMB-3(B)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for
help.

Caution: Changes or modications not expressly approved

by HARMAN could void the user’s authority to operate the
equipment.

For Products That Transmit RF Energy

FCC AND IC INFORMATION FOR USERS

This device complies with Part 15 of the FCC rules and Industry

Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) This device may not cause
harmful interference; and (2) this device must accept any

interference received, including interference that may cause
undesired operation.

FCC/IC Radiation Exposure Statement

This equipment complies with FCC/IC RSS-102 radiation
exposure limits set forth for an uncontrolled environment.

FCC Caution:

High power radars are allocated as primary users of the 5.25 to

5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations

can cause interference with and/or damage this device. No

conguration controls are provided for this wireless equipment

allowing any change in the frequency of operations outside the
FCC grant of authorization for US operation according to Part

15.407 of the FCC rules.

IC Caution:

User should also be advised that:

(i) The device for operation in the band 5150-5250 MHz is only

for indoor use to reduce the potential for harmful interference to

2

English

co-channel mobile satellite systems; (ii) the maximum antenna

gain permitted for devices in the bands 5250-5350 MHz and

5470-5725 MHz shall comply with the e.i.r.p. Limit: and (iii)

The maximum antenna gain permitted for devices in the band

5725-5825 MHz shall comply with the e.i.r.p. Limits specied for

point-to-point and non-point-to-point operation as appropriate.

(iv) Users should also be advised that high-power radars are
allocated as primary users (i.e. priority users) of the bands 5250-

5350 MHz and 5650-5850 MHz and that these radars could
cause interference and/or damage to LE-LAN devices.

Exposure of humans to RF fields (RSS-102)

The computers employ low gain integral antennas that do not

emit RF eld in excess of Health Canada limits for the general

population; consult Safety Code 6, obtainable from Health
Canada’s Website at http://www.hc-sc.gc.ca/

The radiated energy from the antennas connected to the wireless
adapters conforms to the IC limit of the RF exposure requirement
regarding IC RSS-102, Issue 5 clause 4. SAR tests are conducted
using recommended operating positions accepted by the FCC/
RSS with the device transmitting at its highest away from the
body. Non-compliance with the above restrictions may result in
a violation of FCC RF exposure guidelines.

Use Restriction: Attention in France, the operation is limited to
indoor use within the band 5150-5350 Mhz.

FOR ALL EU COUNTRIES

For products that include audio out
Prevention of hearing loss

Caution: Permanent hearing loss may occur

if earphones or headphones are used at high
volume for prolonged periods of time.

For France, the products have been tested to
comply with Sound Pressure Level requirement
laid down in the applicable NF EN 50332 L.5232-1.

Note:

– To prevent possible hearing damage, do not listen to high volume

levels for long periods.

WEEE Notice

The Directive on Waste Electrical Equipment (WEEE), which

entered into force as European law on 14/02/2014, resulted in
a major change in the treatment of electrical equipment at end­of-life.

The purpose of this Directive is, a rst priority, the prevention of

WEEE, and in addition, to promote the reuse, recycling and other
forms of recovery of such wastes as so as to reduce disposal.

The WEEE logo on the product or on its box indicating collection
for electrical and electronic equipment consists of the crossed­out wheeled bin, as shown below.

For Products with Radio Receivers That Can Use an External Antenna (USA ONLY)

CATV (Cable TV) or Antenna Grounding

If an outside antenna or cable system is connected to this
product, be certain that it is grounded so as to provide some
protection against voltage surges and static charges. Section

810 of the National Electrical Code (NEC), ANSI/NFPA No. 700-

1984, provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes
and requirements of the electrode.

Note to CATV System Installer

This reminder is provided to call the CATV(cable TV) system

installer’s attention to article 820-40 of the NEC, which provides
guidelines for proper grounding and, in particular, as close to the
point of cable entry as possible.

Caution: This product uses a laser system. To prevent direct
exposure to the laser, do not open the cabinet enclosure or defeat
any of the safety mechanisms provided for your protection. Do
NOT START INTO THE LASER BEAM. To ensure proper use of
this product, please read the owner’s manual carefully and retain
it for future use. Should the unit require maintenance or repair,

please contact your local JBL service. Refer servicing to qualied

personnel only.

