Its telecom VME-4000 User Manual

Download

VME - 4000

Aut o Att enda nt & Voice Mail System

Installation and Programming Ma nu al

Version 7.1 April 2005 Proprietary

NOTICE

This publication refers to the VME - 4000 Voice Mail System, Release 7 Additional copies of this manual may be obtained from Alee n Technologies Reproduction of this

manual or parts thereof without written permission from Aleen Technologies is strictly prohibited. Aleen Technologies reserves the right to modify the hardware and software described herein

without prior notice. However, changes made to the hardware or software described do not necessarily render this publication invalid.

WARRANTY

In the event that the product proves to be defective in workmanship or materials within a period of one year from date of shipment, Aleen Technologies shall repair or replace the same at its discretion. Transportation will be the responsibility of the dealer/distributor.

Under no circumstances shall Aleen Technologies be liable for consequential or special damages, loss of revenue or user/dealer expenses arising out of or in connection with the use or performance of the product, whether base on contract, tort or any other legal agreement.

The fol lo win g s hal l v oi d t h e a bo ve w ar ra nt y : m alf u nc ti on s r es ul ti ng f ro m fi re , acc id en t, neglect, abuse or acts of God; use of improper electrical power; or repair of, tampering with or alteration of the product by anyone other than Aleen Technologies authorized

Table of Contents

1 Introduction...................................................................................................1-1

1.1. Manual Audience and Contents.............................................................1-1

2 General Description......................................................................................2-1

2.1. General..................................................................................................2-1

2.1.1. System Features .......................................................................2-2

2.1.2. Automated Attendant Features..................................................2-3

2.1.3. Voice Mail Features...................................................................2-6

2.2. The Basic System Description ...............................................................2-7

2.3. Physical Description...............................................................................2-9

2.3.1. Side Panel.................................................................................2-9

2.3.2. Front Panel..............................................................................2-10

2.4. Technical Specifications.......................................................................2-11

3 Installation.....................................................................................................3-1

3.1. General..................................................................................................3-1

3.2. Unpacking..............................................................................................3-1

3.3. Installing the Unit ...................................................................................3-1

3.3.1. Expanding the System to 4 Ports (VM-128 Only)......................3-3

4 DTMF Programming......................................................................................4-1

4.1 General..................................................................................................4-1

4.2 Entering and Exiting the Programming Mode.........................................4-1

4.3 First Time Programming.........................................................................4-1

4.3.1 Defining PBX Parameters..........................................................4-2

4.3.2 Setting the Time and Date.........................................................4-8

4.3.3 Programming the Operational Modes........................................4-8

4.4 Programming the Unit..........................................................................4-11

4.4.1 Creating Mailboxes..................................................................4-11

4.4.2 Creating Mailbox Groups.........................................................4-12

4.4.3 Notification...............................................................................4-13

4.4.4 Programming the Automated Attendant Script Menu ..............4-16

4.4.5 Recording Script Messages.....................................................4-16

Voice Mail and Auto Attendant System Installation and Programming Manual i

Table of Contents

4.4.6 Programming Script Messages ...............................................4-17

4.4.7 Directory Listing Programming ................................................4-23

4.4.8 Resetting Script Message Programming to Default.................4-23

4.4.9 Supervised, Semi-Supervised and Non-Supervised Transfers4-24

4.5 Additional Features..............................................................................4-26

4.5.1 Changing Passwords...............................................................4-26

4.5.2 Activate Flash Memory Force Reorganize...............................4-27

4.5.3 Changing to/from Day Light Saving Time................................4-27

4.5.4 Changing the Operational Mode..............................................4-28

4.5.5 Playing a System Message.....................................................4-28

4.5.6 Playing All System Messages .................................................4-28

4.5.7 System Message Setting.........................................................4-29

4.5.8 Listening to the Software Version Number..............................4-29

4.5.9 Resetting the System ..............................................................4-29

4.5.10 Adjusting Recording Length....................................................4-29

5 Switching to Computer Programming ........................................................5-1

5.1. General..................................................................................................5-1

5.2. Connecting the Unit to the Computer.....................................................5-1

5.3. System Requirements............................................................................5-2

5.4. Installing the VMS..................................................................................5-2

5.5. Starting VMS..........................................................................................5-3

5.5.1. Communication Setup...............................................................5-4

6 VMS Programming........................................................................................6-1

6.1. General..................................................................................................6-1

6.2. File Menu...............................................................................................6-1

6.2.1. Open..........................................................................................6-1

6.2.2. Save..........................................................................................6-2

6.2.3. Save As.....................................................................................6-2

6.2.4. Open Default .............................................................................6-2

6.2.5. Print Settings Menu...................................................................6-3

6.2.6. Print...........................................................................................6-3

6.2.7. Print Preview .............................................................................6-3

6.2.8. Print Setup.................................................................................6-4

6.2.9. Options......................................................................................6-4

Voice Mail and Auto Attendant System Installation and Programming Manual ii

Table of Contents

6.2.10. Exit ............................................................................................6-5

6.3. Communication Menu............................................................................6-6

6.3.1. Read Parameters ......................................................................6-6

6.3.2. Send Parameters.......................................................................6-7

6.3.3. Read Recording ........................................................................6-8

6.3.4. Send Recording.........................................................................6-9

6.3.5. Backup ....................................................................................6-11

6.3.6. Restore....................................................................................6-11

6.3.7. System Init...............................................................................6-12

6.3.8. Password.................................................................................6-12

6.3.9. ComPort..................................................................................6-13

6.4. Parameters Menu ................................................................................6-13

6.4.1. PBX Parameters......................................................................6-13

6.4.2. System Parameters.................................................................6-19

6.4.3. In-Band DTMF Protocol...........................................................6-20

6.5. Auto-Attendant Menu...........................................................................6-21

6.5.1. Script Menu.............................................................................6-21

6.5.2. Time, Date and Weekly Schedules..........................................6-27

6.6. Voice Mail Menu ..................................................................................6-32

6.6.1. List of Mailboxes ......................................................................6-32

6.6.2. Notification Parameters...........................................................6-36

6.6.3. Groups of Mailboxes................................................................6-37

6.7. Line Monitor Menu ...............................................................................6-38

6.7.1. Activate the Line Monitor.........................................................6-38

6.8. Statistics Menu.....................................................................................6-39

6.8.1. General....................................................................................6-39

6.9. Wizard Menu........................................................................................6-40

6.10. Help Menu...............................................................................6-41

7 User Operation Instructions ........................................................................7-1

7.1. General..................................................................................................7-1

7.2. User’s Main Menu..................................................................................7-1

7.3. Retrieve Message Menu........................................................................7-2

7.4. Mailbox Parameters...............................................................................7-2

7.4.1. Record Greeting........................................................................7-3

Voice Mail and Auto Attendant System Installation and Programming Manual iii

Table of Contents

7.4.2. Record Name............................................................................7-3

7.4.3. Directory Listing.........................................................................7-4

7.4.4. Change Password.....................................................................7-4

7.4.5. Do Not Disturb (DND)................................................................7-4

7.4.6. External Notification...................................................................7-5

7.4.7. Pager Notification......................................................................7-6

7.4.8. Return to Previous Menu...........................................................7-6

7.5. Send Message.......................................................................................7-6

7.6. Return to Auto Attendant........................................................................7-7

7.7. Quick Reference Guide..........................................................................7-7

8 Programming the In-Band DTMF Protocol .................................................8-1

8.1. General..................................................................................................8-1

8.2. Programming the Unit by Telephone......................................................8-1

8.2.1. Defining an In-Band DTMF Code for an Event..........................8-2

8.2.2. Selecting an Operation Type.....................................................8-3

8.2.3. Selecting a destination ..............................................................8-4

8.2.4. Defining the Time to Wait for the First DTMF Character............8-4

8.2.5. Defining the Time to Wait Between DTMF Characters..............8-4

8.2.6. MATRA PBX Support................................................................8-5

8.3. Sample Programming ............................................................................8-5

8.3.1. Working with the SIEMENS Hicom 150E Office PBX................8-5

9 Troubleshooting............................................................................................9-1

9.1. General..................................................................................................9-1

9.2. Troubleshooting Guide...........................................................................9-1

10 Programming Commands..........................................................................10-1

11 Programming Forms...................................................................................10-1

12 System Messages.......................................................................................10-1

12.1. General ..............................................................................................12-1

12.2. System Messages..............................................................................12-1

12.3. Numbers.............................................................................................12-2

12.4. Dates..................................................................................................12-3

12.5. Months ...............................................................................................12-3

12.6. General Messages.............................................................................12-4

Voice Mail and Auto Attendant System Installation and Programming Manual iv

Table of Contents

List of Figures

Figure 2-1: General View........................................................................................2-1

Figure 2-2: VM-128 Mbx Unit Upgrading ................................................................2-8

Figure 2-3: Unit With Cover Removed....................................................................2-9

Figure 2-4: Unit Side Panel.....................................................................................2-9

Figure 2-5: Unit Side Panel...................................................................................2-10

Figure 3-1: Analog Line Connections......................................................................3-2

Figure 3-2: Analog Line Connections......................................................................3-3

Figure 5-1: RS-232 Cable Connection....................................................................5-2

Figure 5-2: COM Port Selection Window................................................................5-3

Figure 5-3: Product Type Window...........................................................................5-3

Figure 5-4: Main Screen .........................................................................................5-4

Figure 5-5: Communication Menu...........................................................................5-4

Figure 6-1: File Menu..............................................................................................6-1

Figure 6-2: Product Type Window...........................................................................6-1

Figure 6-3: Open Window.......................................................................................6-2

Figure 6-4: Save As Window ..................................................................................6-2

Figure 6-5: Print Settings Menu ..............................................................................6-3

Figure 6-6: Print Window ........................................................................................6-3

Figure 6-7: Print Preview Window...........................................................................6-4

Figure 6-8: Print Setup Window..............................................................................6-4

Figure 6-9: Options Window – Toolbar Configuration Tab......................................6-5

Figure 6-10: Options Window – File Location Tab..................................................6-5

Figure 6-11: Communication Menu.........................................................................6-6

Figure 6-12: Read Parameters Window..................................................................6-6

Figure 6-13: Send Parameters Window..................................................................6-7

Figure 6-14: Password Window..............................................................................6-7

Figure 6-15: Read Recording Window....................................................................6-8

Figure 6-16: List of Scripts to be Read Window......................................................6-9

Figure 6-17: Send Recording Window....................................................................6-9

Figure 6-18: List of Scripts to be Sent Window.....................................................6-10

Figure 6-19: Backup Window................................................................................6-11

Voice Mail and Auto Attendant System Installation and Programming Manual v

Table of Contents

Figure 6-20: Restore Window ...............................................................................6-11

Figure 6-21: System Init Window..........................................................................6-12

Figure 6-22: Change Password Window...............................................................6-12

Figure 6-23: COM Port Selection Window............................................................6-13

Figure 6-24: COM Port Selection Window............................................................6-13

Figure 6-25: PBX Parameters Window – Extensions Tab.....................................6-14

Figure 6-26: PBX Parameters Window – Call Transfer Tab..................................6-15

Figure 6-27: PBX Parameters Window – Supervision Tab ...................................6-16

Figure 6-28: PBX Parameters Window – CP Tone & Disconnect Tab..................6-18

Figure 6-29: System Parameters Window ............................................................6-19

Figure 6-30: In-Band DTMF Protocol Window......................................................6-20

Figure 6-31: Auto-Attendant Menu........................................................................6-21

Figure 6-32: Script Menu Window – Script Programming Tab..............................6-21

Figure 6-33: Script Menu Window – Dial a String Tab..........................................6-24

Figure 6-34: Script Menu Window – Script Opening Tab......................................6-25

Figure 6-35: Script Menu Window – Script Recording Tab...................................6-26

Figure 6-36: Script Menu Window – Script Status Tab .........................................6-26

Figure 6-37: Time & Date Window........................................................................6-27

Figure 6-38: Time & Date Window........................................................................6-28

Figure 6-39: Auto Window – Weekly Schedule Tab..............................................6-29

Figure 6-40: Auto Window – Auto Breaks Tab......................................................6-30

Figure 6-41: Auto Window – Holiday Schedules Tab............................................6-31

Figure 6-42: Voice Mail Menu...............................................................................6-32

Figure 6-43: List of Mailboxes Window – List Tab.................................................6-32

Figure 6-43: New Mailbox Window – Mailbox Parameters Tab ............................6-33

Figure 6-45: List of Mailboxes Window – Parameters Tab....................................6-35

Figure 6-46: Notification Parameters Window.......................................................6-36

Figure 6-47: Notification Parameters Window.......................................................6-37

Figure 6-48: Notification Parameters Window.......................................................6-38

Figure 6-49: Line Monitor Window........................................................................6-38

Figure 6-50: Statistics Menu .................................................................................6-39

Figure 6-51: List of Messages Window.................................................................6-39

Figure 6-52: Wizard Menu ....................................................................................6-40

Figure 6-53: Wizard Window.................................................................................6-40

Voice Mail and Auto Attendant System Installation and Programming Manual vi

Table of Contents

Figure 6-54: Help Menu........................................................................................6-41

Figure 6-55: Help Topics Window.........................................................................6-41

Figure 7-1: Quick Reference Guide ........................................................................7-7

Voice Mail and Auto Attendant System Installation and Programming Manual vii

Table of Contents

List of Tables

Table 4-1: PBX Parameter Commands...................................................................4-3

Table 4-2: Time and Date Commands....................................................................4-8

Table 4-3: Operational Modes Commands .............................................................4-9

Table 4-4: Mailbox Creation Commands...............................................................4-12

Table 4-5: Mailbox Creation Commands...............................................................4-13

Table 4-6: Program Notification for Mailboxes Commands...................................4-15

Table 4-7: Recording Script Messages Commands..............................................4-16

Table 4-8: Detection Commands ..........................................................................4-24

Table 4-9: Transfer Modes Programming Commands..........................................4-25

Table 8-1: Entering an In-Band DTMF Code Using a Telephone............................8-2

Table 10-1: DTMF Programming Commands.......................................................10-1

Voice Mail and Auto Attendant System Installation and Programming Manual viii

Introduction

Chapter 1: Introduction

1.1. Manual Audience and Contents

The Auto Attendant and Voice Mail System Installation and Operation Manual is intended for System Installers and Administrators, responsible for the installation, setup and programming of the units.

