Manufacturers, retailers and the rest of the consumer electronics industry are
committed to making home entertainment safe and enjoyable.
•
As you enjoy your television, please note that all televisions - new and old - must be
supported on proper stands or installed according to the manufacturer's
recommendations. Televisions that are inappropriately situated on dressers, bookcases,
shelves, desks, speakers, chests, carts, etc., may fall over, resulting in injury.
TUNE IN TO SAFETY
•
ALWAYS follow the manufacturer’s recommendations for the safe installation of your
television.
•
ALWAYS read and follow all instructions for proper use of your television.
•
NEVER allow children to climb on or play on the television or the furniture on which the
television is placed.
•
NEVER place the television on furniture that can easily be used as steps, such as a chest
of drawers.
•
ALWAYS install the television where it cannot be pushed, pulled over or knocked down.
•
ALWAYS route cords and cables connected to the television so that they cannot be
tripped over, pulled or grabbed.
WALL OR CEILING MOUNT YOUR TELEVISION
•
ALWAYS contact your retailer about professional installation if you have any doubts
about your ability to safely mount your television.
•
ALWAYS use a mount that has been recommended by the television manufacturer and
has a safety certification by an independent laboratory (such as UL, CSA, ETL).
•
ALWAYS follow all instructions supplied by the television and mount manufacturers.
•
ALWAYS make sure that the wall or ceiling where you are mounting the television is
appropriate. Some mounts are not designed to be mounted to walls and ceilings with
steel studs or cinder block construction. If you are unsure, contact a professional
installer.
•
Televisions can be heavy. A minimum of two people is required for a wall or ceiling
mount installation.
MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR
HOME
•
Many new television buyers move their older CRT televisions into a secondary room
after the purchase of a flat-panel television. Special care should be made in the
placement of older CRT televisions.
•
ALWAYS place your older CRT television on furniture that is sturdy and appropriate for
its size and weight.
•
NEVER place your older CRT television on a dresser where children may be tempted to
use the drawers to climb.
•
ALWAYS make sure your older CRT television does not hang over the edge of your
furniture.
https://www.cta.tech/Consumer-Resources.aspx
5
NS-22D420NA18
Important Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates that
dangerous voltage
constituting a risk of electric
shock is present within your TV.
This label is located on the
back of your TV.
This symbol indicates that
there are important operating
and maintenance instructions
in the literature accompanying
your TV.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the
cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15 The wall plug is the disconnecting device. The plug
must remain readily operable.
16 Remote control batteries should not be exposed
to excessive heat such as sunshine, fire, or the like.
17 The apparatus should not be exposed to dripping
or splashing, and no objects filled with liquids,
such as vases, should be placed on the apparatus.
18 Your TV has four VESA mounting holes on the
back. If you attach a wall-mount bracket or TV
stand to the back of your TV, the bracket or stand must be securely attached using all four holes.
If you do not use all four mounting holes, your TV
may fall and cause property damage or personal
injury. See the documentation that came with
your wall mount or TV stand for complete
mounting instructions.
WARNING
Electric shock hazard
To reduce the risk of fire or electric shock, do not
remove any cover or expose the device to rain or
moisture. No user-serviceable parts are inside. Refer
servicing to qualified service technicians.
Lightning
For added protection for your device receiver during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
power outlet and disconnect any antenna or cable
system. This helps prevent property damage and
personal injury from lightning and power line surges.
Power lines
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, take extreme care to keep from
touching such power lines or circuits as contact with
them might be fatal.
Handling the LCD panel
• Your TV’s screen is made of glass. Do not drop your
TV or hit, jolt, or press hard against the LCD panel. If
the screen breaks, be careful of broken glass.
• If the LCD panel is broken, make absolutely sure that
you do not touch the liquid in the panel. This may
cause skin inflammation.
• If the liquid gets in your mouth, immediately gargle,
rinse, and consult with your doctor. Also, if the liquid
gets in your eyes or touches your skin, consult with
your doctor after rinsing for at least 15 minutes or
longer in clean water.
