Insinkerator SS-100-1 Service Manual

PARTS LIST FOR COMMERCIAL DISPOSERS MODEL

SS-100 IN-SINK-ERATOR® 1 H.P.

(Includes Models SS-100-L, SS-100-2, SS-100-3)

ORDER BY PART NUMBER, NOT CODE NUMBER

(Minimum Parts Order $3.00)

(ALL PARTS F.O.B.FACTORY/DEPOT) (INCLUDE SERIAL AND MODEL NUMBER OF DISPOSER WHEN ORDERING)

PARTS LIST FOR COMMERCIAL DISPOSERS

No.

Reqd

IN-SINK-E

BATOR DIVISION

MODEL SS-100. IN-SINK-ERATOR® 1 H.P.

Code

No.

Part

No.
1 11004 1 Mounting Flange
2 11016 1 Gasket, Mounting

3 11020-A 1 Body, Container
4 1491 6 Bolt, Mounting
5 11227 1 Pipe Plug
6 11006 1 Seal, Body-Shredder
7 12442 1 Body and Cover Assembly
8 11252-A 1 Stationary Shredder
9 11260 1 Nut, Shredder

10 12445 1 Washer
11 12142 1 Washer, Fibre
12 12316 I Rotor Shredder
13 12327 1 Upper End Bell- Includes

14 12321 1 Face Seal
15 12318 1 Spacer Sleeve
16 12319 1 Centrifugal Moisture Shield
17 12610 1 Bearing Assembly - Upper
18 12326 1 Oil and Water Retainer
19 11322 2 Woodruff Key
20 12611

Codes 9-10-11.14-15-16-17-18-19
21 11444 3 Washer
22 1491 3 Bolt
23 1470 1 Washer, Tail Pipe
24 5487 1 Tail Pipe
25 1461 1 Flange - Tail Pipe
26 1468 2 Bolt - Tail Pipe
27 12330-B

28 1233I-B

230/460 Volt, 60 Cycle, Three Phase
29 1537 2 Spring - Centrifugal Switch
30 12348 1 Centrifugal Switch
31 7422 2 Screw
32 12393 1 Start Switch

No.

Reqd

Codes 14-16-17-18

Bearing - Seal Key Includes

Rotor & Shaft Assembly (Includes
Codes 29 & 30)
208 Volt, 60 Cycle, Single Phase S,
115/230 Volt, 60 Cycle, Single Phase
Rotor & Shaft Assembly
208 Volt, 60 Cycle, Three Phase &

(AIL PARTS F.O.B. FACTORY/DEPOT) (INCLUDE SERIAL AND MODEL NUMBER OF DISPOSER WHEN ORDERING)

(Includes Models SS-100-1, SS-100-2, SS-100-3)

Description

ORDER BY PART NUMBER, NOT CODE NUMBER

Code

No.

33 5765 2 Screw
34 12370 1 Shell - Trim
35 12351-G 1 Stator Assembly

36 12351-B 1 Stator Assembly

37 12549-8 1 Siator Assembly

38 12352-8 1 Stator Assembly

39 12433 1 Terminal Box Mounting Bracket -

40 12433-E 1 Terminal Box Mounting Bracket -

Three Phase
41 11448 4 Screw
42 12384 1 Bushing
43 11868 1 Capacitor - Single Phase Only
44 12389 1 Overload Protector

115/230 Volt, 60 Cycle, Single Phase
45 12391 1 Overload Protector

46 12378 1 Clamp, Overload
47 5765 2 Screw
48 12372 1 Terminal Box
49 12383 1 Grommet
50 12381 1 Screw
51 12415 1 Bearing - Lower
52 12399 1 Spring, Pre-load
53 12684 1 End Frame, Lower
54 12395 1 Fan
55 12635 I Retaining Ring
56 12490 3 Tube, Spacer
57 11940 3 Bolt, Thru
58 12396 1 Cover, Bottom
59 12586 2 Plug
60 11757-B 2 Leg (Optional)
61 12564 1 Ground Screw

(Minimum Parts Order $3.00)

Part

EFFECTIVE March, 1972

No.

208 Volt, 60 Cycle, Single Phase

115/230 Volt, 60 Cycle, Single Phase

208 Volt, 60 Cycle, Three Phase

230/460 Volt, 60 Cycle, Three Phase

Single Phase

208 Volt, 60 Cycle, Single Phase

208 Volt, 60 Cycle, Three Phase &
230/460 Volt, 60 Cycle, Three Phase

Description

Form No. C-I24-72C PRINTED IN U.S.A.

EMERSON ELECTRIC CO.
4700-21ST STREET RACINE.
WISCONSIN S3406 PHONE:
[phone]

COMMERCIAL DISPOSER

ISE

September, 1979

1

H.P.

IN-SINK-ERATOR

CANADIAN

MODEL MODEL

SS-100-8 115/230/60/1 SS-100-12
SS-100-9 208/60/1 SS-100-13
SS-100-10 230/460/60/3 SS-100-14
SS-100-11 208/60/3 SS-100-15

Start with Serial #70.000

(All Part F.O.B. Agency/Dept) (Include Serial and Model Number of Disposer when ordering)

ORDER BY PART NUMBER, HOT CODE NUMBER

SS-100-8 115/230/60/1

SS-100-12

1

1

1

1

1

1

1

1

1

1

1

1

1

1

I

SE

4173

11009

1124

IN-SINK-ERATOR DIVISION

CANADIAN

MODEL MODEL

SS-100-9 208/60/1 SS-100-13
SS-100-10 230/460/60/3 SS-100-14
SS-100-11 208/60/3 SS-100-15

Code

Port

No.

No.

1 11004
2 11016
3 11020-A
4 1491 6 Bolt, Mounting
5 11227
6 11006
7 12443
8 11252-A

9 11260
10 12445
11 0143 1 Washer, Fibre 41 1243 3-E 1 Terminal Box Mounting Bracket
12 13944
13 13081

14 12936 1 Shield 44 11868 1 Capacitor (Single Phase only)
15 13137 6 Screw 45 12389 1 Overload Protector
16 12934-A 1 Seal Assembly 208 Volt. 60 Hz. Single Phase
17 12935
18 13860
19 12319
20 12610 1 Bearing Assembly - Upper 230/460 Volt, 60 Hz, Three Phase
21 13326 1 Oil and Watt Retains 47 12378 1 Clamp. Overload
22 11322 3 Woodruff Key 48 5765 2 Screw
23 13080 1 Bearing Seal Kit, Includes Codes 9, 10 49 12372 1 Terminal Box

24 11444 3 Washer 51 12381 1 Screw
25 1491 3 Bolt 52 1241$ 1 Bearing, Lower
26 1470 1 Washer Tail Pipe 53 12399 1 Spring, Pre-load
27 5487 1 Toil Pipe 54 12684 1 End Frame, lower
28 1461 1 Range - Tail Pipe 55 123955 1 Fan
29 1460 2 Bolt - Tail Pipe 56 12635 1 Retaining Ring
30 12947-B 1 Rotor & Shaft Assembly 57 12490 3 Tube, Spacer

31 12954 1 Centrifugal Switch Assembly 61 11757-B 2 Leg (Optional)
32 12948-B 1 Rotor & Shaft Assembly

33 7433 2 Screw
34 13393 1 Start Switch 63 11930 1 Overload Protector
35 12370 1 Shell - Trim 208 Volt, 60 Hz, Single Phase

No.

Req.

Mounting Flange 36 130754 1 Stator Assembly
Gasket, Mounting
Body. Container 37 13075-0 1 Stator Assembly

Pipe Plug 38 13077-C 1 Stator Assembly
Seal. Body-Shredder
Body and Cover Assembly 39 13076-8 I Stator Assembly
Stationary Shredder
Nut. Shredder 40 13433 1 Terminal Box Mounting Bracket
Washer

Rotor Shredder
End Bell, Upper Includes Codes 42 11448 4 Screw
14 thru 21 43 12384 1 Bushing

Sleeve Spacer
0'Ring 46 12391 1 Overload Protector
Centrifugal Moisture Shield

11, 14, 15, 16, 17, 18, 19, 20, 21, 22 50 12383 1 Grommet

Includes Code #31 58 11940 3 Bolt, Thru
206 Volt, 60 Hz, Single Phase & 59 12396 1 Cover, Bottom
115/230 Volt, 60 Hz, Single Phone [phone] Ground Screw

208 Volt. 60 Hi, Three Phase
230/460, 60 Hi, Three Phase 62 12928 1 Overload Protector

Description Code No.