NOTE



Please read this manual before installation, programming and operation of the Auto Attendant and Voice Mail System.

The information in this manual is valid for the following device:  VME-4000– Voice Mail 128 mail boxes (VM – 128 Mbx) Note that the only differences between these units are:

The term “unit” in this manual refers to both devices, unless specifically stated otherwise.

Voice Mail and Auto Attendant System Installation and Programming Manual 1-1

Introduction

This manual contains the following:

Chapter Heading

1 Introduction 2 System Description 3 Installation 4 DTMF Programming 5 Programming by Computer 6 VMS Programming 7 User Operating Instructions 8 Programming the In-Band

Protocol

9 Troubleshooting 10 Programming Commands 11 DTMF Programming Forms 12 System Messages

Voice Mail and Auto Attendant System Installation and Programming Manual 1-2

General Description

Chapter 2: General Description

2.1. General

The Voice Mail and Automated Attendant is a small stand-alone multilingual system for organizations of sixteen and sixty-four employees (VM 128 Mbx). The unit incorporates state of the art technology, including DSP, flash memory and SMT production.

Figure 2-1: General View

The VME-4000– VM-128 Mbx is available with 2 or 4 ports and up to 128 mailboxes. It provides up to 10 hours of recording time.

The unit can be integrated with most types of PBXs through the analog ports or through the RS-232 serial port.

The system administrator can be programmed by the computer using the Voice Mail System Maintenance Software Utility Program (VMS) or by touch-tone telephone.

The unit installation is quick and easy: Just mount it on a wall next to the PBX and connect it to the SLT interfaces and to the main power supply with an external power adapter.

The unit is ready for use immediately after the system administrator completes the setup procedure of integration parameters, mailboxes, notification type,

Voice Mail and Auto Attendant System Installation and Programming Manual 2-1

General Description

system schedules and opening greetings. Mailbox owners can then set up their own personal mailbox parameters.

The unit is a powerful Voice Mail System at an affordable price. It contains most useful features and services provided by PC-based systems but at a lower cost. The unit’s features can be divided into three groups:

• System administration

• Automated attendant

• Voice mail.

2.1.1. System Features

The system has the following features:

• Configuration The Voicemail/Auto Attendant system VM-128 (VME-4000) is available with

2-ports and 10 hours of recording time. The system administrator can upgrade the unit by adding a 2-port expansion card to the motherboard to provide 4ports.

• Programming

The system administrator can program the unit by:

− Touch-tone telephone using DTMF tones

− Computer using the Voice Mail Maintenance Software Utility Program

(VMS). The installer should save the files containing the parameters set in each installation.

• Integration with your PBX

The system administrator can integrate the unit with the PBX through:

− In-Band DTMF Protocol integration using DTMF strings. This type of integration is achieved by setting up the communication parameters on the PBX and the units, including answering a call, transfer, recall from busy, recall from no answer, the notification parameters and more.

− Out-band integration through a serial port (RS-232) applying the PBX parameters to the unit. This type of integration must be developed separately for each type of PBX.

• Loop Current Disconnection Some PBXs have the capability, which enables them to notify the unit through

the line interface when a call is terminated. When the Voice Mail detects this situation, the line is disconnected and the unit is then ready to receive another call.

Voice Mail and Auto Attendant System Installation and Programming Manual 2-2

General Description

• Message Notification The unit automatically notifies the mailbox owner of new messages in

different ways according to the system configuration. Notification may be local (to a PBX extension) or remote (to a telephone at a remote location, a cellular telephone or a pager).

• Security Passwords

The unit supports three types of passwords:

− System Administrator. 4-8 digits password. Gives access to all data stored

in the unit.

− Operator. 4 digits password. Gives access to the operating modes of the

system. The available operating modes are: Day, Night, Break and Holiday.

− Mailbox. 4 digits password. Gives access to individual mailboxes.

Mailbox owners can change the password at any time.

• Line Monitor The unit sends all incoming DTMF codes to the VMS from all the ports,

simultaneously through the RS-232 cable. The line monitor is a powerful tool to simplify the integration and installation of the unit with the PBX.

2.1.2. Automated Attendant Features

The unit’s automated attendant answers incoming calls and through a series of recorded menus and telephone directories, helps the callers reach the required extensions.

• Opening Greeting The unit plays a pre-recorded greeting to callers. The opening greeting usually

includes the organization’s name, how to reach an extension, department or operator, how to switch languages, how to leave a message and to access a directory.

During the greeting, callers can access a department by dialing a single digit, dialing the extension number or holding for assistance.

• Operating Modes Depending on the time and the system schedule, the unit answers external

calls with one of four opening greetings:

− Day Mode During normal business hours, the unit answers calls with a pre-recorded

daytime greeting. The daytime greeting enables the caller to reach a requested extension, mailbox, department, and directory or to switch languages.

Voice Mail and Auto Attendant System Installation and Programming Manual 2-3

General Description

− Night Mode During non-working hours, the unit answers calls with a pre-recorded

nighttime greeting that enables the caller to leave a message in a requested mailbox.

− Holiday Mode During holidays, the unit answers calls with a special greeting that enables

the caller to leave a message in a specific mailbox or in the operator’s mailbox.

− Break Mode (Multi Breaks) The system administrator can program parts of the day mode as break

time. During break time, the unit answers calls with a special greeting that enables the caller to leave a message in a specific mailbox or in the operator’s mailbox. You can program up to 10 breaks .

• System Schedules (Auto-Mode) If your organization has operating hours that vary from day to day, the system

administrator can define the daily operating schedules on a weekly basis, including daytime, nighttime and break time hours. When the Auto mode is activated, the unit automatically switches between the day, night and break modes according to the pre-defined schedule.

The operator can override the pre-defined system schedule and switch manually to day, night, break, or holiday mode using a password.

• Holiday Schedules The unit switches automatically to Holiday mode on dates programmed as

holidays. During holidays the unit answers calls with the special holiday greeting.

• Fax Detection If the unit detects a fax tone (CNG) during the opening greeting, it

automatically transfers the call to the pre-defined fax extension.

• Directory Listing (Dial By Name) The unit can provide a list of mailbox owner names. The directory listing

enables calls to be transferred to all extensions configured within the list. A caller can access the directory listing by following instructions during the opening greeting.

In order to enable a directory listing call transfer, the mailbox owner must record his name and a three-letter code. A caller can reach the proper extension after dialing the respective code and verifying a correct extension according to the mailbox owner’s name.

The system administrator enables two methods of directory listing: according to the mailbox owners first or last name.

Voice Mail and Auto Attendant System Installation and Programming Manual 2-4

General Description

• Call Transfer The system administrator can program the unit to detect the Call Progress tone

and DTMF signals sent by the PBX and transfer the calls to extensions in one of the following modes:

− Non-Supervised The unit transfers the call immediately without verifying the status of an

extension.

− Supervised The unit checks for a busy or answer signal before transferring the call to

an extension.

− Semi-Supervised The unit only checks for a busy signal before transferring the call to an

extension.

• Multilingual Option The unit can operate in three languages simultaneously. The system

administrator can configure each mailbox to operate in one of the three selected languages. The caller can select the language in which the system messages (prompts) are played.

• Answering on the First Ring To avoid delays, the system administrator can set up the unit on each

individual port to answer incoming calls on the first ring.

• Script Menus The unit supports up to 39 script menus. A script menu is a recorded

announcement that can accept a digit entry (0-9) during playback. Based on the digit entered, the unit can take one of the following actions:

• Transferring the call to another script menu

• Transferring the call to another script menu and change the language

• Transferring the call to an extension or hunt group

• Transferring the call to a mailbox

• Dialing a string of DTMF (20 different strings and up to 20 digits for each

string including special characters)

• Retrieving messages from a mailbox

• Disconnecting the line

• Leaving a message

• Playing the directory listing

Voice Mail and Auto Attendant System Installation and Programming Manual 2-5

General Description

2.1.3. Voice Mail Features

The unit enables a caller to leave a message, recorded in his own voice, in any mailbox. The mailbox owner can access his mailbox at any time from any touchtone telephone and listen to his messages. Mailbox owners can also modify their own mailbox parameters. Up to 47 messages (new and saved) can be stored in the mailbox.

• Real/Virtual Mailboxes The unit supports up to 128 real and virtual mailboxes. A real mailbox has a

telephone extension, whereas a virtual mailbox does not.

• Personalized Mailboxes Mailbox owners can personalize their mailboxes by recording a personal

greeting, assigning a personal password to the mailbox and setting optional parameters.

• Personal Greeting Mailbox owners can record or change personal greetings at any time from any

touch-tone telephone. Callers first hear the personal greeting of the extension called and then they can leave a message.

• Day and Time Stamp The system administrator can program the unit to indicate the start of each

message and the day and time it was recorded.

• Message Deletion Mailbox owners can manually delete messages or the system administrator

can program the unit to automatically delete all messages after a specified number of days.

• Message Forwarding Mailbox owners can forward copies of messages to other mailboxes or

mailbox groups. Mailbox owners can also record an introduction to the forwarded message.

• Message Reply Mailbox owners can reply directly to a message and record a message in the

sender’s mailbox.

• Pause During Message Retrieval Mailbox owners can pause the playback of the mailbox messages.

• Mailbox password back out key Mailbox owners can be routed to the Main Company Greeting from the

System request to enter the mailbox’s password.

• Mailbox Groups A caller can send a message to all the members of a mailbox group at one

time.

Voice Mail and Auto Attendant System Installation and Programming Manual 2-6

General Description

All defined mailboxes belong to the “All Group” mailbox group. In addition, the system administrator can create up to four mailbox groups, each containing up to twenty mailboxes. Mailboxes can belong to more than one group and can be added to or deleted from a mailbox group by the system administrator. Each mailbox group can be assigned with a mailbox group greeting.

• Do Not Disturb Mode Mailbox owners can set their mailboxes in the Regular Mode or Do Not

Disturb Mode. When a caller dials a Do Not Disturb extension using the Automated Attendant menus, the unit plays a special “Do Not Disturb” menu and does not transfer the call to the extension.

• Individual Language Selection The system administrator can select one of the languages supported by the

unit. When the mailbox owner or caller enters the mailbox, the unit automatically switches to the selected language.

• Adjustable Recording Length The system administrator can select the length of all recorded messages in the

unit. The selected length will control the following types of messages: scripts, greetings, names and incoming messages. Changing this parameter will affect the operation unit.

• Automatic Gain Control (AGC) When this feature is enabled, the unit automatically adjusts the line volume so

incoming messages will be recorded at the same level.

2.2. The Basic System Description

The unit is a digital system consisting of the following:

• Sophisticated DSP voice-processing device

• Flash memory for storing voice recording and parameter data

• Central Processing Unit

• 2- or 4-ports analog extensions line interface

• Real-time clock

The unit provides two major services:

• Automated Attendant Uses menus and sub-menus to transfer calls to specific departments,

extensions or mailboxes.

• Voice Mail Receives and delivers messages. Each mailbox has its own number and

mailbox owners have passwords enabling them access to their mailboxes.

Voice Mail and Auto Attendant System Installation and Programming Manual 2-7

General Description

Messages can be saved, deleted or transferred to other mailboxes. Mailbox owners can also send identical messages to groups of mailboxes or to all the mailboxes in the system.

By configuring the following, the unit’s Automated Attendant and Voice Mail can be customized to suit the company requirements:

• PBX parameters

• Automated Attendant script menus and customized “Busy”, “No Answer” and

“Do Not Disturb” menus in up to three different languages simultaneously.

