Intel BOXNUC7CJYH User Manual

Intel® NUC Products NUC7CJY/NUC7PJY
Technical Product Specification
Regulatory Models: NUC7JY (Kit/Mini PC)
NUC7JYB (Board)
February 2018
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
The Intel NUC Products NUC7CJY/NUC7PJY may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel NUC Products NUC7CJY/NUC7PJY Specification Update.
ii
Revision
Revision History
Date
001
First release of Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
January 2018 002
Spec Change
February 2018
Revision History
Disclaimer
This product specification applies to only the standard Intel® NUC Boards, Kits and Mini PCs with BIOS identifier JYGLKCPX.86A.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR ANY APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR.
All Intel® NUC Boards are evaluated as Information Technology Equipment (I.T.E.) for use in personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar locations. The suitability of this product for other PC or embedded non-PC applications or other environments, such as medical, industrial, alarm systems, test equipment, etc. may not be supported without further evaluation by Intel.
Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights.
Intel may make changes to specifications and product descriptions at any time, without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or
incompatibilities arising from future changes to them.
Intel processor numbers are not a measure of performance. Processor numbers differentiate features within each processor family, not across different processor families: Go to:
Learn About Intel® Processor Numbers
Intel NUC Boards and kits may contain design defects or errors known as errata, which may cause the product to deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications before placing your product order.
Intel, Pentium and Celeron are trademarks of Intel Corporation in the U.S. and/or other countries.
* Other names and brands may be claimed as the property of others.
Copyright 2018 Intel Corporation. All rights reserved.
ii
Note: For this Technical Products Specification, the use of Intel NUC Products
Intel NUC Board
AA Revision
BIOS Revision
Notes
NUC7CJYB
J67967-400
JYGLKCPX.86A.0027
1, 2
NUC7CJYB
J67970-400
JYGLKCPX.86A.0027
1, 2, 4
NUC7PJYB
J67969-400
JYGLKCPX.86A.0027
1, 3
Device
Stepping
S-Spec Number(s)
Intel Celeron processor
B0
SR3S5
Device
Stepping
S-Spec Number(s)
Intel Pentium Silver processor
B0
SR3S3
Device
Model
Version
SanDisk
SDINADF4-32G-H
5.1
Kingston
EMMC32G-M525-A53
5.1
Kingston
EMMC32G-TA28-A01
5.1
Product Name
Intel NUC Kit SA #
Intel® NUC Board AA #
Differentiating Features
NUC7CJYH
J67971-400
J67967-400
Kit with power adapter, no memory, no eMMC, no OS
NUC7PJYH
J67992-400
J67969-400
Kit with power adapter, no memory, no eMMC, no OS
NUC7CJYS
J67993-400
J67994-400
J67970-400
Mini PC with power adapter, preinstalled with 4GB 2400MHz DDR4 SO-DIMM, 32GB e-MMC with Microsoft* Windows* 10 Home
NUC7CJY/NUC7PJY refers to Intel NUC Kit NUC7CJYH, Intel NUC Kit NUC7PJYH, Intel NUC Mini PC NUC7CJYS, and Intel NUC Boards NUC7CJYB and NUC7PJYB.
Board Identification Information
Basic Intel® NUC Board Identification Information
Notes:
1. The AA number is found on a small label on the SO-DIMM memory connector.
2. Intel® Celeron® processor J4005 used on this AA revision consists of the following component:
3. Intel® Pentium® Silver processor J5005 used on this AA revision consists of the following component:
4. Contains a 32GB embedded MultiMediaCard (e-MMC) device consisting of one of the following components:
Product Identification Information
Intel® NUC Products NUC7{x}JY{y}† Identification Information
Note:
where {x} = “C” for “Celeron”, “P” for “Pentium”, and {y} = “H” for “kit” and “S” = “system”
iii
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Date
Type of Change
Description of Changes or Clarifications
February 2018
Specification Change
Correct Pentium core count Correct graphics designator
Specification Changes or Clarifications
The table below indicates the Specification Changes or Specification Clarifications that apply to the Intel NUC Products NUC7CJY/NUC7PJY.
Specification Changes or Clarifications
Errata
Current characterized errata, if any, are documented in a separate Specification Update. See
http://www.intel.com/content/www/us/en/nuc/overview.html for the latest documentation.
iv
Preface
Chapter
Description
1
A description of the hardware used in Intel NUC Products NUC7CJY/NUC7PJY
2
A map of the resources of the Intel NUC Board
3
The features supported by the BIOS Setup program
4
A description of the front panel blink codes and BIOS error messages
5
The features of the Intel NUC Kits and Mini PCs
This Technical Product Specification (TPS) specifies the layout, components, connectors, power and environmental requirements, and the BIOS for Intel® NUC Products NUC7CJY/NUC7PJY. The Intel® NUC Kits NUC7CJYH/NUC7PJYH are without memory and operating system, and the Intel® NUC Mini PC NUC7CJYS is with pre-installed SO-DIMM memory and operating system.
Intended Audience
The TPS is intended to provide detailed technical information about Intel NUC Products NUC7CJY/NUC7PJY and their components to the vendors, system integrators, and other engineers and technicians who need this level of information. It is specifically not intended for general audiences.
What This Document Contains
Typographical Conventions
This section contains information about the conventions used in this specification. Not all of these symbols and abbreviations appear in all specifications of this type.
Notes, Cautions, and Warnings
NOTE
Notes call attention to important information.
CAUTION
Cautions are included to help you avoid damaging hardware or losing data.
v
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
#
Used after a signal name to identify an active-low signal (such as USBP0#)
bpp
Bits per pixel
GB
Gigabyte (1,073,741,824 bytes)
GBps
Gigabytes per second
Gbps
Gigabits per second
KB
Kilobyte (1024 bytes)
Kb
Kilobit (1024 bits)
kbps
1000 bits per second
MB
Megabyte (1,048,576 bytes)
MBps
Megabytes per second
Mb
Megabit (1,048,576 bits)
Mbps
Megabits per second
TDP
Thermal Design Power
xxh
An address or data value ending with a lowercase h indicates a hexadecimal value.
x.x V
Volts. Voltages are DC unless otherwise specified.
*
This symbol is used to indicate third-party brands and names that are the property of their respective owners.
[ ]
Specific keyboard key callouts are enclosed in brackets, e.g., [ESC]
Other Common Notation
vi
Contents
Revision History ............................................................................................................... ii
Board Identification Information ..................................................................................................................... iii
Product Identification Information ................................................................................................................. iii
Errata ........................................................................................................................................................................... iv
Preface ............................................................................................................................... v
Intended Audience ................................................................................................................................................. v
What This Document Contains ......................................................................................................................... v
Typographical Conventions ............................................................................................................................... v
Contents .......................................................................................................................... vii
1 Product Description ............................................................................................... 11
1.1 Overview ...................................................................................................................................................... 11
1.1.1 Feature Summary .................................................................................................................. 11
1.1.2 Board Layout (Top) ............................................................................................................... 13
1.1.3 Board Layout (Bottom) ........................................................................................................ 14
1.1.4 Block Diagram ......................................................................................................................... 16
1.2 Online Support .......................................................................................................................................... 17
1.3 Processor ..................................................................................................................................................... 17
1.4 System Memory ........................................................................................................................................ 18
1.5 Processor Graphics Subsystem .......................................................................................................... 20
1.5.1 Intel® Ultra-High Definition (Intel® UHD) Graphics .................................................... 20
1.5.2 High Definition Multimedia Interface* (HDMI*) ......................................................... 20
1.6 USB ................................................................................................................................................................. 21
1.7 SATA Interface ........................................................................................................................................... 21
1.7.1 AHCI Mode ................................................................................................................................ 21
1.8 Embedded MultiMediaCard (e-MMC) - optional ......................................................................... 21
1.9 Real-Time Clock Subsystem ................................................................................................................ 22
1.10 Audio Subsystem ..................................................................................................................................... 23
1.10.1 Digital Microphone Array .................................................................................................... 24
1.10.2 Mini-TOSLINK Interface ...................................................................................................... 24
1.10.3 Audio Subsystem Software ............................................................................................... 24
1.11 LAN Subsystem ......................................................................................................................................... 25
1.11.1 Realtek* 8111HN Gigabit Ethernet Controller .......................................................... 25
1.11.2 LAN Subsystem Software ................................................................................................... 25
1.11.3 RJ-45 LAN Connector with Integrated LEDs .............................................................. 26
1.11.4 Wireless Network Module .................................................................................................. 26
1.12 Hardware Management Subsystem ................................................................................................. 27
1.12.1 Hardware Monitoring ........................................................................................................... 27
vii
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
1.12.2 Fan Monitoring ........................................................................................................................ 27
1.12.3 Thermal Solution ................................................................................................................... 28
1.13 Operating System Support .................................................................................................................. 28
1.14 Power Management ................................................................................................................................ 29
1.14.1 ACPI ............................................................................................................................................. 29
1.14.2 Hardware Support ................................................................................................................. 31
1.14.3 HDMI Consumer Electronics Control (CEC) ................................................................ 33
1.15 Intel Platform Security Technologies .............................................................................................. 35
1.15.1 Intel® Virtualization Technology ...................................................................................... 35
1.15.2 Intel® Platform Trust Technology ................................................................................... 35
2 Technical Reference ............................................................................................... 37
2.1 Memory Resources .................................................................................................................................. 37
2.1.1 Addressable Memory ........................................................................................................... 37
2.2 Connectors and Headers....................................................................................................................... 37
2.2.1 Front Panel Connectors ...................................................................................................... 38
2.2.2 Back Panel Connectors ....................................................................................................... 38
2.2.3 Headers and Connectors (Top) ........................................................................................ 39
