INSTALLATION
RC SERIES
REMOTE CONTROLS
OPERATION &
SERVICE MANUAL
SINGLE CHANNEL RADIO RECEIVERS
Model: RC613, RC613L Switching Module / Model: RC615 Timer Override Module
For indoor and outdoor use, suitable for Pool/Spa equipment control
ELECTRICAL RATING: 15 Amp Resistive, 1200 Watt Tungsten, 1 HP Motor Load - 120 Volt.
THIS DEVICE COMPLIES WITH FCC RULES PART 15. Operation of this device is subject to the following two conditions
1. This device may not cause harmful interference. 2. This device must accept any interference that may be received,
including interference that may cause undesired operation. FCC rules prohibit adjustments to or modification of receiver and
transmitter circuitry except for replacing the remote control battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
IMPORTANT SAFETY INSTRUCTIONS
1. This Control must be installed by a qualified electrician, according to National and Local Electrical Codes.
2. USE COPPER CONDUCTORS ONLY. If applicable, install this Control not less than 5 feet (3 meters for Canadian
installations) of inside edge of pool or spa.
3. Do not exceed the maximum ratings of individual components, wiring devices, and current carrying capacity of conductors.
4. For grounding of the installation, refer to section 250 and 680 of the National Electrical Code.
5. This Control should not operate any equipment which would cause bodily injury or property damage should it be
activated unexpectedly.
6. Always disconnect electricity at main panel before servicing this Control or the equipment(s) connected to it.
THIS CONTROL IS NOT TO BE USED AS A POWER DISCONNECT.
READ, FOLLOW AND SAVE THIS INSTRUCTION MANUAL
GENERAL INFORMATION
These Modular Radio Receivers are one half of a two part remote control system.
They operate as ordinary ON/OFF switches but they also respond to the signals of
he modules ar
a hand held tr
indoor or outdoor use, and can handle a variety of switching applications, typical
around the house or farm. By the push of a button on the face of the transmitter, the
user is able to turn ON/OFF the connected load (lights, pump, etc.) from any remote
location*, safely and conveniently. In addition, a single transmitter can operate up to
four Receivers and is able to “teach” each Module a different code. (Transmitters are
sold separately).
Model RC613 Receiver Module comes with its own manual ON/OFF button and
it is intended to be installed at the location of the load. The connected load may be
turned ON/OFF using the hand-held transmitter or turned ON/OFF by pushing the red
button on the face of the Receiver.
Model RC613L Receiver Module is the same as RC613 except that it comes with
a long (36 in.) leads.
xtr
e
Model RC615 Receiver Module is the same as the RC613L Module above, except
it has no manual ON/OFF button on its face. This Module is designed to be connected to a timer and will override its pre-set program, without affecting the next
automatic operation. At-site control of the load is possible by the ON/OFF switch of
the timer.
ansmitter - the other half of the system.
T
e designed f
or
* The open field range is 200 feet but depends on many factors like the age of the battery, proximity of
e metal objects,
g
lar
the location of the receiver and environmental conditions at the time of transmission.
1
SPECIFICATIONS AND OTHER INFORMATION
USEFUL INFORMATION
1. Radio Receivers are sensitive to heat. Avoid
mounting them above heater, air conditioner
or exposed to afternoon sun.
2. The higher the Receiver Module, the longer its
range. For good range and reliable reception, install
modules as high as practical above ground level with
antenna at top.
3. Large metal objects divert radio signals. Avoid
mounting Receiver Modules on metal wall, fence
or near large metal objects.
4. Environmental conditions could effect the operation
of the remote control system. For example, in rain
the range may be less than normal.
5. Certain electric equipment like brush type motors
or electronic gas heater igniters emit radio signals
and can effect the function of the Receiver Module.
Avoid mounting modules near such equipment.
6. To prevent electronic interference, install Receiver
Modules at least 3 feet apart.
INSTALLATION
A. ON/OFF Switching Application
- use Model RC613
Make sure the intended load is within the capacity of the
Module, see ratings on page 1 and other choices on page 4.
1. Attach RC613 Receiver Module to the top of an outdoor grade
y is raintight.
e the assemb
junction bo
2. Select the proper location (see Useful Information above) and
install Receiver assembly on a vertical surface or other support,
using har
3. Prepare the necessary conduit runs as required by the installation
layout and pull-in the specified conductors.
4. Follow wiring diagram A on the right, make wire connections
as shown.
5. Turn ON power and test installation, using the ON/OFF button
ace of the Recei
on f
e sur
mak
x. Mak
ware, suitable for the purpose.
d
e the installa
e sur
er Module
v
tion is secur
l
place junction box cover,
. Re
e and raintight.
6. Set code, see Operating Instructions on page 3.
*Ground connections may or may not be as shown.
Diagram
A
2
B. Timer Override Application
- use Model RC615
An existing timer can only be upgraded if the
load connected to the timer is within the
capacity of the Receiver Module. Otherwise,
the timer mechanism must be replaced with
Intermatic Model PT1203M, see also other
choices on page 4.
1. Select the proper location (see Useful
Information on page 2) and install a radio
compatible timer on a vertical surface or
other support, using hardware, suitable for
the purpose.
2. Prepare the necessary conduit runs as required
by the installation layout and pull-in the
specified conductors.
3. Use one of the side knock-outs and a suitable
conduit-L, attach Model RC615 Receiver
Module to timer enclosure.
4. Follow wiring diagram B on the right,
make wire connections as shown.
5. Turn ON power, and test installation,
using the ON/OFF control of the timer.
6. Set code, see operating instructions on page 3.
OPERATION
In case this device is used to operate pool/spa equipment...
