Interlogix TruVision TVB-2401, TruVision TVB-4401, TruVision TVB-2403, TruVision TVB-4403 Installation Manual

TruVision High Definition TVI Bullet Camera

Camera with power and

3 screws and 3 anchors

Template

Installation Guide

CD

3. Mounting base output

6. IR LED

(black)

5
6

4

2

1

3

7

8

6

2

1

3
4

5

Drill Template

Installation Guide

Product overview

This is the Installation Guide for TruVision High Definition TVI
Bullet Camera TVB-2401/TVB-4401 and TVB-2403/TVB-4403.

This guide describes a standard installation.

Package contents:



video output cables



for wall or ceiling

installation





• WEEE and Battery



Disposal

Camera description

TVB-2403/TVB-4403

1. WDR/CVBS switch cable

2. Power cable

3. TVI video output cable (grey)

4. CVBS video output cable

5. Mounting base

6. Sun shield

7. Lens

8. IR LED

Note:

Please check the camera output settings before setting up a
system. The TVI video output can be only connected to a DVR
with TVI signal input. The CVBS output supports the standard
monitor, test monitor, encoder and DVR.

For TVB-2403/TVB-4403, you can connect the white and black
line ends of the WDR switch cable to enable the Wide Dynamic
Range (WDR) function. The WDR function is disabled by
default. If WDR is enabled, the CVBS output will be blocked
out, and only TVI output is available.

TVB-2401/TVB-4401

1. TVI video output cable (grey)

2. Power cable

© 2015 United Technologies Corporation. All rights reserved. P/N 1072936-EN • REV A • ISS 26MAR15
Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved.

4. Sun shield

5. Lens

Installation

To install the camera on a ceiling:

1. Using the template, place it level against the mounting
surface and mark the position of the mounting holes.

2. Following all local codes, drill and prepare the mounting
holes.

3. Securely fasten the mount to the mounting surface with

the screws.

Power supply

Current

Power consumption

Weight

Dimensions

(Ø × L)

Manufacturer

FCC compliance

communications. Operation of this equipment in a

ACMA compliance

Canada

Certification

360°

90°

360°

4. Using a 75-ohm coaxial video cable, connect the camera
TVI video output and a TVI DVR, and connect a 12 VDC
power supply to the camera power cable.

5. Adjust the camera position and angle as required.

Specifications

12 VDC

TVB-2401/TVB-4401: Max.300mA

TVB-2403/TVB-4403:

Max. 330mA

TVB-2401/TVB-4401:

Max. 3.5 W

TVB-2403/TVB-4403:

Max.4 W

TVB-2401/TVB-4401: 0.64 lb. (291 g)

TVB-2403/TVB-4403: 0.68 lb. (309 g)

2.76 x 5.89 in. (70 x 149.5 mm)

Programming

Programming on TVI output:

Programming on TVI output is available for TVB-2403/TVB-
4403 only.

Once the camera hardware has been installed, you can
configure the camera settings on the TVI DVR.

Select PTZ protocol as TruVision Coax and click menu button
to call up the camera menu.

For more details, please see the TVI DVR user manual.

Programming on CVBS output:

Programming on CVBS output is available for TVB-2403/TVB­4403 only.

Programming on CVBS output, you need to connect a monitor
and a TVS-C200 controller (purchase separately) as following
system figure.

Setup menu

Regulatory information

Interlogix.

2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Class A: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instruction manual, may
cause harmful interference to radio

residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.

Notice! This is a Class A product. In a domestic

The TVS-C200 has one male BNC output and a female output.
Please connect the male output to camera’s CVBS output and
female output to a monitor.

2 / 3 P/N 1072936-EN • REV A • ISS 26MAR15

environment this product may cause radio
interference in which case the user may be
required to take adequate measures.

This Class A digital apparatus complies with
Canadian ICES-003.

Cet appareil numérique de la classe A est
conforme à la norme NMB-0330 du Canada.

N4131