2.2.4 Connectors and Headers (Bottom) ................................................................................. 40
2.3 BIOS Security Jumper ............................................................................................................................ 48
2.4 Mechanical Considerations .................................................................................................................. 50
2.4.1 Form Factor .............................................................................................................................. 50
2.5 Electrical Considerations ...................................................................................................................... 51
2.5.1 Power Supply Considerations .......................................................................................... 51
2.5.2 Fan Header Current Capability ......................................................................................... 51
2.6 Thermal Considerations ........................................................................................................................ 51
2.7 Reliability ..................................................................................................................................................... 54
2.8 Environmental ........................................................................................................................................... 54
3 Overview of BIOS Features ................................................................................... 55
3.1 Introduction ................................................................................................................................................ 55
3.2 BIOS Flash Memory Organization ..................................................................................................... 55
3.3 System Management BIOS (SMBIOS) .............................................................................................. 55
3.4 Legacy USB Support ............................................................................................................................... 56
3.5 BIOS Updates ............................................................................................................................................. 56
3.5.1 Language Support ................................................................................................................. 56
3.6 BIOS Recovery ........................................................................................................................................... 56
3.7 Boot Options .............................................................................................................................................. 57
3.7.1 Network Boot........................................................................................................................... 57
3.7.2 Booting Without Attached Devices ................................................................................ 57
3.7.3 Changing the Default Boot Device During POST ...................................................... 57
3.7.4 Power Button Menu .............................................................................................................. 58
3.8 Hard Disk Drive Password Security Feature .................................................................................. 59
3.9 BIOS Security Features .......................................................................................................................... 60
viii
Contents
4 Error Messages and Blink Codes ......................................................................... 61
4.1 Front-panel Power LED Blink Codes ................................................................................................ 61
4.2 BIOS Error Messages ............................................................................................................................... 61
5 Intel NUC Kit Features ........................................................................................... 62
5.1 Chassis Front Panel Features .............................................................................................................. 62
5.2 Chassis Rear Panel Features ................................................................................................................ 63
Figures
Figure 1. Major Board Components (Top) ....................................................................................................... 13
Figure 2. Major Board Components (Bottom) ................................................................................................ 14
Figure 3. Block Diagram ........................................................................................................................................... 16
Figure 4. Memory Channel and SO-DIMM Configuration.......................................................................... 19
Figure 5. 4-Pin 3.5 mm (1/8 inch) Audio Jack Pin Out ............................................................................... 23
Figure 6. Mini-TOSLINK Adaptor (not included) ........................................................................................... 24
Figure 7. LAN Connector LED Locations........................................................................................................... 26
Figure 8. Thermal Solution and Fan Header ................................................................................................... 28
Figure 9. Location of the Standby Power LED ............................................................................................... 33
Figure 10. CEC Connector ........................................................................................................................................ 34
Figure 11. Front Panel Connectors, Controls and Indicators .................................................................. 38
Figure 12. Back Panel Connectors ...................................................................................................................... 38
Figure 13. Headers and Connectors (Top) ....................................................................................................... 39
Figure 14. Connectors and Headers (Bottom) ............................................................................................... 40
Figure 15. Connection Diagram for Front Panel Header (2.0 mm Pitch) ............................................ 45
Figure 16. Location of the CIR Sensor ............................................................................................................... 47
Figure 17. Location of the BIOS Security Jumper ........................................................................................ 48
Figure 18. Board Dimensions ................................................................................................................................ 50
Figure 19. Board Height Dimensions ................................................................................................................. 51
Figure 20. Localized High Temperature Zones ............................................................................................. 52
Figure 21. Intel NUC Products NUC7CJYH/NUC7PJYH/NUC7CJYS Features – Front .................. 62
Figure 22. Intel NUC Products NUC7CJYH/NUC7PJYH/NUC7CJYS Features – Rear .................... 63
Tables
Table 1. Feature Summary ..................................................................................................................................... 11
Table 2. Components Shown in Figure 1 ......................................................................................................... 13
Table 3. Components Shown in Figure 2 ......................................................................................................... 15
Table 4. Supported Memory Configurations .................................................................................................. 18
Table 5. Unsupported Memory Configurations............................................................................................. 18
Table 6. LAN Connector LED States ................................................................................................................... 26
Table 7. Effects of Pressing the Power Switch ............................................................................................... 29
Table 8. Power States and Targeted System Power ................................................................................... 30
Table 9. Wake-up Devices and Events .............................................................................................................. 31
Table 10. HDMI 1 CEC expected behavior ........................................................................................................ 34
ix
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Table 11. Headers and Connectors Shown in Figure 13 ........................................................................... 39
Table 12. LPC Debug Header (2.0 mm Pitch – not stuffed) ...................................................................... 39
Table 13. Connectors and Headers Shown in Figure 14 ........................................................................... 41
Table 14. SATA Power Header (1.25 mm Pitch) ............................................................................................ 41
Table 15. Single-Port Internal USB 2.0 Headers (1.25 mm Pitch) ......................................................... 42
Table 16. Digital Microphone (DMICS) Array Connector (1.25 mm Pitch).......................................... 42
Table 17. RGB LED Connector (1.25 mm Pitch) ............................................................................................ 42
Table 18. Consumer Electronics Control (CEC) Connector (1.25 mm Pitch) .................................... 43
Table 19. SDXC Card Reader Connector .......................................................................................................... 43
Table 20. Auxiliary Power Connector ................................................................................................................ 44
Table 21. Front Panel Header (2.0 mm Pitch) ................................................................................................ 45
Table 22. States for a One-Color Power LED ................................................................................................. 46
Table 23. States for a Dual-Color Power LED ................................................................................................ 46
Table 24. BIOS Security Jumper Settings ........................................................................................................ 49
Table 25. Fan Header Current Capability ......................................................................................................... 51
Table 26. Thermal Considerations for Components ................................................................................... 53
Table 27. Tcontrol Values for Components ................................................................................................... 53
Table 28. Environmental Specifications ........................................................................................................... 54
Table 29. Acceptable Drives/Media Types for BIOS Recovery ............................................................... 56
Table 30. Boot Device Menu Options ................................................................................................................ 58
Table 31. Master Key and User Hard Drive Password Functions ........................................................... 59
Table 32. Supervisor and User Password Functions................................................................................... 60
Table 33. Front-panel Power LED Blink Codes ............................................................................................. 61
Table 34. BIOS Error Messages ............................................................................................................................ 61
Table 35. Components Shown in Figure 21 ................................................................................................... 62
Table 36. Components Shown in Figure 22 ................................................................................................... 63
x
Board Form Factor
4.0 inches by 4.0 inches (101.60 millimeters by 101.60 millimeters)
Processor
Intel NUC Kit NUC7CJYH / Intel NUC Mini PC NUC7CJYS
Soldered-down dual-core Intel® Celeron® processor J4005
up to 10 W TDP 4M Cache, 2.0 GHz base, 2.70 GHz turbo Intel
®
UHD Graphics 600
Integrated memory controller Integrated PCH
Intel NUC NUC7PJYH
Soldered-down quad-core Intel
®
Pentium® Silver processor J5005
up to 10 W TDP 4M Cache, 1.5 GHz base, 2.80 GHz turbo Intel
®
UHD Graphics 605
Integrated memory controller Integrated PCH
Memory
Support for DDR4 2133/2400 MHz SO-DIMMs Support for 4 Gb and 8 Gb memory technology Support for up to 8 GB of system memory with two SO-DIMMs Support for non-ECC memory Support for 1.2 V low voltage JEDEC memory 4 GB DDR4 2400 MHz SO-DIMM pre-installed (included in Intel NUC Mini PC
NUC7CJYS only)
Graphics
Integrated graphics support with Intel
®
UHD Graphics Technology:
Two High Definition Multimedia Interface* (HDMI*) 2.0a full-sized back panel
connectors
4K support, at 60 Hz
Audio
Intel® High Definition (Intel
®
HD) Audio via the HDMI v2.0 interfaces supporting
compressed 7.1digital audio
Realtek ALC233 HD Audio via a stereo microphone/headphone 3.5 mm jack on the
front panel
Compressed 5.1digital audio through a mini-TOSLINK jack on the back panel Digital microphone (DMIC) array header for support of digital voice assistants, such
as Microsoft* Cortana* and Amazon* Alexa* (dual digital array microphones are included with Intel® NUC Kits NUC7CJYH/NUC7PJYH and Intel® NUC Mini PC NUC7CJYS; not included with board-only SKUs)
1 Product Description
1.1 Overview
1.1.1 Feature Summary
Table 1 summarizes the major features of the product.
