Intermatic FL150MH, FL175MH User Manual
HID Flood Light - FL Series
INSTALLATION INSTRUCTIONS
Lamp Types: Metal Halide 150 Watt & 175 Watt
Model: FL150MH & FL175MH
FOR OUTDOOR USE ONLY
NOT FOR USE IN HAZARDOUS ATMOSPHERES
IMPORTANT: Read instruction sheet carefully before installing fixture.
Retain instructions for future reference.
ELECTRICAL REQUIREMENTS
A qualified electrician should complete all required wiring. This fixture will accept 120, 208, 240 or 277
Volts AC and must be properly grounded for safety. A mounting suitable for outdoor use and rated for
wet locations is required. Follow all applicable electrical codes and regulations.
WARNING:
Electric shock hazard
Disconnect power at circuit breaker or fuse box before installing or servicing light.
WARNING:
USE MIN 60˚C SUPPL
CONNECT
Fire hazard
Y CONDUCTORS.
TO SUPPLY IN EXTERNAL
JUNCTION BOX ONLY.
Lamp and housing become very hot during use.
Ensure free air circulation around unit to dissipate heat.
Avoid enclosed locations and locations where flammable debris (leaves, cut grass, etc.) might collect.
Avoid locations where humans or animals might accidentally touch fixture.
WARNING:
Explosion hazard
Never operate light without securing the lens door. When light is operating, the gas in the
lamp inner arc tube is at high pressure.
Never operate light if the fixture lens or outer glass envelope of the lamp is broken or missing.
ARNING:
W
Explosion hazard
Wear safety glasses and gloves when handling lamp. Metal Halide outer envelope is pressurized
and could explode if broken.
WARNING: UV hazard (Metal Halide Lamps Only)
The type of lamp used in this fixture can cause serious skin burn and eye inflammation from short
wave ultraviolet radiation if outer envelope of the lamp is broken or punctured, and the arc tube
continues to operate. Do not use where people will remain for more than a few minutes. Certain
types of lamps that will automatically extinguish when the outer envelope is broken or punctured are
commercially available.
MOUNTING & WIRING
1. Screw the threaded mounting arm of the fixture into 1/2” NPS mounting hole on mounting device.
Mounting
Arm Bolt
Locknut
Figure 1
Screw
Lens
Door
Reflector
Lampholder
Figure 2
Install with Lamp vertical
Screw
2. Using provided twist on or other approved connectors, connect the fixture wires to the supply wires as follows:
(See Figure 3 or Figure 4)
. Identify supply voltage.
a
. Open lens door and remove reflector.
b
c. Select appropriate fixture wire to match incoming voltage. All fixtures are shipped with
appropriate twist on wire connector and strip fixture wire marked with matching voltage.
d. Confirm unused voltage fixture wires are appropriately capped within fixture body.
e. Feed the matching voltage fixture wire through the mounting arm.
f. Replace and secure reflector in the same orientation as shown in Figure 2.
g. Close and secure lens door to prevent damage while wiring fixture to mounting.
. Connect the fixture wire matching the incoming voltage to the black (hot) supply wire.
h
. Connect the fixture wire marked COM to the white (neutral) supply wire.
i
j. Connect the bare copper (fixture ground) wire to the supply grounding wire.
277 V
77 V
CAP
2
40 V
2
208 V
3
X
IGN-01
1
X
LAMP
40 V
2
208 V
LAMP
120 V
OM
C
Metal Halide 150 Watt
Figure 3
COM
3
X
120 V
COM
OM
C
Metal Halide 175 Watt
Figure 4
3. Make sure that all wires and connections are inside the mounting wiring compartment and that the cover is properly
sealed to keep moisture out.
4. Open lens door. Screw lamp into socket in lampholder until finger-tight.
5. Close lens door, making sure that gasket is in place and compressed to seal out moisture. To weatherproof fixture,
seal all holes in housing (mounting conduit, plugs, photocontrols, etc.) with silicone sealant.
6. To operate, restore power to the circuit and switch light on.
CAUTION:
(Metal Halide Lamps Only) Do not use lamp beyond
manufactures rated life to reduce chance of lamp rupture.
Turn lamp off at least once for 15 minutes per week to reduce
chance of lamp rupture.
AIMING FIXTURE
WARNING:
Do not turn mounting arm more than 360˚ after wires are connected. Excessive twisting of wires
may loosen connections.
1. Turn off power at circuit breaker or fuse box. Rotate mounting arm until light is pointing in the
desired direction. Tighten locknut to secure.
2. Loosen mounting arm bolt (do not remove) and tip fixture to desired angle. Retighten bolt to secure.
3. Turn power on and check aim. If adjustment is needed, turn power OFF at circuit breaker or fuse
box and allow fixture to cool before adjusting
Electric shock hazard.
LAMP REPLACEMENT
CAUTION:
1. Turn off power at circuit breaker or fuse box. Allow fixture and lamp to cool.
2. Release retaining clip and swing hinged fixture lens door open . Remove old lamp and replace
with new lamp of correct type and wattage. Screw lamp into socket in lampholder until finger-tight.
Close and secure lens door, making sure that gasket is properly seated, free of debris, and
3.
compressed to seal out moisture.
urn power back on.
T
4.
5. Properly dispose of lamp per manufacturer’s recommendations.
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge.
to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been
subject to unauthorized repair
finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
TIC INCORPORA
INTERMA
TIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES,
INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED
WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOTALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE
ABOVE LIMIT
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage
prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com
Please be sure to wrap the product securely to avoid shipping damage.
TION MA
A
THESE INSTRUCTIONS DO NOT
O FIXTURE INST
T
, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the
NOT BE LIABLE FOR INCIDENTALOR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-
TED WILL
Y TO YOU.
APPL
NOT
Y
TION, OPERA
ALLA
INTERMA
TIC INCORPORA
Use lamp of correct type and wattage as specified on fixture.
ARRANTY
LIMITED 1
TIONS IN EQUIPMENT
ARIA
V
COVER
ALL
TION OR MAINTENANCE. FOR FUR
TED - SPRING GROVE, ILLINOIS 60081 (815) 675-7000 www
YEAR W
, NOR DO
THEY
THER INFORMA
PROVIDE FOR
TION CONT
ACT
.intermatic.com
ALL SITUATIONS RELATED
This warranty is extended
YOUR DISTRIBUT
OR OR
158HL12128
Loading...