Ingersoll-Rand 65142X-XX User Manual

OPERATOR’S MANUAL 65142X-XX

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

MATERIAL FILTER

MAXIMUM INLET PRESSURE 6,000 P.S.I. (414 Bar)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

THIS MANUAL COVERS THE FOLLOWING MODELS:

CARBON STEEL 300 STAINLESS STEEL CARTRIDGE MESH SIZE

651422-3T 94597-3T None

651422-30 94597-30 30
651420-40 651422-40 93944-40 40
651420-70 651422-70 93944-70
651420-100 651422-100 93944-100 100

SERVICE KITS

Use only genuine ARO replacement parts to assure compatible

y

pressure rating and longest service life.
Refer to  gure 3 to order replacement parts.

y

93944-200 200

70

RELEASED: 11-10-92
REVISED: 12-11-07
(REV. H)

MATERIAL FILTER DATA

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . see Model Description Chart

for “-XXX” (optional screen)

Material . . . . . . . . . . . . . . . . . . . . . . . . . . . see Model Description Chart

Maximum Fluid Pressure . . . . . . . . . 6,000 p.s.i.g. (414 bar)

OPERATING AND SAFETY PRECAUTIONS

Read and heed all warnings, cautions and safety precau-

y

tions before operating this pump.

WARNING

injury or property damage. Do not service or clean pump,
hoses or dispensing valve while the system is pressurized.

CAUTION

been trained for safe working practices, understand it’s
limitations, and wear safety goggles / equipment when re­quired.

WARNING

as stated on the air motor model plate. Operating pump at
higher pressure may cause pump damage.

WARNING

jury or property damage. Do not attempt to return a pump
to the factory or service center that contains hazardous
material. Safe handling practices must comply with local
and national laws and safety code requirements. Obtain
Material Safety Data Sheets on all materials from the sup­plier for proper handling instructions.

HAZARDOUS PRESSURE. Can result in serious

Be certain all operators of this equipment have

Do not exceed the maximum inlet air pressure

HAZARDOUS MATERIALS. Can cause serious in-

Figure 1

GENERAL DESCRIPTION

The ARO model 65142X-XX material  lter is used to separate for­eign materials, like dirt, stones and sweeping compound, from
the material handling section. Material  lters and strainers can be
installed in a system to combat this problem, thereby achieving
longer service life. Filters and strainers are normally located in one
of two places in the pumping system. At this point, where the  uid
enters the material handling section, the strainer prevents foreign
material from entering the system.

INGERSOLL RAND COMPANY LTD

P.O. BOX 151 y ONE ARO CENTER y BRYAN, OHIO 43506-0151

[phone] y FAX [phone]



© 2007 CCN 99445959

DISASSEMBLY

Unscrew and remove (1) cap from the (7) body.

1.
Remove (2) gasket from (1) cap.

2.
Remove (3) spring and (4) button guide from the (7) body.

3.
Pull the (6) cartridge and (5) ball from the (7) body.

4.

TYPICAL SYSTEM VIEW

Install the material  lter either at the inlet of material handling

1.
section or upstream from the other accessories (control handle,
etc.).
Refer to typical installation ( gure 2).

2.
The  lter unit was tested at the factory with a maximum work-

3.
ing pressure of 6,000 p.s.i. (414 bar).

.

Two (8) pipe plugs are included with this unit to plug the inlet

4

and outlet ports not being used.

These system components are shown for installation purposes only

c

and must be purchased separately.

Main air supply



4-1/4" Pump

F-R-L



Filter

1



2

3

4

5

6

7





Material

Outlet Hose

Mounting
Bracket

Material
Inlet
Hose

Figure 2

PARTS LIST / 65142X-XX

Item Description

Cap

1

2 Gasket (1) 91447 [D]

3 Spring (1) 90408 [SS]

4 Guide Button (1) 93949 [SS]

Ball

5

6 Cartridge

Body

7

Pipe Plug

8

(size)

(651420-XX)

(651422-XX)

(13/16” o.d.) (651420-XX)

(651422-3T)

(651422-30, -40, -70, -100

(see table, page 1)

(651420-XX)

(651422-XX)

(1/2 - 14 N.P.T.) (651420-XX)

(651422-XX)

(Qty) Part No. [Mtl]

(1) 92990-1 [C]

(1) 92990-2 [SS]

(1) Y16-126 [SH]

- - - - - - - - - - -

(1) 90815 [SS]

(1) - - - - - [SS]

(1) 92992-1 [C]

(1) 92992-2 [SS]

(2) Y17-13-C [C]

(2) Y17-13-S [SS]







Tighten to 30 - 40 ft lbs (40.7 - 54.2 Nm).



Apply Wet Sol “Plus” to threads at assembly.



Apply Loctite® 572™ to threads.

8



Figure 3

MATERIAL CODE

[C] = Carbon Steel
[D] = Acetal
[SH] = Hard Stainless Steel
[SS] = Stainless Steel

Page 2 of 2 65142X-XX (en)

ARO® is a registered trademark of Ingersoll-Rand Company

y

Loctite® is a registered trademark of Henkel Loctite Corporation

y

572™ is a trademark of Henkel Loctite Corporation

y

y

Figure 4

y

y

PN 97999-6