Page 1
LP700Z
Instruction Manual
LP700Z is a kind of eight- eye blinder with 120V/650W bulb which can be
controlled by DMX512 controller to achieve dimmer function. The unit
include one channel, two channels and four channels for DMX signal
(CH01:8 bulbs/channel , CH02: 4bulbs/channel and CH04: 2 bulbs /
channel) and can work under Auto or DMX mode.
I Technical Specifications:
ITEM NO：LP700Z
Name：BRIGHT SHOOT LIGHT WITH DIMMER FUNCTION
Voltage：AC 230V/50Hz
Bulb： DWE 120V/max 650W(8X)
Fuse： 230V/6.3A(4X)
Net Weight: 11Kg
Size：L931*W454*H109.5 mm
第 1 页 共 1页
Page 2
II. Function and control board:
MODE ME NU
TOTAL DMX CHANNEL
RECEI VE
DMX CHA NNEL
CHASE PROGRAM
CHASE
CHASE SPEED
CHASE DI MMER
POWER
POWER I NPUT:
10
9
DI SPLAY
CH: 01 / CH: 02 / CH: 04
R001 R512
P:01 P:16
SP:01 SP:16
D000 D100
AC 120V- 60Hz, 20A Max
III . Working Button
1. Manual：Auto/DMX mode
2. up
1 CH 2 CH 4CH3 CH
DMX Si gnal
8
MODE
MENU
12 43
FUSES: F6. 3A 250V 5* 20mm
3 421
11
Receiv e
Chase
7
DMX IN DMX OUT
3
1=Ground
2=Dat a"- "
3=Dat a"+"
1 2 2 1
5 6
3
3. down
4. Power plug
5. DMX input
6. DMX output
7. LED indicator：indicator for the channel output
8. LED display：display working mode
9. Power cord
10. Power switch
11. Fuse: 230V/6.3A
IV. Operation Instruction:
1. Unpack the carton to check if there is any damaged or missing parts
when you receive the unit, call the local dealer if anything is found not
in a normal condition.
第 2 页 共 2页
Page 3
2. Open the lamp cover to install lamp. Keep the lamp untouched by
hand and disconnect the unit from power while Re-lamping.
3. Place the unit where there is efficient ventilation, away from any
flammable and explosive objects.
4. Check that the rated power corresponds to the main supply.
5. Disconnect from power supply and cool down the unit before
re-lamp and open the lid and then replace the burnt-out lamp.
V. Working mode：
This unit has two kinds of working mode: (1) Auto mode: four channel
chasing，(2) DMX mode: receiving DMX signal
Auto Mode (chasing)：this unit has 16 kinds of built-in program and
the speed and brightness of chasing can be adjusted by button. Turn on
the power switch.
1. Press “MODE”，display “P01” or “P16”
2. Press “UP” or “DOWN”，you can choose from “P01” to “P16”
3. Press “MENU”，display “SP01” or “SP99”
4. Press “UP” or “DOWN”，you can choose from “SP01” to “SP99”. If
“01” , the speed can reach 1chasing/30S，If “99”, the speed reach the
fastest level, 10 chasings/1S.
5. Press “MENU”， can display from “D00” to “ D100”
6. Press “UP” or “DOWN”，and then choose brightness. “99” is the
brightest level.
DMX Mode：Receiving one channel, two channels or four channels
第 3 页 共 3页
Page 4
DMX signal.
1. Connect DMX signal cable.
2. Turn on the power switch
3. Press “Mode”, display “A001” or “A512”
4. Press “UP” or “DOWN”，you can choose channel from “A001” to
“A512”. It will be the original DMX channel.
5. Press “MENN”，display “CH01” or “ CH04”
6. Press “UP” or “DOWN”，you can choose “CH01” to “CH04”
CH01: DMX controller only receive the selected value of DMX
channel. CH02: No.1 and No.2 channel of controller only receive selected
DMX value; No.3 and No.4 channel of controller only receive two serial
DMX value. CH04: four channels of controller can receive four serial
DMX value respectively.
7. DMX value : brightness. (“0” : close , “100”: brightest.)
VI. Caution：
1. Call professionals for maintenance, no spare parts are included with the
unit.
2. Give the unit a break after 15 minutes of continuous use.
3. Replace bulbs and protector with those of proper specifications.
4. The lamp shall be changed if it has become damaged or thermally
deformed.
5. Please be sure to mount luminaires only as shown on the picture below,
means hanging on the bracket; Additionally, you can use a stable base
for the fixing of the luminaires.
第 4 页 共 4页
Page 5
6. Please ask an approved electrician because of special national
Clamp eg. Steel " S" or "C"
requirements for Electrical installation. No operation without proof by
skilled electrician in public area!
7. No naked flame sources, such as lighted candle, should be placed on the
apparatus.
8. The use of apparatus should be in moderate climate.
9. The apparatus should not be exposed to dripping or splashing and that
no objects filled with liquids, such as vases, shall be placed on the
apparatus.
10.Alternative precautions to switch off the device shall be taken if it is not
easy to reach the socket or switch off the lamp tube (e.g. additional
disconnection device).
VII. Installation:
Steel wire 3mm equiral chain
Screw M8x20mm
第 5 页 共 5页
Page 6
第 6 页 共 6页
Loading...