6
www.insigniaproducts.com
Replacement parts
When replacement parts are required, make sure that
the service technician uses replacement parts
specified by the manufacturer that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock,
personal injury, or other hazards.
Safety check
After completing any service or repair to this device,
ask the service technician to perform routine safety
checks to determine that your TV is in correct
operating condition.
Power source
Operate your TV only from the type of power source
indicated on the marking label. If you are not sure of
the type of power supplied to your home, consult an
electrician or your local power company.
Servicing
These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that
contained in the operating instructions unless you are
qualified to do so.
CAUTION
Damage requiring service
Unplug this TV from the power outlet and refer
servicing to qualified service personnel under the
following conditions:
• When the power supply cord or plug is damaged or
frayed.
• If liquid has been spilled or objects have fallen into
your TV.
• If your TV has been exposed to rain or water.
• If your TV does not operate normally by following
the operating instructions. Adjust only those
controls covered by the operating instructions
because incorrect adjustment of other controls may
result in damage and will often require extensive
work by a qualified technician to restore your TV to
its normal operation.
• If your TV has been dropped or damaged in any
way.
• When your TV exhibits a distinct change in
performance.
Outdoor antenna grounding
If an outside antenna or cable system is connected to
your T V, make sure that the antenna or cable system is
grounded to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides
information with respect to correct grounding of the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of the
antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding
electrode.
Antenna lead-in wire
1
Grounding clamp
2
Antenna discharge
3
unit
Grounding conductors
4
Ground clamps
5
Power service
grounding electrode
6
system
Electric service
7
equipment
Note to CATV system installer
Article 820 of the National Electrical Code, ANSI/NFPA
No. 40 provides guidance for correct grounding.
Specifically, it states that the cable ground must be
connected to the grounding system of the building as
close to the point of cable entry as practical.
Condensation
Moisture will form on the TV if the TV is brought from
cool surroundings into a warm room or if the
temperature of the room rises suddenly. When this
happens, the TV's performance may be impaired. To
prevent this, let the TV stand in its new surroundings
for about an hour before switching it on, or make sure
that the room temperature rises gradually.
Condensation may also form during the summer if
the TV is exposed to the breeze from an air
conditioner. In such cases, change the location of the
TV.
Mobile telephone warning
To avoid interference with your TV picture and sound,
operating problems, or even damage, keep your
cordless and cellular telephones away from the TV.
End of life directives
Your TV may contain materials that are regulated for
environmental reasons. Your TV also contains
materials that can be recycled and reused. To help
protect the environment, contact your local
authorities for information about disposal or recycling
and about finding a recycler in your area before you
dispose of your TV.
Non-active pixels
The LCD panel contains almost 3 million thin film
transistors, which provide exceptionally sharp video
quality. Occasionally, a few non-active pixels may
appear on the screen as a fixed blue, green, or red
point. These non-active pixels do not adversely affect
the performance of your TV, and are not considered
defects.
www.insigniaproducts.com
7
NS-22D420NA18
22" 1080p 60Hz LED TV
Introduction
Congratulations on your purchase of a high-quality
Insignia product. Your NS-22D420NA18 represents
the state of the art in LED TV design and is designed
for reliable and trouble-free performance.
INlink
Enjoy the benefit of having HDMI CEC-compatible
products plug and play! No setup is needed! CEC
technology lets different devices discover and
communicate with each other. (See page 38 for
instructions on how to use INlink.)
DTS Sound™
DTS Sound delivers clear, crisp, and natural sound
while providing deep enveloping bass.
Game mode
Video games generally require adjustments to the TV
picture settings to get the maximum experience. By
simply pressing the GAME button on your remote
control, your TV settings will automatically adjust for
video games. It couldn't be easier.
Audio accessibility
Your TV provides audio descriptions of menus and
some remote control functions. Depending on the
broadcaster, audio narration of key elements in
programs may also be available. (See page 62 for
instructions on how to turn on audio narration.)
8
www.insigniaproducts.com
Installing the stands or wall-mount bracket
Notes
• If you plan to wall-mount your TV, do not install the stands.
• Store the stands and stand screws in case you decide to use the stands
in the future.
