INFOCUS LP850, LP860 User Manual [ru]

LP

®

840/LP®850/LP®860 INSTALLATION &INTEGRATION PROJECTOR.

USER’S GUIDE

WARNING: The power cord and cables associated with this product contain lead, a chemical known to the state of
California to cause birth defects or other reproductive harm. Wash hands after handling.

WARNING: This product has a lamp which contains a very small amount of mercury. Dispose of it as required by
local, state, or federal ordinances and regulations. For more infor mation, see www.eiae.org

qЬбл=ЙенбкЙ=млЙкЫл=ЦмбЗЙ=бл=~о~бд~ДдЙ=зе=нЬЙ=ЙеЕдзлЙЗ=`a=~л=~е=^ЗзДЙ=^ЕкзД~н=йЗС=СбдЙ=бе=нЬЙ=СзддзпбеЦ=д~еЦм~ЦЙлW=aмнЕЬI=bеЦдблЬI=cкЙеЕЬI=dЙкг~еI=fн~дб~еI=kзкпЙЦб~еI=
mзкнмЦмЙлЙI=pй~еблЬI=oмллб~еI=g~й~еЙлЙI=hзкЙ~еI=qк~Збнбзе~д=`ЬбеЙлЙI=pбгйдбСбЙЗ=`ЬбеЙлЙK=_ЙСзкЙ=млбеЦ=нЬбл=йкзаЙЕнзкI=йдЙ~лЙ=кЙ~З=нЬЙлЙ=белнкмЕнбзелK=

aЙтЙ=Ь~еЗдЙбЗбеЦ=бл=бе=тбае=ЦЙЬЙЙд=ДЙлЕЬбвД~~к=зй=ЗЙ=ДбаЦЙозЙЦЗЙ=ЕЗ=бе=ЗЙ=озкг=о~е=ЙЙе=йЗСJДЙлн~еЗ=E^ЗзДЙ=^ЕкзД~нFI=Йе=пЙд=бе=ЗЙ=оздЦЙеЗЙ=н~дЙеW=bеЦЙдлI=cк~елI=
aмбнлI=fн~дб~~елI=kззклI=mзкнмЦЙЙлI=pй~~елI=kЙЗЙкд~еЗлI=oмллблЕЬI=g~й~елI=hзкЙ~~елI=нк~ЗбнбзеЙЙд=`ЬбеЙЙлI=оЙкЙЙеозмЗбЦЗ=`ЬбеЙЙлK=iЙЙл=зеЗЙклн~~еЗЙ=белнкмЕнбЙл=
оззкЗ~н=м=ЗЙтЙ=йкзаЙЕнзк=ЦЙДкмбвнK

iЙ=гзЗЙ=ЗDЙгйдзб=ЕзгйдЙн=Йлн=ЗблйзебДдЙ=лмк=дЙ=`a=азбен=лзмл=СзкгЙ=ЗЙ=СбЕЬбЙк=йЗС=ЗD^ЗзДЙ=^ЕкзД~н=З~ел=дЙл=д~еЦмЙл=лмбо~енЙл=W=Ьздд~еЗ~блI=~еЦд~блI=Ск~е´~блI=
~ддЙг~еЗI=бн~дбЙеI=езко¨ЦбЙеI=йзкнмЦ~блI=Йлй~ЦездI=кмллЙI=а~йзе~блI=Езк¨ЙеI=ЕЬбезбл=нк~ЗбнбзееЙдI=ЕЬбезбл=лбгйдбСб¨K=^о~ен=ЗDмнбдблЙк=ЕЙ=йкзаЙЕнЙмкI=оЙмбддЙт=дбкЙ=
ЕЙл=белнкмЕнбзелK=

aбЙ=озддлн®еЗбЦЙ=_ЙемнтЙк~едЙбнмеЦ=блн=~мС=ЗЙк=бг=iбЙСЙкмгС~еЦ=ЙенЬ~днЙеЙе=`a=~дл=^ЗзДЙ=^ЕкзД~н=macJa~нЙб=бе=ЗЙе=СздЦЙеЗЙе=pйк~ЕЬЙе=оЙкСΩЦД~кW=kбЙЗЙкд®еЗблЕЬI=
bеЦдблЕЬI=cк~ет∏лблЕЬI=aЙмнлЕЬI=fн~дбЙеблЕЬI=kзкпЙЦблЕЬI=mзкнмЦбЙлблЕЬI=pй~еблЕЬI=oмллблЕЬI=g~й~еблЕЬI=hзкЙ~еблЕЬI=qк~ЗбнбзеЙддЙл=`ЬбеЙлблЕЬ=меЗ=sЙкЙбеС~ЕЬнЙл=`ЬбеЙJ
лблЕЬK=_бннЙ=дЙлЙе=pбЙ=ЗбЙлЙ=^епЙблмеЦЙе=озк=ЗЙк=sЙкпЙеЗмеЦ=ЗЙл=mкзаЙвнзклK=

