j5 create JUA310 User Manual [en, es, fr]
USB 3.0 Display Adapter
User Manual
Manuel de l'utilisateur
Bedienungsanleitung
Manual del usuario
Kullanma Kılavuzu
JUA310/330
ユーザー マニュア
使用手冊
JUA310/330
USB 3.0 Display Adapter
User Manual
JUA310/330 Manual
Table of Contents
INTRODUCTION .................................................................................................................... 3
GETTING STARTED –Notes for Before Installation ............................................................... 8
INSTALLATION FOR WINDOWS 8,7 .............................................................................. 9
INSTALLATION FOR WINDOWS XP .............................................................................. 18
INSTALLATION FOR MAC ............................................................................................ 27
FUNCTIONS INSTRUCTIONS: WINDOWS 8,7 ............................................................... 35
FUNCTIONS INSTRUCTIONS: WINDOWS XP ................................................................ 43
FUNCTIONS INSTRUTIONS: MAC ................................................................................. 49
TROUBLE SHOOTING .......................................................................................................... 53
TECHNICAL SUPPORT ......................................................................................................... 55
REGULATORY COMPLIANCE ............................................................................................. 56
WARRANTY OF j5 create ................................................................................................... 57
2
USB DISPLAY ADAPTER USER MANUAL
INTRODUCTION
Thank you for purchasing the j5 create (JUA310/330) USB 3.0 Display
Adapter! This adapter acts as an external video card for your MAC or PC.
It allows you to add an additional VGA/DVI(JUA310/330) monitor/display
through your USB 3.0 port. No need to open up the computer to add an
expensive video card, with the USB 3.0 Display Adapter you simply load
the drivers, plug in the adapter to the USB port, then plug in the VGA/DVI
monitor cable into the adapter and you are ready. The j5 create USB 3.0
Display Adapter supports three viewing modes. Primary mode, allows you
to have individual applications open on each monitor, vastly improving
productivity. Extended mode allows you to extend your desktop across
multiple displays, great for spreadsheets. Mirroring mode is used to clone
one screen onto another, ideal for presentations. With “Plug & Play”
functionality between your computer and 2nd monitor or projector, you
will be able to create a new visual environment in seconds.
In addition, j5 create has developed this compact design for the
sophisticated user who cares about function as well as elegance
Functions
Easily add an additional display instantly through the USB3.0 and
VGA/DVI connection.
Video playback performs at 1080P HD with a resolution of up to
2048 x 1152.
Add an additional monitor without adding an expensive, internal
video card, avoiding complicated installation
Hot swappable USB enables you to add or remove monitors
without rebooting your system
Move and view your large spreadsheets across two screens
without overlapping windows
Multitask with larger landscape/desktop space
Ideal for viewing multiple windows at the same time
Great for multitasking in a wide variety of applications including:
Phone centers, Stock Markets, Hospitals, Graphic Design, Editing,
Accounting, Etc.
A must have for surfing the web and working on your
email/facebook/twitter accounts all at the same time.
3
USB DISPLAY ADAPTER USER MANUAL
Highlighted Features
Supports display resolution:2048 x 1152 @ 32bit
Super Speed USB 3.0 up to 5 Gbit/s
Supports 1080P Video Playback
Plug-and-Play USB connectivity
Allows for up to 4 adapters in Windows
Allows for up to 2 adapters in Macs
Supports Display Modes: Primary, Extended, Mirror
Display Rotation: 0°, 90°, 180°, 270°
Aluminum enclosure that is non-toxic and recyclable
Easy driver install
Usage
Editor:
• Efficient editing of documentation on one screen and
researching reference materials on the other
Presentation:
• Use mirror mode while your laptop is plugged into a projector
through the USB 3.0 Display Adapter
• Use Primary mode to have two monitors and projector for
creative displays
Office:
• Dual display scenario: view large spreadsheets across 2 screens
with display continuity. (For example: Excel document)
• Independent: using desk space and doing multi-job at the same
time- increase efficiency.
• Read and reply to email on one screen and open
attachments on the other
Graphics Workstation:
4
• Design and check reference material at the same time.
• More space for tablets and photo/video editing
Entertainment:
• Watch TV/Movie while searching the program preview
• Play games online on one screen with the strategy guide on the
other screen
Stock Market Trading:
• Monitor multiple stock markets and market news simultaneously
Coding/Programming:
QTY
1~2 Dongle
3～4 Dongles
CPU
Intel 2 Quad 2.33 GHz or
above
Intel i5 3.10 GHz or above
RAM
2 GB or Higher
4 GB or Higher
Full HD
Video
Playing Video on the extended monitor
CPU: Intel Core i5 processor with 3.1 GHz or Higher
RAM: 4 GB memory or higher
※ Higher Processor recommended for Multi-Displays and
optimal performance.
