Throughout this catalog you will notice letters to draw your attention to specific footnotes which are located at the
bottom of the page or below specified charts.
Parts Catalog Usage Guide
To order call toll free 1-800-333-6900, or www.invacare.com
The information contained in this document is subject to change without notice. This catalog contains
service parts for Form No. 04-041. If you have any questions regarding this catalog, please contact one
of our Customer Service Representatives.
For Customer Service Support Call:
1-800-333-6900
For Faxed In Orders Call:
1-800-678-4682 or
1-440-366-0709
For Technical Service Call:
1-800-832-4707
Literature Can Be Found at:
www.invacare.com or
1-800-828-6272
SYMBOL DEFINITION
Examples:
A,B,C etc.
NOTE:
NLA
= Special Comments
= General information pertaining to that specific page
= No Longer Available
HARDWARE MEASUREMENTS
The measurements for the hardware will be listed as follows:
Screws, Bolts
Washers
Spacers
For your convenience, we have supplied an area for you to list your Invacare Representatives.
Tie Wrap (5-5/8" L)147
Locknut (5/16-18)148
Washer, Steel (5/16 x 3/4 x 1/16")199
Bolt, Hex Head Cap (1/4-20 x 3/4")1210
Washer (1/4 x 1/2 x 1/16")1211
Screw, Hex Head w/ Patch (5/16-18 x 7/8")1912
Locknut (1/4-20)1213
Screw, Phillips Pan Head Tap (#10-32 x 1/2")1214
1113357NLA - Kit, Battery Box Door Assembly, 22NF Short1115B,D
Screw, Hex Head w/ Patch (5/16-18 x 7/8")128
Washer, Flat (21/64 x 53/64 x 7/64")129
Screw, Socket Flat Head (1/4-20 x 3/4")1310
Bolt, Hex Head Cap (1/4-20 x 3/4")1311
Washer (1/4 x 1/2 x 1/16")1312
Screw, Hex Head (1/4-20 x 1-5/8")1413
Screw, Phillips Pan Head (#10-32 x 5/8")1414
Bracket, Upper Seat, Front, Black1115
Bracket, Lower Seat, Front, Black1116
Screw, Hex Head w/ Patch (5/16-18 x 3/4")1217
Package, Tie Wrap (5-5/8" L)1218
Locknut (1/4-20)1619
Washer, Flat (3/16 x 5/8 x 1/16")1420
Screw, Phillips Pan Head Tap (#10-32 x 1/2")1221
1125776Kit, Battery Box Door Elevate Assembly, 22NF
To order call toll free 1-800-333-6900, or www.invacare.com
Page 29
Seat Frame and Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart#1 Seat Frame with Hardware 111
1029501Plug Button, Black (1")122
1090768Kit, Lock Handle w/Rivets (Pair)213
47471X074Spring, Arm Lock124
1028594Pin, Arm Lock, Black125
(16"-22" Wide)
Elevate Only For ASBA Seating (Before 7/5/05)
Form No. 04-041
28
To order call toll free 1-800-333-6900, or www.invacare.com
Page 30
ADJASBA Seat Frame, Seat Pan and Hardware
(16"-20" Wide) x (16"-22" Deep) After 7/4/05
Form No. 04-041
29
To order call toll free 1-800-333-6900, or www.invacare.com
Page 31
ADJASBA Seat Frame, Seat Pan and Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1120288Frame, Center Seat, Black111D
1122475Crossbar, Seat Frame (16" - 20" W)142
1122647Rail, Seat Frame (16 - 20" D For Formula TRE and
16 - 19" D For ADJASBA)
123
1122677Rail, Seat Frame (20 - 22" D Formula TRE) (19 -
22" D ADJASBA)
123
1124386Pan, Seat with Hook and Loop Fasteners (16 - 20"
W) x (16 - 20" D For Formula TRE) & (16 - 19" D
For ADJASBA)
114
1124666Pan, Seat, with Hook and Loop Fasteners (16 - 20"
W) x (20 - 22" D For Formula TRE) & (19 - 22" D
For ADJASBA)
114
1043082Hook Fastener with Adhesive Back (2" W x 18" L)125A
1044580Loop Fastener with Adhesive Back (2" W x 18" L)125A
1043084Hook Fastener with Adhesive back (2" W x 22" L)125B
1044584Loop Fastener with Adhesive back (2" W x 22" L)125B
1135501Kit, Seat Frame Assembly Hardware116C
Screw, Hex Head w/ Patch (1/4-20 x 3/4")187
Washer (1/4 x 1/2 x 1/16")128
Spacer, Coved (1/4 x 11/16 x 1/2")149
Screw, Socket Button (1/4-20 x 3/4")1210
Pin, Roll (3/16 x 1")1211
1114823Decal, Seat Adjustment Warning1212
A - For 16"-19" deep seats
B - For 19"-22" deep seats
C - Includes items 7-11
D - When ordering Center Seat Frame (item 1), also order 2 ea. Seat Adjustment Warning Decal (item 12).