• Voice Mail features include: mailboxes, mailbox groups and various types of

message notifications for each mailbox

The VME-4000 (VM-128 Mbx) comes with two lines and 10 hours recording time. You can upgrade the unit by adding a 2-port expansion card to the motherboard to provide four lines.

Figure 2-2: VM-128 Mbx Unit Upgrading

Voice Mail and Auto Attendant System Installation and Programming Manual 2-8

General Description

2.3. Physical Description

The functional components of the unit are located under the side panel cover. The LEDs are on the left side of the front panel. The bottom panel has two indented holes for wall mounting.

Figure 2-3: Unit With Cover Removed

2.3.1. Side Panel

No. Connector Function

1 Power Supply Connector Connects the unit to the external power

2 RS-232 Connector Connects the unit to the PBX or a PC 3 2 RJ-11 Sockets Connects the unit to 2 or 4 PBX

Figure 2-4: Unit Side Panel

supply

extensions (VME-4000-VM-128 Mbx,)

Voice Mail and Auto Attendant System Installation and Programming Manual 2-9

General Description

2.3.2. Front Panel

Figure 2-5: Unit Side Panel

The following table describes the function of the four LEDS on the front panel.

Status Day Night Holiday Auto

Day Mode: Manual On Off Off Off

Night Mode: Manual

Holiday Mode: Manual

Break Mode: Manual

Day Mode: Auto Night Mode: Auto Break Mode: Auto System Error System Error

System Error

Automatic Self-Test On On On On

Please contact your local dealer.

Off

On Off Off

Off On Off

On On Off Off

On Off Off On Off On Off On On On Off On Off Flashing Off Off Flashing Flashing Flashing Flashing Flashing Flashing Flashing Off

Voice Mail and Auto Attendant System Installation and Programming Manual 2-10

General Description

2.4. Technical Specifications

The technical specifications of the unit are as follows:

DC Power Supply 9VDC/800mA Line Voltage 24 to 72VDC DC Leakage Current On-hook Insulation Resistance

between Line Terminal and the Ground

Ring Capacitor On-hook Impedance Ring Detect 27 to 100VAC/16 to 60Hz DC Resistance (off-hook) Impedance (off-hook) Imbalance Ratio 300 to 3400Hz > 46dB Return Loss 300 to 3400Hz > 18dB Current during Break DTMF Transmission: Frequency Tolerance +1.5% Frequency Level (High Group) -6 to -8 dBm

> 10µA 0 to 100VDC > 5MΩ

100 to 200VDC > 30KΩ 500 VAC/50Hz > 20KΩ 100 VAC/25Hz > 100KΩ

0.47µF ± 10% @ 50VDC, 40 VAC/25Hz > 3000Ω

24 to 66VDC @ 20 to 100mA 100 to 350Ω 300 to 3400Hz 500 to 700Ω

< 700µA

Frequency Level (Low Group) -8 to -10 dBm Inter-digit Pause in Tone Dialing 70 to 80ms Fax CNG Tone Detection 1100Hz ± 38Hz

Voice Mail and Auto Attendant System Installation and Programming Manual 2-11

Installation

Chapter 3: Installation

3.1. General

The unit is delivered completely assembled. It is designed for mounting on a wall close to the PBX.

3.2. Unpacking

Before unpacking, inspect the package. If you notice any damage, immediately report it to your local dealer.

 To unpack the unit:

1. Place the package on a flat surface and open it.

2. Remove the contents of the package and place them on a clean surface.

3. Remove all packing material.

4. Inspect the contents. if you notice any physical damage, report it to you local dealer immediately.

3.3. Installing the Unit

 To install the unit:

1. Mount the unit on a wall close to the PBX cabinet. Use the drill template

to place the two screws.

2. Remove the side panel cover.

3. Connect the RJ-11 connector on one end of the cables to the RJ-11 sockets on the side panel of the unit. Connect the other end of the cables to one or two analog telephone lines on the Main Distribution Frame

NOTE



Each RJ-11 socket on the side panel of the unit can support up to two analog telephone lines (VME-4000 only - VM–128 Mbx).

(MDF) of the PBX (see Figure 3-1).

Voice Mail and Auto Attendant System Installation and Programming Manual 3-1

Installation

Figure 3-1: Analog Line Connections

4. On the side panel of the unit, plug the 9 VDC adapter jack into the power supply connector.

5. Plug the 9 VDC adapter into the main power supply outlet to turn the unit on. The LEDs on the front panel turn on and off, one after another and then the LED indicating the status of the unit turns on.

6. If your PBX supports a full-authorized RS-232 integration with the unit, connect one end of the RS-232 cable to the unit’s RS-232 connector and the other end to the RS-232 connector of the PBX.

7. Call each unit line from any extension and verify the answer. You should hear the default greeting (system message no. 000. See Chapter

12).

8. Replace the side panel cover.

9. Program the unit according to your PBX type and required applications.

Voice Mail and Auto Attendant System Installation and Programming Manual 3-2

Installation

Figure 3-2: Analog Line Connections

3.3.1. Expanding the System to 4 Ports (VME-4000,VM-128 Only)

The 2-port expansion kit contains:

• 2-port expansion card

• 4-wire cable

• 2 plastic spacers.

 To install the expansion card:

1. Disconnect all external cables and connectors.

2. Remove the 9 VDC adapter power plug from the main power supply outlet to turn the unit off.

3. Open the unit’s top cover by unscrewing the four screws.

4. Place the two plastic spacers into the corresponding holes.

5. Insert the expansion card into the corresponding J6 connector.

6. Connect one end of the 4-wire cable to J5 on the motherboard and the other end to J5 on the expansion card.

7. Replace the top panel cover and plug the 9 VDC adapter into the main power supply outlet to turn the unit on.

8. Reconnect all the external cables and connectors to the unit. Voice Mail automatically detects four lines when it is turned on.

Voice Mail and Auto Attendant System Installation and Programming Manual 3-3

DTMF Programming

Chapter 4: DTMF Programming

4.1 General

You can program the unit using:

 A telephone – by means of DTMF tones  A computer – by means of the designated Voice Mail Maintenance software

(see Chapters 5 and 6).

NOTE



4.2 Entering and Exiting the Programming Mode



You will hear a confirmation tone every time you enter a programming command.

NOTE

The unit is unable to handle calls when in the programming mode.

 To enter the programming mode:

1. Connect a PBX analog line to the unit.

2. Call the PBX analog line from any touch-tone telephone.

3. Wait until the unit answers and plays the opening menu.

4. Dial *900.

5. Dial the System Administrator’s password (default: 1234) to enter the programming mode.

 To exit the programming mode:

Dial *900 or do not dial any number for a consecutive one minute.

NOTE



If you exit the programming mode by dialing *900, the unit plays the opening menu. You can then check the changes that were made to the system.

4.3 First Time Programming

When programming a unit for the first time, follow this checklist:

1. Call from a touch-tone telephone to the unit. You will hear the default message (system message 000 – see Chapter 12).

2. Dial *900 and the administrator password (default: 1234) to enter the programming mode.

3. Set the PBX parameters according to Paragraph 4.3.1 to ensure the proper operation of the unit with your PBX.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-1

DTMF Programming

4. Set the unit’s real-time clock according to Paragraph 0.

5. Set the system schedule according to Paragraph 4.3.3.

6. Create mailboxes according to Paragraph 4.4.1.

7. Define a notification type for each mailbox according to Paragraph 4.4.3.

8. Define notification parameters (i.e. message light on and message light off and interval between ring notification) according to Paragraph 4.4.3.3.

9. Record and program script menus for the Automated Attendant according to Paragraph 4.4.4. Make sure you define the mailboxes before building Automated Attendant script menus.

4.3.1 Defining PBX Parameters

To integrate the unit with your PBX, apply the PBX parameters to the unit. To obtain your current PBX parameters, check your PBX User’s Manual or the current PBX setup configuration.

To configure the unit to detect the in-band DTMF protocol sent by your PBX, refer to Chapter 7.

NOTE



Do not forget to enter programming mode by dialing *900 and the administrators password before using the programming commands.

Table 4-1 presents the commands you must enter to apply the PBX parameters to the unit.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-2

DTMF Programming

Table 4-1: PBX Parameter Commands

Operation Command Default

Extension size

Cut off time for continuous call progress tone detection

No. of rings before the line is answered

Time to wait for No-Answer

Legal PBX Extensions

*300 + X where X is a digit 1-4 You can only change this parameter if mailboxes and/or legal extensions have not yet been defined.

*301 + X

where: X = cut off time in seconds (0-9)

*310 + line number + number of rings

Line number = 1-4 Number of rings = 1-9

*311 + XX where XX is 00-99 seconds. This code is applicable only when supervised transfer is selected.

*320 + Y + First Ext. + Last Ext. + # where Y is a group number (0-9). Example: *320 0 330 350 # *320 1 355 375 # You can define up to 10 groups of legal extensions. If a caller dials an extension by direct dialing (code 170), The unit checks if the extension is legal. If the extension is not legal, The unit does not transfer the call.

6 seconds

20 seconds

None

Resetting a group *320 + Y + 000 + 000 + # (the two groups of

zeros can be 2, 3, or 4 digits long, according to

the extension size) Resetting all groups Operator ID Code

*320 + #

*330 + X

0 where X is a digit 0-9 When the caller dials this digit during any script message, the call is transferred to the operator.

Programmable code for retrieving messages

Voice Mail and Auto Attendant System Installation and Programming Manual 4-3

*331 + X X = 0-9; Retrieve digit

DTMF Programming

Operation Command Default

Disconnection Code

*333 + CODE

+ #

### The unit terminates a call when it receives the

disconnection code. The code can include up to four digits. Legal values for this code can be any combination of 0-9, *, #, and A-D.

Clear Disconnection Code

External Access Code

Clear External Access Code

Pause before and after external access code

Transfer mode for all extensions

Day operator, Night operator, Fax and Supervisor’s extension numbers

* 333 + #

*340 + X + #

where X is up to 4 digits external access code (legal entries 0-9, ABCD, ), Pause (*1). This code is applicable for external notification.

*340 + #

*341 + X

where X is the length of the pause in seconds (0-

*350 + X + Y

X = 1; All extensions except the operator X = 2; Operator extension only Y = 0; Non Supervised Y = 1; Supervised Mode Y = 2; Semi Supervised mode

*360 + X + YYYY + #

where: X = 1; Day operator X = 2; Night operator X = 3; Fax extension X = 4; Supervisor extension

One mailbox can be defined as Supervisor. When storage memory reaches 80% of its capacity, a message is sent to this mailbox indicating the situation.

YYYY = Corresponding extension number.

2 seconds

Non supervised

–

Delete the extension assignments

*360 + X + #

where: X = 1; Day operator X = 2; Night operator X = 3; Fax extension X = 4; Supervisor extension

Volume level

*369 + X

5 where: X = volume level (0-9); 9 = Loudest

Voice Mail and Auto Attendant System Installation and Programming Manual 4-4

DTMF Programming

Operation Command Default

Flash-1

*370 + XXX where XXX is a 3-digit number (000-980) in steps of 20 ms. Example: *370 300 sets Flash-1 to 300 ms

Flash-2 Flash-2 is fixed at 1200 ms.

Flash-2 is used in some PBX’s for Recall from No-Answer or Busy Codes.

Busy, Disconnect and DTMF Off/On time

*371 + X + YYYY

where: X = 0; incoming minimum DTMF length (00003000 ms)(Note: DTMF, which is shortly that

defined with this command will be ignored by VM during greetings recording process)

X = 1; busy off (0100-3000 ms) X = 2; busy on (0100-3000 ms) X = 3; Disconnect off (0100-3000 ms) X = 4; Disconnect on (0100-3000 ms) X = *; DTMF off (0000-3000 ms) X = #; DTMF on (0000-3000 ms) YYYY = Cadence in milliseconds in steps of 20 milliseconds.

600 ms

1200 ms

100 ms

500 ms

240 ms

200 ms

60 ms

Length of the DTMF cadence sent by the PBX, e.g. a Disconnect code

Note: This parameter is needed to calculate the time, which must be truncated from the end of the message, which is terminated via the Disconnect code.

Busy Signal Cadence Check

*372 + X

where X is the length of the DTMF cadence in ms (0-9). Each step represents 100ms

Note: By setting this parameter to 2, the Voice Mail will cut 200 ms from the end of the recording.

*375 + XXXX + # where XXXX is a busy extension number. Check the busy signal by dialing the busy extension number and playing the busy cadence values.

100 ms

Voice Mail and Auto Attendant System Installation and Programming Manual 4-5

DTMF Programming

Operation Command Default

Voice and DTMF Sensitivity

Automatic Gain Control (AGC)

DTMF amplitude

Procedural codes sent to the PBX in order to perform a specific task

*376 + X + Y

X = 1; Voice sensitivity level X = 2; DTMF sensitivity level Y = Sensitivity level (0-9) The volume at which the unit detects voice when the called extension answers or the volume level at which the unit detects DTMF throughout its operation.

