Insignia NS-TVMFP12 User Manual

INSTALLATION GUIDE

FIXED-POSITION WALL MOUNT FOR TVs 19-39 in.

NS-TVMFP12

Safety information and specifications . . .2

For either wood-stud or concrete wall installations

Before using your new product, please read these instructions to prevent any damage.

Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . .3

Package contents . . . . . . . . . . . . . . . . . . . . . .3

Installation instructions. . . . . . . . . . . . . . . . .5

FIXED-POSITION WALL MOUNT FOR TVs 19-39 in.

Safety information and specifications

Maximum TV weight: 50 lbs. (22.7 kg) Screen size: 19 in. to 39 in. diagonal Overall dimensions (H × W ):

12.6 × 15.5 in. (32 × 39.4 cm)

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

CAUTION: Do not use this

product for any purpose not explicitly specified by Insignia.

Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service or call a qualified contractor. Insignia is not responsible for damage or injury caused by incorrect installation or use.

The weight of your TV must not exceed 50 lbs. (22.7 kg). The wall must be c apable of sup porting five times the weight of your TV and wall mount combined.

This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!

Wall-mount weight: 3 lbs. We’re here for you

www.insigniaproducts.com For customer service, call: 877-467-4289 (U.S./Canada markets)

15.5 in. (39.4 cm)

12.6 in. (32 cm)

www.insigniaproducts.com

FIXED-POSITION WALL MOUNT FOR TVs 19-39 in.

Tools needed

ardware

Edge-to-edge stud finder

Phillips screwdriver

Measuring tape

You will need the following tools to assemble your new TV wall mount:

Level

Socket wrench with 1/2 in. (13 mm) socket or adjustable wrench

Tap e

Drill

7/32 in. (5.5 mm) wood drill bit (for wood stud wall)

3/8 in. (10 mm) masonry drill bit (for concrete wall)

Hammer

Package contents

Make sure that you have all the hardware necessary to assemble your new TV wall mount:

A Wall Plate (1) C Right TV Bracket (1) B Left TV Bracket (1) P Wall plate template (1)

www.insigniaproducts.com

TV Hardware Bag

FIXED-POSITION WALL MOUNT FOR TVs 19-39 in.

Label Hardware Qty.

M4 × 12 mm screw

M4 × 35 mm screw

M4/M5 washer

Label Hardware Qty.

M8 × 16 mm screw

M6/M8 washer

Spacers

M5 × 12 mm screw

M5 × 35 m screw

M6 × 12 mm screw

M6 × 20 mm screw

M8 × 35 mm screw

Lag bolt washer

5/16 in. × 2 3/4 in. lag bolt

M6 × 35 mm screw

M8 × 20mm screw

1234in

10 20 30 40 50 60 70 80 90 100 mm

www.insigniaproducts.com

FIXED-POSITION WALL MOUNT FOR TVs 19-39 in.

Installation instructions

STEP 1 - Determine whether your TV has a flat back or an irregular or obstructed back

Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches.

If your TV has a ta ble-top stand attached, remove the stand. See the documentation that c ame with your TV for instructions.

Temporarily lay the TV brackets (B and C) on the back of your TV.

Align the screw holes in the TV brackets with the mounting screw holes on your TV.

Identify which type of back your TV may have:

• Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need spacers when assembling the wall mount.

• Obstructed back: The brackets block one or more of the jacks on the back of your TV. You will need spacers when assembling the wall mount.

• Irregularly-shaped back: There is a gap between a bracket and some part of the back of your TV. You will need spacers when assembling the wall mount.

Remove the TV brackets.

www.insigniaproducts.com

FIXED-POSITION WALL MOUNT FOR TVs 19-39 in.

STEP 2 - Select screws, washers, and spacers

Select the hardware for your T V (screws, washers, and spacers). A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back of the TV.) If you don't know the correct length of the mounting screws your TV requires, test various sizes by hand threading the screws. Select one of the following types of screws:

For a TV with a flat back:

M4 X 12mm screws (D) M5 X 12mm screws (I) M6 X 12mm screws (K) M6 X 20mm screws (L) M8 X 16mm screws (N) M8 X 20mm screws (O)

For a TV with an irregular/obstructed back:

M4 X 35mm screws (E) M5 X 35mm screws (J) M6 X 35mm screws (M) M8 X 35mm screws (Q)

Select either an M4/M5 washer (F) or an M6/M8 washer (G) For an irregular or obstructed TV back, also use Spacer (H)

CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer service. Use the shortest screw and spacer combination to accommodate your T V. Using hardware that is too long may damage your T V. However, using a screw that is too short may cause your TV to fall from the mount.

Screw fits correctly

Remove the screws.

For a flat back TV, go to “STEP 3 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on

Screw is too short

Screw is too long

page 7.

-ORFor an irregular or obstructed back, go to “STEP 3 - Option 2: Attaching the mounting hardware to TVs

with irregular or obstructed backs” on page 8.

www.insigniaproducts.com

+ 14 hidden pages