NOTE:
(16"-20" Wide) x (16"-22" Deep) After 7/4/05
Form No. 04-041
30
To order call toll free 1-800-333-6900, or www.invacare.com
Page 32
ADJASBA Seat Frame, Seat Pan and Hardware
(20"-22" Wide) x (16"-22" Deep) After 7/4/05
Form No. 04-041
31
To order call toll free 1-800-333-6900, or www.invacare.com
Page 33
ADJASBA Seat Frame, Seat Pan and Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1120288Frame, Center Seat, Black111D
1120283Crossbar, Seat Frame (20" - 24" W)142
1122647Rail, Seat Frame (16 - 20" D For Formula TRE and
16 - 19" D For ADJASBA)
123
1122677Rail, Seat Frame (20 - 22" D Formula TRE) (19 -
22" D ADJASBA)
123
1124388Pan, Seat, with Hook and Loop Fasteners (20 - 24"
W) x (16 - 20" D For Formula TRE) & (16 - 19" D
For ADJASBA)
114
1124667Pan, Seat with Hook and Loop Fasteners (20 - 24"
W) x (20 - 22" D For Formula TRE) & (19 - 22" D
For ADJASBA)
114
1043082Hook Fastener with Adhesive Back (2" W x 18" L)125A
1044580Loop Fastener with Adhesive Back (2" W x 18" L)125A
1043084Hook Fastener with Adhesive back (2" W x 22" L)125B
1044584Loop Fastener with Adhesive back (2" W x 22" L)125B
1135501Kit, Seat Frame Assembly Hardware116C
Screw, Hex Head w/ Patch (1/4-20 x 3/4")187
Washer (1/4 x 1/2 x 1/16")128
Spacer, Coved (1/4 x 11/16 x 1/2")149
Screw, Socket Button (1/4-20 x 3/4")1210
Pin, Roll (3/16 x 1")1211
1114823Decal, Seat Adjustment Warning1212
A - For 16"-19" deep seats
B - For 19"-22" deep seats
C - Includes items 7-11
D - When ordering Center Seat Frame (item 1), also order 2 ea. Seat Adjustment Warning Decal (item 12).
NOTE:
(20"-22" Wide) x (16"-22" Deep) After 7/4/05
Form No. 04-041
32
To order call toll free 1-800-333-6900, or www.invacare.com
Page 34
Seat Frame, Seat Pan and Hardware
(16"-20" Wide x 16"-22" Deep Conventional)
and (16", 18", 20" Wide x 16"-22" Deep Contoura) Seating
Form No. 04-041
33
To order call toll free 1-800-333-6900, or www.invacare.com
Page 35
Seat Frame, Seat Pan and Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1122676Frame, Center Seat, Black
For Conventional and Contoura Seating
111
1122475Crossbar, Seat Frame (16" - 20" W)142
1122647Rail, Seat Frame (16 - 20" D For Formula TRE and
16 - 19" D For ADJASBA)
123A
1122677Rail, Seat Frame (20 - 22" D Formula TRE) (19 -
22" D ADJASBA)
123B
1124386Pan, Seat with Hook and Loop Fasteners (16 - 20"
W) x (16 - 20" D For Formula TRE) & (16 - 19" D
For ADJASBA)
114A
1124666Pan, Seat, with Hook and Loop Fasteners (16 - 20"
W) x (20 - 22" D For Formula TRE) & (19 - 22" D
For ADJASBA)
114B
1043082Hook Fastener with Adhesive Back (2" W x 18" L)125A
1044580Loop Fastener with Adhesive Back (2" W x 18" L)125A
1043084Hook Fastener with Adhesive back (2" W x 22" L)125B
1044584Loop Fastener with Adhesive back (2" W x 22" L)125B
1125737Kit, Seat Frame Assembly Hardware116D,E
Screw, Hex Head w/ Patch (1/4-20 x 3/4")187
Washer (1/4 x 1/2 x 1/16")148
Pin, Roll (3/16 x 1")129
Spacer, Coved (1/4 x 11/16 x 1/2")1610
Locknut (1/4-20)1211
Screw, Socket Button Head (1/4-20 x 1-1/2") 1212
Screw, Socket Button (1/4-20 x 3/4")1212
A - For 16"-20" deep Conventional and 16"-18" deep Contoura Seating
B - For 20"-22" deep Conventional and 19"-21" deep Contoura Seating
D - Includes items 7-12
E - After 7/4/05 Threaded Inserts were added to the Center Seat Frame. Items 10 and 11 were no longer needed for item 12
screw. Item 12 was shortened to 3/4" long.
