IFS POE201-EX POE Extender
User Manual
P/N 1076526 • REV A • ISS 08FEB12
Copyright © 2012 UTC Fire & Security Company. All rights
r
reserved.
Trademarks and
patents
Interlogix, IFS POE201-EX POE Extender, the IFS
Brand and logo are trademarks of
UTC Fire & Security.
Other trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacture
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA
92626-5923, USA
Version This document applies to IFS POE201-EX POE
Extender version 1.0.
Certification
N4131
FCC compliance Class A: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
ACMA
compliance
European Union
directives
Notice! This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
2004/108/EC (EMC directive): Hereby, UTC Fire
& Security declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Contact
information
Customer support
www.utcfireandsecurity.com or
www.interlogix.com
www.interlogix.com/customer-support
Contents
Package Contents 1
Product Features 1
Product Overview 2
Port Connections 3
In Port 3
Out Port 3
LED Indicators 3
Hardware Installation 4
Before Installation 4
Power Source Equipment (PSE) Installation 4
Powered Device (PD) Installation 5
Multiple PoE Extender Installation 6
Specifications 8
Contacting Technical Support 9
IFS POE201-EX POE Extender User Manual i
Package Contents
Thank you for purchasing the IFS POE201-EX IEEE 802.3af
High Power over Fast Ethernet Extender.
Open the package containing the IFS POE201-EX and
carefully unpack it. The box should contain the following items:
● POE201-EX x1
● User Manual x1
If any of these items are missing or damaged, please contact
your dealer immediately. If possible, retain the product box
including the original packing material to return it to for
repair/replacement.
Product Features
• Complies with IEEE 802.3af Power over Ethernet
• Extends the range of PoE an additional 100 meters (328ft.)
• Forwards both Ethernet data and PoE power to a remote
device
• Auto-detection of POE IEEE 802.3at equipment and
devices to prevent damage caused by incorrect installation.
• Multiple units can be daisy-chained for extended distance
(max. 3 units)
• No external power required
• Compact size, Wall-mountable design
• Plug-and-Play installation
IFS POE201-EX POE Extender User Manual 1
Product Overview
Figure 1 shows the front and side panels of the POE201-EX.
Figure 1: POE201-EX Front and Side Panels
2 IFS POE201-EX POE Extender User Manual
Port Connections
In Port
Connect the PoE IN port from following 802.3af PSE type
devices through a CAT-5e/6 UTP cable:
• PoE injector
• PoE Injector Hub
• PoE Ethernet Switch
• Another POE201-EX
Out Port
Connect the PoE OUT port to following 802.3af PD type
devices through a CAT-5e/6 UTP cable:
• PoE IP Camera
• PoE VoIP Phone
• PoE Wireless AP
• PoE Splitter
• Another POE201-EX
LED Indicators
POE201-EX LED indicators
LED Color Function
PoE IN Green
LNK/ACT Green
Blink
PoE OUT Green
IFS POE201-EX POE Extender User Manual 3
Lights to indicate that the port is receiving
power.
Lights to indicate the port is link up.
Blink: Indicates the data activity through device.
Lights to indicate that the device is providing
power.
Hardware Installation
The POE201-EX operates at two different data rates – 10Mbps
and100Mbps in the same device and automatically adjusts
based on the speed of incoming connection.
The following section describes the hardware features of the
POE201-EX. Carefully read this section before connecting any
network device to this unit.
Before Installation
It is recommended to check the network environment before
the installation. The POE201-EX conveniently extends the
distances in an installation base by transferring power to the
remote PDs. (Powered Devices).
The POE201-EX is installed between the PSE (Power Source
Equipment) and the PD (Powered Device); it is powered by
PSE and forwards the Ethernet data and remaining POE
power to the PD. The POE201-EX doesn’t require an external
power supply and it can be installed easily just plug and play;
that means the operator does not need to configure the
POE201-EX. The POE201-EX injects power to the PDs
without affecting the data transmission performance. It offers a
cost effective and quick solution to extend power and data for
an additional 328 ft. (100m).
Note: The POE201-EX can be installed with third-party
devices as long as the connected device complies with the
IEEE 802.3af standard.
Power Source Equipment (PSE) Installation
1. Connect a standard Cat5e/6 UTP cable from Power Source
Equipment (PSE), such as PoE Switch, PoE Injector hub or
a single port PoE injector, to the “IN” port of POE201-EX.
4 IFS POE201-EX POE Extender User Manual
2. The PSE delivers both Ethernet Data and PoE power over
the UTP cable to the POE201-EX and the “PoE IN” LED
will be illuminated.
