Interlogix TruVision Series, TVP-5201 Installation Manual

TruVision Stainless Steel
PTZ Camera Installation
Guide

P/N 1073420-EN • REV A • ISS 30JAN18

Copyright

© 2018 United Technologies Corporation,

Interlogix is part of UTC Climate, Controls & Security, a unit of
United Technologies Corporation. All rights reserved.

Trademarks

and patents

Trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the
respective products.

Manufacturer

Interlogix

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

FCC

compliance

Class A: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.

FCC

conditions

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:
(1) This device may not cause harmful interference.

(2) This Device must accept any interference received, including

interference that may cause undesired operation.

ACMA

compliance

Notice! This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may
be required to take adequate measures.

Canada

This Class A digital apparatus complies with CAN ICES-003

(A)/NMB-3 (A). Cet appareil numérique de la classe A est
conforme à la norme CAN ICES-003 (A)/NMB-3 (A).

European

Union

directives

This product and - if applicable - the supplied accessories too are

marked with "CE" and comply therefore with the applicable

harmonized European standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info.

Product

warnings

and

disclaimers

THESE PRODUCTS ARE INTENDED FOR SALE TO, AND

INSTALLATION BY, AN EXPERIENCED SECURITY
PROFESSIONAL. UTC FIRE & SECURITY CANNOT PROVIDE
ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING
ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”, IS
PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY
INSTALL SECURITY RELATED PRODUCTS.

For more information on warranty disclaimers and product safety
information, please check
www.firesecurityproducts.com/policy/product-warning/ or scan the
following code:

Contact

information

and manuals

For contact information go to: www.interlogix.com or

www.firesecurityproducts.com
To get translations for this and other product manuals go to:

www.firesecurityproducts.com

Content

Introduction 6

Product overview 6

Installation 6

Installation environment 6
Package contents 7
Camera description 10
Alarm input and output connections 11

SD memory card installation 11
Mounting the PTZ dome camera 12
Mounting the junction box 13

Using the camera with an Interlogix NVR or Hybrid DVR or

another system 15

Using the camera with TruVision Navigator 16

Access the camera over the internet 16

Specifications 19

PTZ camera 19
PTZ camera junction box 19

Pin definitions 20

Installation Guide 5

Introduction

Product overview

This is the installation guide for the TruVision Stainless Steel
PTZ dome camera model:

• TVP-5201 (2MPX wall-mount PTZ dome camera, 23X)

Installation

This section provides information on how to install the
cameras.

Installation environment

When installing your product, consider these factors:

• Electrical: Install electrical wiring carefully. It should be

done by qualified service personnel. Always use a proper
PoE switch or a 24 VDC UL listed Class 2 or CE certified
power supply to power the camera. Do not overload the
power cord or adapter.

• Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.

• Temperature: Do not operate the camera beyond the
specified temperature, humidity, or power source ratings.
The operating temperature of the camera is between -40
to 60°C (-40 to140°F). Humidity is below 90%.

• Moisture: Do not expose the camera to rain or moisture
or try to operate it in wet areas. Turn the power off
immediately if the camera is wet and ask a qualified

6 Installation Guide

service person for servicing. Moisture can damage the

camera and also create the danger of electric shock.

• Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.

• Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.

Package contents

Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.

Package contents include the following:

Camera

Installation manual

Installation Guide 7

CD with configuration manual
and TruVision Device
Manager

Equipment disposal sheet

Battery disposal sheet

Hex wrench

Junction box

Screw A (10 pcs.)

13.6 mm

(0.54 in.)

1.6 mm

(0.06 in.)

5.85 mm

(0.23 in.)

5.5 mm

(0.22 in.)

5.0 mm

(0.20 in.)

10.7 mm (0.42 in.)

Screw B (4 pcs.)

25 mm

(0.98 in.)

5.4 mm

(0.21 in.)

13 mm

(0.51 in.)

16 mm (0.63 in.)

Blue sealing plug (3 pcs.)

6 mm (0.24 in.)

