Jaypro Sports BBC-SPDKT User Manual
TYP SUSPENDED
TYP SUSPENDED
LOWER NET ATTACHMENT
OPTIONAL SPREADER KIT
MODEL #: BBC-SCKT
TURNBUCKLE
OPTIONAL WALL MOUNTING KIT
MODEL #: BBC-WLKT
--- BBC-SPDKT--
(Cable Suspended Tunnel kit)
Installation Instructions
UPPER NET ATTACHMENT
Call Jaypro Sports Equipment at 1-800-243-0533 during
Rev - B Page 1 of 13
regular business hours for technical support.
www.jaypro.com
JAYPRO SPORTS
BBC-SPDKT, INDOOR CABLE SUSPENDED BATTING TUNNEL KIT
IMPORTANT NOTICE:
1) DO NOT SET CAGE OR NET TOO CLOSE TO WALLS, COLUMNS, CEILINGS OR
ANY SOLID OBJECT WHERE BALLS CAN STRIKE AND BOUND BACK. CAGE OR
NET SHOULD BE AT LEAST 4 FEET FROM ALL BYSTANDERS, CEILINGS, WALLS
OR SOLID OBJECTS.
2) SPECTATORS MUST NOT STAND IN BACK OR NEAR SIDES OF CAGE OR NET
WHILE BEING USED FOR BATTING PRACTICE.
3) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE HAZARDOUS
AND RESULT IN INJURY. FOR REPAIR OR REPLACEMENT, CONTACT YOUR
DEALER OR JAYPRO SPORTS.
4) CAUTION: DO NOT OVER TIGHT THE CABLES, AS EXTREME LOADING WILL BE
PLACED ON THE WALL OR END STRUCTURE.
PRODUCT DESCRIPTION:
The BBC-SPDKT, cable suspended batting tunnel kit is designed to attach to your existing building
structure, whether steel I-beam columns or reinforced (blocked) studded walls. 9/16” holes will
need to be drilled for the ½” eyebolts. If attaching to standard CMU block or concrete filled walls it
is recommended that a wood stringer wall mounting kit be used (model number BBC-WLKT), which
can be purchased separately. This kit includes six (6) attractive polyurethane finished 24” long, 2” x
8” stringers and mounting plates that are easy to install and help spread the load across multiple
CMU blocks or other wall types.
The height of the suspending cables should be cut to a length of about 12” below the height of the
netting itself. This will allow about 12” of netting the lay on the floor to capture the ball.
To maximize the overall width of your cage and overcome the nature sag due to the weight of the
net, a reinforcement spreader kit is available (model number BBC-SCKT) that will hold the top rigid
and maintain the nets width.
Rev - B Page 2 of 13
ITEM
DESCRIPTION
BBC-SPDKT
1
1/4" GALVANIZED AIRCRAFT CABLE x 100 FT
3
2
1/2" x 6" STEEL EYEBOLTS, ZP
6
3
1/2" x 12" GALV. STEEL TURNBUCKLE, JAW TO JAW
3
4
3/8" QUICK LINK
3
5
1/4" THIMBLES
6
6
1/4" CABLE CLAMPS
12
7
1/4" x 2 3/8" SNAP HOOK
72
8
1/2"-13 HEX NUT
6
9
1/2" FLAT WASHER
12
10
1/2" ID SPLIT LOCK WASHER
6
11
1/8" GALVANIZED AIRCRAFT CABLE x 1500 FT
1
12
1/8" THIMBLES
144
13
1/8" CABLE CLAMPS
288
14
PLASTIC WIRE TIES - HEAVY DUTY
72
QTY
TOOLS REQUIRED:
(1) 7/16” and 5/16” Nut Drivers
(1) Box Wrench Set
(1) Electric drill w/ Phillips head
(1) Bolt Cutters
Unpack all parts and check against parts list to ensure that all have been included.
Inspect all parts for damage. Report any damages to the trucking company.
ASSEMBLY INSTRUCTIONS
Rev - B Page 3 of 13
1) Make up one end of each of the three cables, as shown in Figure 1. Tighten the
cable clamps using a 7/16” nut driver.
Figure 1: Assemble End Loops
2) Make up the other end of each cable leaving the cable clamps hand tight, as the
overall length may need to be adjusted.
3) Mark the location of the cable anchor as shown in the diagram below.
Anchor Point Locations On Building Wall (Both Ends)
Note: The height of the suspending cables should be set at about 12” below the height of the net.
This will place about 12” of net on the floor to capture the balls.
Rev - B Page 4 of 13
Loading...