Interlogix TVB-5701, TVB-5702, TVB-5706, TVB-5707, TruVision TVB-5412 Installation Manual

TruVision

IP Thermal

Camera Installation

Guide

P/N 1073335-EN • REV A • ISS 28JUN17

Copyright © 2017 United Technologies Corporation,

Interlogix is part of UTC Climate, Controls &
Security, a unit of United Technologies
Corporation. All rights reserved.

Trademarks and

patents

Trade names used in this document may be

trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.

Manufacturer Interlogix

2955 Red Hill Avenue, Costa Mesa, CA

92626-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

FCC compliance Class A: This equipment has been tested and

found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the

equipment is operated in a commercial

environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful

interference to radio communications. Operation of

this equipment in a residential area is likely to

cause harmful interference in which case the user
will be required to correct the interference at his
own expense.

FCC conditions This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful

interference.

(2) This Device must accept any interference
received, including interference that may cause

undesired operation.

ACMA compliance Notice! This is a Class A product. In a domestic

environment this product may cause radio
interference in which case the user may be

required to take adequate measures.

Canada This Class A digital apparatus complies with CAN

ICES-003 (A)/NMB-3 (A).

Cet appareil numérique de la classe A est
conforme à la norme CAN ICES-003 (A)/NMB-3
(A).

European Union

directives

This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the EMC

Directive 2014/30/EU, the RoHS Directive
2011/65/EU.

2012/19/EU (WEEE directive): Products marked

with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your

local supplier upon the purchase of equivalent new

equipment, or dispose of it at designated collection

points. For more information see:

www.recyclethis.info.

2013/56/EU & 2006/66/EC (battery directive): This

product contains a battery that cannot be disposed

of as unsorted municipal waste in the European
Union. See the product documentation for specific
battery information. The battery is marked with this
symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier

or to a designated collection point. For more

information see: www.recyclethis.info.

Contact information

For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.

Installation Guide 1

Content

Introduction 2

Product overview 2

Installation 2

Installation environment 2
Package contents 3
Cable requirements 5
Camera description 6

Setting up the camera 6
Accessing the SD card 7
Mounting the IP thermal bullet camera 7

Using the camera with a TruVision recorder or another

system 8

Using the camera with TruVision Navigator 9

Specifications 9

TVB-5701 9
TVB-5702 10
TVB-5706 10
TVB-5707 11

Pin definitions 12

2 Installation Guide

Introduction

Product overview

This is the installation guide for TruVision IP thermal camera
models:

 TVB-5701 (IP Thermal Bullet Camera, 384x288, 15 mm)

 TVB-5702 (IP Thermal Bullet Camera, 384x288, 35 mm)

 TVB-5706 (IP Thermal Bullet Camera, 640x512, 15 mm)

 TVB-5707 (IP Thermal Bullet Camera, 640x512, 25 mm)

Installation

This section provides information on how to install the
cameras.

Installation environment

When installing your product, consider these factors:

• Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC UL listed Class 2 or CE certified
power supply to power the camera. Do not overload the
power cord or adapter.

• Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.

• Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
The operating temperature of the camera without heater