Note: The POE IN LED illuminates in a steady state to
indicate that it is receiving power.
If the POE IN LED does not turn on, please check the remote
PSE and/or the cable with a PC or a network device to see if
the cable is correct
Powered Device (PD) Installation
1. Connect one side of the CAT5e/6 cable to the "OUT" port
of the POE201-EX, and the other side to the PD.
2. The "OUT" port injects power and transfers data to the PD.
3. Once the PD is detected, the “PoE OUT” LED indicator will
illuminate in a steady state showing that it is providing
power.
Figure 2: Extender connection diagram
Note: The POE201-EX will not inject power to a PD that
doesn't comply to the IEEE 802.3af standard. Therefore, in this
type of connection, the PoE Out LED will not illuminate.
IFS POE201-EX POE Extender User Manual 5
Multiple PoE Extender Installation
The POE201-EX PoE Extender supports daisy-chain
installation of multiple units Based on the power requirements
of the PD, multiple POE201-EX devices can be used to
increase the installation distance.
1. Connect one end of the CAT5e/6 cable to the "OUT port of
the first POE201-EX and the other end to the "IN" port of
the next POE201-EX.
2. The “PoE OUT” LED indicator of the first POE201-EX will
illuminate in a steady state indicating that it is providing
power to next PoE Extender.
3. The “PoE IN” LED on the next POE201-EX will illuminate
steadily to indicate that it receives the power from the
previous PoE Extender.
4. Connect one side of the CAT5e/6 cable to the "OUT" port
of the POE201-EX, and the other side to the PD.
6 IFS POE201-EX POE Extender User Manual
Figure 3: Multiple Extenders connection diagram
Note: Each POE201-EX device will consume a maximum of 2
watts of the total overall PoE budget for itself. It is
recommended to check the power requirements of the 802.3af
PD and the POE201-EX in your system daisy-chain design
before installation. If the overall power consumption is
overloaded, the local PSE could shutdown the whole PoE
power supplied by that port on the PSE.
Each connection between POE201-EX devices is limited of up
to 328 ft. (100m) with CAT5e/6 cable. Use of any other cable
may result in an unstable connection.
IFS POE201-EX POE Extender User Manual 7
Specifications
Ethernet
Data Rate 10/100Mbps
Throughput (packet per second) 148810pps@64Bytes
IEEE Standards
Latency
Maximum Frame Size
EIA/TIA 568 Standards
Power Over Ethernet (PoE)
PoE Standard IEEE 802.3af Power over Ethernet PSE / Mid-Span
PoE Power Supply Type Mid-Span / Type B (no external adapter required)
PoE Output Pin Assignment 4/5(+), 7/8(-)
PoE Output Power
with multiple extenders
Connectors & Indicators
Ethernet + PoE In 1 x RJ-45 connector (10/100Base-TX & 802.3af PD Mid-Span)
Ethernet + PoE Out 1 x RJ-45 connector (10/100Base TX & 802.3af PSE Mid-Span)
LED Indicator 1-PoE In, 1 PoE Out, 1 Data LNK/ACT
Electrical and Mechanical
Input Power
PoE Output Power 48VDC @ 270mA, 13 watts
Maximum Powered Devices 1
Enclosure Metal
Dimensions (H x W x D) 3.7 x 2.75 x 1.0 in.; (95 x 70 x 25mm)
Weight 0.47 lbs. / 215g
Environmental
MTBF >50,000 hrs. @ 25°C
Operating Temperature 0ºC~50ºC
Storage Temperature -10ºC~70ºC
Relative Humidity 5%–90% (non-condensing)
8 IFS POE201-EX POE Extender User Manual
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3x Flow Control
7.840µs
1552 Bytes
Category 5/5e cable
IEEE 802.2af Power over Ethernet PD / Mid-Span
Class 1 (3.8 watts) 300m (984 ft.)
Class 2 (6.5 watts) 300m (984 ft.)
Class 3 (12.9 watts) 200m (656 ft.)
Non-PoE (Data Only) 300m (984 ft.)
Powered by 48VDC from PoE switch or Mid-Span Injector @ IEEE
802.3af
Contacting Technical Support
Contact technical support if you encounter any difficulties
during this installation. Please make sure you have the
requested diagnostic or log files ready before you contact us
by phone or go to www.interlogix.com/customer-support.
Technical Support
Europe, Middle East and Africa
W Select Contact Us at www.utcfssecurityproducts.eu
North America
T +1 855.286.8889
E techsupport@interlogix.com
Australia
E techsupport@interlogix.au
IFS POE201-EX POE Extender User Manual 9
Loading...