INGENICO IPP2XXCL, IPP2XX User Manual

IPP200 Series INSTALLATION GUIDE

Safety instructions:

Lithium battery: IPP200 Series device is equipped with a lithium battery non-accessible to the user. Only a qualified operator is authorized to open the unit and replace this component.

VORSICHT: IPP2 ist mit einer Lithium-Batterie, die nicht zugänglich ist für den Benutzer ausgestattet. Der Wiedereinbau der Batterien muß von qualifiziertem Personal bewirkt werden. Beachten Sie die Polarität für die Batterie Lithium. Eine fehlerhafte Installation der Batterie kann eine Explosion führen. Entsorgen Sie die Batterien entsprechend den Anweisungen des Herstellers.

CAUTION: For Switzerland, Annex 4.10 of SR 814.013 applies for batteries

Power supply network: To cut off the IPP200 Series power, disconnect the power adapter from the power supply network. You should provide a socket for the incoming power supply satisfying the following conditions:

 Socket near the device and easy to access;  Socket in line with the standards and regulations in force in the country of use;

The protection in the installation must be 20A for pluggable equipment type A.

FCC standard compliance marking certifies that the product stipulated below: IPP2X0-01TXXXXX conforms to the following harmonized standards : – part 15 subpart B of the FCC rules This class (B) digital apparatus complies with Canadian ICES-003.

FCC: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help

CAUTION: The user is cautioned that any changes or modifications not approved by INGENICO could void user’s authority to operate the equipment

IPP200 Series INSTALLATION GUIDE

RSS-Gen Clause 7.1.2 statement

"Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication."

"Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante."

RSS-Gen Clause 7.1.3 statement

"This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device."

"Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement."

+ 2 hidden pages