Ingersoll-Rand 651418-100-B, 651418-40-B, 651418-70-B User Manual

OPERATOR’S MANUAL 651418-XX-B
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
MATERIAL FILTER
MAXIMUM INLET PRESSURE 6,000 P.S.I. (414 Bar)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
THIS MANUAL COVERS THE FOLLOWING MODELS:
MODEL MATERIAL TYPE SCREEN MESH SIZE (optional) 651418-40-B Carbon Steel 93945-40 - 40 mesh 651418-70-B Carbon Steel 651418-100-B Carbon Steel 93945-100 - 100 mesh

SERVICE KITS

Use only genuine ARO replacement parts to assure compatible
y
pressure rating and longest service life. Refer to  gure 3 to order replacement parts.
y

MATERIAL FILTER DATA

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . see Model Description Chart
for “-XXX” (optional screen)
Material . . . . . . . . . . . . . . . . . . . . . . . . . . . see Model Description Chart
Maximum Fluid Pressure . . . . . . . . . 6,000 p.s.i.g. (414 bar)
93945-70 - 70 mesh
RELEASED: 1-17-79 REVISED: 12-10-07 (REV. E)

OPERATING AND SAFETY PRECAUTIONS

Read and heed all warnings, cautions and safety precau-
y
tions before operating this pump.
WARNING
injury or property damage. Do not service or clean pump, hoses or dispensing valve while the system is pressurized.
CAUTION
been trained for safe working practices, understand it’s limitations, and wear safety goggles / equipment when re­quired.
WARNING
as stated on the air motor model plate. Operating pump at higher pressure may cause pump damage.
WARNING
jury or property damage. Do not attempt to return a pump to the factory or service center that contains hazardous material. Safe handling practices must comply with local and national laws and safety code requirements. Obtain Material Safety Data Sheets on all materials from the sup­plier for proper handling instructions.
HAZARDOUS PRESSURE. Can result in serious
Be certain all operators of this equipment have
Do not exceed the maximum inlet air pressure
HAZARDOUS MATERIALS. Can cause serious in-

GENERAL DESCRIPTION

The ARO model 651418-XX-B material filter is used to separate foreign materials, like dirt, stones and sweeping compound, from the material handling section. Material  lters and strainers can be installed in a system to combat this problem, thereby achieving longer service life. Filters and strainers are normally located in one of two places in the pumping system. At this point, where the  uid enters the material handling section, the strainer prevents foreign material from entering the system.
Figure 1

DISASSEMBLY

Unscrew and remove (1) cap from the (8)  lter body.
1. Remove (2) gasket from (1) cap.
2. Remove (3) spring and (4) button guide from the (8)  lter body.
3. Pull the (6) cartridge and (5) ball from the (8)  lter body.
4. Unscrew the (8) filter body from the (7) body and remove (2)
5. gasket.
Replace worn seal and parts with new parts. Reverse disassembly instructions for assembly.
INGERSOLL RAND COMPANY LTD
P.O. BOX 151 y ONE ARO CENTER y BRYAN, OHIO 43506-0151
(800) 276-4658 y FAX (800) 266-7016

TYPICAL SYSTEM VIEW

Install the material  lter either at the inlet of material handling
1. section or upstream from the other accessories (control handle, etc.). Refer to typical installation ( gure 2).
2. The  lter unit was tested at the factory with a maximum work-
3. ing pressure of 6,000 p.s.i. (414 bar).
.
One Y17-15-C pipe plug is included with this unit to plug the
4
inlet port not being used. Two Y17-12-C pipe plugs are includ­ed with this unit to plug the outlet ports not being used.
These system components are shown for installation purposes only
c
and must be purchased separately.
1
2
3
4
5
Main air supply
4-1/4" Pump
F-R-L
Filter
Material
Outlet Hose
Mounting Bracket
Material Inlet Hose
Figure 2
PARTS LIST / 651418-XX-B
(13/16” o.d.)
(see table, page 1)
(3/8 - 18 N.P.T.)
(1 - 11-1/2 N.P.T.)
(size)
MATERIAL CODE
[C] = Carbon Steel [D] = Acetal [SH] = Hard Stainless Steel [SS] = Stainless Steel
(Qty) Part No. [Mtl]
(1) Y16-126 [SH]
(1) 93945-XXX [SS]
(2) Y17-12-C [C]
(1) Y17-15-C [C]
Item Description
1 Cap (1) 92990-1 [C]
2 Gasket (2) 91447 [D]
3 Spring (1) 90408 [SS]
4 Guide Button (1) 93949 [SS]
5 Ball
6 Cartridge
7 Body (1) 92412-1 [C]
8 Filter Body (1) 92993 [C]
9 Pipe Plug
10 Pipe Plug
6
8
2
7
9
10
2
 Apply Loctite® 277™ to threads.
Tighten to 30 - 40 ft lbs (40.7 - 54.2 N m).
3
Figure 3
ARO® is a registered trademark of Ingersoll-Rand Company
y
Loctite® is a registered trademark of Henkel Loctite Corporation
y
277™ is a trademark of Henkel Loctite Corporation
y
y
y
y
PN 97999-8
Page 2 of 2 651418-XX-B (en)
Loading...