Note: The higher the sensitivity level, the higher the sensitivity to voice or DTMF.

In order to activate the new selection, a new call must be initiated.

*377 + X

X = 0; AGC disabled X = 1; AGC enabled When enabled, The unit will adjust the incoming messages volume to a set volume level. Note: For the new value to take affect, a new call must be initiated.

*379 + X

where X = volume level (1-9), 9 = Loudest

*380 + X + CODE

+ #

X = 1; LED1 notification code X = 2; LED2 notification code X = 3; LED notification off code X = 4; Transfer code X = 5; Recall from Busy X = 6; Recall from No Answer

CODE

= Respective PBX code

Enabled

None

Flash 1 + Ext

Flash 1

Delete a specific procedural code

*380 + X + #

X = 1; LED1 notification code X = 2; LED2 notification code X = 3; LED notification off code X = 4; Transfer code X = 5; Recall from Busy X = 6; Recall from No Answer

Define a free DTMF string, that can be dial from the Auto Attendant to the PBX

Answer number of samples

*381 + XX + YY…YY + #

X = String number (00-19) YY…YY = DTMF string

Note: See also command *121

*386 + X

where:

3.3

X = number of samples (0-9)

Voice Mail and Auto Attendant System Installation and Programming Manual 4-6

DTMF Programming

CODE

DTMF Character Number to Dial

Digits 0-9 0-9 * ** Extension *0 Pause *1, indicates a 1 second pause Hook Flash 1 *2 Hook Flash 2 *3

# *4 A *5 B *6 C *7 D *8

Voice Mail and Auto Attendant System Installation and Programming Manual 4-7

DTMF Programming

4.3.2 Setting the Time and Date

Table 4-2 presents the commands used to set the unit time and date.

NOTE



Table 4-2: Time and Date Commands

Make sure to enter programming mode by dialing *900 and the administrator’s password before using the programming commands.

Operation Command

Setting the time and day of the week

Setting the date

Listening to the system time

*420 + HH + MM where HH = hour (00-23) MM = minutes (00-59) Example:*420 15 25 stands for 3:25 p.m.

*430 + DD + MM + YY where DD = date of the month (01-31) MM = month (01-12) YY = year (00-99) Example:*430 15 03 97 March 15, 1997

Note: 00 represents Year 2000. The day of the week is automatically calculated

by the system, based on the entered date.

*440 The system announces the date and time.

4.3.3 Programming the Operational Modes

The unit can operate in Day, Night, Break, or Holiday mode. If the unit is in the Auto mode, it automatically changes modes according to programmed schedules.

NOTE



Voice Mail and Auto Attendant System Installation and Programming Manual 4-8

Do not forget to enter programming mode by dialing *900 and the administrator’s password before using the programming commands.

DTMF Programming

Table 4-3: Operational Modes Commands

Operation Command

Selecting an Operational Mode

Selecting time stamp format (Used by English and Chinese languages only)

Setting the Working Time (for Auto mode only)

*400 + X

where X stands for the operational mode. Day mode = 0 (default mode) Night mode = 1 Holiday mode = 2 Auto mode = 3 Break mode = 4

*410 + X

where X = 0 means the time stamp is in 12-hour format (default) X = 1 means the time stamp is in 24-hour format

*450 + D + hh:mm + hh:mm where D is the day of the week (1-7)

First hh:mm = start of work time in 24 hour format Second hh:mm = end of work time in 24 hour format

Repeat for all days of the week. Example: *450 1 08 30 1700 means that the unit will

play the Day mode opening greeting on Monday from 8:30 until 17:00. It will play the Night mode opening greeting the rest of the time.

: Day 1 is Monday.

Setting the Breaks Time (for Auto mode only)

*460 + X + Y + hh mm + hh mm + SS, where

X - Day of the week 1-7, 1 for Monday Y – Break number 0-9 SS – Script number hh mm – start and stop of break time in 24 format

Voice Mail and Auto Attendant System Installation and Programming Manual 4-9

DTMF Programming

Operation Command

Entering annual holiday dates (For Auto mode only)

Delete all holidays on a specific date

Delete all holidays on a specific month

Delete all holidays

*470 + DD + MM + hh:mm + hh:mm

where: DD = Day of the month (01-31) MM = month (01-12) hh:mm = Start time; Hour and minutes in 24 hour format hh:mm = End time; Hour and minutes in 24 hour format

Repeat for holidays Example 1: *470 02 12 08 15 23 45

The unit will play the Holiday mode opening greeting on December 2

, from 8:15 until 23:45.

*470 + DD + MM #

where: DD = Day of the month (01-31) MM = month (01-12)

*470 + ** + MM + # MM = month (01-12)

*470 + #

External Notification Active Time

*490 + hh:mm + hh:mm

where: hh:mm = Start time; Hour and minutes in 24 hour format hh:mm = End time; Hour and minutes in 24 hour format

Example 1: *490 09 00 20 00 The will activate the External Notification between 9 a.m. to 8 p.m.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-10

DTMF Programming

4.4 Programming the Unit

4.4.1 Creating Mailboxes

You can define up to 128 mailboxes. The numbers of the mailbox and its extension are identical. Make sure that the number of digits in the mailbox number conforms to the number of digits in an extension (*300).

You can select one of the languages supported by the unit for each mailbox. After selecting a language, the unit performs the following:

 Plays all menus in the selected language.  Plays all system messages (e.g., time stamp and error messages) in the

selected language.

 If ring or remote notification is enabled, the mailbox owner is notified in the

selected language.

A virtual mailbox can also be created for users who do not have extensions. When a caller dials a virtual mailbox number on the Automated Attendant menu, the call is immediately transferred to the Do Not Disturb menu and the caller is given the option to leave a message.

You may use the external notification features for the virtual mailboxes. Do not select internal notification because virtual mailboxes do not have extensions.

You can assign a mailbox for announcing messages without the ability to record incoming messages. This mailbox is called an Announcer mailbox. All mailboxes can be changed from a regular mailbox to an announcer mailbox and vice versa at any time.

NOTE



Do not forget to enter programming mode by dialing *900 and the administrator’s password before using the programming commands.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-11

DTMF Programming

Table 4-4: Mailbox Creation Commands

Operation Command

Creating a range of mailboxes Creating one mailbox Selecting an announcer mailbox

*500 + First Mailbox + Last Mailbox + # *501 + Mailbox Number + # *502 + XXXX + Y + #

where: XXXX = existing mailbox number Y = 0; Regular mailbox (default) Y = 1; Announcer mailbox

Deleting a mailbox

*510 + Mailbox Number + # Make sure to remove any transfer to the mailbox from the Automated Attendant scripts before deleting the mailbox.

Creating a range of virtual

*520 + First Mailbox + Last Mailbox + #

mailboxes Creating one virtual mailbox Defining whether to play or skip

the time and date stamp during message playback for a range of mailboxes

*521 + Mailbox Number + # *530 + First Mailbox + Last Mailbox + B + #

where B = 0; Play the date and time stamp (default) B = 1; Skip the date and time stamp

Defining whether to play or skip the time and date stamp during message playback for one mailbox

*531 + Mailbox Number + B + # where B = 0; Play the date and time stamp (default) B = 1; Skip the date and time stamp

Defining a language for a range of mailboxes

*532 + First Mailbox + Last Mailbox + Z + #

where Z = 1, 2 or 3 (language number)

Defining a language for a mailbox

*533 + Mailbox Number + Z + #

where Z = 1, 2 or 3 (language number)

4.4.2 Creating Mailbox Groups

You can create up to four mailbox groups for distributing messages. Each mailbox group can contain up to twenty mailboxes. The group numbers are by default 000, 001, 002 and 003. Group 099 consists of all mailboxes (real and virtual).

You can select a different number for the first digit of the mailbox groups using code *545. Make sure that you select a number that does not interfere with your PBX’s numbering plan.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-12

DTMF Programming

NOTE



Table 4-5: Mailbox Creation Commands

OPERATION COMMAND Adding a mailbox to a group *540 + Group Number + Mailbox Number + #

Do not forget to enter programming mode by dialing *900 and the administrator’s password before using the programming commands.

Note: You must define the mailbox before adding it to a group.

Changing the number of the first digit in the mailbox groups

Deleting a mailbox from a group Resetting a group

NOTE



You can record a separate greeting message can be recorded for each mailbox group.

4.4.3 Notification

The unit notifies the mailbox owner of new messages in different ways according to the system configuration. Notification may be local or remote.

NOTE



Notification is always done on the second line.

4.4.3.1 Local Notification

*545 + X

where X is the first digit of the mailbox groups. Default is 0.

*550 + Group Number + Mailbox Number + # *560 + Group Number

Note: Resetting a group removes all the mailboxes within

that group.

For local notification, you can select one of the following options:

 None. The notification feature is disabled.  Message Light On 1. The unit signals the PBX that a mailbox has received a

message. The PBX then turns on the message light of the telephone extension. If the Message Light Off code is programmed, the code is transferred to the PBX after the mailbox owner retrieves all his new messages.

 Some PBXs do not support the Message Light Off code. Instead they turn the

message light off when the mailbox owner presses the message button on his proprietary telephone set and the unit starts playing the messages (see Table

 Message Light On 2. Same as Message Light On 1 but used only for PBXs

that have two different codes for different telephones or for special tone notification (see Table

Voice Mail and Auto Attendant System Installation and Programming Manual 4-13

4-1).

DTMF Programming

The system administrator can set the notification method to one of two states (code *760):

 Notification on first new message  Notification on every new message  Sign Rings. The unit rings the notified extension number. These Sign Rings

may be sent at programmed intervals (code *720). The unit stops sending Sign Rings after the mailbox owner retrieves all his new messages or the maximum number of retries has been made (code *750).

 Rings. The unit rings the notified extension for a programmed time period

(code *730). When the mailbox owner answers, the unit prompts him to enter his password. After entering the password, the mailbox owner may retrieve his messages. If the mailbox owner does not answer, the unit tries again at programmed intervals (code *720). The unit stops sending Ring notifications after the mailbox owner retrieves all his new messages or the maximum number of retries has been made (code *750).

4.4.3.2 Remote Notification

The mailbox owner may choose to be notified at a remote location (i.e. his mobile telephone, home telephone or pager) by entering a remote telephone number (of up to 20 digits) or pager number (of up to 40 digits). You can use any combination of *, #, A-D, 0-9, and Pause when setting the remote notification telephone number.

After remote notification is enabled, the unit will dial the remote phone or pager number and notify the mailbox owner of any new messages. After entering the password, the mailbox owner can retrieve his messages. The duration of remote notification rings is programmed using code *730.

The unit stops sending Ring notifications after the mailbox owner retrieves all his new messages or the maximum number of retries has been made (code *750). The mailbox owner must obtain permission from the System Administrator to enable remote notification. The System Administrator must use code *710 or *711 to grant permission.

The remote notification activation time can be programmed so the administrator can decide on the daylights hours for the external notification to be activated. The time span of this service is programmed using code *490.

When permission has been granted and the mailbox owner enables remote notification, the unit first dials the external access digits (programmed using code *340) and then dials the mailbox owner’s remote telephone or pager number.

NOTE



Make sure that you enter the remote telephone or pager number before enabling remote notification.

Notification is always done on the second line.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-14

DTMF Programming

4.4.3.3 Setting Notification for Mailboxes

Table 4-6: Program Notification for Mailboxes Commands

Setting local notification for a range of mailboxes

Disable local notification for all mailboxes

Setting local notification for one mailbox

NOTE



Do not forget to enter programming mode by dialing *900 and the administrator’s password before using the programming commands.

Virtual mailboxes do not have extensions and may not be configured for internal notification.

OPERATION COMMAND

*700 + First Mailbox + Last Mailbox + X + #

where X = 0; notification is disabled X = 1; Message Light On 1 is selected X = 2; Message Light On 2 is selected X = 3; Sign Rings is selected X = 4; Rings is selected

*700 + #

*701 + Mailbox + X + #

where X is defined as above

Permitting remote notification for a range of mailboxes

Disable remote notification for all mailboxes

Permitting remote notification for one mailbox

Ring Notification Interval

Ring Notification Duration

Maximum number of days to store messages

*710 + First Mailbox + Last Mailbox + Y + # where Y = 0; remote notification is not permitted Y =1; remote notification is permitted

*710 + #

*711 + Mailbox + Y + #

Y = 0; remote notification is not permitted Y = 1; remote notification is permitted

*720 + XX where XX is a 2 digit number in minutes (1-99). Default = 30 minutes

*730 + X where X = 0; stands for short time for rings (default) X = 1; stands for long time for rings

*740 + XX where XX stands for number of days (00-99). 00 = Messages are not deleted by Voice Mail.