Part

No.

No.

Req.

115/230 Volt, 60 Hz, Single Phase

208 Volt, 60 Hz, Single Phase

230/460 Volt, 60 Hz, Three Phase

208 Volt, 60 Hz. Three Phase

Single Phase

Three Phase

115/230 Volt, 60 Hz, Single Phase

208 Volt, 60 Hz. Three Phase

115/230 Volt, 60 Hz. Single Phase

Description

CANADIAN ONLY

IN SINK ERATOR

SPLASH BAFFLE

SLEEVE GUARD

ORDER BY PART NUMBER. MOT CODE NUMBER

(All Parts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)

EMERSON ELECTRIC CO.
4700-21 ST STREET
RACINE. WISCONSIN 53406
PHONE: [phone]

JAM RELEASE BAR

PRINTED IN USA

IN

ERATOR

CODE

PART

NO.

CODE

PART

NO.

1 11004

1

Flange, Mounting

30

12947B

1

Rotor & Shaft Assembly

SINK

COMMERCIAL DISPOSER

MODEL No. SS100-16

(100 / 208 / Volt / 50/SOHz / 1 Phase) 1 H.P.

Start Date:

3/99

Engineer Number:

13025N

ORDER BY PART NUMBER, NOT CODE NUMBER

NO. NO. REQ. DESCRIPTION NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting (Includes Codes 31 & 47 )

3 11020A 1 Body Upper Assy 31 12954 1 Centrifugal Actuator

4 1491 6 Screw (1/4-20 x 3/4) 32 8221 2 Screw (8-32 x 1/2)

5 11227 1 Plug, Pipe 33 12393 1 Switch, Start

6 11006 1 Gasket, Shredder 34 12370 1 Trim Band

7 12442 1 Body & Cover Assy 35 1836A 2 Screw (8-32 x 1/2)

8 11252A 1 Shredder, Stationary 36 13075E 1 Stator Assy

9 11260 1 Nut 37 12433 1 Bracket Assy (Mounting)
10 12445 1 Washer 38 11448 4 Screw (8-18 x 1/4)
11 12142 1 Washer, Fiber 39 12384 1 Bushing
12 12944 1 Rotor Shredder Assy 40 11868 1 Capacitor
13 13081 1 Upper End Bell Assy 41 13422L 1 Overload Protector

(Includes Codes 14-22) 42 12378 1 Clamp, Overload
14 12936 1 Shield 43 8221 2 Screw (8-32 x 1/2)
15 1269 6 Screw (8-18 x 1/2) 44 13396 1 Box, Terminal Assy
16 12934A 1 Seal Assy (Includes Code 40)
17 12935 1 Sleeve, Spacer 45 12381 1 Screw (8-32 x 1-1/4)
18 12860 1 0-Ring 46 12383 1 Grommet, Overload
19 12319 1 Slinger 47 12415 1 Bearing, Lower
20 12610 1 Upper Bearing Assy 48 12399 1 Spring, Pre-load
21 12326 1 Water & Oil Seal 49 12684 1 End Frame, Lower
22 11322 3 Key. Woodruff 50 12395 1 Fan
23 13080 1 Kit, Bearing Seal 51 12635 1 Ring, Retaining

(Includes Codes 9-11 & 14-22) 52 12490 3 Tube, Spacer
24 11444 3 Washer, Lock 53 11940A 1 Bolt, Thru
25 3135 3 Screw (1/4-20x1) 54 12396 1 Cover, Bottom
26 1470 1 Gasket, Tailpipe 55 2466A 1 Screw, Ground
27 8219 1 Tailpipe 56 11757B 2 Tube, Foot Assembly
28 1461 1 Flange, Tailipe (Optional)
29 1468 2 Screw (1/4-20x1/2)

ISE

COMMERCIAL DISPOSER

May.

1985

1

H.P.

IN-SINK-ERATOR

(All Pans F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)

MODEL

SS-100-18 115/208/230/60/1
SS-100-19 208/230/460/60/3

ORDER BY PART NUMBER, NOT CODE NUMBER

IN

-

SINK

-

ERATOR

COMMERCIAL

DISPOSER

Start Date:

CODE

PART

NO. DESCRIPTION

CODE

PART

NO. DESCRIPTION

1 11004

1

Flange, Mounting

31

12954

1

Centrifugal Actuator

1

1

1

1

1

1

1

1

1

1

MODEL NO. SS100-20

CANADIAN (115/208-30/60/10)

7/87

Engineer Number

130858

0RDER BY PART NUMBER, NOTCODE NUMBER

NO. NO. REQ.

2 11016
3 11020-A
4 1491 6 Screw, Mounting 33 12393 1 Switch, Start

5 11227 1 Pipe Plug (Single Phase Only)
6 11006
7 12442
8 11252-A

9 11260
10 12445
11 12142
12 12944
13 13081

14 12936 1 Shield
15 1269 6 Screw, Tapping 41 13422-L 1 Overload, Protector
16 12934-A 1 Seal Assy (Single Phase)
17 12935 1 Sleeve, Spacer 42 12378 1 Clamp, Overload
18 12860 1 0-Ring 43 5765 2 Screw, Tapping
19 12319 1 Slinger 44 12372 1 Box, Terminal
20 12610 1 Bearing Assy, Upper 45 12381 1 Screw
21 12326 1 Seal, Water & Oil 46 12383 1 Grommet, Overload
22 11322 3 Key, Woodruff 47 12415 1 Bearing, Lower
23 13080 1 Bearing Seal Kit 48 12399 1 Washer, Spring

24 1)444 3 Washer, Lock 51 12635 1 Ring, Retaining
25 3135 3 Screw 52 12490 3 Tube, Spacer
26 1470 1 Gasket, Tailpipe 53 11940-A 3 Bolt, Thru
27 5487 1 Tailpipe 54 12396 1 Cover, Bottom
28 1461 1 Flange, Tailpipe 55 2466-A 1 Screw, Ground
29 1468 2 Screw, Tailpipe 56 11757-B 2 Tube Assy, Foot
30 12947-B 1 Rotor & Shaft Assy

(Incl. Codes 31 & 47)

Gasket, Mounting
Body Assy, Upper 32 8221 2 Screw

Gasket, Shredder 34 12370 1 Trim, Band
Body & Cover Assy 35 1836-A 2 Screw
Shredder, Stationary 36 13075-E 1 Stator Assy
Nut
Washer 37 12433 1 Bracket Assy
Washer, Fiber
Shredder Assy, Rotor 38 11448 4 Screw
End Bell Assy, Upper 39 12384 1 Bushing
(Incl. Codes 14 thru 22) 40 11868 1 Capacitor

(Incl. Codes 9-11 49 12684 1 End Frame, Lower
& 14 thru 22) 50 12395 1 Fan

(Single Phase)

NO. NO. REQ.

(Single Phase Only)

(Single Phase)
(Mounting) (Single Phase)

(Single Phase Only)

(Optional)

Start Date:

IN-SINK-ERATOR

COMMERCIAL DISPOSER

1 11004

1

Flange

, Mounting

29

1468 2 Screw, Tailpipe

1

1

1

1

1

1

MODEL NO. SS100-22

U.S.A.