Installing the stands
1 Carefully place your TV face-down on a cushioned, clean surface to protect the screen from damages and scratches.
22" 1080p 60Hz LED TV
2 Align the screw holes on the TV stands with the holes on the bottom of your TV, then secure each stand to your TV
with two of the provided screws.
Screw typeScrew length# of screws
ST414 mm4
www.insigniaproducts.com
9
NS-22D420NA18
Installing a wall-mount bracket
Warnin g
• Your TV has four VESA mounting holes on the back. If you attach a
wall-mount bracket to the back of your TV, the bracket must be
securely attached, using all four holes. If you do not use all four
mounting holes, your TV may fall and cause property damage or
personal injury. See the documentation that came with your wall mount
for complete mounting instructions.
• This TV is intended to be supported by a UL Listed wall mount bracket
with suitable weight/load. (See Miscellaneous on page 73.)
1 Carefully place your TV face-down on a cushioned, clean surface to protect the screen.
2 If the TV stands are installed, remove the screws that secure the stands to your TV.
10
www.insigniaproducts.com
22" 1080p 60Hz LED TV
3 Attach the wall-mount bracket to your TV using the mounting holes on the back of your TV. See the instructions that
came with the wall-mount bracket for information about which screws to use and how to correctly hang your TV.
Notes
• The length of the wall-mount screws vary depending on the wall-mount
bracket you purchased. We recommend that you use the wall-mount
screws and spacers that came with your TV. They fit most wall-mount
brackets.
• Make sure that the screws you use are the correct length. The threaded
parts of the screws that are inserted into the back of your TV must be at
least 9.5mm in length and not more than 11.5mm in length. If the screws
are too short, your TV may fall off the wall-mount bracket. If the screws
are too long, they may damage components inside your TV. For more
information, see the instructions that came with the wall-mount bracket.
• The mounting holes on the back of your TV take type M4 screws.
3.94 in. (100 mm)
3.94 in. (100 mm)
www.insigniaproducts.com
11
NS-22D420NA18
TV components
Your TV has several sets of jacks for connecting
devices to your TV.
This section contains information about:
•Package contents
•Front
•Jacks
• Remote control
Package contents
•22" LED TV
• Remote control and batteries (2 AAA)
•TV stands (2)
• TV stand screws: ST4 (4 pcs.)
•Wall mount screws: M4 (4 pcs.)
• Quick Setup Guide
• Important Information
Front
#ItemDescription
Remote control
1
sensor
2
Power indicator
Receives signals from the remote
control. Do not block.
Turns off when your TV is on.
Lights red when your TV is off
(standby mode).
12
www.insigniaproducts.com
22" 1080p 60Hz LED TV
Jacks
#ItemDescription
—Press to turn on your TV when
your TV is off (in standby mode).
Press and hold to turn off your TV
when TV is on.
Warnin g: When your TV is off,
power still flows through it. To
completely disconnect power,
1/INPUT button
DIGITAL OUTPUT
2
(COAXIAL)
unplug the power cord.
INPUT—Quickly press and release
to open the INPUT SOURCE list, press
one or more times to select a video
input source, then wait a few
seconds. Your TV switches to the
source you selected. For more
information, see Selecting the video
input source on page 36.
Connect a sound bar, digital
speaker system, or home theater
system to this jack to listen to TV
audio through external speakers.
For more information, see Digital
audio on page 27.
#ItemDescription
Connect headphones, a sound bar,
analog speaker system, or a home
3/AUDIO OUT
4
ANT/CABLE IN
VIDEO and
5
L and R AUDIO
USB
6
7 HDMI 1 (ARC)
8
HDMI 2
theater system to this jack to listen
to TV audio through external
speakers. For more information, see
Analog audio on page 28.
Connect an antenna or cable TV to
this jack. For more information, see
Coaxial (good) on page 18 or
Connecting an antenna or cable TV
(no box) on page 19.
Connect the video and audio for an
AV device to these jacks. For m ore
information, see AV (good) on
page 17, 21, or 23.
Connect a USB flash drive to this
jack to view compatible JPEG
picture files. For more information,
see Connecting a USB flash drive on
page 25 and Using a USB flash drive
on page 42.
