Interlogix 600-1046-95 Installation Instructions Manual

OEM Transceiver Module with Crystal
Transmitter Installation Instructions

Introduction

The OEM transceiver modules are compatible with Interlogix
wireless transmitters and receivers. The modules have an
onboard receiver and transmitter, microprocessor, and
connection for a daughter board. The microprocessor controls
the receiver and transmitter, providing antenna switching and
AGC functions. It also analyzes the data from the receiver,
validates incoming packets, and returns packets to the
controlling device when polled. A daughter board, which
communicates with the module via an 8-pin header, can be
added to implement a variety of functions.

Each module encapsulates the receiver and transmitter
functions and formats and presents a common interface to the
daughter board. Therefore, even though protocols vary among
the Interlogix radio frequencies used around the world, the
interface is the same to the daughter board.

Installation guidelines

Observe the following guidelines when installing the OEM
transceiver module:

• Allow at least 9 inches (22.9 cm) of clearance above the
enclosure for the antennas.

• Avoid mounting locations that expose the module to
moisture.

• Avoid areas with excessive metal or electrical wiring
including furnace and utility rooms. If unavoidable, mount
on or near metal with the antenna extending above the
metallic surfaces as shown in Figure 1

.

• While a transmitter may have an open-air range of 1000 ft.
(300 m) or more, the installation site can have a significant
effect on the transmitter range. Changing the sensor
location may help overcome adverse wireless conditions.

Installation

600-1029 enclosure

To mount the 600-1029 enclosure, follow the installation
instructions provided with the enclosure.

600-0131 daughter board

T

o attach the 600-0131 daughter board, follow the installation

instructions provided with the daughter board.

600-1046-95 OEM transceiver module

To mount the OEM transceiver module onto the back plate of
the 600-1029 enclosure, do the following:

1. Insert the antennas into the antenna shrouds (Figure 2

Caution: You must be free of static electricity before handling

circuit boards. Wear a grounding strap or touch a bare metal
surface to discharge static electricity.

2. Gently slide the top of the circuit board under the two top
latches.

3. Snap the circuit board in at the bottom latch to secure it in
place as shown in Figure 2

.

).

Figure 1. Mounting on or near metal

METAL

P/N 466-2236 • REV C • January 2011 1

METAL

2. Installing the circuit board

ON

123 45678

Figure

Antenna shrouds

Current required (without daughter board)
Typical 45mA
Maximum 100mA
Voltage 8 to 15 VDC

600-1029 enclosure

Top latches

OEM transceiver

Wireless range 1,000 feet (305 m) open air
Operating temperature 32 to 120°F (0 to 49°C)
Storage temperature -30 to 140°F (-34 to 60°C)

2 mm power jack

Terminal block

Daughter board

LEDs

Bottom latch

ON

1 2 3 4 5 6 7 8

Maximum relative
humidity

Dimensions 3.2 x 4.6 x 0.6 inches (8.1 x 11.7 x 1.5 cm)
Features Antenna tamper, jam detect, wall tamper,

Optional items:

4. Connect DC power to the OEM transceiver module using
2 mm power jacks (center positive) or connect flyleads to
the terminal block as labeled on the board.

Enclosure 600-1029
USB daughter board 59-873
Repeater daughter

board
Stand-off 40-262

LED operation

Regulatory information

Table 1 shows the LED indications for the OEM transceiver

module

Table 1: OEM transceiver module LED indications
Indication Green LED Red LED

Powered up On Off
Communication with daughter board On Flashing
Valid packet received One flash off Off or flashing

Manufacturer UTC Fire & Security Americas Corporation, Inc.

FCC compliance This device complies with FCC Rules Part 15.

Troubleshooting

The following table gives troubleshooting suggestions for the
OEM transceiver module.

California code This product cannot be sold in the state of

Table 2: OEM transceiver module troubleshooting
Problem Action

OEM transceiver module’s green
and red LEDs are off

OEM receiver module’s green LED
is on and the red LED is off

Specifications

Model 600-1046-95
Frequency 319.5 MHz
Compatibility All 319.5 MHz sensors and 319.5 MHz

receivers

1. Check that the transformer
is plugged in.

2. Check the transformer to
module wiring.

Check the daughter board
mounting.

Contact information

For contact information, see www.utcfireandsecurity.com or
www.interlogix.com.

For technical support, toll-free: 888.437.3287 in the US
including Alaska, Hawaii, Puerto Rico, and Canada. Outside
the tool-free area, contact your dealer.

Copyright © 2011 Interlogix, a UTC Fire & Security Company.
All rights reserved.

90% noncondensing

cover tamper

600-1031

1275 Red Fox Rd., Arden Hills, MN 55112-6943,
USA

Operation is subject to the following two
conditions:

1. This device may not cause harmful
interference.

2. This device must accept any interference that
may be received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved
by UTC Fire & Security can void the user’s
authority to operate the equipment.
FCC ID: B4Z-903-TCVR
IC: 867A-903-TCVR

California if used to receive fire signals (per
section 208-g, Chapter 1.5 Construction Materials
and Equipment Listings, Title 19, California Code
of Regulations
(http://osfm.fire.ca.gov/pdf/fireengineering/bml/t-

19.pdf)).

2 OEM Transceiver Module with Crystal Transmitter Installation Instructions