This product must not be disposed of or dumped with
your other household waste. You are liable to dispose
of all your electronic or electrical waste equipment by

relocating over to the specied collection point for

recycling of such hazardous waste. Isolated collection
and proper recovery of your electronic and electrical waste
equipment at the time of disposal will allow us to help conserving
natural resources. Moreover, proper recycling, and collection
points, please contact your local city center, household waste
disposal service, shop from where you purchased the equipment,
or manufacturer of the equipment.

RoHS Compliance

This product is in compliance with Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011 on the
restriction of the use of certain hazardous substances in electrical
and electronic equipment.

For Products that includes Batteries

EU Batteries Directive 2013/56/EU

A new battery directive 2013/56/eu on Battery and Accumulator
replacing directive entered into force on the 01/07/2015. The
directive applies to all types of batteries and accumulator

(AA, AAA, button cells, rechargeable packs) including those

incorporated into appliances except for military, medical
and power tool applications. The directive sets out rules for
collection, treatment, recycling and disposal of batteries, and
aims to prohibit certain hazardous substances and to improve
environmental performance of batteries and all operators in the
supply chain.

www.jbl.com

3

Instructions for Users on Removal, Recycling and Disposal
of Batteries

The remove the batteries from your equipment or remote control,
reverse the procedure described in the owner’s manual for
inserting batteries. For products with a built-in battery that lasts
for the lifetime of the product, removal may not be possible for
the user. In this case, recycling or recovery, it becomes necessary
to replace such a battery, this procedure must be performed by
authorized services centers. In the European Union and other
locations, it is illegal to dispose of any battery with household
trash. All batteries must be disposed of in an environmentally

sound manner. Contact your local waste-management ofcials

for information regarding the environmentally sound collection,
recycling and disposal of used batteries.

WARNING: Danger of explosion if battery is incorrectly replaced.

To reduce risk of re or burns, don’t disassemble, crush,

puncture, short external contact, expose to temperature above

60°C (140°F), or dispose of in re or water. Replace only with
specied batteries. The symbol indicating ‘separate collection’

for all batteries and accumulators shall be crossed-out wheeled
bin shown below:

In case of batteries, accumulators and button cells containing
more than 0.0005 mercury, more than 0.002% cadmium or more
than 0.004% lead, shall be marked with the chemical symbol for
the metal concerned: Hg,Cd or Pb respectively. Please Refer to
the below symbol:

EPILEPSY
WARNING

A few people may experience epileptic

seizures when viewing ashing lights.

WARNING: DO NOT INGEST BATTERIES, CHEMICAL BURN
HAZARD [the remote supplied with] This product contains a coin/
button cell battery. If the coin/button cell battery is swallowed, it
can cause severe international burns in just 2 hours and can lead
to death. Keep new and used batteries away from children. If you
think batteries might have been swallowed or placed inside any
part of body, seek immediate medical attention.

For All Products Except Those with Wireless Operation

HARMAN International hereby declares that this equipment is in
compliance with EMC 2014/30/EU Directive, LVD 2014/35/EU
Directive. The declaration of conformity may be consulted in the
support section of our Web Site, accessible from www.jbl.com.

For All Products with Wireless Operation

HARMAN International hereby declares that this equipment
is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU. The declaration of
conformity may be consulted in the support section of our Web
Site, accessible from www.jbl.com.