Time to wait after off-hook for notification dialing

Voice Mail and Auto Attendant System Installation and Programming Manual 4-15

*741 + X

X = Time in seconds (0-9)

DTMF Programming

OPERATION COMMAND

Number of Ring Notification retries

*750 + XX where XX refers to the number of ring notification attempts. Default is 05.

Activate the LED notification

*760 + X where X = 0; for 1

new message (Default)

X = 1; for every new message.

4.4.4 Programming the Automated Attendant Script Menu

The unit supports up to 21 script messages (00-20) for building the Automated Attendant menu. The unit also supports another six script messages in three languages (21-26 for the first language, 31-36 for the second and 41-46 for the third) for Busy menu, No Answer menu, Do Not Disturb menu and Post Recording menu.

The opening scripts for each line are selected by command *112. The following numbers are dedicated by default to specific script messages:

 Script message number 00 to the Day Mode Opening Menu  Script message number 10 to the Night Mode Opening Menu  Script message number 15 to the Break Time Opening Menu  Script message number 20 to the Holiday Mode Opening Menu.

The rest of the script messages (01-09, 11-14 and 16-19) may be used in all modes without limitations. Each script message has three parts:

 Script message number  Recorded announcement  Programming that indicates the action to be taken when a caller dials one digit

(0-9) or dials nothing during an announcement.

4.4.5 Recording Script Messages

Table 4-7 describes how to record script messages.

Table 4-7: Recording Script Messages Commands

OPERATION COMMAND Recording a script message Playback a script message

*100 + XX + Beep + Record + # *101 + XX

Deleting a script message

Voice Mail and Auto Attendant System Installation and Programming Manual 4-16

*102 + XX

DTMF Programming

NOTE



XX is script message 00-26, 31-36 and 41-46.

4.4.6 Programming Script Messages

You can program each script message separately. The programming command format for script messages is:

* + Command Code + XX + B + YY + #

Where: Command Code defines the action that should be taken when B is pressed

during playback of script message XX. XX = a script message number. B = the digit dialed by the caller during playback of script message XX or at the

end of the message. B can be 0-9 or * (for end of message). YY = the destination, which can be an extension, mailbox or another script

message.

NOTE



Do not define the Operator ID digit on script messages.

The command codes used to build the Automated Attendant Script Menu are presented on the following pages. You can program one of the following actions for each script message:

 Play another script message  Return to the opening menu  Play another script message and change the language  Transfer the call to an extension  Transfer the call to the operator  Transfer the call to a mailbox  Disconnect the line  Leave a message in a mailbox  Retrieve messages from a mailbox  Direct dial to an extension  Transfer a call directly to a mailbox  Dial a free DTMF string  Place a call on hold  Blind Transfer to the busy extension  Play the directory listing

Voice Mail and Auto Attendant System Installation and Programming Manual 4-17

DTMF Programming

Technicians and System Administrators should program the script messages according to the application.

4.4.6.1 End Of Message Timeout

Sets the EOM timeout period for each script individually.

Command: *105 + XX + Y + # Where: XX = Script number Y = Timeout in seconds Example: *105 05 6 # The unit sets the EOM timeout to 6 seconds for script message 05.

4.4.6.2 Play Another Script Message

Builds submenus by transferring the caller from one script message to another.

Command: *110 + XX + B + YY + # Example: *110 00 3 02 # The unit plays script message 02 when “3” is dialed during playback of script

message 00.

NOTE



Make sure to record script message 02.

4.4.6.3 Select Opening Script

Selects the opening script message.

Command: *112 + XX + YY + Z + # XX = Default script number 00,10,15 or 20 YY = Replacement script number 00-20 Z = Line number 1-4

4.4.6.4 Transfer to the Main Company Greeting

Transfers the caller to the Main company greeting’s menu. Used mainly by Busy and No-Answer script messages (21-24 for the first language, 31-34 for the second language and 41-44 for the third language), where the caller is given the option to return to the main menu.

Command: *115 + XX + B # Example: *115 21 5 # The unit plays the opening menu when “5” is dialed during playback of script

message 21.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-18

DTMF Programming

4.4.6.5 Transfer to a Script Message and Change the Language

Changes the system language and plays another script message. The unit supports up to three system languages simultaneously (factory loaded).

Command: XX = The current script message B = The digit dialed by the caller during playback of script

YY = The destination script message Z = The system language digit (1, 2 or 3) Example: *117 00 7 01 3 # The unit changes to the third language and plays script message 01 when “7” is

dialed during playback of script message 00.

NOTE



Make sure that script message 01 has been recorded in the appropriate language.

*117 + XX + B + YY + Z + #

message XX

4.4.6.6 Select the Default Language

The unit can su p p o r t up to t h r ee l an g ua g e s . The default language is the language the unit automatically uses if no other language has been selected. To change the default language, dial *900 and the administrator password to enter the programming mode, then dial:

Command: Z = 1 is the first language (default) Z = 2 is the second language Z = 3 is the third language

NOTE



The available languages are listed on the bottom panel of the unit.

*118 + Z + #

4.4.6.7 Transfer the Call to an Extension

Transfers the caller to an extension or department (hunt group). The designated extension number may contain up to 4 digits and does not have to

be in the range of legal extensions. Command: Example 1: *120 05 3 123 # The unit transfers the call to extension 123 when “3” is dialed during playback of

script message 05. Example 2: *120 00 * 1000 #

*120 + XX + B + extension number + #

The unit transfers the call to hunt group 1000 at the end of script message 00.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-19

DTMF Programming

4.4.6.8 Dialing a Programmed DTMF String from the AutoAttendant Script

Dialing a programmed DTMF string from the Auto-Attendant script.

Command: *121 + XX + B +YY+ # Y = The DTMF string number (00-19)

See also command *381

4.4.6.9 Transferring the Call to the Operator at the End of the Script Message

Transferring the call to the operator at the end of the script message: The unit transfers the call in supervised, semi-supervised or non-supervised mode depending on code *350.

Command: *125 + XX + # Example: *125 00 # The unit transfers the call to the operator at the end of script message 00.

4.4.6.10 Transferring the Call to a Mailbox

Transferring the caller to a specific mailbox number: The mailbox must be defined and existing.

Command: *130 + XX + B + Mailbox number + # Example: *130 01 5 152 # Transfers the call to mailbox 152 when “5” is dialed during playback of script

message 01.

4.4.6.11 Disconnecting the Line

Disconnects the call at the end of the script message or if the caller dialed the disconnect digit during playback.

This command may include the system message 001.

Command: *140 + XX + B + Z + # Z = 0; means disconnect the line with no message. Z = 1; means disconnect the line with the above system

message Example: *140 10 * 1 # The unit plays the disconnection message and then disconnects the call at the end

of script message 10.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-20

DTMF Programming

4.4.6.12 Leaving a Message in a Mailbox

Initiates the procedure for leaving a message in a mailbox.

Command: *150 + XX + B + # Example: *150 00 8 # The unit asks for a mailbox number when “8” is dialed during playback of script

message 00. After dialing the requested mailbox number, the caller hears the mailbox’s greeting and can leave a message.

4.4.6.13 Retrieving Messages from a Mailbox

Initiates the procedure for retrieving messages from a mailbox.

Command: *160 + XX + B + # Example: *160 00 9 # The unit asks for a mailbox number and password when “9” is dialed during

playback of script message 00. After dialing the requested mailbox number and password, the mailbox owner can retrieve his messages and access the user menu to record a personal greeting, change his password, etc.

4.4.6.14 Directing a Call to an Extension

Enables the caller to dial an extension directly by programming the first digit of the extension. When a caller dials the first digit of an extension during playback of a script message, the unit stops the message and waits for the rest of the digits of the extension. The number of digits in an extension is defined by code *300. You can enter up to four different digits.

Command: *170 + XX + first digit(s) + # Example 1: *170 00 2 # The unit waits for the rest of the extension number when “2” is dialed during

playback of script message 00. After the caller dials the rest of the extension number, the unit transfers the call to the extension.

Example 2: *170 00 2 4 # Same as Example 1, except the extension number starts with 2 or 4 (for extension

numbers 2xx and 4xx).

Voice Mail and Auto Attendant System Installation and Programming Manual 4-21

DTMF Programming

4.4.6.15 Transferring a Call Directly to a Mailbox

Transfers the call directly to a mailbox number. This feature is similar to directly dialing an extension, except the call is transferred directly to a mailbox. You can enter up to four different digits.

Command: *175 + XX + first digit(s) + # Example 1: *175 00 2 # The unit waits for the rest of the mailbox number when “2” is dialed during

playback of script message 00. After the caller dials the rest of the mailbox number, the unit transfers the call to the mailbox.

Example 2: *175 00 2 4 # Same as Example 1, except the mailbox number starts with 2 or 4.

4.4.6.16 Placing a Call on Hold

Gives the caller the option to remain on hold. Valid only for script messages 2122 (for the first language), 31-32 (for the second language) and 41-42 (for the third language), which are reserved for the extension Busy menus.

Command: *180 + XX + B + # Example: *180 21 3 # The unit places the call on hold for 10 seconds before trying to transfer the call

again when “3” is dialed during playback of script message 21.

4.4.6.17 Blind Transfer to a Busy Extension

Transfers a call in blind mode to a busy extension. Valid only for script messages 21-22 (for the first language), 31-32 (for the second language) and 41-42 (for the third language), which are reserved for the extension Busy menus.

Command: *185 + XX + B + # Example: *185 21 5 # The unit immediately tries to transfer the call again when “5” is dialed during

playback of script message 21.

NOTE



Both Place a Call on Hold and Blind Transfer to a Busy Extension are used to transfer calls to a busy extension. Place a Call on Hold gives the option to retry every 10 seconds to transfer the call until the extension is available.

In a Blind Transfer, calls are transferred to a Busy Extension immediately. This option is used when the unit is connected to a PBX that incorporates In-Band DTMF signaling.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-22

DTMF Programming

4.4.7 Directory Listing Programming

The directory-listing feature (Dial By Name) allows calls to be transf erred to proper extensions based on recorded names and codes of mailbox owners. The Directory Listing parameters are set through the commands explained in the following paragraphs.

4.4.7.1 Directory Listing Format

Changes the format of the directory listing. The unit supports two directory listing formats.

Command: *011 + X X = 0; List according to last name (Default) X = 1; List according to first name

4.4.7.2 Transferring to Directory Listing

Transfers the call to the directory listing. Command: *111 + XX + B + #

XX = Script number Example: *111 00 5 # Play the directory listing when “5” is dialed during playback of script message

00.

4.4.8 Resetting Script Message Programming to Default

Resets a complete script message or only one entry. This command does not delete the recorded script message.

Resetting a complete script message:

Command: *190 + XX + # Example: *190 03 # Resets script message 03 to its default values.

Resetting a single entry in a script message: Command:

*190 + XX + B + # Example: *190 02 5 # Resets entry 5 in script message 02 to its default value.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-23

DTMF Programming

Default values:

 0-9. If a caller dials a digit that has not been programmed (or set to default)

during playback of a script message, the unit plays “This entry is not supported” and repeats the script message.

 If the caller dials the Operator ID code, the call is forwarded to the operator

extension regardless of script message programming.

 At the end of a script message. If the caller does not dial a number during

playback of a script message, the unit disconnects the call at the end of the message.

4.4.9 Supervised, Semi-Supervised and Non-Supervised Transfers

Transfer to an extension may be supervised, semi-supervised or non-supervised. In a supervised mode, the unit detects Busy and No-Answer signals from the PBX. In a semi-supervised mode, the unit only detects Busy signals. In a nonsupervised mode, the unit transfers a call to the required extension without checking the status of the extension.

You can configure the unit to detect Answer, Busy and Do Not Disturb signals by recognizing the DTMF codes sent by the PBX or analyzing the Call Progress tones.

If DTMF signals are selected for the supervised mode, you must define DTMF codes for the Answer, Busy and Do Not Disturb conditions.

NOTE



Table 4-8: Detection Commands

Do not forget to enter programming mode by dialing *900 and the administrator’s password before using the programming commands.

Operation Command

Selecting DTMF code or Call Progress tone detection

*220 + X

where X = 0; Supervised call transfer using Call Progress tones (default) X = 1; Supervised call transfer using DTMF codes

Defining the DTMF code for the Answer condition, Busy condition and Do Not Disturb condition

*221 + X + CODE

X = 1; Answer condition X = 2; Busy condition X = 3; Do Not Disturb condition CODE

= DTMF code sent by the PBX for the Transfer

Supervision operation 0-9,*,#,A-D See page 26 for the proper codes

+ #

Delete all DTMF condition

*221 + #

codes

Voice Mail and Auto Attendant System Installation and Programming Manual 4-24

DTMF Programming

Operation Command

Delete all DTMF condition

*221 + #

codes Delete the DTMF code for a

specific condition

*221 + X + #

X = 1; Answer condition X = 2; Busy condition X = 3; Do Not Disturb condition

If you select Call Progress tone supervision, the unit detects a busy tone based on the cadence parameters set using code *371. It detects an answer when voice is recognized. The unit does not check for Ring-Back tone cadences.