(208-30/460/60/30)

7/87

Engineer Number

13385D

1 H.P.

ORDER BY PART NUMBER NOT

CODE

10 12445 1 Washer
11 12142 1 Washer, Fiber 35 11448 4 Screw
12 12944 1 Shredder Assy, Rotor 36 12384 1 Bushing
13 13081 1 End Bell Assy, Upper 37 13422-N 1 Overload, Protector

14 12936 1 Shield 38 12378 1 Clamp, Overload
15 1269 6 Screw, Tapping 39 5765 2 Screw, Tapping
16 12934-A 1 Seal Assy 40 12372 1 Box, Terminal
17 12935 1 Sleeve, Spacer 41 12381 1 Screw
18 12860 1 0-Ring 42 12383 1 Grommet, Overload
19 12319 1 Slinger 43 12415 1 Bearing, Lower
20 12610 1 Bearing Assy, Upper 44 12399 1 Washer, Spring
21 12326 1 Seal, Water & Oil 45 12684 1 End Frame, Lower
22 11322 3 Key, Woodruff 46 12395 1 Fan
23 13080 1 Bearing Seal Kit 47 12635 1 Ring, Retaining

24 11444 3 Washer, Lock 50 12396 1 Cover, Bottom
25 3135 3 Screw 51 2466-A 1 Screw, Ground
26 1470 1 Gasket, Tail pipe 52 11757-B 2 Tube Assy, Foot
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe

PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016
3 11020-A
4 1491 6 Screw, Mounting
5 11227
6 11006
7 12442
8 11252-A
9 11260 1 Nut 34 12433-E 1 Bracket, Terminal Box

Gasket, Mounting 30 12948-B 1 Rotor & Shaft Assy
Body Assy, Upper

Pipe Plug 31 12370 1 Trim, Band
Gasket, Shredder 32 1836-A 2 Screw
Body & Cover Assy 33 13077-C 1 Stator Assy
Shredder, Stationary

(IncI Codes 14 thru 22)

(IncI Codes 9.11 48 12490 3 Tube, Spacer
& 14 thru 22) 49 11940-A 3 Bolt. Thru

(Three Phase)
(IncI Code 43)

(Three Phase)
(Three Phase)

(Three Phase)

(Optional)

IN-SINK-ERATOR

1 11004

Flange, Mounting

29

1468 2 Screw, Tailpipe

2 11016

1

Gasket, Mounting

30

12948

-

B 1 Rotor & Shaft Assy

3

11020

-

A

1

Body Assy, Upper

(Three Phase)

4

1491 6 Screw, Mounting

(IncI. Code

43) 5 11227

1

Pipe Plug

31

12370

I

Trim, Band

6

11006

1

Gasket, Shredder

32

1836-A 2 Screw

7

12442

1

Body & Cover Assy

33

13077

-

C 1 Stator Assy

8 11252

-

A

1

Shredder, Stationary

(Three Phase)

9 11260

1

Nut 34 12433

-

E 1 Bracket, Terminal Box

10 12445

1

Washer

(Three Phase)

11 12142

1

Washer,

Fiber 35 11448

4

Screw

12

12944

1

Shredder Assy, Rotor

36

12384

1

Bushing

13

13081

1

End Bell Assy, Upper

37

13422

-

N 1 Overload, Protector

(IncI. Codes

14

thru

22)

(Three Phase)

14

12936

1

Shield

38

12378

1

Clamp, Overload

15

1269 6 Screw

, Tapping

39

5765 2 Screw, Tapping

16

12934

-

A 1 Seal Assy

40

12372

1

Box, Terminal

17

12935

1

Sleeve, Spacer

41

12381

1

Screw

18

12860

1

0-Ring 42 12383

1

Grommet, Overload

19

12319

1

Slinger

43

12415

1

Bearing, lower

20

12610

1

Bearing Assy, Upper

44

12399

1

Washer, Spring

21 12326

1

Seal, Water

&

Oil 45 12684

1

End Frame, Lower

22 11322

3

Key, Woodruff

46

12395

1

Fan 23 13080

1

Bearing Seal Kit

47

12635

1

Ring, Retaining

(IncI. Codes

9-11 48 12490

3

Tube, Spacer

& 14

thru

22) 49 11940-

A 3 Bolt, Thru

24

11444

3

Washer, Lock

50

12396

1

Cover, Bottom

25

3135 3 Screw

51

2466-A 1 Screw, Ground

26

1470 1 Gasket, Tailpipa

52

11757

-

B 2 Tube Assy, Foot

27

5487 1 Tailpipe

(Optional)

28 1461 1 Flange, Tailpipe

COMMERCIAL DISPOSER

MODEL NO. SS100-23

CANADIAN

(208-230/460/60/30)

Start Date:

7/87

Engineer Number:

13385E

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

ISE

1 11004

1

Flange, Mounting

27

12954

1

Centrifugal Actuator

1

29

1

1

31

2

1

1

36

1

12

1

37

2

6

40

1

1

42

1

1

46

1

22

3

47

1

3

50

3

25

3

51

1

26

1

52

2

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-24

(115/208/230 Volt/60HZ/1 Phase) 1 H.P.

Start Date:

03/90

Engineer Number

13385-0

Rev. 4/96

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting 28 8221 2 Screw (8-32x1/2)
3

4 1491 6 Screw (1/4-20x3/4) 30 12370 1 Trim Band
5

6 11006 1 Gasket, Shredder 32 13075-E 1 Stator Assy
7 12442 1 Assy, Body & Cover 33 12433 1 Bracket Assy

8

9 11260 1 Nut 34 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 35 11868 1 Capacitor
11

13 13597 1 Assy, Upper End Bell 38 13396-E 1 Box, Terminal Assy
14 12936 1 Shield 39 12381 1 Screw (8-32x1-1/4)

15
16 12934-A 1 Assy, Seal 41 13422BB 1 Overload Protector

17
18 12860 1 0-Ring 43 2466-A 1 Screw, Ground

19 12319 1 Slinger 44 12415 1 Bearing, Lower
20 12610 1 Bearing Assy, Upper 45 12399 1 Spring, Pre Load
21

23 13080 1 Kit, Bearing Seal (Incl. 48 12635 1 Ring, Retaining
24

11020-A

11227

11252-A

12142
13586

1269

12935

12326
11322

11444

3135

13592

Body, Assy, Upper
Plug, Pipe

Shredder, Stationary

Washer, Fiber
Assy, Rotor Shredder

(Incl. Codes 14 - 22)

Screw (8-18x1/2)
Sleeve, Spacer

Seal, Water & Oil
Key, Woodruff

codes 9-11 &14-22) 49 12490 3 Tube, Spacer
Washer, Lock
Screw (1/4-20x1)
Rotor & Shaft A\ssy.
(Incl. Codes 27 & 42)

12393

1836-A

12378

5765

13559
12384

12684
12395

11940-A

12396

11757-B

Switch, Start
Screw (8-32x1/2)

(Mounting)

Clamp, Overload
Screw (8-32x1/2)

(Incl. code 41)

Grommet, Overload
Bushing

End Frame, Lower
Fan

Bolt, Thru
Cover, Bottom
Tube, Foot Assy.
(Optional)

ENVIROVAC

CODE

PART

NO.

DESCRIPTION

CODE

PART NO.

NO.

DESCRIPTION

12

13566

Tube, Foot Assy.

COMMERCIAL DISPOSER

MODEL NO. SS100-25

(208/230/460 Volt/60 Hz/3 Phase) 1 H.P.

Start Date:

08/90

Engineer Number

13385-H

Rev. 1/96

ORDER BY PART NUMBER, NOT CODE NUMBER

1 11004 1 Flange, Mounting 25 3135 3 Screw (1/4-20x1)

2 11016 1 Gasket, Mounting 26 13592-A 1 Rotor & Shaft Assy.

3 11020-A 1 Body, Assy, Upper

4 1491 6 Screw (1/4-20x3/4) 27 12370 1 Trim Band

5 11227 1 Plug, Pipe 28 1836-A 2 Screw (8-32x1/2)

6 11006 1 Gasket, Shredder 29 13714-B 1 Stator Assy

7 12442 1 Assy, Body & Cover 30 12433-E 1 Bracket Assy (Mounting)

8 11252-A 1 Shredder, Stationary 31 11448 4 Screw (8-18x1/4)

9 11260 1 Nut 32 12378 1 Clamp, Overload

10

11 12142 1 Washer Fiber 34 13396 1 Box, Terminal Assy
13
14 12936 1 Shield 37 13422BD 1 Overload Protector

15 1269 6 Screw (8-18x1/2) 38 12384 1 Bushing
16 12934-A 1 Assy, Seal 39 2466-A 1 Screw, Ground
17 12935 1 Sleeve, Spacer 40 13709 1 Bearing, Lower
18 12860 1 0-Ring 41 13678 1 Spring, Pre-load
19 12319 1 Slinger 42 12684 1 End Frame, Lower
20 12610 1 Assy, Upper Bearing 43 12395 1 Fan
21 12326 1 Seal, Water & Oil 44 13677 1 Ring, Retaining
22 11322 3 Key, Woodruff 45 12490 3 Tube, Spacer
23 13080 1 Kit, Bearing Seal 46 12396 1 Cover, Bottom