NOTE:
(16"-20" Wide x 16"-22" Deep Conventional)
and (16", 18", 20" Wide x 16"-22" Deep Contoura) Seating
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
34
Page 36
Seat Frame, Seat Pan and Hardware
(20"-24" Wide x 16"-22" Deep Conventional)
and (20", 22", 24" Wide x 16"-22" Deep Contoura) Seating
Form No. 04-041
35
To order call toll free 1-800-333-6900, or www.invacare.com
Page 37
Seat Frame, Seat Pan and Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1122676Frame, Center Seat, Black
For Conventional and Contoura Seating
111
1120283Crossbar, Seat Frame (20" - 24" W)142
1122647Rail, Seat Frame (16 - 20" D For Formula TRE and
16 - 19" D For ADJASBA)
123A
1122677Rail, Seat Frame (20 - 22" D Formula TRE) (19 -
22" D ADJASBA)
123B
1131445Rail, Seat Frame (22" D)123C
1124388Pan, Seat, with Hook and Loop Fasteners (20 - 24"
W) x (16 - 20" D For Formula TRE) & (16 - 19" D
For ADJASBA)
114A
1124667Pan, Seat with Hook and Loop Fasteners (20 - 24"
W) x (20 - 22" D For Formula TRE) & (19 - 22" D
For ADJASBA)
114B
1131448Pan, Seat, with Hook and Loop Fasteners (20 - 24"
W x 22" D)
114C
1043082Hook Fastener with Adhesive Back (2" W x 18" L)125A
1044580Loop Fastener with Adhesive Back (2" W x 18" L)125A
1043084Hook Fastener with Adhesive back (2" W x 22" L)125B,C
1044584Loop Fastener with Adhesive back (2" W x 22" L)125B,C
1125737Kit, Seat Frame Assembly Hardware116D,E
Screw, Hex Head w/ Patch (1/4-20 x 3/4")187
Washer (1/4 x 1/2 x 1/16")148
Pin, Roll (3/16 x 1")129
Spacer, Coved (1/4 x 11/16 x 1/2")1610
Locknut (1/4-20)1211
Screw, Socket Button Head (1/4-20 x 1-1/2") 1212
Screw, Socket Button (1/4-20 x 3/4")1212
A - For 16"-20" deep Conventional and 16"-18" deep Contoura Seating
B - For 20"-22" deep Conventional and 19"-21" deep Contoura Seating
C - 22" deep Contoura Seating
D - Includes items 7-12
E - After 7/4/05 Threaded Inserts were added to the Center Seat Frame. Items 10 and 11 were no longer needed for item 12
screw. Item 12 was shortened to 3/4" long.