The unit distinguishes between two types of transfers:

 Transfer to operator  Transfer to the rest of the extensions.

Table 4-9 explains how to program supervised, semi-supervised and nonsupervised transfers to the operator and to the rest of the extensions.

Table 4-9: Transfer Modes Programming Commands

Operation Command

Transfer mode for all extensions

*350 + X + Y where X = 1; All extensions except the operator X = 2; Operator extension only Y = 0; Non-Supervised (Default) Y = 1; Supervised Y = 2; Semi-Supervised

4.4.9.1 Detecting a Busy Extension

If the unit detects a busy extension, it performs a Recall-from-Busy and by default plays system message 96 (if the extension has a mailbox) or 103 (if the extension does not have a mailbox).

4.4.9.2 Detecting a No Answer from an Extension

If the unit does not detect an answer from the extension, it performs a Recallfrom-No-Answer and by default plays system message 97 (if the extension has a mailbox) or 104 (if it does not have a mailbox).

Voice Mail and Auto Attendant System Installation and Programming Manual 4-25

DTMF Programming

4.4.9.3 Changing the Busy and No Answer Menus

System messages 96, 97, 103, and 104 are default messages. The System Administrator can replace the system messages with script messages as follows:

 System message 96 (Busy and the extension has a mailbox) is replaced by

script message 21 in the first language, script message 31 in the second language and 41 in the third language.

 System message 103 (Busy and the extension does not have a mailbox) is

replaced by script message 22 in the first language, script message 32 in the second language and 42 in the third language.

 System message 97 (No-Answer and the extension has a mailbox) is replaced

by script message 23 in the first language, script message 33 in the second language and 43 in the third language.

 System message 104 (No-Answer and the extension does not have a mailbox)

is replaced by script message 24 in the first language, script message 34 in the second language and script message 44 in the third language.

4.4.9.4 Do Not Disturb

Using the user menu, a mailbox owner can activate the Do Not Disturb mode. When a caller dials a Do Not Disturb extension, the unit plays system message 121 and does not transfer the call to the extension. The System Administrator can replace this message with script message 25 in the first language, script message 35 in the second language and script message 45 in the third language.

4.5 Additional Features

4.5.1 Changing Passwords

The unit uses three types of passwords:

 System Administrator’s password  Operator’s password  Mailbox owner’s password.

A password always contains digits (0-9). The default for all three types of passwords is 1234.

4.5.1.1 Changing the System Administrator’s Password

The System Administrator can change his password by dialing code *900 to enter the programming mode, dialing the current password and then dialing:

*600 + * + Old Password + * + New Password + #

The system administrator password must be between 4 and 8 digits long.

NOTE



Voice Mail and Auto Attendant System Installation and Programming Manual 4-26

Do not use spaces, letters, * and # keys.

The System Administrator’s password cannot be disabled.

DTMF Programming

4.5.1.2 Changing the Operator’s Password

The System Administrator can change the operator’s password by dialing code *900 to enter the programming mode, dialing the System Administrator’s password and then dialing:

*601 + * + Old Password + New Password + #

Operator’s password must be 4 digits long.

NOTE



Do not use spaces, letters, * and # keys.

To disable the operator’s password, enter “0000”.

4.5.1.3 Resetting the Mailbox Password

The System Administrator can reset a mailbox password to its default (1234) by dialing code *900 to enter the programming mode, dialing the System Administrator’s password and then dialing:

*570 + XXXX + #

Where: XXXX is the mailbox number. The mailbox owner can change the mailbox password.

4.5.2 Activate Flash Memory Force Reorganize

The Flash memory reorganize option automatically reorganizes and optimizes the data stored in the unit.

The system administrator can activate the Flash memory Force Reorganize option by calling the unit and, during the opening greeting, dialing:

*900 + Password + *610

NOTE



This option cannot be deactivated, and should be activated by a certified technician only.

4.5.3 Changing to/from Day Light Saving Time

The operator can change to/from Day Light Saving time by calling the unit and, during the opening greeting, dialing:

*7 + XXXX + Y

XXXX = the operator’s password. This password can be disabled. Y = 0; reduces the time by one hour Y = 1; increases the time by one hour.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-27

DTMF Programming

4.5.4 Changing the Operational Mode

The operator can change the operational mode by calling the unit and, during the opening greeting, dialing:

*8 + XXXX + Y

XXXX refers to the operator’s password. This password can be disabled. Y = 0; Day Mode Y = 1; Night Mode Y = 2; Holiday Mode Y = 3; Auto Mode Y = 4; Break Mode

4.5.5 Playing a System Message

To listen to any system message, dial *900 and the administrator password to enter the programming mode, then dial:

*690 + Z + XXX

Z = the language number Z = 1 is the first language Z = 2 is the second language Z = 3 is the third language XXX is the message number See Chapter 12 for a list of system messages.

4.5.6 Playing All System Messages

To listen to all system messages, dial *900 and the administrator password to enter the programming mode, then dial:

*691 + Z

Z = the language number Z = 1 is the first language Z = 2 is the second language Z = 3 is the third language See Chapter 12 for a list of system messages.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-28

DTMF Programming

4.5.7 System Message Setting

To determine if some of the system messages are played, dial *900 and the administrator password to enter the programming mode, then dial:

*699 + X + Y

Where: X = system message affected: X = 1 system message 004 X = 2 system message 102 X = 3 system message 095 Y = 0 play the message (default) Y = 1 do not play the message Y = 2 (only when X = 3) plays message to mailboxes without a greeting message

4.5.8 Listening to the Software Version Number

To hear the unit’s software version number, dial *900 and the administrator password to enter the programming mode, then dial:

*680

4.5.9 Resetting the System

The System Administrator can reset the unit to its factory default settings by dialing *900 and the administrator password to enter the programming mode, then dial:

654 + * + XXXX + #

Where: XXXX = the System Administrator’s password.

NOTE



If you plan to reconfigure the unit for use with your current PBX and the unit had previously been configured for use with a different PBX type, use this command to clear all existing settings and return to the factory default settings.

4.5.10 Adjusting Recording Length

The System Administrator can select the length of the recorded messages in the unit. The selected length of message (in minutes) will affect all recorded messages. The types of recorded messages that are affected are: script recordings, mailbox owner’s greetings, name recordings and recorded incoming calls.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-29

DTMF Programming

To set message length dial *900 and the administrator password to enter the programming mode, then dial:

*790 + X

X = 1-9 minutes. This parameter is set to two minutes by default.

Voice Mail and Auto Attendant System Installation and Programming Manual 4-30

Switching to Computer Programming

Chapter 5: Switching to Computer

Programming

5.1. General

This section describes the purpose and main features of the Voice Mail Maintenance Software (VMS) and details the installation process. The VMS enables you to:

• Define PBX parameters

• Set the unit clock and calendar

• Create and maintain mailboxes

• Build Automated Attendant menus

• Review traffic statistics

• Print system parameters and statistics.

Programming the unit via the PC is done offline until sent in one block to the unit. We recommend that you save the new configuration in a file.

Using the VMS, you can also:

• Open a configuration file to make changes and then to upload them to the unit

• Recognize connected unit

• Open the corresponding default configuration file

• View unit statistics, e.g. line and memory utilization.

5.2. Connecting the Unit to the Computer

 To enter the programming mode:

1. Remove the side panel cover of the unit.

2. Remove all cables attached to the unit’s RS-232 connector.

3. Connect one end of the RS-232 cable to an available serial port on your PC and the other end to the unit’s RS-232 connector as shown in Figure 5-1.

Voice Mail and Auto Attendant System Installation and Programming Manual 5-1

Switching to Computer Programming

Figure 5-1: RS-232 Cable Connection

5.3. System Requirements

Before installing the VMS, check that your computer meets the following minimum requirements:

• PC Pentium II or higher

• Set the unit clock and calendar

• Create and maintain mailboxes

• 64 MB RAM memory

• 40 MB free hard disk space

• Microsoft Windows 95, Windows 98,Windows NT SP64, Windows 2000 Pro

and Windows XP

• Internet Explorer 5.5 or higher

5.4. Installing the VMS

 To install the VMS:

1. Exit all open applications.

2. Insert the CD with the VMS installation program into the CD drive.

3. Use Windows Explorer to locate the setup file.

4. Double-click the setup file.

5. Follow the instructions on the screen.

Voice Mail and Auto Attendant System Installation and Programming Manual 5-2

Switching to Computer Programming

5.5. Starting VMS

To start the VMS click on the VMS icon. The application will offer to select relevant Com port for read configuration data from the device.

Figure 5-2: COM Port Selection Window

Select a COM port and press OK.

NOTE



To continue to work in Off line mode press Cancel.

Applications will start to download configuration data. During transfer process the target device will be recognized automatically. The device’s name will be shown on the Main screen.

For to continue to work in offline mode application will offer to select the device, for which configuration file will be created.

Figure 5-3: Product Type Window

Voice Mail and Auto Attendant System Installation and Programming Manual 5-3

Switching to Computer Programming

Figure 5-4: Main Screen

NOTE



To continue to work in Off line mode press Cancel.

5.5.1. Communication Setup

The communication between the PC and unit needs to be checked initially. By default, COM Port 1 is used to send data to and receive data from the unit. To change this setting:

1. Select CommunicationComPort. COM PORT Selection window opens

(Figure 5-2).

2. Select the relevant COM Port and click OK. You can now use the VMS to

program the unit.

Figure 5-5: Communication Menu

Voice Mail and Auto Attendant System Installation and Programming Manual 5-4

VMS Programming

Chapter 6: VMS Programming

6.1. General

This chapter describes all menu item. In some cases, the DTMF commands are added as an extra reference and examples are clarified.

6.2. File Menu

Via the File menu you can execute the functions Open, Save, Save As, Open Default, Print Settings Menu, Print, Print Preview, Print Setup, Options and Exit.

Figure 6-1: File Menu

6.2.1. Open

The Open function from the File menu opens the Product Type window (Figure 6-2), where you can define the target device and then standard Windows Open screen (Figure 6-3), via which you can open an existing configuration file.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-1

VMS Programming

Figure 6-2: Product Type Window

6.2.2. Save

The Save function from the File menu saves the current open and previously saved file over the existing file on the hard disk. In case the file has not been saved previously, the Save As screen will appear.

6.2.3. Save As

The Save As function from the File menu saves the current open file with the specified name in the specified directory. You can save files with the following extensions:

*.VUP corresponding to VM-128 (VME-4000)

Figure 6-3: Open Window

Voice Mail and Auto Attendant System Installation and Programming Manual 6-2

VMS Programming

Figure 6-4: Save As Window

6.2.4. Open Default

The Open Default function in the File menu opens the default device’s file. You must first specify the target device.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-3

VMS Programming

6.2.5. Print Settings Menu

The Print Settings menu function in the File menu (Figure 6-5) opens a submenu in which you can define the parameters for printing.

6.2.6. Print

The Print function in the File menu opens the default Windows Print window.

Figure 6-5: Print Settings Menu

Figure 6-6: Print Window

6.2.7. Print Preview

The Print Preview function in the File menu (Figure 6-7) shows a default Windows preview of the parameters that need to be printed.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-4

VMS Programming

Figure 6-7: Print Preview Window

6.2.8. Print Setup

The Print Setup function in the File menu (Figure 6-8) opens a default Windows Print Setup window.

Figure 6-8: Print Setup Window

6.2.9. Options

The Options function in the File menu consists of two screens: The Toolbar Configuration screen and the File Location screen.

6.2.9.1. Toolbar Configuration

In the Toolbar Configuration screen (Figure 6-9) you can select the toolbars and tooltips that will be displayed.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-5

VMS Programming

Figure 6-9: Options Window – Toolbar Configuration Tab

6.2.9.2. File Location

In the File Location screen (Figure 6-10) you can define the save and load location of the files. By default, the location is the same as where the VMS.EXE program is stored.

Figure 6-10: Options Window – File Location Tab

6.2.10. Exit

The Exit function in the File menu closes the VMS program. If you have made changes to the parameters and not saved the file, the program will ask if you want to save the configuration file before exiting the program.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-6

VMS Programming

6.3. Communication Menu

Via the Communications menu you can execute the functions Read Parameters, Send Parameters, Read Recording, Send Recording, Backup, Restore, System Init, Password and ComPort.

Figure 6-11: Communication Menu

6.3.1. Read Parameters

The Read Parameters function in the Communications menu reads the information from the Voice Mail to PC. You can edit this information.

Figure 6-12: Read Parameters Window

NOTE



When reading parameters from the unit, the system will not answer any calls.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-7

VMS Programming

6.3.2. Send Parameters

The Send Parameters function in the Communications menu sends the edited information from the PC into the unit (Figure 6-13). After clicking OK, a screen asking for the administrator password appears.