4

TABLE OF CONTENTS

English

IMPORTANT SAFETY INSTRUCTIONS 2

FEDERAL COMMUNICATION COMMISSION
INTERFERENCE STATEMENT 2

FOR PRODUCTS THAT TRANSMIT RF ENERGY 2

EXPOSURE OF HUMANS TO RF FIELDS (RSS-102) 3

FOR PRODUCTS WITH RADIO RECEIVERS THAT CAN

USE AN EXTERNAL ANTENNA (USA ONLY) 3

FOR ALL EU COUNTRIES 3

FOR PRODUCTS THAT INCLUDES BATTERIES 3

FOR ALL PRODUCTS EXCEPT THOSE WITH WIRELESS
OPERATION 4

FOR ALL PRODUCTS WITH WIRELESS OPERATION 4

1. INTRODUCTION 6

2. WHAT’S IN THE BOX 6

3. PRODUCT OVERVIEW 7

3.1 TOP PANEL 7

3.2 BACK PANEL 7

7. USING YOUR PARTYBOX 9

7.1 BLUETOOTH CONNECTION 9

7.2 USB CONNECTION 9

7.3 AUX CONNECTION 10

7.4 INPUT CONNECTION 10

7.5 MIX SOUND WITH A MICROPHONE OR GUITAR 11

7.6 CHARGING EXTERNAL USB DEVICES 11

8. CARRYING YOUR PARTYBOX 12

9. SETTINGS 12

9.1 TWS MODE 12

9.2 DEMO MODE 12

9.3 STANDBY MODE 12

10. SPECIFICATIONS 13

11. TROUBLESHOOTINGS 13

4. PLACEMENT 8

5. POWER ON 8

6. CHARGING (PARTYBOX 300 ONLY) 9

6.1 CHARGE YOUR SPEAKER 9

6.2 CHECK THE BATTERY LEVEL 9

12. COMPLIANCE 14

13. TRADEMARK 14

www.jbl.com

5

1. INTRODUCTION

2. WHAT’S IN THE BOX

Congratulations on your purchase! This manual includes
information about “PARTYBOX 200” and “PARTYBOX 300”
speakers. We encourage you to take a few minutes to read this
manual, which describes the product and includes step-by-step
instructions to help you to set up and get started. Read and
understand all the safety instructions before using your product.

If you have any questions about these products, their installation
or their operation, please contact your retailer or customer
service, or visit us at www.jbl.com.

1

1) Main unit

2) Power cord*

3) DC cable
*Power cord quantity and plug type vary by regions.

2

3

6

3. PRODUCT OVERVIEW

3.1 Top Panel

PartyBox 300

1

2

3

PartyBox 200

English

6)

• Turn the power on or off.

7)

LED behavior

7

6

5

4

(for PartyBox

300 only)

(PartyBox 300 only)

• Battery level indicator.

Caution:

– Do not look directly at the light-emitting parts when the speaker

lights are turned on.

White (Constant) Power on

Amber (Constant) Standby

Off Power off

White (Fast ash) Pairing

White (Constant) Connected

Off Not connected

White (Constant) On

Off Off

Red (Fast ash) Low battery

White (Slow ash) Charging

White (Constant) Charged

1

2

3

1) /

• Increase or decrease the volume level.

2)

• Play, pause or resume.

3)

• Press to enhance bass or restore.

4)

• Press to toggle between different light patterns.

• Press to turn Off / On, all the lights.

• Press and hold for 2 seconds to turn the strobe light on
or off.

5)

• Press to enter Bluetooth pairing mode.

• Press and hold for 2 seconds to enter True Wireless

Stereo (TWS).

• Press and hold for 10 seconds to forget all paired devices.

3.2 Back Panel

1

6

5

4

2

3

4

5

6

1) AUX

• Connect to an external audio device through a 3.5mm

audio cable (not supplied).

2) USB

• Connect to a USB storage device.

• Charge an external USB device.

3) DC

• Connect to a car charger.

4) AC

• Connect to AC power supply.

5) INPUT

• Connect to the analog audio output jacks of an analog

device through RCA (red/white) audio cable (not supplied).

6) OUTPUT

• Connect to the analog audio input jacks of an analog

device through RCA (red/white) audio cable (not supplied).

7) MIC

• Connect to a microphone.

8) GUITAR

• Connect to the guitar.

10

9

8

7

www.jbl.com

7

4. PLACEMENT

5. POWER ON

Notes:

– For best quality sound, ensure the two tweeters are placed on the

upper side of the speaker box.

– Do not sit on the speaker or push it. Otherwise, it may result in

malfunction and causing personal injury and /or property damage.

Place the speaker on a at, stable surface and make sure that the

rubber feet side is down. You can place the speaker vertically or
horizontally. It automatically optimizes sound to adapt to placing
orientation.

a

b

Vertical Horizontal

Cautions:

– Use only provided power cord.
– For PartyBox 300, either AC/DC power or built-in battery can be

used as a power supply.