23.5 mm

(0.93 in.)

20.5 mm (0.81 in.)

A-A

A

A

6 mm (0.24 in.)

8 mm (0.31 in.)

8 Installation Guide

White sealing plug (3 pcs)

A-A

A

A

23.5 mm

(0.93 in.)

6 mm (0.24 in.)

20.5 mm (0.81 in.)

8 mm (0.31 in.)

10 mm (0.39 in.)

Black sealing plug (3 pcs)

A-A

A

A

23.5 mm

(0.93 in.)

20.5 mm (0.81 in.)

6 mm (0.24 in.)

11 mm (0.43 in.)

13 mm (0.51 in.)

Drill template – junction box

328 mm (12.91 in.)

113 mm (4.45 in.)

CAUTION: Use direct plug-in UL listed power supplies
marked Class 2/CE certified or LPS (limited power source) of
the required output rating as listed on the unit.

Installation Guide 9

Camera description

Figure 1: PTZ camera description and connectors

VI

EOD

1200 mm (47.24 in.)

250 mm (9.84 in.)

①
②

③

④

⑤
⑥

⑦

1. 24V power supply (red 24 VAC,
yellow_green ground, black 24
VAC)

2. RS-485 (Orange RS-485+,
Yellow RS-485-)

3. Audio in (red_white) / Audio
output (blue_white)

4. Alarm inputs (green, blue,
purple, gray, white,
black_white, brown_white) /
two alarm outputs (red, pink)

5. 960H analog output

6. RJ45 network cable

7. Safety lanyard

10 Installation Guide

Alarm input and output connections

The alarm output can be used to turn on and off an external

alarm device. Connect a 30 VDC/1A external power supply to

the alarm output. If using an AC power supply, an external
relay must be used to prevent electric shock and damage to
the device. See Figure 2 below.

Figure 2: External alarm output

SD memory card installation

To install the SD memory card in the PTZ dome

1. Loosen the six hex screws on the bubble assembly.

Note: Do not remove the hex screws from the bubble

assembly. Loosen them enough to remove the bubble.

2. Carefully pull down the bubble assembly (2) to separate it
from the top enclosure (1), and remove the thin foam
shipping ring (3), and tape (4).

Installation Guide 11

①

②

③

④

Note: Remove the thin foam shipping ring prior to

completing the installation.

3. Optional: Insert the memory card into the SD card slot (1)
until it clicks into place.

4. Reinstall the bubble assembly on the camera housing.

Mounting the PTZ dome camera

The TruVision Stainless Steel PTZ Wall Bracket (TVP-WBS,
not included) is required to wall-mount the PTZ camera, and
the TruVision Stainless Steel Pendant Bracket (TVP-PAS, not
included) is required to mount the PTZ camera to a ceiling.

12 Installation Guide

Refer to the installation guides provided with the TVP-WBS
and TVP-PAS mounting kits for instructions on mounting the
stainless steel PTZ camera to the wall or ceiling.

After completing the PTZ camera installation, you can remove
the safety lanyard handle. See the image below.

Mounting the junction box

To mount the PTZ camera junction box:

1. Drill mounting holes in the mounting surface according to
the supplied drill template. Insert the four screw Bs in the
mounting surface, and partially tighten down the four
mounting screws.

328 mm (12.91 in.)

113 mm (4.45 in.)

2. Remove the cover of the junction box and align the four
slotted mounting holes on the junction box with the
mounting hardware. Secure the junction box to the
mounting surface.

Installation Guide 13

3. Route the camera cable harness through the cable
access hole on the junction box and tighten the
waterproof nut.

Note: Insert the PoE cable or BNC cable first, followed by
the RS-485 wires, audio input and output wires, alarm
input and output wires, and power supply wires. For the
power supply wires, the red plastic interface must first be
removed.

4. If the other three cable access holes are used, unscrew
the hex bolt and remove the pre-installed black solid
sealing plug.