Figure 6-13: Send Parameters Window



Figure 6-14: Password Window

NOTE

Before editing and sending parameters in the VMS, FIRST perform a read action, otherwise you may overwrite the existing information with default information or other incorrect information.

When sending parameters to the unit, the system will not answer any calls.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-8

VMS Programming

6.3.3. Read Recording

The Read Recording function in the Communications menu reads the script recordings from the unit to the VMS. You can edit this information or send it to another unit.

Figure 6-15: Read Recording Window

NOTE



The script recordings in the unit are not .WAV files, but special DSP formatted files. WAV files cannot be converted to this format.

To copy a script from one unit to another, the scripts need to be recorded via telephone for the first unit. The scripts can then be transferred via the Read/Send Recording functions to another unit.

6.3.3.1. List of Script Recordings to be Read

The List of Script Recordings button shows a screen in which scripts can be selected. After selecting Script Recording numbers from the list (Figure 6-16) and pressing the Add button, you need to define the location where to store them (they will be stored with the extension of the Script Recording number e.g. script.10, script.00). The delete button is used to unselect the chosen script(s).

Voice Mail and Auto Attendant System Installation and Programming Manual 6-9

VMS Programming

Figure 6-16: List of Scripts to be Read Window

6.3.4. Send Recording

Figure 6-17: Send Recording Window

The Send Recording function in the Communications menu sends the script recordings from the VMS into the unit.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-10

VMS Programming

6.3.4.1. List of Script Recordings to be Sent

The List of Script Recordings button shows a screen in which scripts can be selected. After selecting Script Recording numbers from the list and pressing the Add button, you need to select the files from the location where they were stored (They will have the extension of the Script Recording number e.g. script.10, script.00, see Figure 6-18). The delete button is used to unselect the chosen script(s).

When a Script Recording needs to be replaced by another Script Recording number (e.g. Script 10 needs to replace the script linked to Script Recording number 4), perform the following steps:

1. Select the Script Recording number to be updated.

2. Click Add.

3. Change the File of Type to All Files.

4. Select the Script Recording that must be used.

5. Click OK. The script had been replaced.

Figure 6-18: List of Scripts to be Sent Window

Voice Mail and Auto Attendant System Installation and Programming Manual 6-11

VMS Programming

6.3.5. Backup

The Backup function in the Communications menu enables a full backup of the unit, containing all scripts, messages, personal greetings and parameters. The information is collected in a WAX file.

Figure 6-19: Backup Window

6.3.6. Restore

The Restore function in the Communications menu enables a full restore of the unit. The WAX file contains all scripts, messages, personal greetings and parameters.

NOTE



You can use a WAX file to transfer the identical contents from one unit to another.

Figure 6-20: Restore Window

Voice Mail and Auto Attendant System Installation and Programming Manual 6-12

VMS Programming

6.3.7. System Init

The System Init function in the Communications menu is used to reset or update the unit and to clear the flash memory. The VOX file contains all system messages and language combinations. After a System Init, the unit will return to the manufacturers defaults.

Figure 6-21: System Init Window

6.3.8. Password

The Password function in the Communications menu provides the possibility to change the administrator’s password. The password may be 4 to 8 digits long only. The default is 1234.

Figure 6-22: Change Password Window

Voice Mail and Auto Attendant System Installation and Programming Manual 6-13

VMS Programming

6.3.9. ComPort

The ComPort function in the Communications menu enables you to change the communication port number, used to enable the communication between the PC and the unit.

Figure 6-23: COM Port Selection Window

6.4. Parameters Menu

Via the Parameters menu you can execute and configure the functions PBX Parameters, System Parameters and In-Band DTMF Protocol.

Figure 6-24: COM Port Selection Window

6.4.1. PBX Parameters

The PBX Parameters function in the Parameters menu consists of a number of tabs, which will be detailed separately.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-14

VMS Programming

6.4.1.1. Extensions

Figure 6-25: PBX Parameters Window – Extensions Tab

Extension’s Size – The PBX extension size needs to be defined. This refers to the numbering plan of the PBX, for example: if the extensions in the PBX are from 200 to 299, then the extension size is 3 digits. Please note that 2, 3 or 4 can be used and the default is 3.

Command: *300 Fax Extension – The fax extension number is entered in this box. The Voice Mail will

detect the fax tone, (1100 Hz), and immediately transfer the call to this extension. In order to disable this feature, leave the box empty.

Command: *360 Operator ID – The digit defined here will route calls to an operator’s extension during the

auto attendant scripts menus and from users mailboxes. Depending on the operation mode the call will be transferred to either the day or night operator extension.

Command: *330



NOTE

Make sure that the day and night operator extensions are configured.

Day Operator Extension – The extension number defined here is the number that will be used whenever the operator ID digit is accessed while the Voice Mail is in Day Mode.

Command: *360

Voice Mail and Auto Attendant System Installation and Programming Manual 6-15

VMS Programming

NOTE



Night Operator Extension – The extension number defined here is the number that will be used when the operator ID is accessed while the Voice Mail is in Night, Break or Holiday

Mode.

Make sure that the day and night operator extensions are configured.

Command: *360

PBX Legal Extensions – This is the range of extension numbering from the PBX. Here extensions are filtered for the Direct Calling from the Auto Attendant. If there are a certain designated extensions that do not want theDirect Call function that extension is left out in the groups of extensions.

For example: Group 0 has the extensions 200 – 203 and Group 1 has the extensions 205 – 299 this means that extension 204 cannot be directly contacted from the Auto-Attendant scripts and if that extension is tried from any script, then the Voice Mail will say, “Invalid entry, please try again”.

Command: *320



NOTE

The legal entries are any numbers up to 4 digits and the default is 0.

6.4.1.2. Call Transfer

Figure 6-26: PBX Parameters Window – Call Transfer Tab

Voice Mail and Auto Attendant System Installation and Programming Manual 6-16

VMS Programming

Transfer Code - This code is used to transfer a call from an analog extension to another. & = Represents a Hook Flash X = Represents an Extension number DTMF = O- 9, A-D P = Pause 1sec

Command: *380 Recall from Busy Code – This code is only applicable for semi or supervised modes and it

defines the PBX code that is used in order to return the caller to the Voice Mail when the desired party is busy.

Command: *380 Recall from No-Answer Code – This code is only applicable for supervised mode and it is

used to return the caller to the Voice Mail when the caller has been transferred to an extension that is not answered.

Command: *380 Hook Flash Time (&) – Here the Hook Flash time of the PBX is defined. Command: *370 Hook Flash Time 2 (@) – This is not a programmable parameter and its only used in cases

where disconnect (@) is added to the code.

6.4.1.3. Supervision

Figure 6-27: PBX Parameters Window – Supervision Tab

Voice Mail and Auto Attendant System Installation and Programming Manual 6-17

VMS Programming

Transfer Mode – By selecting a radio-button you can define the operation mode for the Voice Mail’s Auto Attendant. Non-Supervised is when the Voice Mail transfers the call without checking the status of the target extension, Semi-Supervised is when the Voice Mail only recognizes the busy signal from the PBX and Supervised is when the Voice Mail check for busy signal from the PBX and no-answer time out.

Command: *350 Call Progress Tones – In this drop-down menu, the method used to detect answered, busy

and DND (Do Not Disturb) status when a call is being transferred to an extension in semi or supervised mode. The two options are either Call Progress Tones or DTMF. For Call Progress Tones, the Voice Mail samples the sounds from the PBX, such as busy or disconnect tones, and in the case of DTMF, the Voice Mail waits to receive DTMF signals from the PBX for busy, no answer and DND.

Command: *220 DTMF Codes from PBX – The answer, busy and DND signals are only programmable

when changing the default from CPT to DTMF. Answer Signal – is the DTMF signal sent from the PBX to the Voice Mail when a call is

answered in supervised mode. (off hook signal) Busy Signal – is the DTMF signal sent from the PBX to the Voice Mail when a call is

transferred to a busy extension while in supervised mode. DND Signal – is the DTMF signal sent from the PBX to the Voice Mail when a call is

transferred to an extension in Do Not Disturb mode in supervised mode. Command: *221 Time to Wait for No Answer – In this selection box, the time for the Voice Mail to wait

for answer after transferred a call in supervised mode .the default is 20 seconds. Command: *311 Voice Sensitivity – In this selection box, the sensitivity to human voice is defined, only for

supervised mode. Command: *376

Voice Mail and Auto Attendant System Installation and Programming Manual 6-18

VMS Programming

6.4.1.4. CP Tone & Disconnect

Figure 6-28: PBX Parameters Window – CP Tone & Disconnect Tab

Busy Tone – The “Busy on-time” and the “Busy off-time” determine the busy tone cadence. Busy tone is used for: a.) Detecting a busy extension when transferring a call in semi or supervised transfer mode and b.) Disconnecting the line when detecting a disconnect situation.

Command: *371 Disconnect Code – This defines the DTMF code sent from the PBX to the Voice Mail that

instructs the Voice Mail to disconnect the line. Command: *333

Disconnect Tone – The disconnect on-time and off-time define the disconnect tone cadence. The disconnect tone usually appears when the caller hangs up. The Voice Mail will disconnect the line upon detecting this tone.

Command: *371



NOTE

This code is sent only to VM extensions.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-19

VMS Programming

6.4.2. System Parameters

Figure 6-29: System Parameters Window

The System Parameters function in the Parameters menu defines a number of essential system related parameters.

Max. Recording Time – In this box the maximum recording time for the user messages, script messages, mailbox greetings and names are determined.

Command: *790

NOTE



Default System Language – The Voice Mail supports 3 languages simultaneously. Here is where system administrator determines which language, out of the 3 inserted in the Voice Mail, will be the default language for the system messages.

Command: *118 Auto Gain Control – When enabled, this adjusts the line volume so incoming calls will be

recorded at the same level (messages, script messages & mailbox greetings). Command: *377

Changing this parameter will affect on the operation mode of the Voice Mail.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-20

VMS Programming

Directory Listing – This is the “Dial By Name” feature for the caller in order to locate a mailbox owner from the Auto Attendant using first names or last names can do this.

Command: *011

6.4.3. In-Band DTMF Protocol

Figure 6-30: In-Band DTMF Protocol Window

The In-Band DTMF Protocol function in the Parameters menu provides four screens in which the PBX integration codes are defined.

Code Received from PBX – In this column we define the DTMF string that is sent from the PBX to the Voice Mail, (only if the PBX is In-Band DTMF protocol supported and Voice Mail extension is defined as a VM extension). There is an option to have up to 40 strings and for each string the operation should be defined.

Command: *200,201,202 Max. Time to Wait for DTMF – The maximum amount of time the Voice Mail must wait

until is receives its first DTMF from the PBX. Command: *210 Max. Delay Between DTMFs – The maximum amount of time is defined between each

DTMF in the string sent by the PBX to the Voice Mail. Command: *211

Voice Mail and Auto Attendant System Installation and Programming Manual 6-21

VMS Programming

NOTE



If a DTMF is not heard within the allocated time, the opening greeting will be heard.

6.5. Auto-Attendant Menu

Figure 6-31: Auto-Attendant Menu

Via the Auto-Attendant menu, you can configure the Script Menus and Scheduling table.

6.5.1. Script Menu

The Script Menu function in the Auto-Attendant menu consists of a number of screens, which will be shown separately. A number of screens contain example information.

6.5.1.1. Script Programming

Figure 6-32: Script Menu Window – Script Programming Tab

In this screen you can define the operation for each DTMF and a view wide array of choices.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-22

VMS Programming

Script Number – In the box you define the Script number, which has to be edited.

EOM = End of Message – this is operation what will be done at the end of the message.

EOM Time Out – this is the amount of time before EOM operation will be done. Type of Operation – The Type of Operation provides a drop-down menu, from

which a number of options can be chosen. The choices are:

Transfer to a script message – This will transfer the caller to the sub-menu, which is defined in the destination.

Command: *110 Transfer to a Script Message + 1st Language, 2nd Language or 3rd Language – This is an

option to transfer to the sub menu defined in the destination and to change the language until the end of the session.

Command: *117 Max. Delay Between DTMFs – The maximum amount of time is defined between each

DTMF in the string sent by the PBX to the Voice Mail. Command: *211 Directory List – This is the ”Dial by name” feature. After pressing the DTMF for this

option the Voice Mail will ask the caller to enter the 1 the required party. Each mailbox in the list has to define Directory list code and record the Name.

Command: *111

3 letters of the first or last name of

Transfer to an Extension – When pressing the relevant DTMF for this option the call will be transferred to the number defined in the destination.

Command: *120

NOTE



Voice Mail and Auto Attendant System Installation and Programming Manual 6-23

The number can be up to fur digits without any connection to the legal extension.

VMS Programming

Transfer to a Mailbox – This is the option for the caller to dial the required mailbox by pressing the digit and the call will then be directly transferred to the mailbox and the personal greeting played.

