JBL BP600.1, P80.2, P180.2, BP300.1, P80.4 User Manual
...
Power Series Amplifiers
P80.2, P180.2, P80.4, BP150.1, BP300.1, BP600.1, BP1200.1 Owner’s Manual
GENUINE JBL
2
Thank you for purchasing a JBL Power
Series™ amplifier. In order that we may
better serve you should you require
warranty service for your new amplifier,
please retain your original purchase
receipt and return the enclosed warranty
registration card.
Warning: Playing loud music in an automobile can permanently damage your
hearing as well as hinder your ability to
hear traffic. We recommend listening at
low levels while driving your car. JBL
accepts no liability for hearing loss, bodily
injury or property damage resulting from
use or misuse of this product.
Important: Installation of automotive
stereo components can require extensive
experience in performing a variety of
mechanical and electrical procedures.
Although these instructions explain, in a
general sense, how to install Power
Series amplifiers, they may not show
the exact installation methods for your
particular vehicle. If you feel you lack the
necessary tools or experience, ask your
authorized JBL car-audio dealer about
professional installation options.
Installation Warnings and Tips
• Always wear protective eyewear when
using tools.
• Turn off all audio systems and other
electrical devices before you start.
Disconnect the (–) negative lead from
your vehicle’s battery.
• Check clearances on both sides of a
planned mounting surface before
drilling any holes or installing any
screws. Remember that the screws can
extend behind the surface.
• At the installation sites, locate and
make a note of all fuel lines, hydraulic
brake lines, vacuum lines and electrical
wiring. Use extreme caution when
cutting or drilling in and around these
areas.
• Before drilling or cutting holes, use a
utility knife to remove unwanted fabric
or vinyl to keep material from snagging
in a drill bit.
• When routing cables, keep input-signal
cables away from power cables and
speaker wires.
• When making connections, make
certain they are secure and properly
insulated.
• If the amplifier’s fuse must be replaced,
use only the same type and rating as
that of the original. Do not substitute
another kind.
Choosing a Location and
Mounting the Amplifier
Amplifiers need air to stay cool. Suitable
locations are under a seat (provided the
amplifier doesn’t interfere with the seat
adjustment mechanism), in the trunk or
in any other location which provides
enough air for the amp to cool itself. Do
not mount the amplifier with the heat
sink facing downward, as this makes
convection cooling of the amplifier
impossible.
Mount the amplifier so that it is not
damaged by the feet of back-seat passengers or shifting cargo in the trunk.
Mount the amplifier so that it remains
dry – never mount an amplifier outside
the car or in the engine compartment.
Using the amplifier as a template, mark
the location of the mounting holes on
the mounting surface, drill pilot holes,
and attach the amplifier to the mounting
surface with screws. Make sure the
amplifier is mounted securely.
BP150.1, BP300.1, BP600.1, BP1200.1
FUSES 40A x 3
+ — — +
SPEAKER OUTPUTS
RR
+ — — + — ++ —
R L R L
HIGH LEVEL
LL
FRONT INPUTS
REAR INPUTS
HIGH LEVEL
+ BATT REM GND
POWER
INPUT
LPF
LEVEL
4V 250mV 32Hz 320Hz 0dB +6dB
BASS
FREQ
BOOST
P80.2, P180.2
— +
— +
+ R – – L +
HIGH LEVEL
L + — R
BRIDGED
SPEAKER OUTPUTS
R
L
INPUTS
FUSES 20A x 2
INPUT
LEVEL
4V 250mV
INPUT MODE
ST MD
+BATT REM GND
X-OVER
FLAT HP LP
32Hz320Hz
FREQ
POWER
Note: Drawing is provided only for connector, control and fuse location.
Please see “Specifications” for fuse requirements.
Figure 1
P80.4
X-OVER INPUT MODE X-OVER
R
FLAT HP LP ST MD ST MD FLAT HP LP
+ R – – L ++ R – – L +
HIGH LEVEL HIGH LEVEL
SPEAKER OUTPUTS
FRONT
REAR
– L + – R +
– +
4V 250mV 32Hz 320Hz 32Hz 320Hz 4V 250mV
L
LEVEL FREQ FREQ LEVEL
FRONT REAR
FUSES 20A x 2
R
L
+BATT REM GND
POWERBRIDGED
Figure 3
Note: Drawing is provided only for connector, control and fuse location.
Please see “Specifications” for fuse requirements.
Figure 2
3
Loading...