i~=йкЙлЙенЙ=ЦмбЗ~=≠=ЗблйзебДбдЙ=лмд=`a=~ддЙЦ~нзI=ЕзгЙ=СбдЙ=^ЗзДЙ=^ЕкзД~н=йЗСI=еЙддЙ=лЙЦмЙенб=дбеЦмЙW=зд~еЗЙлЙI=беЦдЙлЙI=Ск~еЕЙлЙI=нЙЗЙлЕзI=бн~дб~езI=езкоЙЦЙлЙI=
йзкнзЦЬЙлЙI=лй~ЦездзI=кмллзI=Цб~ййзеЙлЙI=ЕзкЙ~езI=ЕбеЙлЙ=нк~Збтбзе~дЙ=Й=ЕбеЙлЙ=лЙгйдбСбЕ~нзK=mкбг~=Зб=мл~кЙ=имЙлнз=йкзбЙннзкЙI=дЙЦЦЙкЙ=дЙ=лЙЦмЙенб=блнкмтбзебK=

eЙдЙ=ЗЙееЙ=ДкмвЙкЬ™еЗДзвЙе=СбееЙл=й™=ЗЙе=оЙЗд~ЦнЙ=`aJЙе=лзг=Йе=^ЗзДЙ=^ЕкзД~н=йЗСJСбд=й™=С›дЦЙеЗЙ=лйк™вW=kЙЗЙкд~еЗлвI=ЙеЦЙдлвI=Ск~елвI=нулвI=бн~дбЙелвI=езклвI=
йзкнмЦблблвI=лй~елвI=кмллблвI=а~й~елвI=взкЙ~елвI=нк~ЗблазеЙдд=зЦ=СзкЙевдЙн=вбеЙлблвK=iЙл=Зблл=~еоблебеЦЙеЙ=С›к=йкзаЙвнзкЙе=н~л=б=ДкмвK=

bлнЙ=Цмб~=Зз=млм•кбз=ЕзгйдЙнз=Йлн•=Зблйзе∞оЙд=ез=`a=~еЙсзI=Езгз=мг=~кимбоз=йЗС=Зз=^ЗзДЙ=^ЕкзД~н=езл=лЙЦмбенЙл=бЗбзг~лW=Ьзд~еЗЖлI=беЦдЖлI=Ск~еЕЖлI=~дЙг©зI=
бн~дб~езI=езкмЙЦмЖлI=йзкнмЦмЖлI=Йлй~еЬздI=кмллзI=а~йзеЖлI=ЕзкЙ~езI=ЕЬбеЖл=нк~ЗбЕбзе~дI=ЕЬбеЖл=лбгйдбСбЕ~ЗзK=^енЙл=ЗЙ=мнбдбт~к=ЙлнЙ=йкзаЙнзкI=дЙб~=Йлн~л=белнкм´πЙлK=

bлнЙ=г~ем~д=ЗЙ=млз=Йлн•=ЗблйзебДдЙ=Йе=лм=нзн~дбЗ~З=Йе=Йд=`a=беЕдмбЗзI=Езгз=~кЕЬбоз=йЗС=ЗЙ=^ЗзДЙ=^ЕкзД~нI=Йе=дзл=лбЦмбЙенЙл=бЗбзг~лW=Ьзд~еЗ¨лI=беЦд¨лI=Ск~еЕЙлI=
~дЙг•еI=бн~дб~езI=езкмЙЦзI=йзкнмЦмЖлI=Йлй~¥здI=кмлзI=а~йзе¨лI=ЕзкЙ~езI=ЕЬбез=нк~ЗбЕбзе~дI=ЕЬбез=лбгйдбСбЕ~ЗзK=^енЙл=ЗЙ=мл~к=Йд=йкзуЙЕнзкI=дЙ~=Йлн~л=белнкмЕЕбзеЙлK

Данное руководство пользователя в полном объеме представлено на прилагаемом компакт-диске в виде pdf-файла Adobe Acrobat на следующих языках:
английском, голландском, французском, немецком, итальянском, норвежском, португальском, испанском, русском, японском, корейском, традиционном и
упрощенном китайском. Перед использованием проектора, прочитайте данные инструкции.

このユーザーズ=ガイドは、プロジェクタに付属している `a に ^ÇçÄÉ=^ÅêçÄ~í の mac ファイル形式として収録されています。次の言語のユーザーズ=ガイドをご利用いただ
けます。オランダ語、英語、フランス語、ドイツ語、イタリア語、ノルウェー語、ポルトガル語、スペイン語、ロシア語、日本語、韓国語、簡体中国語、繁体中国語。この

プロジェクタを使用する前に、ユーザーズ=ガイドを必ずお読みください。

동봉된 CD 에는 Adobe Acrobat PDF 파일 형식의 사용 설명서가 : 네델란드어 , 영어 , 프랑스어 , 독일어 , 이탈리아어 , 노르웨이어 , 포르투갈어 , 스페인어 , 러시아어 ,
일본어 , 한국어 , 중국어 ( 번체 및 간체 ) 로 제공됩니다 . 프로젝터를 사용하기 전에 다음 지침을 읽으십시오 .