DANGER! To Reduce the Risk of Injury:
... do not permit children to operate the Control Unit or use the Pool/Spa unless they are closely supervised at all times.
... test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA! Contact a qualified service technician.
o Set Code
T
A.
Receiver Modules have the capacity to “learn”
and remember a unique code, generated by a
ansmitter will operate only the
he tr
T
ansmitter
tr
designa
In addition, each transmitter can “teach” and
operate up to three different sets of Receivers.
Also, more than one transmitter can be assigned
to oper
1. Turn ON the main power and manually operate the
load a few times, then turn load OFF.
2.
Holding the
Module, press and hold the push button you
choose to operate that particular Module. The red
LED indicator should now be lit.
3. Press the “CODE SET” button on the face of the
Recei
button flashes ONCE (about one second).
.
ted one or more receivers simultaneously.
ate the same Receivers.
Transmitter close to the Receiver
er Module until the green light next to the
v
4. Code setting is now complete. Release the
essing
y pr
utton if it is
ess and hold
pr
h,
witc
tion b
xt to the
ne
ansmitter b
tr
repeatedly on the chosen transmitter button.
The load should cycle ON/OFF, if not repeat
ps 2 and 3 a
ste
If mor
5.
above procedure on the next Receiver Module and
hold down the SAME transmitter button in step 2
if the Module is supposed to function TOGETHER
with the f
supposed to operate INDEPENDENTLY.
ase all memorized codes,
o er
T
CODE SET button on Receiver Module, until the
een indica
r
g
seconds).
To operate a Receiver Module with more than one
ansmitter
tr
battery in transmitters to the same setting.
utton and test installa
ve.
bo
er Module is in use, repeat
e than one Recei
st or a DIFFERENT b
ir
tor light alongside goes out (in about 6
,
set master code s
v
3
LIST OF AVAILABLE MODELS AND COMPONENTS
Model Description Specifications
RC613 Single Channel Receiver 15 Amp Resistive, 10 Amp (1200 Watt) Tungsten,
RC613L Single Channel Receiver 15 Amp Resistive, 10 AMp (1200 Watt) Tungsten,
RC613R Heavy-Duty Receiver 30 Amp Resistive - 120/240 Volt, 12.5 Amp (1500 Watt)
RC615 Single Channel Receiver 15 Amp Resistive, 10 Amp (1200 Watt) Tungsten
RC939
PT1203M
3-way switching module 1 HP Motor Load - 120 Volt
with 36 in. Lead 1 HP - 120 Volt, Single Pole Single Throw Contacts.
and Relay Assembly Tungsten - 120 Volt, 1.5 HP - 120 Volt, 3 HP - 240 Volt
Double Pole Single Throw Contacts..
Timer Override Module 1 HP Motor Load - 120 Volt
3 Channel Transmitter Operates on 9 Volt Battery
24 hr. Timer Mechanical Timer Mechanism Mechanism Only replaces Intermatic T100 Series timers and compatible
with RC615 Receiver. Same rating as RC613R
TROUBLESHOOTING
Symptom Possible Cause(s) Corrective Action
No response to transmitter No power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Turn ON power at main panel
signal at anytime Loose connection(s) at receiver and/or load . . . . . . . . . .Check connections
Transmitter battery dead . . . . . . . . . . . . . . . . . . . . . . . . .Replace battery
Receiver and transmitter are on two different codes . . . .Change code settings (see page 3)
Faulty transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Check battery connections, replace transmitter
Faulty receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace Receiver Module
No response to transmitter Weak Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace battery
signal some of the time Appliance with brush type motor is in use . . . . . . . . . . .Relocate appliance and/or connect to another circuit
Other radio transmitter (police, etc)
is operating nearby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Change master code of transmitter (See page 3)
Receiver is at edge of range . . . . . . . . . . . . . . . . . . . . . . .Mount Receiver closer or higher
Insufficient Range Weak battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace battery
Antenna too close to ground . . . . . . . . . . . . . . . . . . . . . .Relocate Receiver Module
Transmitter is held too close to ground . . . . . . . . . . . . . .Hold transmitter at least 3 ft. above ground
Weak signal due to obstruction . . . . . . . . . . . . . . . . . . . .Remote/relocate Receiver Module
Nuisance oper
a
tion
Other r
is operating nearby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Change master code of transmitter (See page 3)
Fluctuating supply voltage due to surge, etc. . . . . . . . . .If frequent - install surge suppressor
eceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace receiver module
aulty r
F
ansmitter (police
adio tr
ONE YEAR LIMITED W
If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its
sole option, the unit free of charge. This warranty applies only to the original purchaser and is not transferable. This warranty does not apply to: (a) damage
caused by accident, abuse, mishandling, dropping, acts of God, or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken
apart, or otherwise modified; (c) units not used in accordance with instructions (d) damages exceeding the cost of the product. Some stated do not allow a limitation of damages, so the foregoing limitation may not apply to you. this warranty gives you specific legal rights and you may have other rights that vary from
state to state.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AT THE
WARRANTY PERIOD STATED ABOVE.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchase, or (b) mailing postage prepaid to the nearest authorized service center listed. Please be sure to wrap the product securely when mailing to avoid shipping damage. This warranty is made by: Intermatic
Incorporated/After Sales Service, 7777 Winn Rd., Spring Grove, IL 60081-9698/8150675-7000
http://www.intermatic.com
, etc)
ARRANTY
Because of our commitment to continuing research and improvements, Intermatic Incorporated reserves the right to make changes, without notice, in the specifications and material
contained herein and shall not be responsible for any damages, direct or consequential, caused by reliance on the material presented.
INTERMATIC INCORPORATED
158RC9981
http://www
.inter
4
, SPRING GROVE, IL 60081-9698
matic.com
Loading...