1. Plug one end of the AC power cord into the power connector
on the back of the speaker, then plug the other end to a wall
outlet.

2. Connect the car charger to the DC power jack of the speaker,
and then to your vehicle’s car charger outlet.

8

English

6. CHARGING (PartyBox 300 only)

PartyBox 300 is powered by a built-in rechargeable battery.

Notes:

– Fully charge the built-in battery before using for the rst time, which

will prolong the battery lifespan.

– Built-in battery charging works on AC power only.

6.1 Charge your Speaker

Use the AC power to charge your PartyBox 300.

6.2 Check the Battery Level

The speaker is powered by the built-in rechargeable battery.
After power-on, the speaker shows the battery level immediately,
you can check the status of the PartyBox battery by pressing
on any button.

7. USING YOUR PARTYBOX

7.1 Bluetooth Connection

You can use your PartyBox as an external speaker for your
Bluetooth enabled smartphone or tablet.

1. Press

2. Choose “PartyBox 200” or “PartyBox 300” to connect.

3. Once successfully connected, audio will stream from your

Notes:

– This speaker can memorize a maximum of 8 paired devices. The

– The operational range between this speaker and a Bluetooth device

– If a PIN code is requested while connecting a Bluetooth device,

– Bluetooth performance can be affected by the distance between

to enter Bluetooth pairing mode.

1

2

10m (30”)

Bluetooth device to this speaker.

ninth paired device will replace the rst one.

is approximately 10 meters (30 feet).

enter “0000”.

this product and your Bluetooth device and the environment of
operation.

Bluetooth

Bluetooth

DEVICES

JBL PartyBox 300

JBL PartyBox 200

To terminate the Bluetooth-enabled device:

• Turn off this speaker;

• Disable Bluetooth on your device; or

• Move this speaker beyond the Bluetooth operational range.

To reconnect the Bluetooth-enabled device:

• When you turn on this speaker next time, it tries to reconnect
the last connected device automatically;

• If not, manually select “JBL PartyBox 300” or “JBL PartyBox

200” on your Bluetooth device to start a connection.

Note:

– To exit Bluetooth mode, insert a USB storage device.

www.jbl.com

9

7.2 USB Connection

With your PartyBox, you can enjoy music that is stored on a
USB storage device such as an MP3 player.

Plug your USB storage device into the USB port of your PartyBox.
The music will play automatically. If not, please check if the USB

device contains playable audio contents.

2. Turn on your portable audio device and it starts playing.

2

1

Note:

– To exit AUX mod, choose Bluetooth or USB as a source rst.

7.4 INPUT Connection

Audio formats

Extension Codec Sample rate Bitrate

WAVE PCM 44.1KHz ~192KHz < 5Mbps

LPCM

IMA_
ADPCM

MPEG

MULAW

MP3 MPEG1

layer1/2/3

MPEG2
layer1/2/3

MPEG2.5
layer3

WMA ≤ 320Kbps 8Kbps ~

44.1KHz ~192KHz

44.1KHz ~192KHz

44.1KHz ~192KHz

44.1KHz ~192KHz

32KHz ~48KHz 32Kbps ~

16KHz ~24KHz 8Kbps ~

8KHz ~12KHz 8Kbps ~

< 5Mbps

< 5Mbps

< 5Mbps

< 5Mbps

320Kbps

160Kbps

160Kbps

48Kbps

7.3 AUX Connection

Notes:

– When the USB source is not playing, Bluetooth can break in and

play music from the phone.
– When USB is playing, Bluetooth cannot break in USB.
– Priority goes to USB, Bluetooth and then Aux.

Note:

– To play music on your analog device through this speaker, make

sure that no Bluetooth connection, USB device, or AUX connection
is available.

Connect a pair of RCA audio cables (red/white, not supplied) to:

• the RCA audio output sockets (red/white) on the analog
device (TV, DVD player, etc);

• the INPUT (L/R) connectors on the rear of this speaker.

AUDIO OUT

L

R

.
.
.