NOTE:
(20"-24" Wide x 16"-22" Deep Conventional)
and (20", 22", 24" Wide x 16"-22" Deep Contoura) Seating
Form No. 04-041
36
To order call toll free 1-800-333-6900, or www.invacare.com
Page 38
Seat Frame Mounting Hardware
Elevate Only For ASBA Seating (Before 7/5/05)
Form No. 04-041
37
To order call toll free 1-800-333-6900, or www.invacare.com
1021742Screw, Phillips Pan Head (#4-40 x 1/2")114
1025195Locknut (1/4-20)125
1160374Bracket, MK6i Connector, Black116
1009838Screw, Socket Button (1/4-20 x 3/4")127
A - Includes items 2-7. Kit is used for Conventional and Contoura Seating
NOTE:
For Formula Recline and Tilt/Recline
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
60
Page 62
Seat Pan and Mounting Hardware
Elevate Only For ASBA Seating (Before 7/5/05)
Form No. 04-041
61
To order call toll free 1-800-333-6900, or www.invacare.com
Page 63
Seat Pan and Mounting Hardware
#1 Seat Pan
16" Deep - 18" Deep
Chair Width16" Deep17" Deep18" Deep
10660351066024106601316" W
10660361066025106601417" W
10660371066026106601518" W
10660381066027106601619" W
10660391066028106601720" W
10660401066029106601821" W
10660411066030106601922" W
#1 Seat Pan
19" Deep - 22" Deep
Chair Width19" Deep20" Deep21" Deep22" Deep
106607910660681066057106604616" W
106608010660691066058106604717" W
106608110660701066059106604818" W
106608210660711066060106604919" W
106608310660721066061106605020" W
106608410660731066062106605121" W
106608510660741066063106605222" W
Elevate Only For ASBA Seating (Before 7/5/05)
Form No. 04-041
62
To order call toll free 1-800-333-6900, or www.invacare.com
Page 64
Seat Pan and Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart#1 Seat Pan 16"-18" Depth111
See Chart#1 Seat Pan 19"-22" Depth111
1070459Kit, Seat Pan Mounting Hardware116
Screw, Hex Head (1/4-20 x 1-5/8")122
Screw, Hex Head (1/4-20 x 1-1/2") 143
Spacer (1/4 x 3/8 x 3/16")144
Locknut (1/4-20)165
Elevate Only For ASBA Seating (Before 7/5/05)
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
63
Page 65
Seat Cushion Assembly
#1 Contoura Seat Cushion Assembly
NOTE: To order a Mesh Contoura Seat Cushion Assembly, please use quote # SM-100908010838 when
placing your order.
Chair Width21" Deep22" Deep16" Deep17" Deep18" Deep19" Deep20" Deep
N/AN/A
1132986
1132985
1132984
1132983
1132982
16" Wide
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
N/AN/A
1132991
1132990
1132989
1132988
1132987
18" Wide
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1132998
1132997
1132996
1132995
1132994
1132993
1132992
20" Wide
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1133003
1133002
1133001
1133000
1132999
N/AN/A22" Wide
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1133008
1133007
1133006
1133005
1133004
N/AN/A24" Wide
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
A - Cushion Foam is not available separately. NOTE:
Contoura Seating
64
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
Page 66
Seat Cushion Assembly
#2 Contoura Seat Cushion Cover Before 12/16/10
Chair Width21" Deep22" Deep16" Deep17" Deep18" Deep19" Deep20" Deep
Contoura Seat Cushion Covers listed on this chart are No Longer Available. Refer to the Contoura Seat Cushion Covers dated after 12/15/10
as a direct replacement.
Contoura Seating
Form No. 04-041
65
To order call toll free 1-800-333-6900, or www.invacare.com
Page 67
Seat Cushion Assembly
#2 Contoura Seat Cushion Cover After 12/15/10
Chair Width21" Deep22" Deep16" Deep17" Deep18" Deep19" Deep20" Deep
To order call toll free 1-800-333-6900, or www.invacare.com
Page 68
Back Upholstery, Nylon
Single Liners
Width
16"-17"
High
18"-19"
High
20"
High
21"-22"
High
23"-24"
High
1054529104515910689471045207104517516" W
1054530104516010689481045208104517617" W
1054531104516110689491045209104517718" W
Elevate Only For ASBA/ADJASBA Seating
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
67
Page 69
Back Upholstery, Nylon
Dual Liners
Width
16"-17"
High
18" - 19"
High
20"
High
21" - 22"
High
23" - 24"
High
1054534104516410689521045212104518016" W
1054535104516510689531045213104518117" W
1054536104516610689541045214104518218" W
1054537104516710689551045215104518319" W
1054538104516810689561045216104518420" W
1054539104516910689571045217104518521" W
1054540104517010689581045218104518622" W
NOTE: Dual liner back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18".
Back Upholstery Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See ChartSingle Liners11A
See ChartDual Liners - Nylon 11A
1026298Package, Screw with Washer (#10 x 7/8") (Pair)21A
A - Not Shown
NOTE:
Elevate Only For ASBA/ADJASBA Seating
Form No. 04-041
68
To order call toll free 1-800-333-6900, or www.invacare.com
Page 70
Conventional Back without Mounting Hardware
NOTE: Extruded back canes come in one back height only. Back cane material height for extruded back
canes measure approximately 20-1/2". Overall back height from the seat pan to top of the extruded back
cane is approximately 22-1/2". Only the Back Assembly needs to be replaced when changing back
heights.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No. 04-041
69
To order call toll free 1-800-333-6900, or www.invacare.com
Page 71
Conventional Back without Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart#1 Back Assembly without Hardware 16"-20" Wide111
See Chart#1 Back Assembly without Hardware 21"-24" Wide111
See Chart#2 Back Pan with Vinyl Edge Trim 16"-20" Wide112
See Chart#2 Back Pan with Vinyl Edge Trim 21"-24" Wide112
See Chart#3 Back Cushion Assembly 16"-20" Wide113
See Chart#3 Back Cushion Assembly 21"-24" Wide113
Back cover and foam are sold as a back cushion assembly only. Chart reflects chair width and the actual back cushion width will be 1" wider
than the chair width.