Model: JUA 310
Interface
Host Interface
USB 3.0 Female Type-A Connector
Video Interface
VGA -DB 15 pin Female Connector
Power
USB DISPLAY ADAPTER USER MANUAL
• Allows effective code programming on one screen and software
program companion on the other screen.
Required Environments
Microsoft Windows8, 7, XP (32-bit or 64-bit) Compatible
Mac OS X Mt Lion/Lion/Snow Leopard Compatible
Available USB port ( USB 3.0 recommended)
Minimum System Requirements
Note:
USB HUB is not recommended for USB 3.0 display adapter
Note for Video Player:
*Windows 8 & 7 user: “Windows Media Player” is recommended for video
playback
* Windows XP & MAC user: Windows XP & MAC products are not supported by
USB 3.0 at this time, therefore we suggest USB 2.0 for ‘office application’ only;
Video Playback is not recommend due to USB 2.0 bandwidth limitations causing
limited video performance.
*Playing Video with multiple monitors: only “Media Player Classic” is supported.
Note:
To ensure that your device is equipped with the most current driver, please visit
our website at www.j5create.com and install the latest driver for this model.
Physical Specifications
5
Power Mode
Bus-powered or Self- Powered
Power Consumption
≦500mA
Physical Specification
Housing Material
Aluminum
Dimensions
Main body: 41(W)x 72(H)x14(D) mm
Cable length: 200 mm
Weight
Approximately 58 g
Model: JUA 330
Interface
Host Interface
USB 3.0 Female Type-A Connector
Video Interface
DVI-IFemale Connector
Power
Power Mode
Bus-powered or Self- Powered
Power Consumption
≦500mA
Physical Specification
Housing Material
Aluminum
Dimensions
Main body: 50(W)x 78.6(H)x15.25(D) mm
Cable length: 200 mm
Weight
Approximately 76 g
Aspect Ratio
Resolution
Color Depth
Wide Screen Display
16:9
2048 x 1152
16,32 bits
16:10
1920 x 1200
16,32 bits
16:9
1920 x 1080
16,32 bits
16:10
1680 x 1050
16,32 bits
16:9
1600 x 900
16,32 bits
16:10
1440 x 900
16,32 bits
16:9
1360 x 768
16,32 bits
16:10
1280 x 800
16,32 bits
USB DISPLAY ADAPTER USER MANUAL
Resolutions and Color Depth
6
15:9
1280 x 768
16,32 bits
16:9
1280 x 720
16,32 bits
Standard Display
4:3
1600 x 1200
16,32 bits
4:3
1400 x 1050
16,32 bits
5:4
1280 x 1024
16,32 bits
4:3
1280 x 960
16,32 bits
4:3
1152 x 864
16,32 bits
4:3
1024 x 768
16,32 bits
4:3
800 x 600
16,32 bits
USB DISPLAY ADAPTER USER MANUAL
Package Contents
USB 3.0 Display Adapter(JUA310/330)
Quick Installation Guide
Driver CD with E-Manual
7
USB DISPLAY ADAPTER USER MANUAL
GETTING STARTED –Notes for Before Installation
Install driver completely before inserting the USB 3.0 Display
Adapter USB Cable into your computer
Run the setup program as an administrator to avoid errors in
installation
Uninstall the previous driver first before updating the latest driver
Connect the VGA/DVI connector of USB Display Adapter to the
VGA/DVI cable of display device first before connecting to USB
port of computer
It is recommended to use an independent power supply for USB
Hub while multiple dongles are connected to the USB Hub
The display screen will flash during installation
8
USB DISPLAY ADAPTER USER MANUAL
INSTALLATION FOR WINDOWS 8,7
Device Driver Installation
This section illustrates the procedure for device driver installation for
Windows 7. To start, insert the Driver CD into your computer’s CD-ROM
drive. The setup program should be launched automatically. If Autorun
does not begin, go to “Computer”, Click on your optical drive, and
manually run the setup CD by double-clicking on “Setup.exe”
※Please make sure the USB cable of USB 3.0 Display Adapter is unplugged
from your PC or Notebook before executing the installation program.