24 11444 3 Washer, Lock 48 11757-B 2

12445 1 Washer 33 8221 2 Screw (8-32x1/2)

13586 1

Assy, Rotor Shredder

1 Assy, Upper End Bell 35 12381 1 Screw (8-32x1-1/4)

(lncl.Codes14.22) 36 12383 1 Grommet, Overload

(lncl. codes9-11&14-22) 47 11940-A 3 Bolt, Thru

(Ind. Codes 40)

(Inc), code 36)

ISE

IN-SINK-ERATOR

COMMERCIAL DINPOSEDR

09/09/92

13660

1 11004

1

Flange, Mounting

31

13708

1

Centrifugal Actuator

MODEL NO. SS100-28

(115/208/230 Volt / 60Hz /1 Phase)

Engineer Number:

1H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

2 11016 1 Gasket, Mounting 32 8221 2 Screw (8-32x1/2)
3 11020-A 1 Body. Assy, Upper 33 13707 1 Switch, Start
4 1491 6 Screw (1/4-20x3/4) 34 12370 1 Trim Band
5 11227 1 Plug, Pipe 35 1836-A 2 Screw(8-32x1/2)
6 11006 1 Gasket, Shredder 36 13713-B 1 Stator Assy
7 12442 1 Assy, Body & Cover 37 12433 1 Bracket Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut 38 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 39 12384 1 Bushing
11 12142 1 Washer, Fiber 40 11868 1 Capacitor
12 12944 1 Assy, Rotor Shredder 41 13422-E 1 Overload Protector
13 13722 1 Assy, Upper End Bell 42 12378 1 Clamp, Overload

(lncl.Codes14-22) 43 8221 2 Screw (8-32x1/2)
14 12936 1 Shield 44 13396 1 Box, Terminal Assy
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Assy, Seal 45 12381 1 Screw (8-32X1-1/4)
17 12935 1 Sleeve,Spacer 46 12383 1 Grommet, Overload
18 12860 1 0-Ring 47 13709 1 Bearing,Lower
19 12319 1 Slinger 48 13678 1 Spring, Pre-load
20 12610 1 Assy, Upper Bearing 49 13710 1 End Frame, Lower
21 12326 1 Seal, Water & Oil 50 13676 1 Fan
22 11322 3 Key, Wood ruff 51 13677 1 Ring, Retaining
23 13080 1 Kit. Bearing Seal (Incl. 52 12490 3 Tube,Spacer

codes 9-11& 14-22) 53 11940-A 3 Bolt, Thru
24 11444 3 Washer, Lock ' 54 12396 1 Cover, Bottom
25 3135 3 Screw(1/4-20x1) 55 2466-A 1 Screw, Ground
26 1470 1 Gasket, Tailpipe 56 11757-B 2 Tube, Foot Assy.
27 5487 1 Tailpipe
28 1461 1 Flange, Tail pipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-B 1 Rotor & Shaft Assy.

(Incl. Codes 31 & 47)

(Mounting)

(Incl. code 46)

(Optional)

1 11004

1

Flange, Mounting

28

1461 1 Flange, Tailpipe

codes

9-10-11 & 14

thru

ISE

13660

-

A

1

H.P.

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-29

(208/230/460Volt / 60H2 / 3 Phase)

Start Date:

09-01-92

Engineer Number:

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting 29 1468 2 Screw (1/4-20x1/2)
3 11020-A 1 Body, Assy, Upper 30 13674-H 1 Rotor & Shaft Assy
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug 31 12370 1 Trim, Band
6 11006 1 Gasket, Shredder 32 1836-A 2 Screw (8-32x1/2)
7 12442 1 Body & Cover Assy 33 13714-B 1 Staler Assy
8 11252-A 1 Shredder, Stationary 34 12433-E 1 Bracket Assy

9 11260 1 Nut
10 12445 1 Washer 35 11448 4 Screw (8-18x1/4)
11 12142 1 Washer, Fiber 36 12384 1 Bushing
12 12944 1 Shredder Assy, Rotor 37 13422-N 1 Overload, Protector
13 13722 1 End Bell Assy, Upper 38 12378 1 Clamp, Overload

14 12936 1 Shield 40 13396 1 Box, Terminal
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy 41 12381 1 Screw (8-32x1-1/4)
17 12935 1 Sleeve, Spacer 42 12383 1 Grommet, Overload
18 12860 1 0-Ring 43 13709 1 Bearing, Lower
19 12319 1 Slinger 44 13678 1 Spring, Pre-load
20 12610 1 Bearing Assy, Upper 45 13747 1 End Frame, Lower
21 12326 1 Seal, Waters Oil 46 13676 1 Fan
22 11322 3 Key, Woodruff 47 13677 1 Ring, Retaining
23 13080 1 Bearing Seal Kit (Incl. 48 12490 3 Tube, Spacer

24 11444 3 Washer, Lock 50 12396 1 Cover. Bottom
25 3135 3 Screw (1/4-20x1/2) 51 2466-A 1 Screw, Ground
26 1470 1 Gasket, Tailpipe 52 11757-B 2 Tube Assy, Foot
27 5487 1 Tailpipe (Optional)

(Incl. Codes 14 thru 22) 39 8221 2 Screw (8-32x1/2)

49 11940-A 3 Bolt, Thru-

(Incl. Code 43)

(Mounting)

(Incl. code 42)

ISE

1 11004

1

Flange, Mounting

31

13708

1

Centrifugal Actuator

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-30 (C.S.A.)

(115/208/230 Volt / 60Hz /1 Phase)

Start Data:

02/26/93

Engineer Number:

13660-B

1 H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting 32 8221 2 Screw (8-32x1/2)
3 11020-A 1 Body, Assy, Upper 33 13707 1 Switch, Start
4 1491 6 Screw (1/4-20x3/4) 34 12370 1 Trim Band
5 11227 1 Plug, Pipe 35 1836-A 2 Screw (8-32x1/2)
6 11006 1 Gasket, Shredder 36 13713-B 1 Stator Assy
7 12442 1 Assy, Body & Cover 37 12433 1 Bracket Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut 38 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 39 12384 1 Bushing
11 12142 1 Washer, Fiber 40 11868 1 Capacitor
12 12944 1 Assy, Rotor Shredder 41 13422-E 1 Overload Protector
13 13722 1 Assy, Upper End Bell 42 12378 1 Clamp, Overload

(lncl.Codes14.22) 43 8221 2 Screw (8-32x1/2)
14 12936 1 Shield 44 13396 1 Box, Terminal Assy
15 1269 6 Screw (8-18x1/2) (Incl. code 46)
16 12934-A 1 Assy, Seal 45 12381 1 Screw (8-32x1-1/4)
17 12935 1 Sleeve, Spacer 46 12383 1 Grommet, Overload
18 12860 1 0-Ring 47 13709 1 Bearing, Lower
19 12319 1 Slinger 48 13678 1 Spring, Pre-load
20 12610 1 Assy, Upper Bearing 49 13710 1 End Frame, Lower
21 12326 1 Seal, Water & Oil 50 13676 1 Fan
22 11322 3 Key, Woodruff 51 13677 1 Ring, Retaining
23 13080 1 Kit, Bearing Seal (Incl. 52 12490 3 Tube, Spacer

Codes 9-11 &14-22) 53 11940-A 3 Bolt, Thru
24 11444 3 Washer, Lock 54 12396 1 Cover, Bottom
25 3135 3 Screw (1/4-20xl) 55 2466-A 1 Screw, Ground
26 1470 1 Gasket, Tailpipe 56 11757-B 2 Tube, Foot Assy.
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-B 1 Rotor & Shaft Assy.

(Incl. Codes 31 & 47)

(Mounting)

(Optional)

ISE

27 5487 1 Tailpipe

(Optional)

1

H.P.

IN-SINK-ERATOR

COMMERCIAL DISPOSER

MODEL NO. SS100-31 (C.S.A.)