Connect an HDMI device to this
jack. For more information, see
HDMI (best) on page 16, 20, or 22, or
Connecting a computer on page 24.
OR
Connect an ARC-enabled home
theater receiver to this jack.
Connect an HDMI device to this
jack. For more information, see
HDMI (best) on page 16, 20, or 22, or
Connecting a computer on page 24.
www.insigniaproducts.com
13
NS-22D420NA18
Remote control
#ButtonPress to...
SLEEP
10
Media controls
11
INPUT
12
(return)Return to the previous channel.
13
FAVO RI TE
14
S T W X
15
INFO*
16
CC
17
MUTEMute or un-mute the sound.
18
CH/CH
19
Set the sleep timer. You can select Off, 5, 10, 15, 30, 60, 90,
120, 180, or 240 minutes. See Setting the sleep timer on
page 60.
Control INlink-compatible (HDMI CEC) devices. See Us ing
INlink on page 38.
Open the INPUT SOURCE list. Press S or T to select the
video input source, then press ENTER. See Selecting the
video input source on page 36.
Set up the Favorite channel list or open the existing Favorite
channel list. Se e Setting up a favorite channel list on page 50
and Viewing a favorite channel on page 51.
TV menus—Navigate in on-screen TV menus and to adjust
settings.
USB—Control a photo slideshow.
Display TV status information, such as the channel number,
channel name (if available), or signal source. See Vie win g
channel information on page37 .
Turn closed captioning on or off. You can select CC Off, CC On, or CC On when mute. Se e Turning closed captioning on
or off on page 57.
TV: Change to the next higher or lower channel in the
channel list.
TV menu: Navigate up or down.
#ButtonPress to...
Turn your TV on or off (standby mode).
(power)
1
NumbersEnter channel numbers and the parental control password.
2
3
MENUOpen the on-screen menu.
4
ENTERConfirm selections or changes in TV menus.
5
EXITClose the on-screen TV menu.
6
ACC
7
VOL+/VOL–
8
ASPECT
9
Warn ing: When your TV is off, power still flows through it.
To disconnect power, unplug the power cord.
Enter a digital sub-ch annel number. See Selecting a channel
on page 37.
Open the Accessib ility menu. See Adjusting accessibility
settings on page 62.
TV: Adjusts the volume.
TV menu: Navigate left or right.
USB: Control a photo slideshow.
TV: Change how the pictures appears on the screen.
USB: Zoom when displaying a photo.
GAMEChange the picture mode to Game mode.
20
Select the picture mode. You can select Vivid, Standard,
21
22
PICTURE
AUDIO
Energy Sav ings, Movie, Game, or Custom. See the
Picture Mode option in Adjustin g the TV pic ture on
page 44.
Select the audio mode. You can select Standard, Theater, Music, News, or Custom. See the AUDIO Mo de option in
Adjusting sound settings on page 46.
14
www.insigniaproducts.com
22" 1080p 60Hz LED TV
What connection should I
use?
Your TV has several connection types for connecting
devices to your TV.
For the best video quality, you should connect a
device to the best available connection.
Use the following tables to identify cables:
Video
quality
Best (use this
if your devices
have HDMI)
Good
Connection
type and
jack
HDMI
video/audio
AV (requires an
audio
connection)
Cable connector
Connection
type and
jacks
Coaxial digital
audio
Analog audio
input
3.5mm analog
audio output
Cable connectors
Good
Coaxial
video/audio
Cautions
• Check the jacks for position and type
before making any connections.
• Loose connections can cause poor audio
or video quality. Make sure that all
connections are tight and secure.
• The external audio/video equipment
shown may be different from your
equipment. If you have questions, refer to
the documentation that came with your
equipment.
• Always unplug the power cord when
connecting external equipment.
www.insigniaproducts.com
15
NS-22D420NA18
Connecting a cable or satellite box
Many cable or satellite TV boxes have more than one connection type. To get the best video, you should use the best
connection type available. For more information, see What connection should I use? on page 15.
