Receiver for AOE
POWER
NETWORK Ș
DC 12V , 500mA Ș
NETWORK
ON AIR
OPERATION
RECEIVER FOR AOE
RFA-101
DHCP
FACTORY RESET Ș
AUDIO OUTPUT
G
-
+
DHCP
STATIC
CONTACT OUTPUT
NO
NC
COM
1
2
3
4
5
RFA-101
Features
RFA-101 is an audio / data reception equipment
over a network (LAN / WAN).
This product is a receive-only device used for
AOE-212N that transmits AUDIO & DATA using
TCP/IP Ethernet Network.
- Transmission of AUDIO & DATA using TCP / IP
Ethernet Network
- Contact closure output available
It can receive the contact signal from the server
device (AOE-212N) and can work with the external device through the contact output.
Package and accessory includes
. DC 12V adapter × 1
1
2. 3P Terminal blocks × 2
3. Lan cable × 1
4. User guide × 1
Front panel
1. POWER LED (RED)
Power LED is displayed when power is supplied.
2. NETWORK LED (GREEN)
It is the LED that is displayed when sending data
through NETWORK. LED is blinking during normal
operation.
3. ON AIR LED (ORANGE)
This LED is displayed when streaming broadcast is
output. Even if the broadcast is not output because
buffering is in progress, the LED will be on.
4. OPERATION LED (GREEN)
CPU operation status is displayed. LED is blinking
during normal operation.
5. DHCP LED (ORANGE)
The LED lights up when the network IP setting is
DHCP. IP settings can be changed with the DHCP /
STATIC switch on the rear panel.
Receiver for AOE
COM NC NO
+ - G
G
+
G
+
+ - G
1
2
43
5 6
UTP
1 8
1
8
1
8
8
[ TOP VIEW ]
DIRECT
[
CABLE COLOR ORDER ]
CROSS
[
CABLE CROSS ORDER ]
[ FRONT VIEW ]
8.Brown
7.W/Brown
6
.Green
5
.W/Blue
4.Blue
3
.W/Green
3
.W/Green
2
.Orange
1.W/Orange
3
RFA-101
Rear panel
1. NETWORK PORT
This is network connection connector (RJ-45) which
supports 10/100 BASE-TX and receives streaming
broadcasts.
PIN NO. Function
1 TXN
2 TXP
3 RXN
4 NA
5 NA
6 RXP
7 NA
8 NA
Communication cable specifications
3. CONTACT OUTPUT
ontact output terminal. Please refer to below pin
C
pecifications of terminal.
s
4. AUDIO OUTPUT
This is the terminal (EURO) on which the streaming
broadcast is output. Please refer to below for necessary cable for terminal.
- BLANCED connection-
- UNBLANCED connection-
5. FACTORY RESET SWITCH
The product will be factory reset. Press and hold the
switch for about 5 seconds to reset the factory.
RFA-101 equipment is connected by CAT5 wire.
Dynamic IP (DHCP) or static IP (STATIC) switch to
IP SETTING SELECTION SWITCH (DHCP/STATIC)
2.
select. If you select static IP (STATIC), it will be selected by user's IP. (Initial value: 192.168.1.99)
Changing the switch (DHCP↔STATIC) automatically
reboots the device.
※ Note: When DHCP is selected as the switch, Dy-
namic IP (DHCP) operates even if static IP is set
on the web page.
6. DC 12V INPUT PORT
DC 12V power input terminal. Please use the included adapter.
Receiver for AOE
138.3
28.6
132.7
RJ45
DDR
MEMORY
eMMC
Audio
Codec
LDO
DCDC
CPU
PHY
RLY CTL
12VDC
Adapter
Audio Out
+
-
Network port
Factory Reset
DHCP/STATIC
switch
+10V
-10V
+5V
REG.
+5V
G
Contact Out
COM
N.O
N.C
Router or
Network switch
Control PC
RFA-101
POWERED SPEAKER
PA AMP
Network
(LAN/WAN)
Audio
Network
P
OWER
N
ETWORK
Ș
DC 12V , 500mA Ș
N
ETWORK
O
N AIR
OPERATION
RECEIVER FOR AOE
RFA-101
DHCP
FACTORY RESET Ș
AUDIO OUTPUT
G
-
+
DHCP
S
TATIC
CONTACT OUTPUT
NO
N
C
COM
RFA-101
Application
Specifications
FA-101
R
Data communication
Communication type NETWORK
Communication speed 10/100Mbps
Audio output characters
Output level @-10dBFs play 14dBu
/N
S
THD less than 0.1%
Operation temperature 0 ~ 40 ℃
ower Source
P
Power Consumption 3W
Weight(Set) 0.46kg/1.01lb
Dimensions(Set)
Design and specification are subject to be changed for the improvement of
*
138.3(W) x 132.7(H) x 28.6(D)mm
product quality without pre notice.
ore than 65dB
M
C 12V
D
.44(W) x 5.22(H) x 1.12(D)in
5
Block diagram
※ Dimensions
No. 141996 2017.6
Loading...