(208/230/460VoK / 60Hz / 3 Phase)

Start Date:

02/26/93

Engineer Number:

13660-C

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

1 11004 1 Flange, Mounting 28 1461 1 Flange, Tailpipe
2 11016
3 11020-A
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug 31 12370 1 Trim, Band
6 11006
7 12442
8 11252-A

9 11260
10 12445
11 12142 1 Washer, Fiber 36 12384 1 Bushing
12 12944 1 Shredder Assy, Rotor 37 13422-N 1 Overload, Protector
13 13722 1 End Bell Assy, Upper 38 12378 1 Clamp, Overload

14 12936 1 Shield 40 13396 1 Box, Terminal
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy 41 12381 1 Screw (8-32x1-1/4)
17 12935 1 Sleeve, Spacer 42 12383 1 Grommet, Overload
18 12860 1 O-Ring 43 13709 1 Bearing, Lower
19 12319 1 Slinger 44 13678 1 Spring, Pre-load
20 12610 1 Bearing Assy, Upper 45 13747 1 End Frame, Lower
21 12326 1 Seal, Water& Oil 46 13676 1 Fan
22 11322 3 Key, Woodruff 47 13677 1 Ring, Retaining
23 13080 1 Bearing Seal Kit (Incl. 48 12490 3 Tube, Spacer

codes 9-10-11 & 14 thru 22) 49 11940-A 3 Bolt, Thru
24 11444 3 Washer, Lock 50 12396 1 Cover, Bottom
25 3135 3 Screw (1/4-20x1/2) 51 2466-A 1 Screw, Ground
26 1470 1 Gasket, Tailpipe 52 11757-B 2 Tube Assy, Foot

1

Gasket, Mounting 29 1468 2 Screw (1/4-20x1/2)

1

Body, Assy, Upper 30 13674-H 1 Rotor & Shaft Assy

1

Gasket, Shredder 32 1836-A 2 Screw (8-32x1/2)

1

Body & Cover Assy 33 13714-B 1 Stator Assy

1

Shredder, Stationary 34 12433-E 1 Bracket Assy

1

Nut

1

Washer 35 11448 4 Screw (8-18x1/4)

(Incl. Codes 14 thru 22) 39 8221 2 Screw (8-32x1/2)

(Incl. Code 43)

(Mounting)

(Incl. code 42)

ENVIROVAC

COMMERCIAL DISPOSER

MODEL NO. SS100-32

Start Date:

1

1

1

1

1

1

1

(115/208/230 Volt / 50/SOHz /1 Phase)

Engineer Number:

13660-D

1H.P.

02/19/93

CODE PART NO.

NO. NO. REQ. DESCRIPTION NO. NO. REQ. DESCRIPTION

1 11004
2 11016
3 11020-A
4 1491 6 Screw (1/4-20x3/4)
5 11227
6 11000
7 12442
8 11252-A

9 11260 1 Nut 38 13396-E 1 Box, Terminal Assy
10 12445 1 Washer
11 12142 1 Washer, Fiber 39 12381 1 Screw (8-32x1-1/4)
12 13586 1 Assy, Rotor Shredder 40 13559 1 Plug, Button
13 13597-A 1 Assy, Upper End Bell 41 13422-BB 1 Overload Protector

14 12936 1 Shield 43 2466-A 1 Screw, Ground
15 1269 6 Screw (8-18x1/2) 44 13709 1 Bearing, Lower
16 12934-A 1 Assy, Seal 45 13678 1 Spring, Pre-load
17 12935 1 Sleeve, Spacer 46 13710 1 End Frame, Lower
18 12860 1 0-Ring 47 13676 1 Fan
19 12319 1 Slinger 48 13677 1 Ring, Retaining
20 12610 1 Assy, Upper Bearing 49 12490 3 Tube, Spacer
21 12326 1 Seal, Water & Oil 50 12396 1 Cover, Bottom
22 11322 3 Key. Woodruff 51 11940-A 3 Bolt, Thru
23 13080 1 Kit. Bearing Seal (Ind. 52 11757-B 2 Tube, Foot Assy.

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 13592-C 1 Rotor & Shaft Assy.

27 1370S 1 Centrifugal Actuator
28 8221 2 Screw (8-32x1/2)
29 13707 1 Switch, Start
30 12370 1 Trim Band

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE PART NO.

Flange, Mounting 31 1836-A 2 Screw (8-32x1/2)
Gasket, Mounting 32 13713-B 1 Stator Assy
Body, Assy, Upper 33 12433 1 Bracket Assy

Rug, Pipe 34 11448 4 Screw (8-18x1/4)
Gasket, Shredder 35 11868 1 Capacitor
Assy, Body & Cover 36 12378 1 Clamp, Overload
Shredder, Stationary 37 8221 2 Screw (8-32x1/2)

(Incl. Coda* 14-22) 42 12384 1 Bushing

Codes 9-11 & 14-22)

(Incl. Codes 27 & 44)

(Mounting)

(Incl. code 40)

(Optional)

ENVIROVAC

13660

-

G

1

1

35

1

1

37

1

40

1

6

43

1

1

46

1

2

29

13714

-

B 1 Stator

Assy

COMMERCIAL DISPOSER

MODEL NO. SS100-34

1 YR (208/230/380 Volt / 50 Hz / 3 Phase) 1 H.P.
FULL WRNTY

Start Date:

02/19/93

Engineer

Number

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

NO.

1 11004 1 Flange, Mounting 30 12433-P 1 Bracket Assy
2
3 11020-A 1 Upper Body Assy 31 11448 4 Screw (8-18x1/4)
4 1491 6 Screw (1/4-20x3/4) 32 12378 1 Clamp, Overload
5 11227 1 Plug, Pipe 33 8221 2 Screw (8-32x1/2)
6 11006 1 Gasket. Shredder 34 13396-E 1 Box, Terminal Assy
7 12442 1 Body & Cover Assy
8
9 11260 1 Nut 36 13559 1 Grommet, Overload

10
11 12142 1 Washer, Fiber 38 12384 1 Bushing
12 13588 1 Rotor Shredder Assy 39 2466-A 1 Screw, Ground
13

14 12936 1 Shield 42 13747 1 End Frame, Lower
15
16 12934-A 1 Seal Assy 44 13677 1 Ring, Retaining
17 12935 1 Sleeve, Spacer 45 12490 3 Tube, Spacer
18
19 12319 1 Slinger 47 11940-A 3 Bolt, Thru
20 12322 1 Upper Bearing Assy 48 11757-B 2 Tube, Foot Assy.
21 12326 1 Seal. Water & Oil
22 11322 3 Key, Woodruff
23 13080-A 1 Kit, Bearing Seal

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 13592-E 1 Rotor & Shaft Assy.

27 12370 1 Trim Shell
28

PART

NO.

11016

11252-A

12445

13928

NO.

REQ.

13919

12860

1836-A

DESCRIPTION

Gasket, Mounting

CODE

NO.

Shredder, Stationary

Washer

Upper End Bell Assy
(lncl.Codes14.22) 41 13678 1 Spring, Pre-load

Screw (8-18x1/2)

0-Ring

PART

NO.

12381

13422-BE 1 Overload Protector

13709

13676

12396

NO.

REQ.

(Mounting)

(Incl. code 36)
Screw (8-32x1-1/4)

Bearing, Lower

Fan

Cover, Bottom

(Optional)

DESCRIPTION

(lncl. Codes 9-11&14-22)

(Incl. Codes 40)

Screw (8-32x1/2)

Start date:

ISE

COMMERCIAL DISPOSER

13660

-

H

1

1

1

1

1

1

1

IN-SINK-ERATOR

MODEL NO. SS100-35 (EXPORT)

(100 Volt / 50/60Hz /1 Phase)

04/21/93

Engineer
Number

1 H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

1 11004 1 Flange, Mounting 31 14131 1 Centrifugal Actuator
2 11016 1 Gasket, Mounting 32 8221 2 Screw (8-32x1/2)

3 11020-A 1 Body, Assy, Upper 33 13707 1 Switch, Start
4 1491 6 Screw (1/4-20x3/4) 34 12370 1 Trim Band
5 11227
6 11006
7 12442
8 11252-A

9 11260 1 Nut 38 11448 4 Screw (8-18x1/4)
10 12445
11 12142

12 12944 1 Assy, Rotor Shredder 41 8221 2 Screw (8-32x1/2)
13 13722

14 12936
15 1269 6 Screw (8-18x1/2) 44 12383 1 Grommet, Overload
16 12934-A
17 12935
18 12860
19 12319 1 Slinger 48 13709 1 Bearing, Lower
20 12610 1 Assy, Upper Bearing 49 13678 1 Spring, Pre-load
21 12326 1 Seal, Water & Oil 50 13710 1 End Frame, Lower
22 11322 3 Key. Woodruff 51 13676 1 Fan
23 13080 1 Kit, Bearing Seal (Incl. 52 13677 1 Ring, Retaining

24 11444 3 Washer, Lock 54 12490 3 Tube, Spacer
25 3135 3 Screw (1/4-20x1) 55 12396 1 Cover, Bottom
26 1470 1 Gasket, Tailpipe 56 11757-B 2 Tube, Foot Assy.
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-8 1 Rotor & Shaft Assy.