To play music on your portable audio device through this
speaker, make sure that no Bluetooth connection or USB device
is available.

1. Connect a 3.5mm audio cable (not supplied) to:

• the headphone socket of your portable audio device;

• the AUX connector of this speaker.

10

English

7.5 Mix Sound with a Microphone or Guitar

By using a microphone (not supplied) or an electric guitar (not
supplied), you can mix its sound with an audio source.

1. Rotate counterclockwise the MIC/GUITAR volume knob to
turn down the volume.

2. Connect your microphone or guitar to the MIC/GUITAR jack
of this speaker.

3. Sing through the microphone or play guitar.

• To adjust the volume of the audio source, press

• To adjust the volume of the microphone or guitar, rotate

the MIC/GUITAR volume knob.

/ ;

7.6 Charging External USB Devices

You can use this speaker as a battery charger for your
rechargeable USB devices.

Connect your USB device to the USB port on the rear of this
speaker.

PartyBox 300

PartyBox 200

Caution:

– When not using the microphone or guitar, decrease the MIC/

GUITAR volume to minimum and remove them from the jack.

www.jbl.com

11

8. CARRYING YOUR PARTYBOX

9. SETTINGS

Cautions:

– Before carrying the speaker, make sure that all the cords are

disconnected.

– To avoid personal injury and/or property damage, hold the product

rmly while carrying.

9.1 TWS Mode

The two PartyBox speakers can connect to each other in TWS
mode.

1. Press and hold
seconds, TWS connection will be built up. By default, the
speaker which connected to your smartphone is the master

speaker (L channel), the other one is the slave speaker (R
channel).

2. Press L/R button on one speaker to toggle between L
channel / R channel / Stereo, another speaker will change
the setting automatically.

3. In TWS mode, press and hold
speaker or power off the speaker to exit the TWS mode.

on both speakers simultaneously for 5

for 5 seconds on either

10m (30”)

9.2 Demo Mode

Cautions:

– If you plugged out the AC power (PartyBox 300 only), then you

plugged it in, the Demo Mode will be resumed automatically.

– Ensure PartyBox is powered by AC to go into Demo Mode.

To enter or to exit demo mode, press and hold and
simultaneously for 5 seconds.

In demo mode, all the input sources are disabled, all buttons but

/

/

Note:

– The PartyBox built-in with 3 x 30 seconds music tracks.

Playback

• Press once

• Press once

/ are disabled.

to start, pause or resume play.
after the pause, to play the next track.

9.3 Standby Mode

The product will enter into sleep mode after 20 minutes without
operation.

• If the“PartyBox” powered by the battery, it will auto power off
if no action for 20 minutes.

• If the “PartyBox” powered by AC or DC power source, the
product will enter standby mode if no action for 20 minutes.

Press
the speaker will enter normal mode.

(power) or Bluetooth stream break-in in standby mode,

12

English

10. SPECIFICATIONS

Product name PartyBox 300 PartyBox 200

AC power input 100-240V ~ 50/60Hz

DC power input 12V

Built-in battery Li-ion 10.4Ah, 7.2V N/A

Power consumption 60W

Standby power
consumption

USB output 5V

Speaker drivers 2 woofer + 3 tweeter

Speaker impedance 4 ohm

Total output power 120 W RMS

Signal-to-noise (S/N)
ratio 65 dBA

Frequency response 45 Hz - 18 KHz (-6dB)

Bluetooth version 4.2

Bluetooth prole A2DP, AVRCP

Bluetooth transmitter
frequency range 2402 - 2480 MHz

Bluetooth maximum
transmitter power 8dBm (EIRP)

Bluetooth transmitter
modulation GFSK, π/4 DQPSK, 8DPSK

Bluetooth range Approx. 10 m (33 feet)

USB format FAT16, FAT32

USB le format .mp3, .wma, .wav

Input sensitivity • AUX in: 500mV rms (RCA

Dimension (W x H x D) 330 x 688 x 323 mm /

Net weight 15.84 kg 15.32 kg

8A

<2W with BT connecting; <0.5W
without BT connecting

2.1A

connector); 250 mV rms
(3.5mm connector).