Back cover and foam are sold as a back cushion assembly only. Chart reflects chair width and the actual back cushion width will be 1" wider
than the chair width.
NOTE: Extruded back canes come in one back height only. Back cane material height for extruded back
canes measure approximately 20-1/2". Overall back height from the seat pan to top of the extruded back
cane is approximately 22-1/2". Only the Back Assembly needs to be replaced when changing back
heights.
NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested.
This will allow the Loop Fastener Adhesive on the Back Cover to attach properly.
Form No. 04-041
73
To order call toll free 1-800-333-6900, or www.invacare.com
Page 75
Contoura Back without Mounting Hardware - Before
5/15/09
NOTE: When changing seat width on any system that has Recline and Contoura Seating (Tilt/Recline,
Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246 for directions
on how to order the Back and all additional components that may be required for changing seat width
through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights. Contoura Backs for ADJASBA Seating do not use the 24" wide selection
Form No. 04-041
74
To order call toll free 1-800-333-6900, or www.invacare.com
Page 76
Contoura Back without Mounting Hardware - Before
5/15/09
NOTE: When changing seat width on any system that has Recline and Contoura Seating (Tilt/Recline,
Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246 for directions
on how to order the Back and all additional components that may be required for changing seat width
through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights. Contoura Backs for ADJASBA Seating do not use the 24" wide selection
Form No. 04-041
75
To order call toll free 1-800-333-6900, or www.invacare.com
Page 77
Contoura Back without Mounting Hardware - Before
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart#1 Back Assembly without Hardware 16", 18", 20",
22", 24" Wide
111
See Chart#2 Back Pan with Vinyl Edge Trim 16", 18", 20", 22",
24" Wide
112
See Chart#3 Back Cushion Assembly 16", 18", 20", 22", 24"
Wide
113
1125725Hook Fastener w/ Adhesive Back (1" W x 48" L)114
1125724Trim, Edge, Cut-To-Length, Vinyl Black (96" L) 115
5/15/09
NOTE: When changing seat width on any system that has Recline and Contoura Seating (Tilt/Recline,
Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246 for directions
on how to order the Back and all additional components that may be required for changing seat width
through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights. Contoura Backs for ADJASBA Seating do not use the 24" wide selection
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
76
Page 78
Contoura Back without Mounting Hardware - Before
#1 Back Assembly without Hardware 16", 18", 20", 22", 24" Wide
NOTE: When changing seat width on any system that has Recline and Contoura Seating (Tilt/Recline, Tilt/Recline/Elevate or Recline Only)
you must First look up special quote # C-100628042246 for directions on how to order the Back and all additional components that may be
required for changing seat width through the Equipment Configurator.
#2 Back Pan with Vinyl Edge Trim 16", 18", 20", 22", 24" Wide
Overall
Back
Height
24" Wide
Material
Back
Height
16" Wide18" Wide20" Wide22" Wide
1131409
1131408-NLA
11314071131406113140520"25"
See Note(s) A
1131412113141111224531122454113141024"29"
A - Item is No Longer Available. Back Assembly, part # 1132831 must be purchased for replacement. NOTE:
#3 Back Cushion Assembly 16", 18", 20", 22", 24" Wide
Overall
Back
Height
24" Wide
Material
Back
Height
16" Wide18" Wide20" Wide22" Wide
1132824-NLA
113282311328221132821113282020"25"
See Note(s) B
1132819-NLA
113281811256421125641113281724"29"
See Note(s) A
A - Item is No Longer Available. Back Assembly, part # 1132827 must be purchased for replacement.
B - Item is No Longer Available. Back Assembly, part # 1132832 must be purchased for replacement.
NOTE:
5/15/09
NOTE: When changing seat width on any system that has Recline and Contoura Seating (Tilt/Recline,
Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246 for directions
on how to order the Back and all additional components that may be required for changing seat width
through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights. Contoura Backs for ADJASBA Seating do not use the 24" wide selection
Form No. 04-041
77
To order call toll free 1-800-333-6900, or www.invacare.com
Page 79
Curve Contoura Back w/o Mounting Hardware - After
5/14/09
NOTE: When changing seat width on any system that has Recline and Curve Contoura Seating
(Tilt/Recline, Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246
for directions on how to order the Back and all additional components that may be required for changing
seat width through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights.