Plug, Pipe 35 1836-A 2 Screw (8-32x1/2)
Gasket, Shredder 36 13713-B 1 Stator Assy
Assy, Body & Cover 37 12433 1 Bracket Assy
Shredder, Stationary

Washer 39 11868 1 Capacitor
Washer. Fiber 40 12378 1 Clamp, Overload

Assy, Upper End Bell 42 13396 1 Box, Terminal Assy
(Incl. Codes 14-22)
Shield 43 12381 1 Screw (8-32x1-1/4)

Assy, Seal 45 13422-T 1 Overload Protector
Sleeve, Spacer 46 12384 1 Bushing
0-Ring 47 2466-A 1 Screw, Ground

Codes 9-11 & 14-22) 53 11940-A 3 Bolt, Thru

(Incl. Codes 31 & 48)

(Mounting)

(Incl. code 48)

(Optional)

ENVIROVAC

Start Date:

1 11

004 1 Flange, Mounting

30

12433

-E 1

Bracket Assy

13422

-

COMMERCIAL DISPOSER

MODEL NO. SS100-36

(460 Volt / 60 Hz / 3 Phase)

11/29/93

Engineer Number:

13660-J

1 H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

2 11016 1 Gasket, Mounting
3 11020-A
4 1491 6 Screw (1/4-20x3/4) 32 12378 1 Clamp, Overload
5 11227 1 Plug, Pipe 33 8221 2 Screw (8-32x1/2)
6 11006 1 Gasket, Shredder 34 13396-E
7 12442 1 Assy, Body & Cover
8 13798 1 Shredder, Stationary 35 12381 1 Screw (8-32x1-1/4)

9 11260 1 Nut 36 12383 1 Grommet, Overload
10 12445 1 Washer 37
11 12142 1 Washer, Fiber 38 12384 1 Bushing
12 13799 1 Assy, Rotor Shredder 39 2466 -A 1 Screw, Ground
13 13597-A

14 12936 1 Shield 42 13710 1 End Frame, Lower
15 1269 6 Screw (8-18x1/2) 43 13676 1 Fan
16 12934-A
17 12935 1 Sleeve, Spacer 45 12490 3 Tube, Spacer
18 12860 1 O-Ring 46 12396 1 Cover, Bottom
19 12319 1 Slinger 47 11940-A
20 12610 1 Assy, Upper Bearing 48 11757-B
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Kit, Bearing Seal (Incl.

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 13592-E

27 12370 1 Trim Band
28 1836-A 2 Screw (8-32x1/2)
29 13657^J 1 Stator Assy

PART

NO.

1 Body, Assy, Upper 31 11448 4 Screw (8-18x1/4)

1 Assy, Upper End Bell 40 13709 1 Bearing, Lower

(Incl. Codes 14-22) 41 13678 1 Spring, Pre-load

1 Assy, Seal 44 13677 1 Ring, Retaining

Codes 9-11 & 14-22)

1 Rotor & Shaft Assy.

(Incl. Codes 40)

DESCRIPTION

CODE

PART

NO.

(Mounting)

1 Box, Terminal Assy

(Incl. code 36)

1 Overload Protector

3 Bolt, Thru
2 Tube, Foot Assy

(Optional)

DESCRIPTION

ENVIROVAC

NO.

NO.

REQ.

NO.

NO.

REQ.

1

1

1

1

1

1

COMMERCIAL DISPOSER

MODEL NO. SS100-37

(380 Volt / 50 Hz / 3 Phase)

Start Date:

11/29/93

Engineer Number:

13660-K

1 H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

1 11004 1 Flange, Mounting 30 12433-E 1 Bracket Assy
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper 31 11448 4 Screw(8-18x1/4)
4 1491 6 Screw (1/4-20x3/4) 32 12378 1 Clamp, Overload
5 11227 1 Plug, Pipe 33 8221 2 Screw (8-32x1/2)
6 11006 1 Gasket, Shredder 34 13396 1 Box, Terminal Assy
7 12442 1 Assy, Body & Cover
8 13803

9 11260
10 12445
11 12142
12 13799
13 13671 -L

14 12936 1 Shield 42 13710 1 End Frame, Lower
15 1269 6 Screw (8-18x1/2) 43 13676 1 Fan
16 12934-A 1 Assy, Seal 44 13677 1 Ring, Retaining
17 12935 1 Sleeve, Spacer 45 12490 3 Tube, Spacer
18 12860 1 0-Ring 46 12396 1 Cover, Bottom
19 12319 1 Slinger 47 11940-A 3 Bolt, Thru
20 12610 1 Assy, Upper Bearing 48 11757-B 2 Tube, Foot Assy.
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Kit, Bearing Seal (Incl.

24 11444 3 Washer, Lock
25 3135 3 Screw( 1/4-20x1)
26 13592-E 1 Rotor & Shaft Assy.

27 12370 1 Trim Band
28 1836-A 2 Screw (8-32x1/2)
29 13657-J 1 Stator Assy

PART

NO.

Shredder, Stationary 35 12381 1 Screw(8-32x1-1/4)
Nut 36 12383 1 Grommet, Overload
Washer 37 13422-BE 1 Overload Protector
Washer, Fiber 38 12384 1 Bushing
Assy, Rotor Shredder 39 2466-A 1 Screw, Ground
Assy, Upper End Bell 40 13709 1 Bearing, Lower
(lncl.Codes14.22) 41 13678 1 Spring, Pre-load

Codes 9-11 &14-22)

(Incl. Codes 40)

DESCRIPTION

CODE

PART

NO.

(Mounting)

(Incl. code 36)

(Optional)

DESCRIPTION

ENVIROVAC

13660

-

L

1 11004

1

Flange, Mounting

28

8221 2 Screw

(8-32x1/2)

COMMERCIAL DISPOSER

MODEL No. SS100-38

1-YR (115/208/230 Volt /60Hz / 1 Phase)

FULL WRNTY 1 H.P.

Start Data:

01/96

Engineer Number:

Rev: 01/99

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

NO.

PART NO.

2 11016 1 Gasket, Mounting 29 13707 1 Switch, Start
3 11020-A 1 Body Upper Assy 30 12370 1 Trim Band
4 1491 6 Screw (1/4-20x3/4) 31 1836-A 2 Screw (8-32 x 1/2)
5 11227 1 Plug, Pipe 32 13656-B 1 Stator Assy
6 11006 1 Gasket, Shredder 33 12433 1 Bracket Assy (Mounting)
7 12442 1 Body & Cover Assy 34 11448 4 Screw (8-18x1/4)
8 11252-A 1 Shredder, Stationary 35 11868 1 Capacitor

9 13952 1 Nut 36 12378 1 Clamp, Overload
10 13987 1 Washer 37 8221 2 Screw (8-32 x 1/2)
11 12142 1 Washer, Fiber 38 13396-E 1 Box, Terminal Assy
12 13586 1 Rotor Shredder Assy (Includes Code 40)
13 13597-C 1 Upper End Bell Assy 39 12381 1 Screw (8-32x1-1/4)
14 12936 1 Shield 40 13559 1 Plug, Button
15 13919 6 Screw (#10-24 x 3/8PH) 41 13422-BB 1 Overload Protector
16 12934-A 1 Seal Assy 42 12384 1 Bushing
17 12935 1 Sleeve, Spacer 43 2466-A 1 Screw, Ground
18 12860 1 0-Ring 44 13709 1 Bearing, Lower
19 12319 1 Slinger 45 13678 1 Spring, Pre-load
20 12610 1 Upper Bearing Assy 46 13710 1 End Frame, Lower
21 12326 1 Water & Oil Seal 47 13676 1 Fan
22 11322 3 Key, Woodruff 48 13677 1 Ring, Retaining
23 13080-A 1 Kit, Bearing Seal 49 12490 3 Tube, Spacer

24 11444 3 Washer, Lock 51 11940-A 3 Bolt, Thru
25 3135 3 Screw (1/4-20x1) 52 11757-B 2 Tube, Foot Assembly
26 13592-C 1 Rotor & Shaft Assembly (Optional)

(Includes Codes 27 & 44)

27 13708 1 Centrifugal Actuator

NO.

