Invacare H112-5 User Manual
Bath Board
Model H112-5
FC Manuel de l’utilisateur........... page 7
User Manual
DEALER: This manual MUST be given to the user of the product.
USER:
BEFORE using this product, read this manual and save for
future reference.
1 General
1.1 Symbols
Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. See the information below for definitions of the signal words.
WARNING
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Caution indicates a potentially hazardous situation which, if not avoided, may result in property damage or minor injury or both.
This product complies with Directive 93/42/EEC concerning medical devices.
1.2 Life
The expected service life of the product is one year when used in accordance with the safety instructions,
maintenance intervals and correct use, stated in this manual. Effective service life can vary according to
frequency and intensity of use. Maintenance and inspection should be done at least every six months.
1.3 Weight Limitation
The weight limitation of this product is 330 lbs (150 kg).
Part No 1167609 1 Bath Board
Gives useful tips, recommendations and information for efficient, trouble-free use.
1.4 Product Labeling and Product Specifications
Product Weight Limitation
Date Code
EU Representative
27” (69 cm)
13” (33 cm)
Product Model
Number
2 Safety
2.1 Intended Use
The bath board is intended to be used inside the bathtub. All other use can cause risk of injury.
2.2 General Warnings
Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact carrier/ dealer for further instruction.
WARNING
DO NOT USE THIS PRODUCT OR ANY AVAILABLE OPTIONAL EQUIPMENT
WITHOUT FIRST COMPLETELY READING AND UNDERSTANDING THESE
INSTRUCTIONS AND ANY ADDITIONAL INSTRUCTIONAL MATERIAL SUCH
AS OWNER’S MANUALS, SERVICE MANUALS OR INSTRUCTION SHEETS
SUPPLIED WITH THIS PRODUCT OR OPTIONAL EQUIPMENT. IF YOU ARE
UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS OR
INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL, DEALER OR
TECHNICAL PERSONNEL BEFORE ATTEMPTING TO USE THIS EQUIPMENT OTHERWISE, INJURY OR DAMAGE MAY OCCUR.
ACCESSORIES WARNING
Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products.
WARNING
Users with limited physical capabilities should be supervised or assisted when using this product.
Always test to see that the bath board is properly and securely locked in place on the bath tub before using.
Ensure all hardware is tight at all times.
Bath Board 2 Part No 1167609
3 Usage
B
C
A
3.1 Installing the Bath Board WARNING: Risk of Falling.
The bath board MUST BE installed properly.
ALWAYS install the bath board at least .78 in (2 cm) away from tub fixtures.
At least .78 in (2 cm) of the bath board MUST hang over the outside of the tub.
Maximum Tub Wall Thickness: .78 in (20 mm)
Maximum Tub Width: 24.8 in (630 mm)
Minimum Tub Width: 15.5 in (395 mm)
DO NOT use the bath board with tubs that
have no inner wall.
1. Place the bath board (A) onto a hard, flat
surface.
2. Align the handle (B) with the proper mounting
hole in the bath board.
3. Press the bath board handle into the mounting
4. Ensure the handle latches securely into the bath
5. Ensure the handle cannot be pulled out of the
Part No 1167609 3 Bath Board
One mounting hole is round and the other mounting hole is square.
holes (C).
board.
bath board after installation.
6. Twist the mounting pin (D) clockwise to
E
D
F
6
7-8
12
13
15
16
17
G
remove from the mounting peg (E).
7. Position the mounting pin into the opening in
the slot (F).
8. Position the mounting peg under the bath
board and onto the mounting pin.
9. Twist the mounting peg clockwise to secure
it to the mounting pin.
10. Repeat STEPS 4 to 7 for the remaining three
mounting pegs.
11. Turn the bath board over.
12. Twist each mounting peg counterclockwise
to loosen.
13. Slide the mounting pegs towards the middle
of the bath board.
14. Turn the bath board over.
15. Position the bath board in the tub.
16. Slide the mounting pegs towards the ends of
17. Turn the mounting pegs counterclockwise to
18. Insert plugs (G) into the openings in the slots.
the bath board.
secure the bath board in the tub. Torque to
53 in-lb (6 Nm).
Bath Board 4 Part No 1167609
Loading...