• Digital input:
Bluetooth/USB -12dBFS

13 x 27 x 12.7 in

11. TROUBLESHOOTINGS

Caution:

– Never try to repair the product by yourself. If you have any

problems while using this product, check the following points
before you request service.

System

The unit will not turn on.

• Check if the power cord is plugged into the outlet and to the
PartyBox.

• For “PartyBox 300” make sure the speaker is fully charged,
if not use the power cord to turn on your speaker.

Sound

No sound from the PartyBox.

• Make sure that the PartyBox is powered on.

• Make sure that volume level is turned to an audible level.

• Make sure that it is connected to a music source.

Bluetooth

A device cannot connect with the PartyBox.

• Check if you enable the Bluetooth function of the device.

• The PartyBox is already connected to another Bluetooth
device. Press and hold on Bluetooth to disconnect and pair
with a new device.

Poor audio quality from a connected Bluetooth device.

• The Bluetooth reception is poor. Move the device closer to
the PartyBox, or remove any obstacle between the device
and the PartyBox.

www.jbl.com

13

12. COMPLIANCE

The product is in compliance with the European Union energy
legislation.

Bluetooth connection mode

The product is intended to be used for streaming music via
Bluetooth connection. A consumer can stream Bluetooth
audio to the speaker. When the product is connected through
Bluetooth, the Bluetooth connection must remain active at all
times to ensure proper operation.

The product will enter into sleep mode (networked standby),

after 20 minutes without operation, the power consumption @
sleep is less than 2.0 Watts, after which it can be re-activated
via Bluetooth connection.

Bluetooth disconnection mode

The product will enter into standby mode, after 20 minutes
without operation, the power consumption @ standby is less
than 0.5 Watts.

13. TRADEMARK

Este equipamento não tem direito à proteção contra interferência
prejudicial e não pode causar interferência em sistemas
devidamente autorizados.

Este produto está homologado pela ANATEL, de acordo com
os procedimentos regulamentados pela Resolução 242/2000, e
atende aos requisitos técnicos aplicados.

Para maiores informações, consulte o site da ANATEL – www.
anatel.gov.br

The Bluetooth® word mark and logos are registered trademarks
owned by the Bluetooth SIG, Inc. and any use of such marks by
HARMAN International Industries, Incorporated is under license.
Other trademarks and trade names are those of their respective
owners.

14

Торговая марка : JBL

Назначение товара : Активная акустическая система

Изготовитель : Харман Интернешнл Индастриз Инкорпорейтед, США, 06901 Коннектикут, г.Стэмфорд, Атлантик

Стрит 400, офис 1500

Страна происхождения : Китай

Импортер в Россию : OOO “ХАРМАН РУС СиАйЭс“, Россия, 127018, г.Москва, ул. Двинцев, д.12, к 1

Гарантийный период : 1 год

Информация о сервисных центрах : www.harman.com/ru тел. [phone]

Срок службы : 5 лет

Товар сертифицирован

Дата производства : Дата изготовления устройства определяется по двум буквенным обозначениям из второй группы

символов серийного номера изделия, следующих после разделительного знака «-». Кодировка
соответствует порядку букв латинского алфавита, начиная с января 2010 года: 000000-MY0000000,
где «M» - месяц производства (А - январь, B - февраль, C - март и т.д.) и «Y» - год производства (A ­2010, B - 2011, C - 2012 и т.д.).

HARMAN International Industries,
Incorporated 8500 Balboa
Boulevard, Northridge, CA 91329
USA

www.jbl.com

© 2018 HARMAN International Industries, Incorporated. All rights reserved. JBL is a trademark
of HARMAN International Industries, Incorporated, registered in the United States and/or other

countries. Features, specications and appearance are subject to change without notice. The

Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by HARMAN International Industries, Incorporated is under license.
Other trademarks and trade names are those of their respective owners. The terms HDMI, the

HDMI logo, and High-Denition Multimedia Interface are trademarks or registered trademarks

of HDMI Licensing LLC in the United States and other countries. Manufactured under
license from Dolby Laboratories. Dolby, Dolby Audio, Pro Logic and the double-D symbol are
trademarks of Dolby Laboratories.