REQ.

DESCRIPTION

(Includes Codes 9-11 & 14-22) 50 12396 1 Cover, Bottom

CODE

NO.

PART NO.

NO.

REQ.

DESCRIPTION

ENVIROVAC

1 11004

1

Flange, Mounting

25

3135 3 Screw

(1/4-20x1)

1

26

1

6

27

1

1

29

1

1

31

4

9

1

32

1

10

1

33

2

1

13

1

35

1

36

1

6

38

1

16

1

39

1

17

1

40

1

18

1

41

1

19

1

42

1

20

1

43

1

21

1

44

1

22

3

45

3

3

48

2

COMMERCIAL DISPOSER

MODEL NO. SS100-39

1 FULL (208/230/460 Volt / 60 Hz / 3 Phase)

YR WRNTY 1 H.P.

Start Date:

01/96

Engineer Number

13660-M

Rev. 8/01/96

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

NO.

2

PART NO.

3 11020-A 1 Body Assy, Upper

4

5 11227 1 Plug, Pipe 28 1836-A 2 Screw (8-32x1/2)

6

7 12442 1 Body & Cover Assy 30 12433-E 1 Bracket Assy (Mounting)

8

11 12142 1 Washer, Fiber 34 13396-E 1 Box, Terminal Assy
12

14 12936 1 Shield 37 13422-BD 1 Overload Protector
15

23 13080-A 1 Bearing Seal Kit 46 12396 1 Cover, Bottom

11016

1491

11006

11252-A

11260
12445

13586
13928

13919

12934-A

12935
12860
12319
12322
12326
11322

24

11444

NO.

REQ.

Gasket, Mounting

Screw (1/4-20x3/4)

Gasket, Shredder

Shredder, Stationary
Nut
Washer

Rotor Shredder Assy
Upper End Bell Assy

Screw (#10-24 x 3/8")
Seal Assy
Sleeve, Spacer
0-Ring
Slinger
Upper Bearing Assy
Seal, Water & Oil
Key, Woodruff

Washer, Lock

DESCRIPTION

CODE

NO.

PART NO.

13592-D

NO.

REQ.

Rotor & Shaft Assy

12370

13714-B

11448
12378

8221

(lncl. Codes 14-22)

(Incl. codes 9-11 &14.22) 47 11940-A 3 Bolt, Thru

12381
13559

12384

2466-A

13709
13678
13747
13676
13677
12490

11757-B

Trim Band

Stator Assy

Screw (8.18x1/4)
Clamp, Overload
Screw (8-32x1/2)

Screw (8-32x1-1/4)
Grommet, Overload

Bushing
Screw, Ground
Bearing, Lower
Spring, Pre-load
End Frame, Lower
Fan
Ring, Retaining
Tube, Spacer

Tube, Foot Assy.

DESCRIPTION

(Incl. Codes 40)

(Incl. code 36)

(Optional)

ENVIROVAC

1 11004

1

Flange, Mounting

26

13592

-E 1

Rotor & Shaft Assy.

1

1

1

1

1

1

(Optional)

COMMERCIAL DISPOSER

MODEL NO. SS100-40

1 YR (208/230/380 Volt / 50 Hz / 3 Phase)
FULLWRNTY 1 H P

Start Date:

11/06/95

Engineer Number

13660-N

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

NO.

2 11016 1 Gasket, Mounting
3 11020-A 1 Upper Body Assy 27 12370 1 Trim Band
4 1491 6 Screw (1/4-20x3/4) 28 1836-A 2 Screw (8-32x1/2)
5 11227 1 Plug, Pipe 29 13714-B 1 Stator Assy
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy 30 12433-P 1 Bracket Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut 31 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 32 12378 1 Clamp, Overload
11 12142 1 Washer, Fiber 33 8221 2 Screw (8-32x1/2)
12 13586 1 Rotor Shredder Assy 34 13396-E 1 Box, Terminal Assy
13 13928 1 Upper End Bell Assy

14 12936 1 Shield 36 13559 1 Grommet, Overload
15 13919 6 Screw (8-18x1/2) 37 13422-BB
16 12934-A
17 12935
18 12860
19 12319
20 12322
21 12326
22 11322 3 Key. Woodruff 44 13677 1 Ring, Retaining
23 13080-A 1 Kit, Bearing Seal 45 12490 3 Tube, Spacer

24 11444 3 Washer, Lock 47 11940-A 3 Bolt, Thru
25 3135 3 Screw (1/4-20x1) 48 11757-B 2 Tube, Foot Assy.

PART

NO.

NO.

REQ.

(lncl.Codes14-22) 35 12381 1 Screw (8-32x1-1/4)

Seal Assy 38 12384 1 Bushing
Sleeve, Spacer 39 2466-A 1 Screw, Ground
0-Ring 40 13709 1 Bearing, Lower
Slinger 41 13678 1 Spring, Pre-load
Upper Bearing Assy 42 13747 1 End Frame, Lower
Seal, Water & Oil 43 13676 1 Fan

(lncl. codes 9-11&14-22) 46 12396 1 Cover, Bottom

DESCRIPTION

CODE

NO.

PART

NO.

NO.

REQ.

(Incl. Codes 40)

(Mounting)

(Incl. code 36)

1 Overload Protector

DESCRIPTION

ENVIROVAC

1 11004

1

Flange, Mounting

27

12370

1

Trim Band

1

29

1

1

32

1

7

1

33

2

8

1

34

1

1

35

1

1

38

1

1

40

1

15

6

41

1

16

1

42

1

1

45

3

1

47

3

22

3

48

2

23

1

3

1

COMMERCIAL DISPOSER

MODEL NO. SS100-41

1 YR (460 Volt/ 60 Hz/ 3 Phase)

FULLWRNTY 1 H.P.

Start Date:

01/96

EngineerNumber

13660-P

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

PART NO.

NO.

2 11016 1 Gasket, Mounting 28 1836-A 2 Screw (8-32x1/2)
3

11020-A

4 1491 6 Screw (1/4-20x3/4) 30 12433-P 1 Bracket Assy (Mounting)
5 11227 1 Plug, Pipe 31 11448 4 Screw (8-18x1/4)
6

9 11260 1 Nut

10

11 12142 1 Washer, Fiber 36 13559 1 Grommet. Overload

12 13799 1 Rotor Shredder Assy 37 13422-BE : 1 Overload Protector

13

11006
12442
13798

12445

13928

14

17 12935 1 Sleeve, Spacer 43 13676 1 Fan

18 12860 1 0-Ring 44 13677 1 Ring, Retaining

19

20 12322 1 Upper Bearing Assy. 46 12396 1 Cover, Bottom

21

12936
13919

12934-A

12319

12326
11322
13080

24

25 3135 3 Screw (1/4-20x1)

26

11444

13592-E

NO.

REQ.

DESCRIPTION

Upper Body Assy

Gasket, Shredder
Body & Cover Assy
Shredder, Stationary

Washer

Upper End Bell Assy
(Incl. Codes 14-22) 39 2466-A 1 Screw, Ground
Shield
Screw (8-18x1/2)
Seal Assy

Slinger

Seal, Water & Oil
Key, Woodruff
Kit, Bearing Seal
(Incl. 9-11 & 14-22)
Washer, Lock

CODE

NO.

PART

NO.

13714-B

12378

8221

13396-E

NO.

REQ.

