Intermatic FL070HPS, FL050HPS, FL035HPS User Manual

HID Flood Light - FL Series

INSTALLATION INSTRUCTIONS
Lamp Types: High Pressure Sodium 35 Watt, 50 Watt, & 70 Watt
Models: FL035HPS, FL050HPS, & FL070HPS

FOR OUTDOOR USE ONLY

NOT FOR USE IN HAZARDOUS ATMOSPHERES

IMPORTANT: Read instruction sheet carefully before installing fixture.

Retain instructions for future reference.

ELECTRICAL REQUIREMENTS

A qualified electrician should complete all required wiring. This fixture is for use with 120V AC only and must be properly
grounded for safety. A mounting suitable for outdoor use and rated for wet locations is required. Follow all applicable
electrical codes and regulations.

WARNING:

Disconnect power at circuit breaker or fuse box before installing or servicing light.

WARNING:

USE MIN 60ºC SUPPLY CONDUCTORS.
CONNECT TO SUPPLY IN EXTERNAL JUNCTION BOX ONLY.
Lamp and housing become very hot during use.
Ensure free air circulation around unit to dissipate heat.
Avoid enclosed locations and locations where flammable debris (leaves, cut grass, etc.) might collect.
Avoid locations where humans or animals might accidentally touch fixture.

WARNING:

Never operate light without securing the lens door. When light is operating, the gas in the lamp inner arc tube
is at high pressure.
Never operate light if the fixture lens or outer glass envelope of the lamp is broken or missing.

WARNING:

ear safety glasses and gloves when handling lamp, High Pressure Sodium outer envelope is under vacuum

W
and could implode.

Electric shock hazard

Fire hazard

Explosion hazard

Explosion hazard

MOUNTING & WIRING

1. Screw the threaded mounting arm of the fixture into 1/2” NPS mounting hole on mounting device.
ighten locknut to secure fixture. See Figure 1.

T

Mounting
Arm Bolt

CAUTION:

Locknut

Mount the fixture so lamp is horizontal. (See Figure 2)

Lens
Door

Lampholder

Hinge

Figure 1

Clip

Figure 2

Install with lamp horizontal.

Reflector

2. Using provided twist on or other approved connectors, connect the fixture wires to the supply wires as follows:
See Figure 3)

(

a. Connect the black fixture wire marked 120V to the black (hot) supply wire.
b. Connect the white fixture wire marked COM to the white (neutral) supply wire.
c. Connect the bare copper (fixture ground) wire to the supply grounding wire.

X1

3

X

LAMP

IGN-01

20 V

1

COM

COM

X2

Figure 3

3. Make sure that all wires and connections are inside the mounting wiring compartment and that the cover is

properly sealed to keep moisture out. To weatherproof fixture, seal all holes in housing (mounting conduit, plugs,
photocontrols, etc.) with silicone sealant.

4. Release clip and swing hinged fixture lens door open. Screw lamp into socket in lampholder until finger-tight.

5. Close lens door and secure clip, making sure that gasket is in place and compressed to seal out moisture.

6. To operate, restore power to the circuit and switch light on.

AIMING FIXTURE

WARNING:

Do not turn mounting arm more than 360˚ after wires are connected. Excessive twisting of wires
may loosen connections.

1. Turn off power at circuit breaker or fuse box. Rotate mounting arm until light is pointing in the desired direction.

Tighten locknut to secure.

2. Loosen mounting arm bolt (do not remove) and tip fixture to desired angle. Retighten bolt to secure.

3. Turn power on and check aim. If adjustment is needed, turn power OFF at circuit breaker or fuse box and allow

fixture to cool before adjusting.

LAMP

1. T

2.

3.

4. Turn power back on.

5. Properly dispose of lamp per manufacturer’s recommendations.

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of
charge.
handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair
instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the finish on any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMA
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE,
STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage
prepaid to the authorized service center listed below
7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.

REPLACEMENT

urn off power at circuit breaker or fuse box. Allow fixture and lamp to cool.
Release retaining clip and swing hinged fixture lens door open. Remove old lamp and replace with new lamp of
correct type and wattage. Screw lamp into socket in lampholder until finger-tight.
Close lens door and secure clip, making sure that gasket is properly seated, free of debris, and compressed to seal
out moisture.

This warranty is extended to the original purchaser only and is not transferable.

TIC INCORPORA

ARE HEREBY

Electric shock hazard.

CAUTION:

TED WILL

MODIFIED

Use lamp of correct type and wattage as specified on fixture.

NOT BE LIABLE FOR INCIDENTALOR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD

This warranty is made by: Intermatic Incorporated/After Sales Service/7777 W

.

LIMITED 1 YEAR WARRANTY

This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in

, opened, taken apart or otherwise modified; (c) units not used in accordance with

inn Rd., Spring Grove, Illinois 60081-9698/815-675-

THESE INSTRUCTIONS DO NOT

COVER ALL VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR ALL SITUATIONS RELATED

TO FIXTURE INSTALLATION, OPERATION OR MAINTENANCE. FOR FURTHER INFORMATION CONTACT YOUR DISTRIBUTOR OR

INTERMATIC INCORPORATED - SPRING GROVE, ILLINOIS 60081 [phone] www.intermatic.com

158HL121

19