1. The installation page will be launched. To start click on “ Install the
Latest Driver”. Please make sure the network is available or press “Install
Driver” to start the installation
9
USB DISPLAY ADAPTER USER MANUAL
2. After pressing the installation option, the InstallShield Wizard will launch,
click Next> to continue
3. Read the license agreement and check “I accept the terms of the
license agreement.” Click Next > to accept it and continue.
10
USB DISPLAY ADAPTER USER MANUAL
4. Driver installation proceeding…..
5. When Install Shield Wizard is complete, select “Yes, I want to restart my
computer now.” Click Finish to restart.
11
USB DISPLAY ADAPTER USER MANUAL
6. After rebooting connect the external display device (monitor/
projector) to the VGA/DVI connector of USB Display Adapter and turn
on the display device.
7. Connect the USB 3.0 Display Adapter into an available USB port of a PC
or Notebook, After Inserting the USB 3.0 Display Adapter into an USB
port, the “Installing device driver software” message will pop up.
If the Driver software was installed successfully the following message
should appear:
If you’re not going to install another USB 3.0 Display Adapter, restart your
PC. The functions of the USB 3.0 Display Adapter will be activated after
the computer restarted.
Multi USB 3.0 Display Adapter Installation
For installation of multiple USB 3.0 Display Adapters, during the “Install
Shield Wizard complete” step, select “No, I will restart my computer later.”
and click Finish to continue next step below
12
USB DISPLAY ADAPTER USER MANUAL
A. Connect all external display devices (monitor/ projector) to the
VGA/DVI connector of USB 3.0 Display Adapters and switch power on.
B. Connect the USB 3.0 Display Adapter into an available USB port of a
PC or Notebook.
After Inserting an USB 3.0 Display Adapter into a USB port, the systems
will automatically start the installation procedure and the prompt
message will pop-up on the task bar.
The Device driver software was installed properly,
if you are going to install more USB 3.0 Display Adapters, repeat step A& B
or restart computer.
The functions of the USB 3.0 Display Adapter will be activated after the
computer restarted. You might see the extend display shown on the
display device.
13
USB DISPLAY ADAPTER USER MANUAL
You can modify the corresponding position of each extend display via
display settings. Go to “START” → “Control Panel” → “Appearance and
Personalization” → “Adjust screen resolution”
※ Right-click on the desktop and go to “Screen Resolution”
When the ‘Screen Resolution’ window appears, each monitor’s number
can be identified by clicking “Identify.” Drag the monitor to the location
you want.
14
USB DISPLAY ADAPTER USER MANUAL
Verify Device Driver Installation
The following procedure helps you to verify the driver installation status of
the USB 3.0 Display Adapter.
Right-click “My Computer” “Manager” “Device Manager” click “+”
sign of “Sound, video and game controllers” & “Universal Serial Bus
controllers”
The picture below shows the installation process for a Single USB 3.0
Display Adapter
15
USB DISPLAY ADAPTER USER MANUAL
The picture below shows the installation process for a Multiple USB 3.0
Display Adapter
Device Driver Un-installation
※ Unplug the USB 3.0 Display Adapter before un-installing the driver.
1. Click “Start”→ Control Panel → Programs and Feature→ Uninstall or
Change a Program Select j5 VGA/DVI DISPLAY ADAPTER ... Click
Uninstall
16
USB DISPLAY ADAPTER USER MANUAL
2. A message will appear asking if you want to remove the selected
application. Click ‘ok’ to continue.
3. Driver un-installation proceeding….
4. When the driver uninstall is completed select “Yes, I want to restart my
computer now.” Click Finish to restart.
17
USB DISPLAY ADAPTER USER MANUAL
INSTALLATION FOR WINDOWS XP
Device Driver Installation
This section illustrates the procedure for device driver installation for
Windows XP. To start, insert the Driver CD into your computer’s CD-ROM
drive. The setup program should be launched automatically. If Autorun
does not begin, go to “Computer”, Click on your optical drive, and
manually run the setup CD by double-clicking on “Setup.exe”
※Please make sure the USB 3.0 Display Adapter USB cable is unplugged
from your PC or Notebook before executing the installation program.
1. The installation page will be launched. To begin installation click on
“ Install the Latest Driver” , please make sure the network is available or
press “Install Driver” to start the installation
18
USB DISPLAY ADAPTER USER MANUAL
2. After pressing the installation option, the InstallShield Wizard will launch,
click Next> to continue
3. Read the license agreement and check “I accept the terms of the
license agreement.” Click Next > to accept it and continue.
19
USB DISPLAY ADAPTER USER MANUAL
4. Driver installation proceeding…..
5. When Install Shield Wizard is complete, select “Yes, I want to restart my
computer now.” Click Finish to restart.