Form No. 04-041
78
To order call toll free 1-800-333-6900, or www.invacare.com
Page 80
Curve Contoura Back w/o Mounting Hardware - After
5/14/09
NOTE: When changing seat width on any system that has Recline and Curve Contoura Seating
(Tilt/Recline, Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246
for directions on how to order the Back and all additional components that may be required for changing
seat width through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights.
Form No. 04-041
79
To order call toll free 1-800-333-6900, or www.invacare.com
Page 81
Curve Contoura Back w/o Mounting Hardware - After
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
See Chart#1 Curved Contoura Back Kit111A
See Chart#1 Mesh Curved Contoura Back Kit (CTBMSH)111A
See Chart#3 Curve Contoura Back Cushion Assembly113B
See Chart#3 Mesh Curve Contoura Back Cushion Assembly
(CTBMSH)
113B
1166151Kit, Lateral Support, Contoura Back (22" H) (Pair)116C
Screw, Socket, Button (1/4-20 x 3/8")14
Support, Lateral (22" H)12
1163130Kit, Lateral Support, Contoura Back (25" H) (Pair)116C
Screw, Socket, Button (1/4-20 x 3/8")147
Support, Lateral (25" H)128
1163131Kit, Lateral Support, Contoura Back (28" H) (Pair)116C
Screw, Socket, Button (1/4-20 x 3/8")147
Support, Lateral (28" H)128
1084410Support, Lumbar - Large119
A - Includes Items 2 thru 9.
B - Includes Items 4 and 5. Back Cover and Foam are sold as a Back Cushion Assembly only.
C - Included Items 7 and 8.
Item
#2 is a non-saleable part. Refer to item #1 Kit when ordering.
NOTE:
#1 Curved Contoura Back Kit
Overall
Back
Height
24" Wide
Material
Back
Height
16" Wide18" Wide20" Wide22" Wide
1165850
1165849
1165848
1165847
1165846
17" High22" High
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1161488
1161486
1161484
1161482
1161480
20" High25" High
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1161489
1161487
1161485
1161483
1161481
23" High28" High
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
A - Includes items 2-9 NOTE:
NOTE: When changing seat width on any system that has Recline and Curve Contoura Seating (Tilt/Recline, Tilt/Recline/Elevate or Recline
Only) you must First look up special quote # C-100628042246 for directions on how to order the Back and all additional components that may
be required for changing seat width through the Equipment Configurator.
Overall Back Height includes the spacing gap dimension from the bottom of the Back Assembly to the Seat Pan
5/14/09
NOTE: When changing seat width on any system that has Recline and Curve Contoura Seating
(Tilt/Recline, Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246
for directions on how to order the Back and all additional components that may be required for changing
seat width through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights.
Form No. 04-041
80
To order call toll free 1-800-333-6900, or www.invacare.com
Page 82
Curve Contoura Back w/o Mounting Hardware - After
#1 Mesh Curved Contoura Back Kit (CTBMSH)
Overall
Back
Height
24" Wide
Material
Back
Height
16" Wide18" Wide20" Wide22" Wide
1165845
1165844
1165843
1165842
1165837
17" High22" High
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1164243
1164241
1164239
1164237
1164235
20" High25" High
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
1164244
1164242
1164240
1164238
1164236
23" High28" High
See Note(s) ASee Note(s) ASee Note(s) ASee Note(s) ASee Note(s) A
A - Includes items 2-9 NOTE:
NOTE: When changing seat width on any system that has Recline and Curve Contoura Seating (Tilt/Recline, Tilt/Recline/Elevate or Recline
Only) you must First look up special quote # C-100628042246 for directions on how to order the Back and all additional components that may
be required for changing seat width through the Equipment Configurator.
5/14/09
NOTE: When changing seat width on any system that has Recline and Curve Contoura Seating
(Tilt/Recline, Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246
for directions on how to order the Back and all additional components that may be required for changing
seat width through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights.