5. Choose the applicable sealing plug from the white, blue,
and black sealing plugs according to the diameter of the
cable.

6. Route the cable through the sealing plug (1), flat washer
(2) and the hex bolt (3) and tighten to maintain IP67

rating.

14 Installation Guide

7. Connect the wires inside the junction box and attach the
cover of the junction box with the screw As.

Using the camera with an Interlogix NVR
or Hybrid DVR or another system

Please refer to the NVR/DVR user manuals for instructions on
connecting and operating the camera with these systems.

Installation Guide 15

Using the camera with TruVision
Navigator

The camera can be connected to an Interlogix NVR, hybrid
DVR, or directly to TruVision Navigator. Please refer to the
user manual of TruVision Navigator and/or of the NVR or
hybrid DVR for instructions.

Access the camera over the
internet

Use the web browser to access and control the camera over
the internet.

Note: Any changes made to the camera’s configuration only
apply to this camera. Only authorized users should be able to
modify camera settings.

When you first start up the camera, the Activation window
appears. You must define a high-security admin password

before accessing the camera. There is no default password
provided.

You can activate a password via a web browser and via
TruVision Device Manager (included on the CD to find the IP

address of the camera).

To activate the camera via the web browser:

1. Power on the camera and connect the camera to the
network.

2. Type the IP address into the address bar of the web
browser and press Enter to enter the activation interface.

16 Installation Guide

Note:

• The default IP address of the camera is

192.168.1.70.

• For the camera to enable DHCP by default, you

must activate the camera via TruVision Device
Manager. Please refer to the following section, “To

activate the camera via TruVision Device Manager.”

3. Type the password in the Password field.

Note: A valid password range must be between 8 and 16

characters. You can use a combination of numbers, lower

and upper case letters, and special characters : _ - , . * &
@ / $ ? Space. The password must contain characters

from at least two of these groups. We also recommend

that you reset your password regularly. For high security
systems, it is particularly recommended to reset the
password monthly or weekly for better protection.

4. Confirm the password.

5. Click OK to save the password and enter the live view
interface.

Installation Guide 17

6. Click the Configuration tab on the top of the screen and
select the parameter to change.

Figure 3: Example of a configuration window

To activate the camera via TruVision Device Manager:

For instructions on how to activate the camera using TruVision

Device Manager, refer to the TruVision Device Manager User
Manual. Go to www.interlogix.com/video/product/truvision-

device-manager and click Downloads.

18 Installation Guide

Specifications

PTZ camera

Electrical

Voltage input

24 VAC, Hi-PoE

Power consumption

Max. 60 W

Miscellaneous

Connectors

24 VAC, Alarm In/Out, RS-485,

Ethernet RJ45 connector, Audio

in/output, CVBS (960H) Output

Operating temperature

-40 to +65°C (-40 to +149°F)

Dimensions

262 × 330 mm (10.3 × 13.0 in.)

Weight

10 kg (22 lb.)

Environmental rating

IP67, IK10

PTZ camera junction box

Dimensions

364 × 256 × 111.5 mm

(14.33 × 10.08 × 4.39 in.)

Weight

4.8 kg (10.58 Ib.)

Installation Guide 19

Pin definitions

There are eight wires on a standard UTP/STP cable and each
wire is color-coded. The following shows the pin allocation and
color of straight and crossover cable connection:

Figure 4: Straight-through cable

1 White/Orange

White/Orange 1

2 Orange Orange 2

3 White-Green White-Green 3

4 Blue Blue 4

5 White/Blue White/Blue 5

6 Green Green 6

7 White/Brown White/Brown 7

8 Brown Brown 8

Figure 5: Cross-over cable

1 White/Orange

White/Orange 1

2 Orange Orange 2

3 White-Green White-Green 3

4 Blue Blue 4

5 White/Blue White/Blue 5

6 Green Green 6

7 White/Brown White/Brown 7

8 Brown Brown 8

Please make sure your connected cables have the same pin
assignment and color as above before deploying the cables in
your network.

20 Installation Guide