12381

12384

13709
13678
13747

12490

11940-A
11757-B

DESCRIPTION

Stator Assy

Clamp. Overload
Screw (8-32x1/2)
Box. Terminal Assy
(Incl. code 36)
Screw (8-32x1-1/4)

Bushing

Bearing, Lower
Spring, Pre-load
End Frame, Lower

Tube.Spacer

Bolt, Thru
Tube,Foot Assy
(Optional)

Rotor & Shaft Assy.
(Incl. Codes 40)

ENVIROVAC

13422

-

COMMERCIAL DISPOSER

MODEL NO. SS100-42

1 YR (380Volt/50Hz/3Phase)
Full WRNTY

Start Date:

01/96

Engineer Number

13660-S

1H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

NO.

PART NO.

1 11004 1 Flange, Mounting 26 13592-E

2 11016 1 Gasket, Mounting

3 11020-A 1 Body, Assy, Upper 27 12370 1 Trim Band

4 1491 6 Screw (1/4-20x3/4) 28 1836-A 2 Screw (8-32x1/2)

5 11227 1 Plug, Pipe 29 13714-B

6 11006 1 Gasket. Shredder 30 12433-P

7 12442 1 Body & Cover Assy.

8 13798 1 Shredder, Stationary 31 11448 4 Screw (8-18x1/4)

9 11260 1 Nut 32 12378 1 Clamp, Overload

10 12445 1 Washer 33 8221 2 Screw (8-32x1/2)
11 12142 1 Washer. Fiber 34 13396-E
12 13799 1 Assy, Rotor Shredder
13 13928 1 Assy, Upper End Bell 35 12381 1 Screw (8-32x1-1/4)

14 12936 1 Shield 37
15 13919 6 Screw (8-18x1/2) 38 12384
16 12934-A 1 Seal Assy 39 2466-A
17 12935 1 Sleeve, Spacer 40 13709
18 12860 1 0-Ring 41 13678
19 12319 1 Slinger 42 13747 1 End Frame, Lower
20 12322 1 Assy, Upper Bearing 43 13676 1 Fan
21 12326 1 Seal, Water & Oil 44 13677 1 Ring, Retaining
22 11322 3 Key, Woodruff 45 12490 3 Tube. Spacer
23 13080^A 1 Kit, Bearing Seal (Incl. 46 12396 1 Cover, Bottom

24 11444 3 Washer. Lock 48 11757-B
25 3135 3 Screw (1/4-20x1)

NO.

REQ.

(lncl.Codes14.22) 36 13559

Codes 9-11& 14-22) 47 11940-A

DESCRIPTION

CODE

NO.

PART

NO.

NO.

REQ.

1 Rotor & Shaft Assy.

(Incl. Codes 40)

1 Stator Assy
1 Bracket Assy

(Mounting)

1 Box. Terminal Assy

(Incl. code 36)
Grommet, Overload

1

Overload Protector

1

Bushing

1

Screw, Ground

1

Bearing, Lower

1

Spring, Pre-load

1

3 Bolt, Thru
2 Tube, Foot Assy.

(Optional)

DESCRIPTION

ENVIROVAC

13660T

1 11004

1

Flange, Mounting

27

14131

1

Centrifugal Actuator

(Includes Codes

27 & 44)

COMMERCIAL DISPOSER

MODEL No. SS100-43

1-YR (115/208/230 Volt / 50Hz / 1 Phase)

FULL WRNTY 1 H.P.

Start Data:

1/99

Engineer
Number:

Rev:

ORDER BY PASTNUMBER, NOT CODE NUMBER

CODE

NO.

10 13987 1 Washer 36 12378 1 Clamp, Overload

11 12142

12 13586 1 Rotor Shredder Assy 38 13396-E 1 Box, Terminal Assy

13 13597-C 1 Upper End Bell Assy (Includes Code 40)

14 12936 1 Shield 40 13559 1 Plug, Button

15 13919 6 Screw (#10-24 x 3/8PH) 41 13422-BB 1 Overload Protector

16 12934-A 1 Seal Assy 42 12384 1 Bushing

17 12935 1 Sleeve, Spacer 43 2466-A 1 Screw, Ground

18 12860 1 0-Ring 44 13709 1 Bearing, Lower

19 12319 1 Slinger 45 13678 1 Spring, Pre-load

20 12610 1 Upper Bearing Assy 46 13710 1 End Frame, Lower

21 12326 1 Water & Oil Seal 47 13676 1 Fan

22 11322 3 Key, Woodruff 48 13677 1 Ring, Retaining

23 13080-A 1 Kit, Bearing Seal 49 12490 3 Tube, Spacer

24 11444 3 Washer, Lock 51 11940-A 3 Bolt, Thru

25 3135 3 Screw (1/4-20x1) 52 11757-B 2 Tube, Foot Assembly

26 13592-C 1 Rotor & Shaft Assembly

PART NO.

2 11016 1 Gasket, Mounting 28 8221 2 Screw (8-32 x 1/2)
3 11020-A 1 Body Upper Assy 29 13707 1 Switch, Start
4 1491 6 Screw (1/4-20 x 3/4) 30 12370 1 Trim Band
5 11227 1 Plug, Pipe 31 1836-A 2 Screw (8-32 x 1/2)
6 11006 1 Gasket, Shredder 32 13656-B 1 Stator Assy
7 12442 1 Body & Cover Assy 33 12433 1 Bracket Assy (Mounting)
8 11252-A 1 Shredder, Stationary 34 11448 4 Screw (8-18x1/4)
9 13952

(Includes Codes 14-22) 39 12381 1 Screw (8-32x1-1/4)

(Includes Codes 9-11 & 14-22) 50 12396 1 Cover, Bottom

NO.

REQ.

1

1

DESCRIPTION

Nut 35 11868 1 Capacitor

Washer, Fiber 37 8221 2 Screw (8-32 x 1/2)

CODE

NO.

PART NO.

NO.

REQ.

DESCRIPTION

(Optional)

Start Date:

IN

SINK

COMMERCIAL DISPOSER

1 11004

1

Flange, Mounting

31

14131

1

Centrifugal Actuator

1

1

1

1

1

ERATOR

MODEL NO. SS100-44

(100/200 Volt / 50/60HZ /1 Phase)

1 H.P.

3/99

Engineer Number:

13660-U

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting 32 8221 2 Screw (8-32x1/2)
3 11020-A 1 Body, Assy. Upper 33 13707 1 Switch, Start
4 1491 6 Screw (1/4-20x3/4) 34 12370 1 Trim Band
5 11227 1 Plug, Pipe 35 1836-A 2 Screw (8-32x1/2)
6 11006 1 Gasket, Shredder 36 13713-B 1 Stator Assy.
7 12442 1 Assy. Body & Cover 37 12433 1 Bracket Assy.
8 11252-A 1 Shredder, Stationary 38 11448 4 Screw (8-18x1/4)

9 11260
10 12445
11 12142
12 12944
13 13722

14 12936 1 Shield 44 12383 1 Grommet, Overload
15 1269 6 Screw (8-18x1/2) 45 13422-T 1 Overload Protector
16 12934-A 1 Assy. Seal 46 12384 1 Bushing
17 12935 1 Sleeve, Spacer 47 2466-A 1 Screw, Ground
18 12860 1 0-Ring 48 13709 1 Bearing, Lower
19 12319 1 Slinger 49 13678 1 Spring, Pre-load
20 12610 1 Assy. Upper Bearing 50 13710 1 End Frame, Lower
21 12326 1 Seal, Water & Oil 51 13676 1 Fan
22 11322 3 Key, Woodruff 52 13677 1 Ring, Retaining
23 13080 1 Kit, Bearing Seal (Incl. 53 11940-A 3 Bolt, Thru

24 11444 3 Washer, Lock 55 12396 1 Cover, Bottom
25 3135 3 Screw (1/4-20x1) 56 11757-B 2 Tube, Foot Assy.
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-B 1 Rotor & Shaft Assy.

(Incl. Codes 31 & 48)

Nut 39 11868 1 Capacitor
Washer 40 12378 1 Clamp, Overload
Washer, Fiber 41 8221 2 Screw (8-32x1/2)
Assy. Rotor Shredder 42 13396G 1 Box, Terminal Ass.
Assy. Upper End Bell
(Incl. Codes 14 - 22) 43 12381 1 Screw (8-32x1-1/4)

Codes 9-11 & 14-22) 54 12490 3 Tube, Spacer

(Incl. code 44)

(Optional)