Interlogix TruVision TVB2406, TruVision TVB-4406 Installation Manual

P/N 1073163-EN • REV B • ISS 06DEC17

TruVision

High Resolution

TVI Bullet IR

Camera TVB-

2406/TVB

-4406 Installation

Guide

1

Contents

Overview ..................................................... 2

Description .................................................. 5

Installation ................................................... 7

Operating temperature range ..................... 10

Program .................................................... 11

Menu tree .................................................. 16

Specifications ............................................ 17

Legal ......................................................... 18

2

Overview

This is the TruVision High Resolution TVI Bullet IR
Camera Installation Guide for the camera model
TVB-2406/TVB-4406. This guide describes a
standard installation.

 TVB-4406 (TruVision HD-TVI Analog Bullet

Camera, 1080p, 5 to 50 mm Motorized VF
Lens, NTSC)

 TVB-2406 TruVision HD-TVI Analog Bullet

Camera, 1080p, 5 to 50 mm Motorized VF
Lens, PAL

Package contents

The camera consists of the following:

3

 Camera with power

and video output
cables

 4 screws and 4

anchors for wall or
ceiling installation

 Back box

 Screws M4.8 × 18,

4 pcs to attach the
back box

 Template

 Hex wrench

4

• CD

• Installation guide

• WEEE and battery

disposal

• Video test cable

5

Description

1. Power cable

2. 960H analog output (black)

3. TVI output (gray)

4. Mounting bracket

5. Camera body

6. Sun shield

7. Lens cover

8. Back box

8

6

Note:

When making adjustments to the VF lens bullet
camera, it is important to tighten the access cover
for the area that contains the video test cable
connector, OSD menu button, and the 960H
analog/WDR/TVI selection switch. The access
cover should be rotated until it is tight up against the
camera body.

Please check the camera output settings before
setting up a system. The TVI video output can only
be connected to a DVR with a TVI signal input. The
960H analog output supports the standard monitor
(or test monitor), an encoder, or a DVR.

The built-in switch is used to enable/disable the
WDR feature. When WDR feature is enabled, the
CVBS/960H analog output will be blocked out.

7

Video test cable
connector

OSD button

Switch
(Up =
CVBS/960H
analog
Down = WDR)

Installation

To install the camera

1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.

8

2. Following all local safety regulations, drill and
prepare the mounting holes.

3. As an optional step, install the back box on the
wall.

9

4. Route the cables to the cable hole and connect

the corresponding cables. Using a 75-ohm
coaxial video cable, connect the camera’s TVI
video output to a TVI DVR, and connect a
12 VDC or 24 VAC power supply to the power
cable.

5. Secure the camera to the ceiling or wall with
the enclosed screws.

10

6. Loosen the three screws and adjust the camera

according to the figure below to get an optimum
angle. Tighten the screw after completing the
adjustment.

7. Using the zoom and focus buttons on the PTZ
panel of the connected recorder, adjust the
camera’s zoom and focus.

Note: The camera has auto-focus capability. When
this feature is enabled, the camera can
automatically adjust itself to achieve the best focus.

Operating temperature range

The camera has a built-in heater that works within
the temperature range of -40 and +60 °C (-40 to
+140 °F). The heater only works at 24 VAC. The
heater is not for de-ice or defog purposes.

360°

90°

360°

11

You can configure the heater option in the OSD
menu under SET UP > SPECIAL > HEATCTRL.
There are three options:

Off: Heater is disabled.

Auto: The heater starts to work when the

temperature falls below -10 °C (14° F). When
temperature increases to -5 °C (23 °F), it will stop
working.

On: The heater is enabled until the temperature
reaches 40 °C (104 °F), when it is then
automatically disabled.

Program

Once the camera hardware has been installed, you
can then program the camera.

The camera has a built-in OSD button and supports
UTC (Up The Coax) control over both 960H analog
and TVI outputs.

12

Using the buttons

Please press the Menu button to call up the OSD
menu and select an OSD item.

Press the button up/down
to move the cursor up or
down to an OSD item.

Press the button left/right
to move the cursor left or
right to adjust the value of

a selected OSD item.

Using a TVI output

Programming over the camera’s TVI output can be
done via a TVI DVR.

Connect the TVI cable to the DVR, as shown below.

13

Figure 1: TVI cable connection

Access the PTZ menu of the connected DVR. Set
the TruVision-Coax protocol and use the PTZ
control panel to configure the camera.

Click Iris+ to access to the camera OSD menu and
select an OSD item.

Click the directional buttons UP or DOWN to move
the cursor up or down to an OSD item.

Click the directional buttons LEFT or RIGHT to
move cursor left or right to adjust the value of a
selected OSD item.

Note:

TVB-2406/TVB-4406 has an auto-focus motorized
lens. Please use the ZOOM and FOCUS buttons to
adjust its zoom and focus.

14

When the Auto-focus feature is enabled, the camera
can automatically adjust itself to achieve the best
focus.

For more details, refer to the TVI DVR user manual.

Using a CVBS output

A TVS-C200 (purchase separately) can be used to
program the camera over its CVBS output, not the
TVI video output.

Connect a monitor and the TVS-C200 controller (if
required) as shown below.

15

Figure 2: CVBS cable connections

Press the OK button of the TVS-C200 for a few
seconds until you see the OSD menu display on the
monitor. The OK button is also used for selecting an
OSD item.

Use the directional buttons to move the cursor and
adjust a value.

For more details, refer to the TVS-C200 user
manual.

16

Menu tree

17

Specifications

Power supply 12 VDC / 24 VAC

Current 12 VDC: 1.67 A max.

24VAC: 83 mA max.

Power
consumption

20 W max.

Temperature 24 VAC: -40 to +60 °C (-40 to

+140 °F) with heater on

12 VDC: -30 to +60 °C (-22 to
+40 °F)

Weight (net) 1.59 kg / 3.5 lb. (without back box)

1.805 kg / 3.98 lb. (with back box)

Dimensions

108.3 × 114.1 × 317.5 mm / 4.26 ×

4.5 × 12.5 in. (without back box）

108.3 × 114.1 × 353.5 mm / 4.26 ×

4.5 × 13.92 in. (with back box)

18

Legal

Copyright:

© 2017 United Technologies Corporation,
Interlogix is part of UTC Climate, Controls & Security, a unit of

United Technologies Corporation. All rights reserved.

Trademarks and patents:

Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.

Manufacturer:

Interlogix

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification:

FCC compliance: Class A

Class A: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
op

erated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause

19

harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.

ACMA compliance

Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.

Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme
NMB-0330 du Canada.

European Union directives:

12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares

that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.

2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.

20

Product warnings and disclaimers

THESE PRODUCTS ARE INTENDED FOR SALE TO, AND
INSTALLATION BY, AN EXPERIENCED SECURITY PROFESSIONAL. UTC
FIRE & SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY
PERSON OR ENTITY BUYING ITS PRODUCTS, INCLUDING ANY
“AUTHORIZED DEALER”, IS PROPERLY TRAINED OR EXPERIENCED
TO CORRECTLY INSTALL SECURITY RELATED PRODUCTS.

For more information on warranty disclaimers and product safety
information, please check
www.firesecurityproducts.com/policy/product-warning/ or scan
the following code:

Contact information and manuals :

For contact information go to: www.interlogix.com or
www.firesecurityproducts.com

To get translations for this and other product manuals go to:
www.firesecurityproducts.com