Table 1. Feature Summary
continued
11
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Peripheral Interfaces
USB 3.0 ports:
Two ports are implemented with external front panel connectors (one blue and
one amber charging capable)
Two ports are implemented with external back panel connectors (blue)
USB 2.0 ports:
Two ports via two single-port internal 1x4 1.25 mm pitch headers (white)
Consumer Infrared (CIR) Auxiliary power (AUX_PWR) – provides 1A of 5 VSB and DC
IN
power
Consumer Electronics Control (CEC) header Front panel header
Storage
One SATA 6.0 Gbps port (black)
Supports one 2.5“ SSD or HDD up to 9.5mm
One full-sized SDXC slot 32 GB embedded MultiMediaCard (e·MMC) onboard storage module (included in
Intel NUC Mini PC NUC7CJYS only)
BIOS
Intel
®
BIOS resident in the Serial Peripheral Interface (SPI) Flash device
Support for Advanced Configuration and Power Interface (ACPI), Plug and Play, and
System Management BIOS (SMBIOS)
LAN Support
Gigabit (10/100/1000 Mbps) LAN subsystem using the Realtek* 8111H-CG Gigabit Ethernet Controller
Hardware Monitor Subsystem
Hardware monitoring subsystem, based on an ITE* IT8987VG embedded controller, including:
Voltage sense to detect out of range power supply voltages Thermal sense to detect out of range thermal values One processor fan header Fan sense input used to monitor fan activity Simple fan speed control
Wireless
Intel® Wireless-AC 9462-D2W module
802.11ac, Dual Band, 1x1 (Diversity) Wi-Fi + Dual Mode Bluetooth 5 Maximum Transfer speed up to 433 Mbps Supports Intel® Smart Connect Technology Soldered-down module
Operating System
Supports Microsoft* Windows* 10 Home and Microsoft* Windows* 10 Pro Intel NUC Mini PC NUC7CJYS comes with Windows 10 Home pre-installed on an
e-MMC storage device
Only UEFI-enabled operating systems are supported. Legacy operating systems are
not supported. Please check your OS distributor for support details.
Additional Features
Integrated HDMI CEC (HDMI 1 only) Intel® Platform Trust Technology (Intel PTT) Generation 3
Table 1. Feature Summary (continued)
12
Product Description
Item from Figure 1
Description
A
Battery (lithium coin cell, CR2032, 3.0V)
B
LPC Debug header (not stuffed on production boards)
C
Thermal solution
D
Processor fan header
1.1.2 Board Layout (Top)
Figure 1 shows the location of the major components on the top-side of Intel NUC Boards NUC7CJYB/NUC7PJYB.
Table 2 lists the components identified in Figure 1.
Table 2. Components Shown in Figure 1
Figure 1. Major Board Components (Top)
13
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
1.1.3 Board Layout (Bottom)
Figure 2 shows the location of the major components on the bottom-side of Intel NUC Boards NUC7CJYB/NUC7PJYB.
14
Figure 2. Major Board Components (Bottom)
Table 3. Components Shown in Figure 2
Item from Figure 2
Description
A
12 - 19V DC input jack
B
Back panel USB 3.0 connectors
C
Back panel TOSLINK stereo jack/HDMI 2 connector
D
LAN jack
E
HDMI 1 connector
F
Auxiliary power connector (AUX_PWR) (1.25 mm pitch)
G
Digital microphone array (DMICS) connector (1.25 mm pitch)
H
Intel Wireless-AC 9462-D2W wireless LAN module
I
RGB LED header (RGB_LED) (1.25 mm pitch)
J
Front panel header (1.25 mm pitch)
K
BIOS security jumper
L
SATA power connector (1.25 mm pitch)
M
SDXC card reader slot
N
Front panel single-port USB 2.0 connector (1.25 mm pitch)
O
HDD LED
P
Front panel single-port USB 2.0 connector (1.25 mm pitch)
Q
+5 V Standby Power Indicator LED
R
Front panel USB 3.0 connector, charging capable (amber)
S
SATA 6.0 Gb/s connector
T
Front panel USB 3.0 connector (blue)
U
Front panel stereo speaker/headphone/microphone jack
V
Consumer Infrared (CIR) sensor
W
Power button / power LED
X
Consumer Electronic Control (CEC) connector
Y,Z
Dual DDR4 SO-DIMM sockets (SO-DIMM shown for illustration purposes; SO-DIMM supplied with
Intel NUC Mini PC NUC7CJYS only)
Product Description
15
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
1.1.4 Block Diagram
Figure 3 is a block diagram of the major functional areas of the board.
16
Figure 3. Block Diagram
Product Description
To find information about…
Visit this World Wide Web site:
Intel NUC Products NUC7CJY/NUC7PJY
http://www.intel.com/NUC
NUC Board Support
http://www.intel.com/NUCSupport
Available configurations for Intel NUC Products NUC7CJY/NUC7PJY
http://ark.intel.com
BIOS and driver updates
http://downloadcenter.intel.com
Tested memory
http://www.intel.com/NUCSupport
Integration information
http://www.intel.com/NUCSupport
1.2 Online Support
1.3 Processor
Intel NUC Kit NUC7CJYH, Intel NUC Mini PC NUC7CJS and Intel NUC Board NUC7CJYB have
a soldered-down System-on-a-Chip (SoC), which consists of:
Dual-core Intel Celeron processor J4005 Up to 10 W TDP 4M Cache, 2.0 GHz base, 2.70 GHz turbo Intel Integrated memory controller Integrated PCH
®
UHD Graphics 600
Intel NUC Kit NUC7PJY has a soldered-down System-on-a-Chip (SoC), which consists of:
Quad-core Intel Pentium Silver processor J5005 Up to 10 W TDP 4M Cache, 1.5 GHz base, 2.80 GHz turbo Intel
®
UHD Graphics 605
Integrated memory controller Integrated PCH
NOTE
The board has specific requirements for providing power to the processor. Refer to Section 2.5.1 on page 51 for information on power supply requirements for the board.
17
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
SO-DIMM Capacity
Configuration
(Note)
SDRAM Density
SDRAM Organization Front-side/Back-side
Number of SDRAM Devices
2048 MB
SS
4 Gbit
512 M x4/empty
4
4096 MB
DS
4 Gbit
512 M x4/512 M x4
8
4096 MB
SS
8 Gbit
1024 M x4/empty
4
8192 MB
DS
4 Gbit
512 M x8/512 M x8
16
8192 MB
DS
8 Gbit
1024 M x4/1024 M x4
8
SO-DIMM Capacity
Configuration
(Note)
SDRAM Density
SDRAM Organization Front-side/Back-side
Number of SDRAM Devices
1024 MB
SS
1 Gbit
128 M x8/empty
8
2048 MB
DS
1 Gbit
128 M x8/128 M x8
16
2048 MB
SS
2 Gbit
256 M x8/empty
8
4096 MB
DS
2 Gbit
256 M x8/256 M x8
16
1.4 System Memory
The board has two 260-pin SO-DIMM sockets and supports the following memory features:
1.2 V DDR4 2133/2400 MHz SDRAM non-ECC SO-DIMM with gold plated contacts Two memory channels Unbuffered, single-sided or double-sided SO-DIMMs using 4 Gb or 8 Gb technology
(density)
8 GB maximum total system memory (with 4 Gb or 8 Gb memory technology). Refer to
Section 2.1.1 on page 37 for information on the total amount of addressable memory.
Minimum recommended total system memory: 2048 MB Serial Presence Detect Optional 4 GB DDR4 2400 MHz SO-DIMM pre-installed (included in Intel NUC Mini PC
NUC7CJYS only)
NOTE
To be fully compliant with all applicable DDR SDRAM memory specifications, the board should be populated with SO-DIMMs that support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read the SPD data and program the chipset to accurately configure memory settings for optimum performance. If non-SPD memory is installed, the BIOS will attempt to correctly configure the memory settings, but performance and reliability may be impacted or the SO-DIMMs may not function under the determined frequency.
NOTE
Intel NUC Products NUC7CJY/NUC7PJY support only 4 Gb and 8 Gb memory technologies (also referred to as “SDRAM density”). Table 4 lists the supported SO-DIMM configurations. Table 5 lists the SO-DIMM configurations that are not supported.
Table 4. Supported Memory Configurations
Note: “DS” refers to double-sided memory modules and “SS” refers to single-sided memory modules.
Table 5. Unsupported Memory Configurations
Note: “DS” refers to double-sided memory modules and “SS” refers to single-sided memory modules.
18
Figure 4 illustrates the memory channel and SO-DIMM configuration.
For information about…
Refer to:
Tested Memory
http://www.intel.com/NUCSupport
Product Description
Figure 4. Memory Channel and SO-DIMM Configuration
19
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
1.5 Processor Graphics Subsystem
The board supports dual HDMI integrated graphics via the processor.
1.5.1 Intel
The Intel UHD graphics controller features the following:
3D rendering, media compositing, and video encoding. 3D graphics hardware acceleration supporting DirectX* 9.3/10/11.3/12, OpenCL* 2.0, OGL
ES 3.1, OpenGL* 4.3
Video decode hardware acceleration supporting H.265/HEVC @ Level 5.1 8b/10b, H.264
@ Level 5.2, MPEG2, MVC, VC-1, WMV9, JPEG, VP8 and VP9 formats
Video encode hardware acceleration supporting H.265/HEVC @ Level 4 8b, H.264 @ Level
5.2, JPEG, MVC, VP8 and VP9 (SW only) formats
Supports content protection using High-Bandwidth Digital Content Protection (HDCP) 2.2
and PAVP 2.0.
4x anti-aliasing.
®
Ultra-High Definition (Intel® UHD) Graphics
1.5.1.1 Video Memory Allocation
Intel® Dynamic Video Memory Technology (DVMT) is a method for dynamically allocating system memory for use as graphics memory to balance 2D/3D graphics and system performance. If your computer is configured to use DVMT, graphics memory is allocated based on system requirements and application demands (up to the configured maximum amount). When memory is no longer needed by an application, the dynamically allocated portion of memory is returned to the operating system for other uses.
1.5.2 High Definition Multimedia Interface* (HDMI*)
The HDMI ports are compliant with the HDMI 2.0a specification. The HDMI ports support standard, enhanced, or high definition video, plus multi-channel digital audio on a single cable. The ports are compatible with all ATSC and DVB HDTV standards and support eight full-range channels of lossless audio formats. The maximum supported resolution is 4096 x 2160 @ 60 Hz, 24 bpp. Maximum DDI data rate is 5.94 Gbps.