20
USB DISPLAY ADAPTER USER MANUAL
6. After your computer is rebooted, connect the external display device
(monitor/ projector) to the VGA/DVI connector of USB 3.0 Display
Adapters and turn it on.
7. Connect the USB 3.0 Display Adapter into an available USB port of a PC
or Notebook, After Inserting the USB 3.0 Display Adapter into an USB
port, the “Installing device driver software” message will pop up.
An icon ( ) will be seen on the lower right toolbar.
The message pictures below shows Driver software is installed
successfully.
If you’re not going to install another USB 3.0 Display Adapter, restart your
PC. The functions of the USB 3.0 Display Adapter will be activated after
the computer restarted.
21
USB DISPLAY ADAPTER USER MANUAL
Multi-USB 3.0 Display Adapter Installation
For installation of multiple USB 3.0 Display Adapters, during the “Install
Shield Wizard complete” step, select “No, I will restart my computer later.”
and click Finish to continue next step below
A. Connect all external display devices (monitor/ projector) to the
VGA/DVI connector of USB 3.0 Display Adapters and switch power
on.
B. Connect the USB 3.0 Display Adapter into available USB port of PC
or Notebook.
After Inserting an USB 3.0 Display Adapter into a USB port, the systems
will automatically start the installation procedure and the prompt
message will pop-up on the task bar.
The Device driver software was installed properly, if you are going to install
more USB 3.0 Display Adapters, repeat step A & B or restart computer
22
When Display Properties
windows appears, each
monitor’s number can be
identified by clicking “
“ identify”
Drag the monitor to the
location you want.
USB DISPLAY ADAPTER USER MANUAL
The functions of the USB 3.0 Display Adapter will be activated after the
computer restarted. You might see the mirror display shown on the display
device.
You can modify the corresponding position of each extend display via
display settings.
Go to “START” → “Control Panel” → “Appearance and Personalization” →
“Display Properties” →“Settings”
Note:
If your internal graphics card is Dual Display Ports…..
1. When using one USB 3.0 Display Adapter
The display device which connected to the 2nd VGA/DVI port will be
numbered 3rd monitor, the display device which connected to the USB
3.0 Display Adapter will be numbered 2nd monitor.
2. When using two USB 3.0 Display Adapter
The display device which a port to the 2nd VGA/DVI port will be
numbered 4th monitor, the display device which connected to the USB
3.0 Display Adapter will be numbered 2nd and 3rd monitor and so on…
23
USB DISPLAY ADAPTER USER MANUAL
Verify Device Driver Installation
The following procedure helps you to verify the driver installation status of
USB 3.0 Display Adapter
Right-click “My Computer” “Manager” “Device Manager” click “+”
sign of “Display Adapter” & “Universal Serial Bus controllers”
The picture below shows the installation process for a Single USB 3.0
Display Adapter
24
USB DISPLAY ADAPTER USER MANUAL
The picture below shows the installation process for a Multiple USB 3.0
Display Adapter
Device Driver Un-installation
※Unplug the USB 3.0 Display Adapter before un-installing the driver
1. Click “Start”→ Control Panel → Programs and Feature→ Uninstall or
change a program Select j5 DISPLAY ADAPTER... Click Uninstall
25
USB DISPLAY ADAPTER USER MANUAL
2. Confirm windows will pop out, Click to continue.
3. Driver un-installation proceeding….
4. When the driver uninstall is completed select “Yes, I want to restart my
computer now.” Click Finish to restart.
26
USB DISPLAY ADAPTER USER MANUAL
INSTALLATION FOR MAC
Device Driver Installation
Installing the device driver enables your computer’s operating system to
recognize the USB 3.0 Display Adapter. Be sure that you are referring to
the appropriate installation procedure before you begin installing.
※ Make sure the USB cable of USB 3.0 Display Adapter is unplugged from
your Mac Desktop or Mac Notebook before executing the setup program.
This section illustrates the device driver installation procedure for a
computer running Snow Leopard.
1. Insert the Driver CD into the CD-ROM drive
2. The installation page will be launched; To begin installation click on
start “ Get Last Driver online” , please make sure the networking is
available or Choose the OS version you are using and press “Install
Driver” to start the installation
27
USB DISPLAY ADAPTER USER MANUAL
3. Click “Continue” to proceed
4. Click “Continue” to proceed
28
USB DISPLAY ADAPTER USER MANUAL
5. Type in your password and click “OK”
6. Click “Continue Installation”
29
Loading...