Command: *130 Direct Call to an Extension – The Voice Mail allows the caller to dial the required

extension independently. The extension number must be defined as a legal extension in the PBX Parameters

Command: *170 Direct Call to a Mailbox – The Voice Mail allows the caller to dial the required mailbox

independently. Command: *175 Leave a Message – The option here is to leave a message in a specific mailbox from the

Auto Attendant. After pressing on the relevant DTMF, the Voice Mail will ask for the mailbox number.

Command: *150 Retrieve Messages – This is the DTMF key for the retrieving message process. After

dialing this DTMF the Voice Mail will request the required mail box number and password and thereafter the “retrieve message” process begins.

Command: *160 Disconnect – Simply disconnects without any announcement. Command: *140 Disconnect with Message – This is what’s known as a “polite” disconnect, the Voice Mail

says “thank-you and good-bye” before disconnecting. Command: *140 Dial-a-String – In this case you need to enter the “String” number from the “Dial-a-String”

table. This is a “Free DTMF string dialing” call in a blind transfer to perform special PBX

applications (See the next table). The example screen in Figure 6-32 shows that we added the reactions to the DTMF

numbers 1, 2, 3, 4, 9 and EOM. For the numbers 2, 3 and 4 we also added the destination. Dial a string feature required to use Hook flash code for to transfer a call.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-24

VMS Programming

6.5.1.2. Dial-a-String

Figure 6-33: Script Menu Window – Dial a String Tab

In this screen you have to make definitions for the 20 DTMF strings to dial. A string can be up to 20 digit including A-D, 0-9, *, #, p for pause and & for Hook Flash.

In the example in Figure 6-33 the string starts with a hook flash (pick up the phone), a pause and than either a number for an outside line (with pause) and number or the number directly.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-25

VMS Programming

6.5.1.3. Script Opening

Figure 6-34: Script Menu Window – Script Opening Tab

In this screen the script opening parameters are defined. Line 1 and Line 2 are relevant for VM-48.

Number of Rings before Answer – The number of rings are defined before a call is answered on the respected line.

Command: *310 The Table – Defines which script to be played for each port (Script By Port). Here you can separate two companies on one Voice Mail and define the opening greeting

for each port. For each port there are four opening scripts defined according to the day, night, break and holiday modes.

Command: *112

Voice Mail and Auto Attendant System Installation and Programming Manual 6-26

VMS Programming

6.5.1.4. Script Recording

Figure 6-35: Script Menu Window – Script Recording Tab

In this screen you can define the Script Recordings (loaded and deleted).

6.5.1.5. Script Status

Figure 6-36: Script Menu Window – Script Status Tab

Voice Mail and Auto Attendant System Installation and Programming Manual 6-27

VMS Programming

In this screen displays a list of all the scripts with their programming and recording status. For each script you can name the file for future reference. The icon of the script will change if the script is recorded. A number of scripts have been pre-defined. In the example we have added the Script for Support and Marketing.

6.5.2. Time, Date and Weekly Schedules

Figure 6-37: Time & Date Window

The time and date function in the Auto-Attendant menu provides the options to change the time, date and operation mode.

System Time and Date – current date and time, by default the Voice Mail takes the time and date from your PC. The system time will be shown after the Read parameters from the system, otherwise PC time will be shown here.

Command: *420,*430 Mode of Operation – Defines the unit’s mode of operation. The mode can be changed by

DTMF code. In Auto mode, the Voice Mail will automatically change from day to night to holiday and to

break mode as programmed in the weekly schedule. Command: *8, *400

Voice Mail and Auto Attendant System Installation and Programming Manual 6-28

VMS Programming

6.5.2.1. Schedules

Figure 6-38: Time & Date Window

The schedules button on the time and date screen is available in the Auto Operation mode only.

NOTE



Automatic Mode – When the Voice Mail is programmed in Automatic mode, the weekly and holiday schedules must be programmed. Should you not do so, the Voice Mail will automatically play the opening greeting that was pre-programmed by the system clock. If a correspond script greeting is not recorded, system will be switched to the Manual Day mode automatically.

The Schedules screen contains two windows: Weekly Schedule and Holiday Schedules.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-29

VMS Programming

Weekly Schedule

Figure 6-39: Auto Window – Weekly Schedule Tab

Voice Mail and Auto Attendant System Installation and Programming Manual 6-30

VMS Programming

Figure 6-40: Auto Window – Auto Breaks Tab

Weekly Schedule – In above example the Weekly Schedule has been programmed as: on Monday from 8:00 to 14:00 the Voice Mail will play script message 00 (default day) and then from 14:00 to 15:00 script no 15 (default break), from 15:00 to 18:00 script 00, which is the day script again and then from 18:00 to 08:00 script 10 (default night).

Command: *450, *460

Voice Mail and Auto Attendant System Installation and Programming Manual 6-31

VMS Programming

Holiday Schedules

Figure 6-41: Auto Window – Holiday Schedules Tab

Holiday’s Schedule – This list (up to 50) shows the dates that are defined as holidays. If the holiday lasts more than 1 day, each of the holiday days must be inserted separately.

Command: *470

NOTE



Pressing the add button adds a new holiday and pressing the remove button deletes the selected days.

The default is empty.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-32

VMS Programming

6.6. Voice Mail Menu

Figure 6-42: Voice Mail Menu

Via the Voice Mail menu you can configure the List of Mailboxes, Notification Parameters and Groups of Mailboxes.

6.6.1. List of Mailboxes

The List of Mailboxes function in the Voice Mail menu consists of two screens, in which you can define the individual and general mailbox parameters.

6.6.1.1. List

Figure 6-43: List of Mailboxes Window – List Tab

The above list displays all the mailboxes defined in the Voice Mail and their configuration parameter values. You can add, edit, copy and delete values by clicking on the appropriate button in this screen. The description of the values is found in the following screen.

Supervisor Mailbox –define here the supervisor mailbox, which is used when the Voice Mail’s memory is 85% full. This mailbox will get the alarm messages about memory usage.

Command: *360

Voice Mail and Auto Attendant System Installation and Programming Manual 6-33

VMS Programming

Pressing the Add button (Command: *501)

Figure 6-44: New Mailbox Window – Mailbox Parameters Tab

Mailbox – Enter the mailbox number that you want to open. User Password – 1234 is the default. When the password has been changed to a “secret

Password” will be shown ****. If will need to change the password back to the default password, this is where it is done.

Mailbox Type – There are two types of mailboxes: real and virtual. Real Mailbox – This is a mailbox where there is an extension and a telephone. Virtual Mailbox – This is a mailbox without an extension. It has all the same functions as a

real mailbox, such as password protected. Command: *501 or *521 Announcer – Enables the Voice Mail to play a personal greeting (announcement), but does

not allow messages to be recorded. Command: *502 User Language – Select the language to be heard on your mailbox menu by selecting one

language from the three languages that have been chosen for the Voice Mail. Command: *533

Voice Mail and Auto Attendant System Installation and Programming Manual 6-34

VMS Programming

NOTE



Do Not Disturb – When this is enabled, the Voice Mail will not transfer any calls from the Auto-Attendant to this extension. The Do Not Disturb menu will be played instead.

Time Stamp – This is the option for the Voice Mail to play or not to play the time and date of the message.

Command: *531 Local Notification – Notification can be performed as local or external. The possible types

of local notification are as follows: Message Light 1 – The Voice Mail sends the code that is defined in Notification codes to

turn on the light on the telephone or to change the dial tone of the extension. Message Light 2 – This is the same as message light 1. This option is used with certain

PBXs that support more than 1 type of terminal. Sign Ring – The unit rings the extension number periodically as defined by the “ring

notification interval”, until all new messages have been heard or the maximum number of notification retries is reached.

After transferring a call in non-supervised mode using in band DTMF integration, the Busy, No Answer and Do not Disturb menu is played with the language defined here.

Rings – The Voice Mail rings the extension number for a period of time, as defined in the “ring notification duration” and the “ring notification retries”. After the call is answered the unit prompts a menu that allows the user to retrieve messages.

Command: *700 External Notification – The system administrator allows remote telephone and pager

notifications for each mailbox. Using the menu the owner can enable the remote notification status and enter a desired external telephone or pager number. If remote notification is allowed and enabled and a message is recorded, the Voice Mail dials the remote telephone number to notify the mailbox owner of new messages. After the mailbox owner enters the correct password, the unit plays the recorded message. When a remote pager is used the Voice Mail dials the number to notify the mailbox owner to call back and to check his/her mailbox. (No recorded message is played)

The Voice Mail stops sending ring notification after the mailbox owner has retrieved all messages or the defined number of notification retries has been exceeded.

Command: *710, *711

Voice Mail and Auto Attendant System Installation and Programming Manual 6-35

VMS Programming

6.6.1.2. Parameters

Figure 6-45: List of Mailboxes Window – Parameters Tab

Key to Retrieve Messages during Mailbox Greeting – This is the key that will be pressed during a personal greeting to enter to the mailbox menu for retrieve messages, i.e. if you want to retrieve a message from your mobile, dial your extension and when your personal greeting is played, press the defined key and the Voice Mail will then ask for password before playing the messages.

Maximum Number of Days to Store Messages – This parameter defines the number of days that messages are stored in a mailbox. After reaching the defined message limit, the messages are automatically deleted.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-36

VMS Programming

6.6.2. Notification Parameters

Figure 6-46: Notification Parameters Window

The Notification Parameters function in the Voice Mail menu contains a number of editable notification parameter.

Message Light 1-Code, Message Light 2-Code and Message Light Off-Code – The Voice Mail will dial the above codes always from port 2 and the legal entries are:

X = extension P = pause Q= 4 second pause (For External notification only!) & = hook flash ! = send number of new messages to LCD station (only if the PBX support it) DTMF = 0-9 , *,#,A-D

Message Light Off – The signal is used to turn off the message notification on the terminal. Some PBXs do not support this code so they turn off the notification LED after the Voice Mail is called.

Ring Notification Interval – This parameter defines how often the mail owner is notified of new messages by ring notification.

Ring Notification Retries – This parameter defines how many times the Voice Mail will try and notify the user of received messages.

External Notification Start/Stop – Sets the time for external notification.

Voice Mail and Auto Attendant System Installation and Programming Manual 6-37

VMS Programming

PBX External Line Access Code – This is the key pressed by the Voice Mail to get an external line for external notification. External access code can be 1-4 digits.

Message Light Activation – Defines if lights up for every message or only after the first new message.

Ring Notification Duration – The amount of time the Voice Mail opens a line and tries to notify the caller of new messages in the ring notification process.

In the above example *68 is the message light code for a specific PBX. P is pause and the X stands for a specific extension.

6.6.3. Groups of Mailboxes

Figure 6-47: Notification Parameters Window

The Groups of Mailboxes function in the Voice Mail menu consists of a number of columns, in which groups can be created. The example screen above contains a number of groups.

Group List – Up to four mailboxes can be defined. The mailboxes that are defined within a group can be addressed simultaneously by dialing the group number. In order to add a mailbox to a group, select the required mailbox from the group of all mailboxes ending with the digits 099 and press on the “Add” button of the respective group. The group 099 is a list of all the mailboxes defined in the system.

NOTE



Voice Mail and Auto Attendant System Installation and Programming Manual 6-38

Each group can contain up to 20 mailboxes (excluding the group for all mailboxes).

VMS Programming

First Digit of Groups – This parameter defines the digit that the mailbox groups start with. If a mailbox and a group of mailboxes have been defined with the same number, the messages will be sent to a mailbox and not to the group.

6.7. Line Monitor Menu

Figure 6-48: Notification Parameters Window

Via the Line Monitor menu you can activate the Line Monitor tool. The tool shows online all incoming DTMF signals, simultaneously from all ports via the RS-232 cable.

6.7.1. Activate the Line Monitor

 To activate the line monitor:

1. Connect the RS- 232 cable, one end to the PC and the other end to the Voice Mail.

2. Open the Line Monitor window (Figure

6-49).

3. Click the start button. All DTMF signals are displayed online.

Figure 6-49: Line Monitor Window

Voice Mail and Auto Attendant System Installation and Programming Manual 6-39

VMS Programming

6.8. Statistics Menu

Figure 6-50: Statistics Menu

The Statistics menu provides the general statistics related to the unit and a List of Messages and Statistics per mailbox.

6.8.1. General

NOTE



Each group can contain up to 20 mailboxes (excluding the group for all mailboxes).

To receive the most accurate information, perform CommunicationRead Parameters before opening the General Statistics.

Figure 6-51: List of Messages Window

After reading the parameters, the above screen will contain the available list of mailboxes. When clicking on a specific mailbox, the following information will be displayed:

• All messages for that specific mailbox

• Date per message

• Time per message

• Length per message

• Status per message

• Total length of new messages

• Total length of saved messages

• Total number of new messages

• Total number of saved messages

Voice Mail and Auto Attendant System Installation and Programming Manual 6-40

Its telecom VME-4000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual