Jabra LP 1000 User Manual

Installation Guide

LP 1000 Series

Ceiling Mount

Installation Guide

LP 1000 Series

Installationhandbuch zur

Deckenbefestigung

English. . . . . . . . . . . . .1

Deutsch . . . . . . . . . .13

010-0154-00

Copyright © 1998 by In Focu s, Inc.

Wilsonville, Oregon. All rights reserve d ..

Copyright © 1998 by In Focu s, Inc.

Wilsonville, Oregon, USA. Alle Rechte vorbehalten.

CEILING MOUNT INSTALLATION GUIDE

TM

The LP 1000 Series LiteMount

makes it easy to
hang your projector from the ceiling for fixed
installation use in meeting, auditorium and
training room settings.

You must determine the suitability of this prod­uct for your intended use and assume all risk
and liability in connection therewith. In Focus
recommends that a professional contractor or
other facilities professional assist you in mo unt­ing this device. Be sure to take precautions to
meet all local building codes.

Additional LiteMount Prod ucts

In Focus offers two additional LiteMount prod­ucts that may make your ceiling mount installa­tion easier.

•

The LiteMount False Ceiling Plate

SP-LTMT-PLT

(

) is designed for suspended ceil­ings with aco u sti c t ile s. It mo unt s in y our cei l­ing in place of a ceiling tile. It is pre-drilled
with holes to install the LiteMount brackets.

WARNING:

tion must be performed in
compliance with your local
building code require­ments. Local require­ments take precedence
over any instructions given
in this guide.

This installa-

•

The LiteMount Pipe Tubing Extension (

LTMT-EXT

) allows you to install the projector

SP-

in a room with a high ceiling. With the exten­sion, you can place the projector from 12”
(30.5) to 46” (117 cm) from the ceiling.

Contact your In Focus dealer to orde r these pr od­ucts.

Placing the Projector

Refer to the

LP 1000 User’s Guide

for image dis­tance, size, and angles of projection to determine
where to install the ceiling mount to meet your
projection needs.

1

Contents

NO TE:

The maximum
load the ceiling mount can
support is 50 pounds.

Contents

The LP 1000 Series Ceiling Mount package con­tains:

Installation Guid e

1

ceiling mount base box

2

dimensions: 11.6” x 10” x 1.5”
(29.5 x 25 x 3.8 cm)
weight: 3.5 lbs (1.6 kg)

projector mounting bracket

3

dimensions: 12” x 11.5” x 1.5”
(30.5 x 29.2 x 3.8 cm)
weight: 4.0 lbs (1.8 kg)

hardware for installing the projector mount-

4

ing bracket on the projector:

•

three (3) 4mm Phillips-head screws

•

three (3) 4mm quick release sleeves

•

one (1) 10/32 knurled knob screw

hardware for installing the projector (with

5

mounting plate) to the base box in the ceiling:

•

four (4) 6x12 mm knurled knob screws

•

two (2) 6 mm flat washers

•

two (2) 10 mm conical spacers

2

Install the Ceil ing Mou nt Base Box on the Ceil­ing

Instructions for installing the ceiling mount on
the LiteMount False Ceiling Plate and the Lite­Mount Pipe Tubing Exten sion are given in this
installation guide. If you have not purchased
either of these products, consult a professional
contractor or other facilities professional to
ensure a safe installation.

Please refer to the LiteMount False Ceiling Plate
and LiteMount Pipe Tubing Extension installa­tion instructions for lists of included hardware.

Center the ceiling mount base box on the ceil-

1

ing plate as shown in Figure 1. Make sure the
front of the base box faces forward toward
your projection screen. The front side of the
base box is the only surface without drilled
holes.

LiteMount False Ceiling Plate - Align the

2a

holes in the base box with the threaded studs
on the plate. Install the 4 washers and nuts as
shown in Figure 1.

WARNING

structure must be able to
support at least 5 times
the weight of the pr ojecto r
and mounting hardware. If
not, it must be reinforced
according to your local
building codes.

: The ceiling

LiteMount Pipe Tubing Extension - Line up

2b

the holes in the base box with the holes in the
plate at the end of the pipe extension. Install
the hardware as shown in Figure 2.

NOTE

: Refer to the
Installation Instructions
that came with the Lite­Mount False Ceiling Plate
and the LiteMount Pipe
Tubing Extension for
important additional infor­mation.

3

Install the Ceiling Mount Base Box on the Ceiling

Place the ceiling plate or pipe extension in the

3

ceiling so that the base box hangs down into
the room.

Route the projector’s cables through your

4

ceiling and out the hole in the ceiling

WARNING

dropped ceiling is an air-

handling plenum, be sure

the cables are plenum-

rated, or install the cables

: If the

within conduit.

(Figure 7).

surface faces front

make sure this

F

1

IGURE

Install the base box to the LiteMount False Ceiling Plate

4

make sure this

surface fac es front

F

IGURE

Install the base box to the LiteMount Pipe Tubing Extension

2

5

Attach the Mounting Plate to the Projector

Attach the Mounting Plate to the Projector

Set the projector on a table with the bottom

1

side up.
Insert the 3 screws into the 3 quick release

2

CAUTION

hardware that is provided

with the LP 1000 Series

different hardware may

damage your projector.

: Use only the

Ceiling Mount. Using

sleeves (Figure 3).
Attach the screws and sleeves to the holes in

3

the projector as shown in Figure 3. Be careful
not to over-tighten the bolts.

Align the keyholes in the mounting bracket

4

with the screws in the projector. Slide the
mounting bracket until the quick release
sleeves are at the top of the keyhole slot.

Attach the 10/32 knurled knob to the projec-

5

tor in the location shown in Figure 3.

quick release screws

knurled knob

goes here

F

3

IGURE

Attach the mounting plate to the projector

quick release screw

6