1.5.2.1.1 Integrated Audio Provided by the HDMI Interfaces
The following audio technologies are supported by the HDMI 2.0a interfaces directly from the SoC:
AC3 - Dolby* Digital Dolby Digital Plus
20
Product Description
For information about
Refer to
The location of the USB connectors on the back panel
Figure 12, page 38
The location of the USB connector on the front panel
Figure 2, page 14
1.6 USB
The USB port arrangement is as follows:
USB 3.0 ports:
Two ports are implemented with external front panel connectors (one blue and one
amber charging capable)
Two ports are implemented with external back panel connectors (blue) Maximum current is 900 mA for each blue port, 1.5 A for the amber charging port
USB 2.0 ports:
Two ports via two single-port internal 1x4 1.25 mm pitch headers (white) Maximum current is 500 mA for each port of the white headers (1 A total)
All the USB ports are high-speed, full-speed, and low-speed capable.
NOTE
Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use a shielded cable that meets the requirements for full-speed devices.
1.7 SATA Interface
The SoC provides one SATA port with a theoretical maximum transfer rate of 6.0 Gb/s. A point-to-point interface is used for host to device connections.
1.7.1 AHCI Mode
The board supports AHCI storage mode.
NOTE
Microsoft* Windows* 10 includes the necessary AHCI drivers without the need to install separate AHCI drivers during the operating system installation process. However, it is always good practice to update the AHCI drivers to the latest available by Intel.
1.8 Embedded MultiMediaCard (e-MMC) - optional
The Intel NUC Mini PC NUC7CJYS contains a 32 GB Embedded MultiMediaCard (e-MMC) onboard storage module with Windows 10 Home operating system preinstalled. The Intel NUC Kit NUC7CJYH and Intel NUC Kit NUC7PJYH do not contain e-MMc storage nor Windows 10 preinstalled.
21
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
1.9 Real-Time Clock Subsystem
A coin-cell lithium battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to 13 minutes/year at 25 ºC with 3.3 VSB applied via the power supply 5 V STBY rail.
NOTE
If the battery and AC power fail, date and time values will be reset and the user will be notified during the POST.
When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS RAM (for example, the date and time) might not be accurate. Replace the battery with an equivalent one. Figure 1 on page 13 shows the location of the battery.
22
Product Description
Pin Number
Pin Name
Description
1
Tip
Left Audio Out
2
Ring
Right Audio Out
3
Ring
Common/Ground
4
Sleeve
Audio In
1.10 Audio Subsystem
The product supports Intel HD Audio via the Realtek ALC233 audio codec. The audio subsystem supports the following features:
Analog line-out/Analog Headphone/Analog Microphone jack on the front panel High Definition Audio via a stereo microphone/headphone/optical jack on the back panel Support for 44.1 kHz/48 kHz/96 kHz sample rates on all analog outputs Support for 44.1 kHz/48 kHz/96 kHz sample rates on all analog inputs Support for digital microphone (DMIC) array via onboard header Back Panel Audio Jack Support (see Figure 5 for 3.5 mm audio jack pin out):
Speakers only Headphones only Microphone only Combo Headphone/Microphone Mini-TOSLINK support (see section 1.10.2 for details)
Front Panel Audio Jack Support (see Figure 5 for 3.5 mm audio jack pin out):
Speakers only Headphones only Microphone only Combo Headphone/Microphone
Figure 5. 4-Pin 3.5 mm (1/8 inch) Audio Jack Pin Out
NOTE
The analog circuit of the back panel audio connector is designed to power headphones or amplified speakers only. Poor audio quality occurs if passive (nonamplified) speakers are connected to this output.
23
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
For information about
Refer to
Obtaining Audio software and drivers
http://downloadcenter.intel.com
1.10.1 Digital Microphone Array
The product supports a digital microphone (DMIC) array header for use of digital voice assistants, such as Microsoft* Cortana. Intel NUC Kit NUC7CJYH, Intel NUC Kit NUC7PJYH and Intel NUC Mini PC NUC7CJYS include dual digital array microphones mounted in the chassis on either side of the front panel.
1.10.2 Mini-TOSLINK Interface
The 3.5 mm audio jack also provides TOSLINK optical digital audio output.
Mini-TOSLINK interface (back panel) plus analog audio out
PCM datastream support S/PDIF datastream support Mini-TOSLINK adaptor (not included) necessary to connect to standard TOSLINK cable Stereo audio out
Figure 6. Mini-TOSLINK Adaptor (not included)
1.10.3 Audio Subsystem Software
Audio software and drivers are available from Intel’s World Wide Web site.
24
1.11 LAN Subsystem
For information about
Refer to
LAN software and drivers
http://downloadcenter.intel.com
For information about
Refer to
Full LAN Hardware feature set
http://www.realtek.com.tw/
For information about
Refer to
Obtaining LAN software and drivers
http://downloadcenter.intel.com
The LAN subsystem consists of the following:
Realtek 8111HN-CG Gigabit Ethernet Controller (10/100/1000 Mb/s) RJ-45 LAN connector with integrated status LEDs Intel® Wireless-AC 9462-D2W module
Additional features of the LAN subsystem include:
CSMA/CD protocol engine Jumbo frame support 9K LAN connect interface between the SoC and the LAN controller Power management capabilities
ACPI technology support LAN wake capabilities
LAN subsystem software
Product Description
1.11.1 Realtek* 8111HN Gigabit Ethernet Controller
The Realtek 8111HN Gigabit Ethernet Controller supports the following features:
10/100/1000 BASE-T IEEE 802.3 compliant Energy Efficient Ethernet (EEE) IEEE802.3az support (Low Power Idle (LPI) mode) Dual interconnect between the Integrated LAN Controller and the Physical Layer (PHY):
PCI Express-based interface for active state operation (S0) state
SMBUS for host and management traffic (Sx low power state) Compliant to IEEE 802.3x flow control support 802.1p and 802.1q TCP, IP, and UDP checksum offload (for IPv4 and IPv6) Full device driver compatibility
1.11.2 LAN Subsystem Software
LAN software and drivers are available from Intel’s World Wide Web site.
25
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Item
Description
A
Link LED (Green)
B
Data Rate LED (Green/Yellow)
LED
LED Color
LED State
Condition
Link (A)
Green
Off
LAN link is not established.
On
LAN link is established.
Blinking
LAN activity is occurring.
Data Rate (B)
Green/Yellow
Off
10 Mb/s data rate is selected.
Green
100 Mb/s data rate is selected.
Yellow
1000 Mb/s data rate is selected.
For information about
Refer to
Obtaining WLAN software and drivers
http://downloadcenter.intel.com
Full Specifications
http://intel.com/wireless
I-PEX MH4F coax antenna specifications
https://www.i-pex.com/Products/detail/17#!
1.11.3 RJ-45 LAN Connector with Integrated LEDs
Two LEDs are built into the RJ-45 LAN connector (shown in Figure 7).
Figure 7. LAN Connector LED Locations
Table 6 describes the LED states when the board is powered up and the LAN subsystem is operating.
Table 6. LAN Connector LED States
1.11.4 Wireless Network Module
The Intel Wireless-AC 9462-D2W module provides hi-speed wireless connectivity with the following capabilities:
802.11ac, Dual Band, 1x1 (Diversity) Wi-Fi + Dual Mode Bluetooth 5.0 Supports 2.4 Ghz and 5 Ghz bands Maximum transfer speed up to 433 Mbps FIPS9 and FISMA compliant Supports Intel® Smart Connect Technology Supports Multi-user multiple-input and multiple-output (MU-MIMO) technologies for
wireless communications
Soldered-down module Antenna coax connector specification is I-PEX MH4F
26
Product Description
For information about
Refer to
Wired for Management (WfM) Specification
www.intel.com/design/archives/wfm/
1.12 Hardware Management Subsystem
The hardware management features enable the board to be compatible with the Wired for Management (WfM) specification. The board has several hardware management features, including thermal and voltage monitoring.
1.12.1 Hardware Monitoring
The hardware monitoring and fan control subsystem is based on an ITE IT8987VG embedded controller, which supports the following:
Processor and system ambient temperature monitoring Chassis fan speed monitoring Voltage monitoring of +5 V, +3.3 V, Memory Vcc (SDRAM) SMBus interface
1.12.2 Fan Monitoring
Fan monitoring can be implemented using third-party software.
27
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Item
Description
A
Processor fan header
B
Thermal solution
1.12.3 Thermal Solution
Figure 8 shows the location of the thermal solution and processor fan header.
Figure 8. Thermal Solution and Fan Header
1.13 Operating System Support
Only UEFI-enabled operating systems, such as Microsoft* Windows* 10 Home and Microsoft* Windows* 10 Pro, are supported. Legacy operating systems are not supported. Please check your OS distributor for support details.
Intel NUC Mini PC NUC7CJYS comes with Windows 10 Home pre-installed on an e-MMC storage device.
28
Product Description
If the system is in this state…
…and the power switch is pressed for
…the system enters this state
Off (ACPI G2/G5 – Soft off)
Less than four seconds
Power-on (ACPI G0 – working state)
On (ACPI G0 – working state)
Less than four seconds
Soft-off/Standby (ACPI G1 – sleeping state)
Note
On (ACPI G0 – working state)
More than six seconds
Fail safe power-off (ACPI G2/G5 – Soft off)
Sleep (ACPI G1 – sleeping state)
Less than four seconds
Wake-up (ACPI G0 – working state)
Sleep (ACPI G1 – sleeping state)
More than six seconds
Power-off (ACPI G2/G5 – Soft off)
1.14 Power Management
Power management is implemented at several levels, including:
Software support through Advanced Configuration and Power Interface (ACPI) Hardware support:
Power Input
Instantly Available PC technology
LAN wake capabilities
Wake from USB
WAKE# signal wake-up support
Wake from S5
Wake from CIR
+5 V Standby Power Indicator LED
1.14.1 ACPI
ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer. The use of ACPI with this board requires an operating system that provides full ACPI support. ACPI features include:
Plug and Play (including bus and device enumeration) Power management control of individual devices, add-in boards (some add-in boards may
require an ACPI-aware driver), video displays, and disk drives
Methods for achieving less than 15-watt system operation in the power-on/standby
sleeping state
A Soft-off feature that enables the operating system to power-off the computer Support for multiple wake-up events (see Table 9 on page 31) Support for a front panel power and sleep mode switch
Table 7 lists the system states based on how long the power switch is pressed, depending on how ACPI is configured with an ACPI-aware operating system.
