Page 1
IFS POE302-EX User Manual
P/N 1072690 • REV B • ISS 11JUL14
Page 2
r
A
Copyright © 2014 United Technologies Corporation
Interlogix is part of UTC Building & Industrial Systems, a unit of United
Technologies Corporation. All rights reserved.
Trademarks and
patents
The IFS POE302-EX name and logo are trademarks of United Technologies.
Other trade names used in this document may be trademarks or registered
trademarks of the manufacturers or vendors of the respective products.
Manufacture
Interlogix
3211 Progress Drive, Lincolnton, NC 28092 USA
Authorized EU manufacturing representative:
UTC Climate Controls & Security B.V.,
Kelvinstraat 7, 6003 DH Weert, Netherlands
Intended use Use this product only for the purpose it was designed for; refer to the data sheet
and user documentation for details. For the latest product information, contact
your local supplier or visit us online at www.interlogix.com.
Certification
N4131
FCC compliance This equipment has been tested and found to comply with the limits for a Class
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications.
You are cautioned that any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate the
equipment.
ACMA compliance Notice! This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may b e required to take adequate
measures.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme á la norme NMB-003du
Canada.
European Union
directives
2004/108/EC (EMC Directive): Hereby, UTC Building & Industrial Systems, Inc.
declares that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.
Contact Information For contact information, see www.interlogix.com
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu
www.utcfssecurityproducts.eu
.
.
or
Page 3
IFS POE302-EX User Manual
TABLE OF CONTENTS
IFS POE302-EX USER MANUAL ....................................................................................1
INTRODUCTION
1.1 Package Contents................................................................................................................................4
1.2 Key Features.........................................................................................................................................4
1.3 Technical Specification.......................................................................................................................5
..............................................................................................................4
HARDWARE DESCRIPTION...........................................................................................7
2.1 Product Outlook...................................................................................................................................7
2.2 Ports Connection.................................................................................................................................8
2.3 LED Definition:.....................................................................................................................................8
HARDWARE INSTALLATION .........................................................................................9
3.1 Before Installation................................................................................................................................9
3.2 Connect POE302-EX to the Power Source Equipment (PSE)..........................................................9
3.3 Connect POE302-EX to the Powered Device (PD)......................................................................... 10
3.4 Multiple PoE Extender Installation.................................................................................................. 10
CONTACTING TECHNICAL SUPPORT........................................................................12
3
Page 4
IFS POE302-EX User Manual
Introduction
1.1 Package Contents
Thank you for purchasing the IFS POE302-EX IEEE 802.3at Power over Gigabit Ethernet Extender, your Power over Gigabit
Ethernet Extender package contains the following contents:
Check the contents of your package for following parts:
IEEE 802.3at Power over Gigabit Ethernet Extender x1
User's Manual x1
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including
the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
1.2 Key Features
IEEE 802.3at / 802.3af Power over Ethernet compliant
Complies with IEEE 802.3 / 802.3u / 802.3ab 10/100/1000Base-T
Extends the range of PoE an additional 100 meters (328ft.)