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
81
Page 83
Curve Contoura Back w/o Mounting Hardware - After
#3 Curve Contoura Back Cushion Assembly
Overall
Back
Height
24" Wide
Material
Back
Height
16" Wide18" Wide20" Wide22" Wide
1166150
1166149
1166148
1166147
1166146
17" High22" High
See Note(s) BSee Note(s) BSee Note(s) BSee Note(s) BSee Note(s) B
1163256
1163254
1163252
1163250
1163248
20" High25" High
See Note(s) BSee Note(s) BSee Note(s) BSee Note(s) BSee Note(s) B
1163257
1163255
1163253
1163251
1163249
23" High28" High
See Note(s) BSee Note(s) BSee Note(s) BSee Note(s) BSee Note(s) B
B - Includes items 4 and 5. Back Cover and Foam are sold as a Back Cushion Assembly only. NOTE:
Overall Back Height includes the spacing gap dimension from the bottom of the Back Assembly to the Seat Pan
#3 Mesh Curve Contoura Back Cushion Assembly (CTBMSH)
See Note(s) BSee Note(s) BSee Note(s) BSee Note(s) BSee Note(s) B
1171650
1171648
1171646
1171644
1171642
25" High
See Note(s) BSee Note(s) BSee Note(s) BSee Note(s) BSee Note(s) B
1171651
1171649
1171647
1171645
1171643
28" High
See Note(s) BSee Note(s) BSee Note(s) BSee Note(s) BSee Note(s) B
B - Includes items 4 and 5. Back Cover and Foam are sold as a Back Cushion Assembly only. NOTE:
Overall Back Height includes the spacing gap dimension from the bottom of the Back Assembly to the Seat Pan
5/14/09
NOTE: When changing seat width on any system that has Recline and Curve Contoura Seating
(Tilt/Recline, Tilt/Recline/Elevate or Recline Only) you must First look up special quote # C-100628042246
for directions on how to order the Back and all additional components that may be required for changing
seat width through the Equipment Configurator.
NOTE: Extruded back canes come in one back height only. Back cane material height for the contoura
extruded back canes measure approximately 20-1/2". Overall back height from the seat pan to top of the
extruded back cane is approximately 23". Only the Back Assembly needs to be replaced when changing
back heights.
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
82
Page 84
Back Mounting Hardware
Conventional Tilt - Before 5/15/09
Form No. 04-041
83
To order call toll free 1-800-333-6900, or www.invacare.com
Page 85
Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125757Kit, Back Mounting Hardware For Conventional Tilt111A
Locknut (1/4-20)142
Washer (1/4 x 23/32 x 1/16")183
Spacer, Coved (1/4 x 7/8 x 7/16")144
Spacer (1/4 x 5/8 x 3/8")145
Screw, Socket Button Head (1/4-20 x 2")146
A - Includes items 2-6
NOTE:
Conventional Tilt - Before 5/15/09
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
84
Page 86
Back Mounting Hardware
Conventional Recline and Tilt/Recline - Before 5/15/09
Form No. 04-041
85
To order call toll free 1-800-333-6900, or www.invacare.com
Page 87
Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125756Kit, Back Mounting Hardware For Conventional
Recline and Tilt/Recline
111A
T-Nut (1/4-20)182
Locknut (1/4-20)143
NLA - Bracket, Angled Back, Black144
Washer (1/4 x 1/2 x 1/16")185
Screw, Hex Head w/ Patch (1/4-20 x 1/2")186
Washer (1/4 x 23/32 x 1/16")147
Screw, Socket Button (1/4-20 x 3/4")148
A - Includes items 2-8
NOTE:
Conventional Recline and Tilt/Recline - Before 5/15/09
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
86
Page 88
Back Mounting Hardware
Contoura Tilt - Before 5/15/09
Form No. 04-041
87
To order call toll free 1-800-333-6900, or www.invacare.com
Page 89
Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125755Kit, Back Mounting Hardware For Contoura Tilt111A
T-Nut (1/4-20)1162
Locknut (1/4-20)143
Washer (1/4 x 1/2 x 1/16")1164
Bracket, Back Mounting, Black145
Screw, Hex Head w/ Patch (1/4-20 x 1/2")1166
Washer (1/4 x 23/32 x 1/16")147
Screw, Socket Button (1/4-20 x 3/4")148
Bracket, Contoura Shear Lock Out, Black129
A - Includes items 2-9
NOTE:
Contoura Tilt - Before 5/15/09