Table 7. Effects of Pressing the Power Switch
Note: Depending on power management settings in the operating system.
29
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Global States
Sleeping States
Processor States
Device States
Targeted System Power
(Note 1)
G0 – working state
S0 – working
C0 – working
D0 – working state.
Full power
G1 – sleeping state
S3 – Suspend to RAM. Context saved to RAM.
No power
D3 – no power except for wake-up logic.
Power < 5 W
(Note 2)
G1 – sleeping state
S4 – Suspend to disk. Context saved to disk.
No power
D3 – no power except for wake-up logic.
Power < 5 W
(Note 2)
G2/S5
S5 – Soft off. Context not saved. Cold boot is required.
No power
D3 – no power except for wake-up logic.
Power < 5 W
(Note 2)
G3 – mechanical off
AC power is disconnected from the computer.
No power to the system.
No power
D3 – no power for wake-up logic, except when provided by battery or external source.
No power to the system. Service can be performed safely.
1.14.1.1 System States and Power States
Under ACPI, the operating system directs all system and device power state transitions. The operating system puts devices in and out of low-power states based on user preferences and knowledge of how devices are being used by applications. Devices that are not being used can be turned off. The operating system uses information from applications and user settings to put the system as a whole into a low-power state.
Table 8 lists the power states supported by the board along with the associated system power targets. See the ACPI specification for a complete description of the various system and power states.
Table 8. Power States and Targeted System Power
Notes:
1. Total system power is dependent on the system configuration, including add-in boards and peripherals powered
by the system chassis’ power supply.
2. Dependent on the standby power consumption of wake-up devices used in the system.
30
Product Description
Devices/events that wake up the
system…
…from this sleep state
Comments
Power switch
S3, S4, S5
RTC alarm
S3, S4, S5
(Note 1)
Monitor to remain in sleep state
LAN
S3, S4, S5
(Notes 1, 2)
“S5 WOL after G3” must be supported;
monitor to remain in sleep state
USB
S3, S4, S5
(Note 3, 4)
Wake S4, S5 controlled by BIOS option
PCIe via WAKE#
S3, S4, S5
(Note 1)
Via WAKE; monitor to remain in sleep state
Consumer IR
S3, S4, S5
(Notes 3, 4)
Bluetooth
N/A
Wake from Bluetooth is not supported
1.14.1.2 Wake-up Devices and Events
Table 9 lists the devices or specific events that can wake the computer from specific states.
Table 9. Wake-up Devices and Events
Notes:
1. Monitor will remain in “sleep” state from S3 only
2. “S5 WoL after G3” supported w/Deep Sleep disabled
3. Wake from S4 and S5 only supported w/Deep Sleep disabled
4. Wake from device/event not supported immediately upon return from AC loss
NOTE
The use of these wake-up events from an ACPI state requires an operating system that provides full ACPI support. In addition, software, drivers, and peripherals must fully support ACPI wake events.
1.14.2 Hardware Support
The board provides several power management hardware features, including:
Wake from Power Button signal Instantly Available PC technology LAN wake capabilities Wake from USB WAKE# signal wake-up support Wake from S5 Wake from CIR +5 V Standby Power Indicator LED
NOTE
The use of Wake from USB from an ACPI state requires an operating system that provides full ACPI support.
31
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
1.14.2.1 Power Input
When resuming from an AC power failure, the computer may return to the power state it was
in before power was interrupted (on or off). The computer’s response can be set using the Last Power State feature in the BIOS Setup program’s Boot menu.
1.14.2.2 Instantly Available PC Technology
Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-RAM) sleep-state. While in the S3 sleep-state, the computer will appear to be off (the power supply is off, and the front panel LED is amber if dual colored, or off if single colored.) When signaled by a wake-up device or event, the system quickly returns to its last known wake state. Table 9 lists the devices and events that can wake the computer from the S3 state.
The use of Instantly Available PC technology requires operating system support and drivers for any installed PCI Express add-in card.
1.14.2.3 LAN Wake Capabilities
LAN wake capabilities enable remote wake-up of the computer through a network. The LAN subsystem monitors network traffic at the Media Independent Interface. Upon detecting a Magic Packet* frame, the LAN subsystem asserts a wake-up signal that powers up the computer.
1.14.2.4 Wake from USB
USB bus activity wakes the computer from an ACPI S3, S4, and S5 states.
NOTE
Wake from USB requires the use of a USB peripheral that supports Wake from USB.
1.14.2.5 WAKE# Signal Wake-up Support
When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from an ACPI S3, S4, or S5 state.
1.14.2.6 Wake from S5
When the RTC Date and Time is set in the BIOS, the computer will automatically wake from an ACPI S5 state.
1.14.2.7 Wake from Consumer IR
CIR activity wakes the computer from an ACPI S3, S4, or S5 state.
1.14.2.8 +5 V Standby Power Indicator LED
The standby power indicator LED shows that power is still present even when the computer appears to be off. Figure 9 shows the location of the standby power LED.
32
Product Description
CAUTION
If AC power has been switched off and the standby power indicator is still lit, disconnect the power cord before installing or removing any devices connected to the board. Failure to do so could damage the board and any attached devices.
Figure 9. Location of the Standby Power LED
1.14.3 HDMI Consumer Electronics Control (CEC)
The board contains two mutually-exclusive methods for controlling HDMI CEC devices:
External CEC adaptor connected via CEC connector (see Figure 14; pinout in Table 18).
Onboard CEC control from the embedded controller via HDMI cable connected to HDMI 1 and BIOS setup. Expected behavior is provided in Table 10 below.
33
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Activity
Current Status
Action
Expected Behavior
PC
1,2
TV3
Wake On TV
Off
Off
TV on
PC on
Standby by TV
On
On
TV Standby
PC sleep or power off4
Auto Turn Off TV (S0 -> S5)
On
On
PC Shutdown
TV standby3
Auto Turn On TV (S5 -> S0)
Off
Off
PC On
TV on3
Auto Turn Off TV (S0 -> S3)
On
On
PC Sleep
TV standby3
Auto Turn On TV (S3 -> S0)
Off
Off
PC On
TV on3
Table 10. HDMI 1 CEC expected behavior
Notes:
1. HDMI CEC Control enabled in BIOS Setup and in TV setup, if necessary. Please consult your TV’s documentation.
2. Fast Boot and Deep S4/S5 disabled in BIOS Setup.
3. Results seen with Panasonic LED TV VIERA TH-40A400W. Other TVs may have different results due to variable
implementations of CEC features.
4. PC power off behavior dependent upon power button setting in operating system.
5. If using external CEC adaptor, onboard CEC control must be disabled in BIOS Setup.
Figure 10. CEC Connector
34
Product Description
For information about
Refer to
Intel Virtualization Technology
http://www.intel.com/technology/virtualization/technology.htm
For information about
Refer to
Intel Platform Trust Technology
http://www.intel.com/content/dam/www/public/us/en/documents /white-papers/enterprise-security-platform-trust-technology­white-paper.pdf
1.15 Intel Platform Security Technologies
Intel platform security technologies provides tools and resources to help the user protect their information by creating a safer computing environment.
NOTE
Software with security capability is required to take advantage of Intel platform security technologies.
1.15.1 Intel® Virtualization Technology
Intel Virtualization Technology (Intel® VT) is a hardware-assisted technology that, when combined with software-based virtualization solutions, provides maximum system utilization by consolidating multiple environments into a single server or client.
NOTE
A processor with Intel VT does not guarantee that virtualization will work on your system. Intel VT requires a computer system with a chipset, BIOS, enabling software and/or operating system, device drivers, and applications designed for this feature.
1.15.2 Intel® Platform Trust Technology
Intel® Platform Trust Technology (Intel® PTT) Generation 3 is a platform functionality for credential storage and key management. Intel® PTT supports Microsoft* BitLocker* Drive Encryption for hard drive encryption and supports all Microsoft requirements for firmware Trusted Platform Module (fTPM) 2.0.
NOTE
Support for fTPM version 2.0 requires a true UEFI-enabled operating system, such as Microsoft* Windows* 10.
CAUTION
BIOS recovery using the BIOS security jumper clears Intel® Platform Trust Technology (Intel® PTT) keys. These keys will not be restored after the BIOS recovery.
35
2 Technical Reference
2.1 Memory Resources
2.1.1 Addressable Memory
The board utilizes up to 8 GB of addressable system memory. Typically the address space that is allocated for PCI Conventional bus add-in cards, PCI Express configuration space, BIOS (SPI Flash device), and chipset overhead resides above the top of DRAM (total system memory). On a system that has 8 GB of system memory installed, it is not possible to use all of the installed memory due to system address space being allocated for other system critical functions. These functions include the following:
BIOS/SPI Flash device (16 MB) Local APIC (19 MB) Direct Media Interface (40 MB) PCI Express configuration space (256 MB) SoC base address registers PCI Express ports (up to 256 MB) Memory-mapped I/O (I/O fabric) that is dynamically allocated for PCI Express add-in cards
(256 MB)
The board provides the capability to reclaim the physical memory overlapped by the memory mapped I/O logical address space. The board remaps physical memory from the top of usable DRAM boundary to the 4 GB boundary to an equivalent sized logical address range located just above the 4 GB boundary. All installed system memory can be used when there is no overlap of system addresses.