Auto-detect and protect of PoE equipment from being damaged by incorrect installation
Multiple units, daisy-chain installation support
Forwards both Ethernet data and PoE power to remote device
No external power cable installation required
Compact size, Wall-mountable design
Plug-and-Play installation
4
Page 5
1.3 Technical Specification
Model POE302-EX
Interfaces
1 x 10/100/1000Base-T Ethernet with IEEE 802.3at / 802.3af PoE
LAN IN
LAN OUT
Power over Ethernet
PoE Standard
PoE Power Supply Type Mid-Span / Type B
PoE Power Output 52V DC, 510mA, Max. 26 Watts
Power Pin Assignment 4/5(+), 7/8(-)
“Data + DC” in
Auto MDI/MDI-X, Auto-negotiation RJ-45 connector
1 x 10/100/1000Base-T Ethernet with IEEE 802.3at / 802.3af PoE
“Data + DC” out
Auto MDI/MDI-X, Auto-negotiation RJ-45 connector
IEEE 802.3af (Power over Ethernet)
IEEE 802.3at (High Power over Ethernet Pre-Standard)
IFS POE302-EX User Manual
Maximum Distance
Hardware Specification
Data Rate 10/100/1000Mbps
Switch Architecture Store-and-Forward
Switch Throughput
Maximum Frame Size 1552Bytes
Flow Control
LED Indicators
Protection
Dimension (W x D x H) 94 x 70 x 26 mm
Weight 197g
Power Requirement IEEE 802.3at compliant with voltage within 52V-56V DC
Power Consumption 3.2 Watts (system maximum)
Mechanical Metal / Wall Mountable / Optional kit for Din-Rail Mount
3 units, daisy-chain installatio n with 500m support
10Mbps:14880pps@64Bytes
100Mbps:148810pps@64Bytes
1000Mbps:1488000pps@64Bytes
Back pressure for Half-Duplex
IEEE 802.3x Pause Frame for Full-Duplex
1x PoE IN (Green)
1 x LAN Data (Green)
1 x PoE OUT (Green)
ESD(Ethernet): 2KV(TBD)
Surge (EFT for power) : 2KV(TBD)
10Base-T: 4-Pair UTP Cat. 5 up to 100m (328ft)
Network Cable
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standard Compliance
100Base-TX: 4-Pair UTP Cat. 5 up to 100m (328ft)
1000Base-T: 4-Pair UTP Cat. 5e, 6, up to 100m (328ft)
EIA/TIA-568 100-ohm STP (100m, 328ft)
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet (Pre-standard)
IEEE 802.3x Flow Control
5
Page 6
Environment
Operating
IFS POE302-EX User Manual
Temperature: -10 ~ 60 Degree C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage
Distance will often be shorter due to power delivery voltage-drop on th e wire. T he maximu m distances will
vary on the quality of the UTP cable and environment.
Temperature: -40 ~ 85 Degree C
Relative Humidity: 5 ~ 95% (non-condensing)
6
Page 7
Hardware Description
2.1 Product Outlook
IFS POE302-EX User Manual
7
Page 8
2.2 Ports Connection
Connect the PoE IN port from following 802.3at / 802.3af PSE device through a
CAT-5/5e/6 UTP cable:
IN Port
OUT Port
PoE injector
PoE Injector Hub
PoE Ethernet Switch
Previous POE302-EX
Connect the PoE OUT port to following 802.3at / 802.3af PD device through a
CAT-5/5e/6 UTP cable:
PoE IP Camera
PoE VoIP Phone
PoE Wireless AP
PoE Splitter
Next POE302-EX
IFS POE302-EX User Manual
2.3 LED Definition:
LED Color Function
PoE IN Green Lights to indicate the port is providing 52-56V (802.3at) / 48V (802.3af) DC in-line
power.
LNK/ACT Green Lights to indicate the port is link up.
Blink: indicate that the extender is actively sending or receiving data over IN port.
PoE OUT Green Lights to indicate the port is providing 52-56V (802.3at) / 48V (802.3af) DC in-line
power.
8
Page 9
IFS POE302-EX User Manual
Hardware Installation
This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same device and automatically
distinguishes the speed of incoming connection.
This section describes the hardware features of POE302-EX. Before connecting any network device to the POE302-EX, re ad
this chapter carefully.
3.1 Before Installation
Before your installation, it is recommended to check your network environment. If there is any far away IEEE 802.3at / 802.3af
devices need to power on, the POE302-EX can provide you a way to supply power for this Ethernet device conveni ently and
easily.
The POE302-EX is installed between the PSE (Power Source Equipment) and the PD (Powered Device); it is powered by PSE
and forwards the Ethernet data and remaining POE power to the PD. The POE302-EX doesn’t require an external power
supply and it can be installed easily just plug and play; that means the operator do es not need to configure the POE302-EX.
The POE302-EX injects power to the PDs without affecting the data transmission performance. It offers a cost effective and
quick solution to extend power and data an additional 100m.
