Istorage Diskashur PRO User Manual
PRO
®
User
Guide
Remember to save your PIN in a safe
place. If lost or forgotten, there is no way
to access the drive.
If you are having difculty please refer
to the complete user’s manual which is
loaded on your diskAshur PRO drive and
is also available at iStorage’s website:
www.istorage-uk.com/support
Table of Contents
About the diskAshur PRO 4
Package contents 4
diskAshur PRO - Connections 5
Before you begin 5
Connecting diskAshur PRO 5
Connecting with the USB Y-Cable 6
diskAshur PRO Keypad Panel 7
First Time Use 7
Locking the Drive 8
Unlocking the Drive 8
Admin Mode 8
Changing the Admin PIN 8
Adding a new User PIN 9
Deleting the User PINs 9
Changing the User PIN 9
Setting the Unattended Auto Lock Feature 10
diskAshur PRO Brute Force Protection 11
Setting a Self-Destruct PIN 12
Performing a Complete Re-Set 12
Initializing and formatting the diskAshur PRO after a reset 13
Hibernating or Logging off from the OS 14
diskAshur PRO Setup for Mac OS 15
Troubleshooting 16
Technical Support 18
Warranty and RMA information 18
Copyright © iStorage Limited, Inc 2013. All rights reserved.
Windows is a registered trademark of Microsoft Corporation.
All other trademarks and copyrights referred to are the property of their
respective owners.
Distribution of modied versions of this document is prohibited without
the explicit permission of the copyright holder.
Distribution of the work or derivative work in any standard (paper) book
form for commercial purposes is prohibited unless prior permission is
obtained from the copyright holder.
DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR
IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,
ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH
DISCLAIMERS ARE HELD TO BE LEGALLY INVALID
About the diskAshur PRO
TM
Looking for the highest level of
security for your data while utilizing
the fastest USB 3.0 speeds?
Look no further than the
diskAshur PRO 140-2 Validated
Drive, certied and tested to NIST
FIPS 140-2 Level 2 requirements
and with the fastest speeds of
iStorage’s Secure Drive line.
Sporting an easy-to-use keypad
design that is impervious to dust
and grit, with a software free setup
and operation, the diskAshur PRO
enables you to access the drive
simply and easily with your own
unique PIN. And with a super fast
integrated USB 3.0 cable, you can
access your data faster than ever
before.
Package contents
• diskAshur PRO drive with
integrated USB 3.0 cable
• Travel pouch
• USB Y-cable
• Quick Start Guide
diskAshur PRO
Quick Start Guide
SHIFT button
1
UNLOCK button
2
4
LOCK button
3
LED Indicator lights
4
3
When you rst plug in the
diskAshur PRO, the unit will do
a self-test to verify all security
2
components are working properly.
The LEDs will go through 3 test
stages RED, GREEN, and BLUE.
1
This will be followed by three
®
GREEN ashes on a successful
PRO
test. Any test failure will leave the
unit in an interoperable state with
First Time Use
Before the drive can be used, the Admin PIN MUST be set. The LED will display Solid
BLUE and Solid GREEN to indicate the diskAshur PRO is waiting for a PIN to be set.
To Set-up the Admin PIN:
1. Press UNLOCK + 9. The LED will change to Solid BLUE and Blinking GREEN.
2. Enter the new Admin PIN and press UNLOCK key. If accepted the GREEN LED
3. Re-enter the Admin PIN and press the UNLOCK key. If accepted the GREEN
4. LED will then turn BLUE and remain in Admin mode for 30 seconds or if the
5. The Admin PIN is now set and will allow access to the drive or the Admin features.
6. To UNLOCK the drive, exit Admin by pressing the LOCK button. Then enter the
the RED LED ashing.
will ash for 3 short blinks, then return to Solid BLUE and Blinking GREEN.
LED will be Solid for 3 seconds.
LOCK key is pressed, will return the drive to a standby state.
new PIN and press UNLOCK.
*Note: PINs must be a minimum length of 7 maximum 16 digits.
Cannot contain all consecutive numbers (2345678 or 9876543)
Cannot contain all same number (1111111)
The SHIFT key can be used for additional combinations.
SHIFT + 1 are a separate value than just 1.
4
diskAshur PRO - Connections
Before you begin
Be sure to review the following information before you begin to use
diskAshur PRO.
Attention: Use only the included cables with your diskAshur PRO.
You might damage the drive if you use a cable not included with the
diskAshur PRO.
diskAshur PRO is designed for portable use without an AC power adapter
and in most cases will be able to power on a single USB port. In the event
that diskAshur PRO is unable to power on a single USB connection, use
the included USB Y-cable. The diskAshur PRO is not self-powered and
requires connection to a USB port to perform all operations.
Connecting diskAshur PRO
1. Attach the integrated USB cable of the diskAshur PRO drive to an
available USB port on your computer, as shown below.
NOTE: While diskAshur PRO will work with any USB port, for the
fastest speeds connect to a USB 3.0 port on your computer.
2. At least one of the diskAshur PRO LEDs should turn on, indicating that
it is receiving power.
If none of the LEDs turn
on or the drive locks when
writing to the disk, use the
included USB Y-cable.
Refer to directions on the
following page
5
Connecting with the USB Y-Cable
If none of the diskAshur PRO LEDs power on a single USB connection,
use the included USB Y-cable.
1. Attach diskAshur PRO’s integrated USB cable to the female connector of
the USB Y-cable.
2. Connect the two male USB connectors to two available USB ports on
your computer.
3. At least one of the diskAshur PRO’s LEDs should turn on, indicating that
the diskAshur PRO is powered.
6
Loading...