2.2 Connectors and Headers
CAUTION
Only the following connectors and headers have overcurrent protection: back panel and front panel USB.
This section describes the board’s connectors and headers. The connectors and headers can be divided into these groups:
Front panel I/O connector Back panel I/O connectors
37
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Item
Description
A
Power switch and LED
B
CIR
C
Front panel stereo microphone/headphone jack
D
USB 3.0 port (blue)
E
USB 3.0 charging-capable port (amber)
F
Hard drive activity LED
Item
Description
A
HDMI 1 connector
B
LAN
C
HDMI 2 connector
D
Back panel TOSLINK stereo jack
E
USB 3.0 ports
F
12 - 19V DC input jack
2.2.1 Front Panel Connectors
Figure 11 shows the location of the front panel connectors, controls and indicators for the board.
Figure 11. Front Panel Connectors, Controls and Indicators
2.2.2 Back Panel Connectors
Figure 12 shows the location of the back panel connectors for the board.
Figure 12. Back Panel Connectors
38
2.2.3 Headers and Connectors (Top)
Item from Figure 13
Description
A
LPC debug header (not stuffed) – see Table 12
B
Processor fan header
Pin
Signal Name
Description
Pin
Signal Name
Description
1
LPC_DB_AD3
Address line 3
2
LPC_VCC3
+3.3V VCC
3
LPC_DB_AD2
Address line 2
4
DB_LPC_FRAME_L
LPC Frame
5
LPC_DB_AD1
Address line 1
6
DB_RST_L
Reset
7
LPC_DB_AD0
Address line 0
8
DB_LPC_CLK
LPC clock
9
GND
Ground
10
Key
No pin
Figure 13 shows the location of the headers and connectors on the top-side of the board.
Technical Reference
Figure 13. Headers and Connectors (Top)
Table 11 lists the headers and connectors identified in Figure 13.
Table 11. Headers and Connectors Shown in Figure 13
Table 12. LPC Debug Header (2.0 mm Pitch – not stuffed)
39
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
2.2.4 Connectors and Headers (Bottom)
Figure 14 shows the locations of the connectors and headers on the bottom-side of the board.
Figure 14. Connectors and Headers (Bottom)
40
Table 13 lists the connectors and headers identified in Figure 14.
Item from Figure 14
Description
A
Auxiliary power connector (AUX_PWR) (1.25 mm pitch)
B
Digital microphone array connector (DMICS)
C
RGB LED connector (RGB_LED)
D
Auxiliary front panel connector (FRONT_PANEL) (2.0 mm pitch)
E
BIOS security jumper (BIOS_SEC)
F
SATA power connector (1.25 mm pitch)
G
SDXC slot
H, I
Front panel single-port USB 2.0 header (USB1/USB2) (1.25 mm pitch)
J
SATA 6.0 Gb/s connector (SATA)
K
Consumer Electronics Control (CEC) connector (1.25 mm pitch)
Pin
Signal Name
1
5 V
2
5 V 3 3.3 V
4
GND 5 GND
Table 13. Connectors and Headers Shown in Figure 14
Technical Reference
Signal Tables for the Connectors and Headers
Table 14. SATA Power Header (1.25 mm Pitch)
NOTE
Connector is Molex* part number 53398-0571, 1.25 mm pitch PicoBlade* header, surface mount, vertical, lead-free, 5 circuits.
41
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Pin
Signal Name
1
+5 V DC
2
Data (negative)
3
Data (positive)
4
Ground
Pin
Signal Name
1
Ground
2
+3.3 V DC (+3V3_DMIC)
3
Clock (DMIC_CLK)
4
Data (DMIC_DAT)
Pin
Signal Name
1
+3.3VSB
2
Red LED
3
Green LED
4
Blue LED
Table 15. Single-Port Internal USB 2.0 Headers (1.25 mm Pitch)
NOTE
Connector is Molex part number 53398-0571, 1.25 mm pitch PicoBlade header, surface
mount, vertical, lead-free, 4 circuits.
The +5 V DC power on the USB header is fused. Use only an internal USB connector that conforms to the USB 2.0 specification for high-speed
USB devices.
Table 16. Digital Microphone (DMICS) Array Connector (1.25 mm Pitch)
NOTE
Connector is Molex part number 53398-0571, 1.25 mm pitch PicoBlade header, surface mount, vertical, lead-free, 4 circuits.
Table 17. RGB LED Connector (1.25 mm Pitch)
NOTE
Connector is Molex part number 53398-0571, 1.25 mm pitch PicoBlade header, surface mount, vertical, lead-free, 4 circuits.
42
Technical Reference
Pin
Signal Name
1
+5VSB
2
Ground
3
CEC_PWR
4
HDMI_CEC
Pin
Signal Name
Descriptive Name
1
CD
Card Detection
2
DATA2
Serial Data 2
3
DATA3
Serial Data 3
4
CMD
Command
5
VSS1
Ground
6
VDD
Power (3.3 V)
7
CLK
Serial Clock
8
VSS2
Ground
9
DATA0
Serial Data 0
10
DATA1
Serial Data 1
11
WP
Write Protect
Table 18. Consumer Electronics Control (CEC) Connector (1.25 mm Pitch)
NOTE
Connector is Molex part number 53398-0571, 1.25 mm pitch PicoBlade header, surface mount, vertical, lead-free, 4 circuits.
2.2.4.1 SDXC Card Reader
The board has a standard Secure Digital (SD) card reader that supports the Secure Digital eXtended Capacity (SDXC) format, 3.01 specification.
Table 19. SDXC Card Reader Connector
NOTE
The SD card reader is not supported in Microsoft* Windows* 7
43
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Pin
Signal Name
Descriptive Name
1
+5VSB
5V
2
PCH_GPIO24
Power draw sensor
3
GND
Ground
4
+VIN
12V – 19V DC input
For information about
Refer to
Power supply considerations
Section 2.5.1, page 51
2.2.4.2 Power Supply Connector
The board has the following power supply connector:
External Power Supply – the board is powered through a 12-19 V DC connector on the back
panel. The back panel DC connector is compatible with a 5.5 mm/OD (outer diameter) and
2.5 mm/ID (inner diameter) plug, where the inner contact is +19 (±10%) V DC and the shell is GND. The maximum current rating is 3 A.
NOTE
External power voltage, 12-19 V DC, is dependent on the type of power adapter used.
Table 20. Auxiliary Power Connector
NOTE
The Auxiliary Power Connector is a limited voltage source (output) for 5V Standby and the voltage supplied to the board (typically 19V DC) for use by expansion peripherals. The Auxiliary Power Connector is limited to 1.5A max total current (fused).
NOTE
Connector is JTE (JOINT TECH): A1250WV-S-04P A-Series (Wire to Board) Vertical SMT Connector,
1.25mm pitch, 1A rating. Mates with JTE A1250 Series Housing.
44
Technical Reference
Pin
Signal Name
Description
Pin
Signal Name
Description
1
HDD_POWER_LED
Pull-up resistor (750 Ω) to +5V
2
POWER_LED_MAIN
[Out] Front panel LED (main color)
3
HDD_LED#
[Out] Hard disk activity LED
4
POWER_LED_ALT
[Out] Front panel LED (alt color)
5
GROUND
Ground
6
POWER_SWITCH#
[In] Power switch
7
RESET_SWITCH#
[In] Reset switch
8
GROUND
Ground
9
+5V_DC
Power (2A)
10
Key
No pin
2.2.4.3 Front Panel Header (2.0 mm Pitch)
This section describes the functions of the front panel header. Table 21 lists the signal names of the front panel header. Figure 15 is a connection diagram for the front panel header.
Table 21. Front Panel Header (2.0 mm Pitch)
Figure 15. Connection Diagram for Front Panel Header (2.0 mm Pitch)
2.2.4.3.1 Hard Drive Activity LED Header
Pins 1 and 3 can be connected to an LED to provide a visual indicator that data is being read from or written to a hard drive. Proper LED function requires a SATA hard drive or optical drive connected to an onboard SATA connector.
2.2.4.3.2 Reset Switch Header
Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST.
45
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
LED State
Description
Off
Power off
Blinking
Standby
Steady
Normal operation
LED State
Description
Off
Power off
Secondary color blinking (amber)
Standby Primary color steady (blue)
Normal operation
For information about
Refer to
Power supply considerations
Section 2.5.1, page 51
2.2.4.3.3 Power/Sleep LED Header
Pins 2 and 4 can be connected to a one- or two-color LED. Table 22 and Table 23 show the possible LED states.
Table 22. States for a One-Color Power LED
Table 23. States for a Dual-Color Power LED
NOTE
The LED behavior shown in Table 22 is default – other patterns may be set via BIOS setup.
2.2.4.3.4 Power Switch Header
Pins 6 and 8 can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply will recognize another on/off signal.
2.2.4.3.5 5V DC Power Header
Pin 6 can supply 2A of 5V DC (VCC) power. Any usage of power from this header should be considered when calculating the system’s total power budget.
46
Technical Reference
Item
Description
A
CIR Sensor
2.2.4.4 Consumer Infrared (CIR) Sensor
The Consumer Infrared (CIR) sensor on the front panel provides features that are designed to comply with Microsoft Consumer Infrared usage models.