You can connect a cable or satellite box using:
•HDMI (best)
•AV (good)
• Coaxial (good)
HDMI (best)
Cable or
Side of TV
On your TV
HDMI cable
connector
satellite box
HDMI jack
HDMI cable
Cable wall
jack
1 Make sure that your TV’s power cord is unplugged and all connected equipment is turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect an HDMI cable (not provided) to one of the HDMI jacks on the side of your TV and to the HDMI OUT jack on
the cable or satellite box.
4 Plug your TV’s power cord into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 Press INPUT to open the INPUT SOURCE list.
6 Press
S
or T to highlight HDMI1 or HDMI2, then press ENTER.
Note
An HDMI cable carries both audio and video. You do not need to use any
audio cables.
16
www.insigniaproducts.com
AV (good)
22" 1080p 60Hz LED TV
Notes
Cables are often color-coded to match color-coded jacks.
AV
connector
AV jack
On your TV
Audio cable
connectors
Analog audio
Cable w all
jack
jacks
Back of TV
AV cab le
Cable or
satellite box
1 Make sure that your TV’s power cord is unplugged and all connected equipment is turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect an AV cable (not provided) to the VIDEO jack and L and R AUDIO jacks on the back of your TV and to the AV
and audio out jacks on the cable or satellite box.
Important
When you connect the audio using the L and R AUDIO jacks, the audio
output is analog.
4 Plug your TV’s power cord into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 Press INPUT to open the INPUT SOURCE list.
6 Press
S
or T to highlight AV, then press ENTER.
www.insigniaproducts.com
17
NS-22D420NA18
Coaxial (good)
Cable or satellite
box
On your TV
Coaxial cable
connector
ANT/CABLE IN
jack
Back of TV
1 Make sure that your TV’s power cord is unplugged and all connected equipment is turned off.
2 Connect the incoming cable from the cable wall jack to the cable-in jack on the cable or satellite box.
3 Connect a coaxial cable (not provided) to the ANT/CABLE IN jack on the back of your TV and to the coaxial out jack
on the cable or satellite box.
4 Plug your TV’s power cord into a power outlet, turn on your TV, then turn on the cable or satellite box.
5 Press INPUT to open the INPUT SOURCE list.
6 Press
7 If you cannot tune to channels you know exist, scan for channels. See Automatically scanning for channels on
S
page 48.
or T to highlight TV, then press ENTER.
Coaxial cable
Cable
wall jack
18
Notes
• Use a coaxial cable to eliminate interference and noise from radio
waves.
• Do not bundle the coaxial cable with the power cord or other cables.
www.insigniaproducts.com
Connecting an antenna or cable TV (no box)
Antenna or cable TV
(no box)
On your TV
22" 1080p 60Hz LED TV
Coaxial cable
connector
ANT/CABLE IN
jack
Back of TV
1 Make sure that your TV’s power cord is unplugged and all connected equipment is turned off.
2 Connect a coaxial cable (not provided) to the ANT/CABLE IN jack on the back of your TV and to the antenna or cable
TV wall jack.
3 Plug your TV’s power cord into a power outlet, then turn on your TV.
4 Press INPUT to open the INPUT SOURCE list.
5 Press
6 If you cannot tune to channels you know exist, scan for channels. See Automatically scanning for channels on
S
page 48.
Notes
or T to highlight TV, then press ENTER.
• Use a coaxial cable to eliminate interference and noise from radio waves.
• Do not bundle the coaxial cable with the power cord or other cables.
• If the antenna is not installed correctly, contact qualified service personnel to correct the
problem.
• If the signal level for a channel is weak, the picture may be distorted. Adjust the antenna
or use a highly directional outdoor or set-top antenna with a built-in amplifier.
• If the picture quality is good on some channels and poor on others, the problem may be
caused by a poor or weak signal from the broadcaster or cable TV provider.
• If you connect to cable TV without a set-top box and experience poor picture quality, you
may need to install a set-top box to improve signal reception and picture quality. Contact
your cable TV provider about upgrading to a set-top box.
• Many high-definition (HD) channels upscale standard-definition (SD) content. The picture
displayed on your TV is still displayed as SD, thus the picture quality will not be as clear or
crisp as it would be if the content was originally recorded in HD.