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
88
Page 90
Contoura Back Mounting Hardware
ADJASBA Only - Before 5/15/09
Form No. 04-041
89
To order call toll free 1-800-333-6900, or www.invacare.com
Page 91
Contoura Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1140945Kit, Contoura Back Mounting Hdwr. - Round Canes111A
Bracket, Back Mounting, Front, Black142
Screw, Phillips Oval Head (#10-16 x 7/8")123
Screw, Socket Button (1/4-20 x 3/4")184
Washer (1/4 x 23/32 x 1/16")185
Locknut (1/4-20)186
Bracket, Back Mounting, Rear, Black147
A - Includes items 2-7
NOTE:
ADJASBA Only - Before 5/15/09
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
90
Page 92
Back Mounting Hardware
Contoura Recline and Tilt/Recline - Before 5/15/09
Form No. 04-041
91
To order call toll free 1-800-333-6900, or www.invacare.com
Page 93
Back Mounting Hardware
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125754Kit, Back Mounting Hardware For Contoura Recline
and Tilt/Recline
111A
T-Nut (1/4-20)142
Bracket, Back Mounting, Black123
Washer (1/4 x 1/2 x 1/16")144
Screw, Hex Head w/ Patch (1/4-20 x 1/2")145
Locknut (1/4-20)166
Washer (1/4 x 23/32 x 1/16")167
Screw, Socket Button (1/4-20 x 3/4")168
A - Includes items 2-8
NOTE:
Contoura Recline and Tilt/Recline - Before 5/15/09
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
92
Page 94
Curve Contoura Mounting Back Hardware - After 5/14/09
Form No. 04-041
93
To order call toll free 1-800-333-6900, or www.invacare.com
Page 95
Curve Contoura Mounting Back Hardware - After 5/14/09
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1157925Kit, Metal Curved and Curve Contoura Back
Mounting Hardware
111A
Spacer, Back Pan, Black142
Hook, Back Assembly Mounting143
Screw, Socket Button Head (1/4-20 x 1")144
Washer (1/4 x 23/32 x 1/16")185
Screw, Phillips Oval Head (#10-16 x 7/8")126
Locknut (1/4-20)147
A - Includes Items 2 thru 7.
NOTE:
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
94
Page 96
Prop Rod Assembly
Contoura Tilt
Form No. 04-041
95
To order call toll free 1-800-333-6900, or www.invacare.com
Page 97
Prop Rod Assembly
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125764Kit, Prop Rod Assembly Contoura Tilt111B,C,A
Screw, Shoulder Hex Socket (3/8 x 2", 5/16-18)112
Washer, Flat (5/16 x 5/8 x 1/16")113
Locknut (5/16-18)124
Kit, Top Prop Rod with Bushings115
Tube, Middle Prop Rod, Black116
Kit, Bottom Prop Rod Tube with Bushings117
Screw, Socket Head w/ Patch (3/8-16 x 1-1/2")128
Locknut, Low Profile (3/8-16)129
Screw, Shoulder Hex Socket Head (3/8 x 1-3/4",
5/16-18)
1110
Bushing, Actuator Motor (3/8 x 3/4 x 5/32")1211
Spacer (3/8 x 1 x 1/2")1112
A - Includes items 2-12
B - When a vent tray is present, item 11 located on the top side of the prop rod is replaced with item 12
C - Relocation of holes were made 7/5/05 for items 5, 6 and 7. Item 1 must be ordered for chairs manufactured before 7/5/05.
NOTE:
Contoura Tilt
Form No. 04-041
To order call toll free 1-800-333-6900, or www.invacare.com
96
Page 98
Back Recline Shear Link Assemblies
Form No. 04-041
97
To order call toll free 1-800-333-6900, or www.invacare.com
Page 99
Back Recline Shear Link Assemblies
Item
Number
Part Number
DescriptionNote
Quantity Per
Package Assembly
1125758Kit, Recline Shear Link Assembly Conventional
(Pair)
111A
Screw, Hex Head w/ Patch (1/4-20 x 5/8")142
Washer (1/4 x 1/2 x 1/16")143
Plate, Shear Adapter124
T-Nut (1/4-20)145
Locknut, Low Profile (3/8-16)146
Washer, Flat (3/8 x 11/16 x 1/16")147
Link, Recline Shear, Black - Right118
Link, Recline Shear, Black - Left118
Stand-Off, Recline Shear Link149
1168997Kit, Recline Shear Link Assembly, Contoura/Curve
Contoura (Pair)
1110B
Screw, Hex Head w/ Patch (1/4-20 x 5/8")1411
Washer (1/4 x 1/2 x 1/16")1412
T-Nut (1/4-20)1413
Locknut, Low Profile (3/8-16)1414
Washer, Flat (3/8 x 11/16 x 1/16")1415
Link, Recline Shear, Black - Right1116
Link, Recline Shear, Black - Left1116