Invacare 9153644018, 9153644014 User Manual
Installing Front Riggings on the At’m
Assembly, Installation and Operating Instructions
Kit Numbers: 9153644014, 9153644018
SAVE THESE INSTRUCTIONS
NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact
Carrier/Invacare for further instructions.
Safety Summary
To ensure the safe and proper installation and use of the front riggings on the At’m, these
instructions MUST be followed:
WARNING
After ANY adjustments, repair or service and BEFORE use, make sure that all
attaching hardware is tightened securely - otherwise injury or damage may result.
Invacare products are specifically designed and manufactured for use in conjunction
with Invacare accessories. Accessories designed by other manufacturers have not
been tested by Invacare and are not recommended for use with Invacare products.
Description of the Kit
Kit Numbers 9153644014 and 9153644018 for Red or Blue At’m Front Riggings contain:
PART NUMBER DESCRIPTION QUANTITY
1132651 Right Legrest Support Assembly 1
1132652 Left Legrest Support Assembly 1
1133151 Mounting Hardware Assembly 1
1134702 70° Complete Right Footrest Assembly 1
1134703 70° Complete Left Footrest Assembly 1
Installing Front Rigging Support Brackets
NOTE: For this procedure, refer to FIGURE 1.
NOTE: Perform the following steps one (1) side at a time.
1. Remove the plug button from the seat frame tube.
2. Note the orientation of the hardware that connects front seat support tube to the seat
frame tube.
3. Remove the mounting screw, coved washers, spacers, washers and locknut securing
front seat support tube to the seat frame tube. DO NOT discard.
For more information regarding Invacare products, parts, and services,
please visit www.invacare.com
Part No 1130250 1 Installing Front Riggings on the At’m
4. Insert the proper (right or left) front rigging support bracket into the seat frame
tube until two (2) of the four (4) mounting holes on the front rigging support
bracket are aligned with the two (2) mounting holes in the seat frame tube.
CAUTION
Two (2) mounting screws are used to secure the front rigging support
bracket to the seat frame tube for any mounting position used.
5. Install the existing mounting screw, coved washers, spacers, washers and
locknut that secure front seat support tube to the seat frame tube in the
orientation noted in STEP 2. DO NOT tighten locknut at this time.
6. Install the new mounting screw, spacer and locknut (hardware supplied)
through the large mounting hole on the seat frame tube. Securely tighten.
NOTE: Make sure that the spacer is aligned with the large mounting hole in the seat frame
tube and is properly seated against the front rigging support bracket during and after
tightening. Refer to Detail “A” of FIGURE 1.
7. Tighten the locknut securing the front seat tube to the seat frame until it is snug
and then turn an extra 1/8-turn. DO NOT over-tighten as this is a pivot joint
when folding the seat.
8. Repeat STEPS 1-7 to install the front rigging support bracket on the other side.
Seat Frame Tube
Existing Mounting
DETAIL “A”
*Large
Mounting Hole
Spacer
*NOTE: Mounting hole
arrangement on 16-inch wide
seat shown. On the 18-inch
wide seat, the mounting hole
Spacer
Locknut
Screw
Spacer
*Small
Mounting Hole
Front Seat
Support Tube
New Mounting
Screw
Locknut
Spacer
Coved Washers
Front Rigging
Support
Bracket
Front Seat
Support
Tube
Seat Frame Tube
Mounting Holes
on Front Riggings
Support Bracket
Front Rigging
Support
Bracket
positions are reversed.
FIGURE 1 Installing Front Rigging Support Brackets
Installing Front Riggings on the At’m 2 Part No 1130250
Loading...