Coaxial cable
www.insigniaproducts.com
19
NS-22D420NA18
Connecting a DVD or Blu-ray player
Many DVD or Blu-ray players have more than one connection type. To get the best video, you should use the best
connection type available. For more information, see What connection should I use? on page 15.
You can connect a DVD or Blu-ray player using:
•HDMI (best)
•AV (good)
HDMI (best)
DVD or Blu-ray
Side of TV
On your TV
HDMI cable
connector
player
HDMI jack
HDMI cable
1 Make sure that your TV’s power cord is unplugged and the DVD or Blu-ray player is turned off.
2 Connect an HDMI cable (not provided) to one of the HDMI jacks on the side of your T V and to the HDMI OUT jack on
the DVD or Blu-ray player.
3 Plug your TV’s power cord into a power outlet, then turn on your TV and DVD or Blu-ray player.
4 Press INPUT to open the INPUT SOURCE list.
5 Press
S
or T to highlight HDMI1 or HDMI2, then press ENTER.
Note
An HDMI cable carries both audio and video. You do not need to use any
audio cables.
20
www.insigniaproducts.com
AV (good)
22" 1080p 60Hz LED TV
Notes
Cables are often color-coded to match color-coded jacks.
On your TV
AV cab le
connector
AV jack
1 Make sure that your TV’s power cord is unplugged and the DVD or Blu-ray player is turned off.
2 Connect an AV cable (not provided) to the VIDEO jack and L and R AUDI O jacks on the back of your TV and to the
AV OUT jacks on the DVD or Blu-ray player.
3 Plug your TV’s power cord into a power outlet, then turn on your TV.
4 Turn on the DVD or Blu-ray player, then set it to the correct output mode. For more information, see the
documentation that came with the player.
5 Press INPUT to open the INPUT SOURCE list.
6 Press
S
Audio cable
connectors
Analog
audio jacks
Back of TV
Important
When you connect the audio using the L and R AUDIO jacks, the audio
output is analog.
or T to highlight AV, then press ENTER.
DVD or Blu-ray
player
AV c a ble
www.insigniaproducts.com
21
NS-22D420NA18
Connecting a game console
You can connect a game console using:
•HDMI (best)
•AV (good)
HDMI (best)
Side of TV
On your TV
HDMI cable
connector
HDMI jack
1 Make sure that your TV’s power cord is unplugged and the game console is turned off.
2 Connect an HDMI cable (not provided) to one of the HDMI jacks on the side of your T V and to the HDMI OUT jack on
the game console.
3 Plug your TV’s power cord into a power outlet, then turn on your TV.
4 Turn on the game console, then set it to the correct output mode. For more information, see the documentation that
came with the console.
5 Press INPUT to open the INPUT SOURCE list.
6 Press
S
or T to highlight HDMI1 or HDMI2, then press ENTER.
Game console
HDMI cable
22
Note
An HDMI cable carries both audio and video. You do not need to use any
audio cables.
www.insigniaproducts.com
AV (good)
22" 1080p 60Hz LED TV
Notes
Cables are often color-coded to match color-coded jacks.
On your TV
AV cab le
connector
AV jackAnalog
1 Make sure that your TV’s power cord is unplugged and the game console is turned off.
2 Connect the video and audio connectors on the game console’s AV cable (not provided) to the VIDEO jack and L and
R AUDIO jacks on the back of your TV and to the composite jack(s) on the game console.
Audio cable
connectors
audio jacks
Back of TV
Console-specific
AV cab le
Important
• Some older game consoles come with a special AV cable. See the
documentation that came with your game console or check the
manufacturer’s website.
• When you connect the audio using the L and R AUDIO jacks, the audio
output is analog.
Game console
3 Plug your TV’s power cord into a power outlet, then turn on your TV.
4 Turn on the game console, then set it to the correct output mode. For more information, see the documentation that
came with the console.
5 Press INPUT to open the INPUT SOURCE list.
S
6 Press
or T to highlight AV, then press ENTER.
www.insigniaproducts.com
23
Loading...
+ 53 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.