1. To provide you better PoE power and data extension quality, we strongly recommend that you use
“Solid UTP Cable” when installing POE302-EX.
2. The POE302-EX can be installed with third-party device if the device complied with IEEE 802.3at /
802.3af standard.
3.2 Connect POE302-EX to the Power Source Equipment (PSE)
There are 2 RJ-45 ports in the PoE Extender, of which the “IN” port functions as "PoE (Data and Power) input" and
the ”OUT” port on the other side functions as "PoE (Data and Power) output".
Step 1: Connect a standard Cat.5/5e/6 UTP cable from Power Source Equipment (PSE), such as PoE Switch, PoE Injector
hub and single port PoE injector, to the “IN” port of POE302-EX.
Step 2: The PSE delivers both Ethernet Data and PoE power over UTP cable to the POE302-EX and the “PoE IN” LED will be
steady on.
1. T he POE IN LED turn on steady green means POE302-EX is being powered successfully with PoE
class 0.
2. If POE IN LED does not turn on, please check the remote PSE or the cable with a PC or a network
device to see if the cable is correct. Or with an IEEE 802.3at / 802.3af device such as the target PD to
check the power injection is correct either.
9
Page 10
IFS POE302-EX User Manual
3.3 Connect POE302-EX to the Powered Device (PD)
Step 3: Connect the additional Cat.5/5e/6 cable that will be used to connect to the remote Powered Device (PD) to the “OUT”
port of POE302-EX.
Step 4: The "OUT" port is also the power injectors which transmit DC Voltage to the Cat.5/5e/6 cable and transfer data and
power simultaneously between the PSE and PD.
Step 5: Once POE302-EX detects the existence of an IEEE 802.3at / 802.3af device, the “PoE OUT” LED indicator will be
steady, ON to shows it is providing power.
1. If the connected device is not fully complying with IEEE 802.3at / 802.3af standard or in-line power
device, the PoE OUT LED indicator of POE302-EX will not be steady on.
2. According to IEEE 802.3at / 802.3af standard, the POE302-EX will not inject power to the cable if not
connecting to a standard IEEE 802.3at / 802.3af device.
3.4 Multiple PoE Extender Installation
The POE302-EX PoE Extender supports multiple units, daisy-chain installation. They can be employed in series for even longer
distances based on remote PoE IP Camera or PoE Wireless Access Point power requirement.
Step 1: Connect the additional Cat.5/5e/6 cable from the “OUT” port of the first POE302-EX, the other end of the UTP cable be
used to connect to the “IN” port of remote / next POE302-EX.
Step 2: The “PoE OUT” LED indicator of the first POE302-EX will be steady to shows it is providing power to next PoE
Extender.
Step 3: The “PoE IN” LED on the next POE302-EX will steady on.
Step 4: Connect the additional Cat.5/5e/6 cable to the remote PoE powered device to the “OUT” port of next or third
POE302-EX.
10
Page 11
IFS POE302-EX User Manual
1. Per POE302-EX will take 3.2 Watts maximum for the system itself, please check the total power
consumption of your IEEE 802.3at / 802.3af PD and the POE302-EX before you make the daisy-chain
connection. If the overall power consumption is overloaded, the local PSE could shutdown the whole
power system.
2. Per POE302-EX cable segment is limited in 100 meters Cat.5/5e/6 UTP wire from its IN/OUT port to
the other data end, use of any other non standard cable or over distance could results in unstable
connection.
11
Page 12
IFS POE302-EX User Manual
Contacting Technical Support
Contact technical support if you encounter any difficulties during this installation. Please make sure you
have the requested diagnostic or log files ready before you contact us by phone or go to
www.interlogix.com/customer-support
Technical Support
Europe, Middle East and Africa
W Select Contact Us at www.utcfssecurityproducts.eu
North America
T +1 855.286.8889
E techsupport@interlogix.com
Australia
E techsupport@interlogix.au
.
12
Loading...