The CIR feature is made up of the receiving sensor. The receiving sensor consists of a filtered translated infrared input compliant with Microsoft CIR specifications.
Customers are required to provide their own media center compatible remote or smart phone application for use with the Intel NUC. Figure 16 shows the location of the CIR sensor.
Figure 16. Location of the CIR Sensor
47
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
2.3 BIOS Security Jumper
CAUTION
Do not move a jumper with the power on. Always turn off the power and unplug the power cord from the computer before changing a jumper setting. Otherwise, the board could be damaged.
Figure 17 shows the location of the BIOS security jumper. The 3-pin jumper determines the BIOS Security program’s mode. Table 24 describes the BIOS security jumper settings for the three modes: normal, lockdown, and configuration.
Figure 17. Location of the BIOS Security Jumper
48
Table 24. BIOS Security Jumper Settings
Function/Mode
Jumper Setting
Configuration
Normal
1-2
The BIOS uses current configuration information and passwords for booting.
Lockdown
2-3
The BIOS uses current configuration information and passwords for booting, except:
• All POST Hotkeys are suppressed (prompts are not displayed and keys are not accepted. For example, F2 for Setup, F10 for the Boot Menu).
• Power Button Menu is not available (see Section 3.7.4 Power Button Menu).
BIOS updates are not available except for automatic Recovery due to flash corruption.
Configuration
None
BIOS Recovery Update process if a matching *.bio file is found. Recovery Update can be cancelled by pressing the Esc key.
If the Recovery Update was cancelled or a matching *.bio file was not found, a Config Menu will be displayed. The Config Menu consists of the following (followed by the Power Button Menu selections):
[1] Suppress this menu until the BIOS Security Jumper is replaced.
[2] Clear BIOS User and Supervisor Passwords.
See Section 3.7.4 Power Button Menu.
Technical Reference
49
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
2.4 Mechanical Considerations
2.4.1 Form Factor
The board is designed to fit into a custom chassis. Figure 18 illustrates the mechanical form factor for the board. Dimensions are given in millimeters. The outer dimensions are
101.60 millimeters by 101.60 millimeters [4.0 inches by 4.0 inches].
50
Figure 18. Board Dimensions
Figure 19 shows the height dimensions of the board.
Fan Header
Maximum Available Current
Processor fan
.25 A
Figure 19. Board Height Dimensions
2.5 Electrical Considerations
2.5.1 Power Supply Considerations
Technical Reference
System power requirements will depend on actual system configurations chosen by the integrator, as well as end user expansion preferences. It is the system integrator’s responsibility to ensure an appropriate power budget for the system configuration is properly assessed based on the system-level components chosen.
2.5.2 Fan Header Current Capability
Table 25 lists the current capability of the fan header.
Table 25. Fan Header Current Capability
2.6 Thermal Considerations
CAUTION
A chassis with a maximum internal ambient temperature of 58 oC at the processor fan inlet is recommended. If the internal ambient temperature exceeds 58 oC, further thermal testing is required to ensure components do not exceed their maximum case temperature.
CAUTION
Failure to ensure appropriate airflow may result in reduced performance of both the processor and/or voltage regulator or, in some instances, damage to the board.
All responsibility for determining the adequacy of any thermal or system design remains solely with the system integrator. Intel makes no warranties or representations that merely following the instructions presented in this document will result in a system with adequate thermal performance.
51
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Item
Description
A
Processor voltage regulator area
B
Thermal solution
CAUTION
Ensure that the ambient temperature does not exceed the board’s maximum operating temperature. Failure to do so could cause components to exceed their maximum case temperature and malfunction. For information about the maximum operating temperature, see the environmental specifications in Section 2.8.
CAUTION
The processor voltage regulator area (shown in Figure 20) can reach a temperature of up to
97.5 oC in an open chassis. Ensure that proper airflow is maintained in the processor voltage regulator circuit. Failure to do so may result in shorter than expected product lifetime.
Figure 20 shows the locations of the localized high temperature zones.
52
Figure 20. Localized High Temperature Zones
Technical Reference
Component
Maximum Case Temperature
Processor
For processor case temperature, see processor datasheets and processor specification updates
Component
Tcontrol
Processor
For processor case temperature, see processor datasheets and processor specification updates
For information about
Refer to
Processor datasheets and specification updates
Section 1.2, page 17
Table 26 provides maximum case temperatures for the components that are sensitive to thermal changes. The operating temperature, current load, or operating frequency could affect case temperatures. Maximum case temperatures are important when considering proper airflow to cool the board.
Table 26. Thermal Considerations for Components
To ensure functionality and reliability, the component is specified for proper operation when Case Temperature is maintained at or below the maximum temperature listed in Table 27. This is a requirement for sustained power dissipation equal to Thermal Design Power (TDP is specified as the maximum sustainable power to be dissipated by the components). When the component is dissipating less than TDP, the case temperature should be below the Maximum Case Temperature. The surface temperature at the geometric center of the component corresponds to Case Temperature.
It is important to note that the temperature measurement in the system BIOS is a value reported by embedded thermal sensors in the components and does not directly correspond to the Maximum Case Temperature. The upper operating limit when monitoring this thermal sensor is Tcontrol.
Table 27. Tcontrol Values for Components
53
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Parameter
Specification
Temperature
Non-Operating
-40 C to +60 C
Operating
0 C to +50 C
The operating temperature of the board may be determined by measuring the air temperature from the junction of the heatsink fins and fan, next to the attachment screw, in a closed chassis, while the system is in operation.
Shock
Unpackaged
50 g trapezoidal waveform
Velocity change of 170 inches/s²
Packaged
Free fall package drop machine set to the height determined by the weight of the package.
Product Weight (pounds)
Free Fall (inches)
<20
36 21-40
30
41-80
24 81-100
18
Vibration
Unpackaged
5 Hz to 20 Hz: 0.01 g² Hz sloping up to 0.02 g² Hz
20 Hz to 500 Hz: 0.02 g² Hz (flat)
Packaged
5 Hz to 40 Hz: 0.015 g² Hz (flat)
40 Hz to 500 Hz: 0.015 g² Hz sloping down to 0.00015 g² Hz
2.7 Reliability
The Mean Time Between Failures (MTBF) prediction is calculated using component and subassembly random failure rates. The calculation is based on the Telcordia SR-332-2 Issue 2, Method I, Case 3, 55C ambient. The MTBF prediction is used to estimate repair rates and spare parts requirements. The MTBF for the board is 68,196 hours.
2.8 Environmental
Table 28 lists the environmental specifications for the board.
Table 28. Environmental Specifications
Note: Before attempting to operate this board, the overall temperature of the board must be above the minimum
operating temperature specified. It is recommended that the board temperature be at least room temperature before attempting to power on the board. The operating and non-operating environment must avoid condensing humidity.
54
3 Overview of BIOS Features
3.1 Introduction
The board uses an Intel Visual BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated using a disk-based program. The SPI Flash contains the Visual BIOS Setup program, POST, the PCI auto-configuration utility, LAN EEPROM information, GOP
(Graphics Output Protocol) video BIOS (VBIOS), and Plug and Play support. The initial production
BIOSs are identified as JYGLKCPX.86A.
The Visual BIOS Setup program can be used to view and change the BIOS settings for the computer, and to update the system BIOS. The BIOS Setup program is accessed by pressing the [F2] key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins.
NOTE
The maintenance menu is displayed only when the board is in configuration mode. Section 2.3 on page 48 shows how to put the board in configuration mode.
3.2 BIOS Flash Memory Organization
The Serial Peripheral Interface Flash Memory (SPI Flash) includes a 128 Mb (16384 KB) flash memory device.
3.3 System Management BIOS (SMBIOS)
SMBIOS is a Desktop Management Interface (DMI) compliant method for managing computers in a managed network.
The main component of SMBIOS is the Management Information Format (MIF) database, which contains information about the computing system and its components. Using SMBIOS, a system administrator can obtain the system types, capabilities, operational status, and installation dates for system components. The MIF database defines the data and provides the method for accessing this information. The BIOS enables applications such as third-party management software to use SMBIOS. The BIOS stores and reports the following SMBIOS information:
BIOS data, such as the BIOS revision level Fixed-system data, such as peripherals, serial numbers, and asset tags Resource data, such as memory size, cache size, and processor speed Dynamic data, such as event detection and error logging
Additional board information can be found in the BIOS under the second screen to the right of the Main BIOS page.
55
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
For information about
Refer to
BIOS update utilities
http://www.intel.com/support/motherboards/desktop/sb/CS-034499.htm
Media Type
(Note)
Can be used for BIOS recovery?
Hard disk drive (connected to SATA or USB)
Yes
CD/DVD drive (connected to USB)
Yes
USB flash drive
Yes
USB diskette drive (with a 1.4 MB diskette)
No (BIOS update file is bigger than 1.4 MB size limit)
3.4 Legacy USB Support
Legacy USB is not supported on Intel NUC Products NUC7CJY/NUC7PJY.
3.5 BIOS Updates
The BIOS can be updated using either of the following utilities, which are available on the Intel World Wide Web site:
Intel
Intel [F7] switch during POST allows a user to select where the BIOS .bio file is located and
Intel Visual BIOS allows the user to select the BIOS .bio file from a USB device or hard disk
All utilities verify that the updated BIOS matches the target system to prevent accidentally installing an incompatible BIOS.
®
Express BIOS Update utility, which enables automated updating while in the Windows environment. Using this utility, the BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a USB CD-ROM.
perform the update from that location/device. Similar to performing a BIOS Recovery without removing the BIOS configuration jumper.
drive.
NOTE
Review the instructions distributed with the upgrade utility before attempting a BIOS update.
3.5.1 Language Support
The BIOS Setup program and help messages are supported in US English. Check the Intel web site for support.
3.6 BIOS Recovery
It is unlikely that anything will interrupt a BIOS update; however, if an interruption occurs, the BIOS could be damaged. Table 29 lists the drives and media types that can and cannot be used for BIOS recovery. The BIOS recovery media does not need to be made bootable.
Table 29. Acceptable Drives/Media Types for BIOS Recovery
56
Overview of BIOS Features
For information about
Refer to
BIOS recovery
http://www.intel.com/support/motherboards/desktop/sb/CS-034524.htm
NOTE
Supported file systems for BIOS recovery:
NTFS (sparse, compressed, or encrypted files are not supported) FAT32 FAT16 FAT12 ISO 9660
3.7 Boot Options
In the BIOS Setup program, the user can choose to boot from a hard drive, optical drive, removable drive, or the network. The default setting is for the optical drive to be the first boot device, the hard drive second, removable drive third, and the network fourth.
NOTE
Optical drives are not supported by the onboard SATA connectors. Optical drives are supported only via the USB interfaces.
3.7.1 Network Boot
The network can be selected as a boot device. This selection allows booting from the onboard LAN or a network add-in card with a remote boot ROM installed.
Pressing the [F12] key during POST automatically forces booting from the LAN. To use this key during POST, the User Access Level in the BIOS Setup program's Security menu must be set to Full.
3.7.2 Booting Without Attached Devices
For use in embedded applications, the BIOS has been designed so that after passing the POST, the operating system loader is invoked even if the following devices are not present:
Video adapter Keyboard Mouse
3.7.3 Changing the Default Boot Device During POST
Pressing the [F10] key during POST causes a boot device menu to be displayed. This menu displays the list of available boot devices. Table 30 lists the boot device menu options.
57
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Boot Device Menu Function Keys
Description
[] or []
Selects a default boot device
[Enter]
Exits the menu, and boots from the selected device
[Esc]
Exits the menu and boots according to the boot priority defined through BIOS setup
Table 30. Boot Device Menu Options
3.7.4 Power Button Menu
The Power Button Menu is accessible via the following sequence:
1. System is in S4/S5 (not G3)
2. User pushes the power button and holds it down
3. The power LED will change to its secondary color to signal the user to release the power
button (approximately 3 seconds); alternately, the system will emit three short beeps from the PC speaker or headphones, if installed, then stop. Release immediately.
4. User releases the power button before the 4-second shutdown override.
If this boot path is taken, the BIOS will use default settings, ignoring settings in VPD where possible.
The BIOS will display the following prompt and wait for a keystroke:
[ESC] Normal Boot [F2] Intel Visual BIOS [F3] Disable Fast Boot [F4] BIOS Recovery [F7] Update BIOS [F10] Enter Boot Menu [F12] Network Boot
[F3] Disable Fast Boot is only displayed if at least one Fast Boot optimization is enabled.
If an unrecognized key is hit, then the BIOS will beep and wait for another keystroke. If one of the listed hotkeys is hit, the BIOS will follow the indicated boot path. Password requirements must still be honored.
If Disable Fast Boot is selected, the BIOS will disable all Fast Boot optimizations and reset the system.
58
Overview of BIOS Features
Password Set
Password During Boot
Neither
None
Master only
None
User only
User only
Master and User Set
Master or User
3.8 Hard Disk Drive Password Security Feature
The Hard Disk Drive Password Security feature blocks read and write accesses to the hard disk drive until the correct password is given. Hard Disk Drive Passwords are set in BIOS SETUP and are prompted for during BIOS POST. For convenient support of S3 resume, the system BIOS will automatically unlock drives on resume from S3. Valid password characters are A-Z, a-z, and 0-9. Passwords may be up to 19 characters in length.
The User hard disk drive password, when installed, will be required upon each power-cycle until the Master Key or User hard disk drive password is submitted.
The Master Key hard disk drive password, when installed, will not lock the drive. The Master Key hard disk drive password exists as an unlock override in the event that the User hard disk drive password is forgotten. Only the installation of the User hard disk drive password will cause a hard disk to be locked upon a system power-cycle.
Table 31 shows the effects of setting the Hard Disk Drive Passwords.
Table 31. Master Key and User Hard Drive Password Functions
During every POST, if a User hard disk drive password is set, POST execution will pause with the following prompt to force the user to enter the Master Key or User hard disk drive password:
Enter Hard Disk Drive Password:
Upon successful entry of the Master Key or User hard disk drive password, the system will continue with normal POST.
If the hard disk drive password is not correctly entered, the system will go back to the above prompt. The user will have three attempts to correctly enter the hard disk drive password. After the third unsuccessful hard disk drive password attempt, the system will halt with the message:
Hard Disk Drive Password Entry Error
A manual power cycle will be required to resume system operation.
NOTE
The passwords are stored on the hard disk drive so if the drive is relocated to another computer that does not support Hard Disk Drive Password Security feature, the drive will not be accessible.
59
Intel NUC Products NUC7CJY/NUC7PJY Technical Product Specification
Password Set
Supervisor Mode
User Mode
Setup Options
Password to Enter Setup
Password During Boot
Neither
Can change all options
(Note)
Can change all options
(Note)
None
None
None
Supervisor only
Can change all options
Can change a limited number of options
Supervisor Password
Supervisor
None User only
N/A
Can change all options
Enter Password Clear User Password
User
User
Supervisor and user set
Can change all options
Can change a limited number of options
Supervisor Password Enter Password
Supervisor or user
Supervisor or user
3.9 BIOS Security Features
The BIOS includes security features that restrict access to the BIOS Setup program and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup program and for booting the computer, with the following restrictions:
The supervisor password gives unrestricted access to view and change all the Setup options
in the BIOS Setup program. This is the supervisor mode.
The user password gives restricted access to view and change Setup options in the BIOS
Setup program. This is the user mode.
If only the supervisor password is set, pressing the <Enter> key at the password prompt of
the BIOS Setup program allows the user restricted access to Setup.
If both the supervisor and user passwords are set, users can enter either the supervisor
password or the user password to access Setup. Users have access to Setup respective to which password is entered.
Setting the user password restricts who can boot the computer. The password prompt will be
displayed before the computer is booted. If only the supervisor password is set, the computer boots without asking for a password. If both passwords are set, the user can enter either password to boot the computer.
For enhanced security, use different passwords for the supervisor and user passwords. Valid password characters are A-Z, a-z, and 0-9. Passwords may be up to 20 characters in
length.
To clear a set password, enter a blank password after entering the existing password.
Table 32 shows the effects of setting the supervisor password and user password. This table is for reference only and is not displayed on the screen.
Table 32. Supervisor and User Password Functions
Note: If no password is set, any user can change all Setup options.
60
Type
Pattern
Note
BIOS update in progress
Off when the update begins, then on for 0.5 seconds, then off for 0.5 seconds. The pattern repeats until the BIOS update is complete.
Video error
(Note)
On-off (1.0 second each) two times, then 2.5-second pause (off), entire pattern repeats (blink and pause) until the system is powered off.
When no video option ROM is found.
Memory error
On-off (1.0 second each) three times, then 2.5-second pause (off), entire pattern repeats (blinks and pause) until the system is powered off.
Thermal trip warning
Each beep will be accompanied by the following blink pattern: .25 seconds on, .25 seconds off, .25 seconds on, .25 seconds off. This will result in a total of 16 blinks.
Error Message
Explanation
CMOS Battery Low
The battery may be losing power. Replace the battery soon.
CMOS Checksum Bad
The CMOS checksum is incorrect. CMOS memory may have been corrupted. Run Setup to reset values.
Memory Size Decreased
Memory size has decreased since the last boot. If no memory was removed, then memory may be bad.
No Boot Device Available
System did not find a device to boot.
4 Error Messages and Blink Codes
4.1 Front-panel Power LED Blink Codes
Whenever a recoverable error occurs during POST, the BIOS causes the board’s front panel
power LED to blink an error message describing the problem (see Table 33).
Table 33. Front-panel Power LED Blink Codes
Note: Disabled per default BIOS setup option.
4.2 BIOS Error Messages
Table 34 lists the error messages and provides a brief description of each.
Table 34. BIOS Error Messages
61
Item from Figure 21
Description
Kensington* Anti-Theft Key Lock Hole SD Card Reader
Digital Microphone Array
Power Switch and Power LED
Speaker/Headset Jack
USB 3.0 Connectors
Consumer Infrared Sensor
5 Intel NUC Kit Features
5.1 Chassis Front Panel Features
Intel NUC Boards NUC7CJYB and NUC7PJYB can be found integrated into Intel® NUC Kit NUC7CJYH, Intel® NUC Kit NUC7PJYH, and Intel® NUC Mini PC NUC7CJYS. Figure 21 shows the location of the features located on or near the front of the chassis.
Figure 21. Intel NUC Products NUC7CJYH/NUC7PJYH/NUC7CJYS Features – Front
Table 35 lists the components identified in Figure 21.
Table 35. Components Shown in Figure 21
62
5.2 Chassis Rear Panel Features
Item from Figure 22
Description
19V DC Power Inlet
Cooling Vents
Speaker and Optical Audio Jack High Definition Multimedia Interface Connectors
Ethernet Port
USB 3.0 Connectors
Figure 22 shows the location of the features located on the rear of the chassis.
Intel NUC Kit Features
Figure 22. Intel NUC Products NUC7CJYH/NUC7PJYH/NUC7CJYS Features – Rear
Table 36 lists the components identified in Figure 22.
Table 36. Components Shown in Figure 22
63
Loading...