附带的 CD 上有 Adobe Acrobat pdf 格式的整本 《使用者指南》，包括下列各种语言版本：荷兰文、英文、法文、德文、意大利文、挪威文、葡萄牙文、西班牙文、俄文、日文、
韩文、繁体中文、简体中文。请在使用投影仪之前先阅读这些说明。

所附的光碟片上，有 Adobe Acrobat (PDF) 格式的這本 《使用者手冊》；所提供的不同語言版本包括：荷蘭文、英文、法文、德文、意大利文、挪威文、葡萄牙文、西班牙文、
俄文、日文、韓文、繁體中文，以及簡體中文。開始使用本投影機之前，請先詳細閱讀這些說明。

Declaration of Conformity

Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon
97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conform to the following
directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
October, 2003

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or
registered trademarks of Adobe Systems Incorporated. InFocus, ProjectorManager,
ProjectorNet, and LP are trademarks or registered trademarks of InFocus
Corporation.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.

EN 55022 Warning

This is a Class A product. In a domestic environment it may cause radio interference,
in which case the user may be required to take adequate measures. The typical use is
in a conference room, meeting room or auditorium.

Canada

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Agency Approvals

UL, CUL, NOM, IRAM, GOST, C-tick

Other specific Country Approvals may apply, see please product certification label.

Remote Control Warning

Laser radiation class II product; wavelength 650nm; maximum output 1mW. Remote
control complies with applicable requirements of 21 CFR 1040.10 and 1040.11. Remote
control complies with applicable requirements of EN 60 825-1: 1994 +A11.

Do not look into laser beam emitted from the front of the remote control

Location of laser beam warning labels on remote

InFocus reserves the right to alter product offerings and specifications at any time
without notice.

2

Ta b l e o f C o n t e n ts

Introduction 5
Positioning the projector 7
Connecting a computer 8

Required computer connections 8
Displaying a computer image 10

First-time projector use with Windows 98 11
Adjusting the image 13
Connecting a video device 14
Displaying a video image 16
Shutting down the projector 18
Troubleshooting your setup 18
Using the keypad buttons 26
Using the remote control 27
Using the audio 28
Optimizing computer images 29
Presentation features 29
Optimizing video images 30
Customizing the projector 30
Using the menus 31

Picture menu 32

Settings menu 35
Maintenance 39

Cleaning the lens 39

Changing the lens 39

Replacing the projection lamp 40

Cleaning the dust filter 42

Using the security lock 42
Appendix 43

Projected image size 43

LED Behavior 44

RS-232 commands 45

If you are experienced in setting up presentation systems, use the included
Quick Set Up card. For complete details on connecting and operating the
projector, refer to this User’s Guide. Electronic versions of this User’s Guide
in multiple languages are available on the included CD and on our website.

The website also has technical specifications (an interactive image size cal­culator, laptop activation commands, connector pin outs, a glossary, the
product data sheet), a web store to buy accessories, and a page for online
registration. See the inside of the back cover for a list of all relevant web
addresses.

3

Important Operating Considerations for Safety

• Place the projector in a horizontal position no greater than 15 degrees

off axis.

• Locate the projector in a well-ventilated area without any obstructions

to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.

• Locate the projector at least 4' (1.2 m) away from any heating or cooling

vents.

• Use only InFocus-approved ceiling mounts.

• Use only the power cord provided. A surge-protected power strip is

recommended.

• Refer to this manual for proper startup and shutdown procedures.

• In the unlikely event of the lamp rupturing, discard any edible items

placed in the surrounding area and thoroughly clean the area along all
sides of the projector. Wash hands after cleaning the area and handling
the ruptured lamp. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or
federal ordinances and regulations. For more information see
www.eiae.org.

Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty section at
the end of this User's Guide.

2 ft (.6m)

2 ft (.6m)

Do not place objects in the areas along the left, back and front sides of the projector

For ceiling mount applications, this area should be 5 feet (1.5m).

2 ft (.6m)

5 ft (1.5m)

4

Introduction

Projector components and features: front

Your new multimedia projector provides three computer, three video, and
two audio inputs, one audio output, and RS-232 control. The LP840 and
LP850 have XGA 1024x768 resolution while the LP860 has SXGA+
1400x1050 resolution. Optional user-changeable short, fixed short, long and
super long throw lenses make this a flexible product suitable for many dif­ferent uses. The projector is easy to connect, easy to use, and easy to main­tain.

Product specifications

To read the latest specifications on your multimedia projector, be sure to
visit our website. Web address information is located on the back inside
cover of this User’s Guide.

Accessories

The standard accessories that came with your projector can be found on the
packing list that came with your projector. Optional accessories are listed in
the Accessories catalog that came with the projector and can also found on
our website. See the inside back cover for the web address.

Online Registration

Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside back cover for
the web address.

heat vent

speakers

elevator foot release

lens

Projector components and features: back

keypad

air intake
vent

remote
control
receiver (IR)

elevator foot release

handle

5

air intake
vent

air intake
vent

back
foot

connectors

Connector Panel

The projector provides three computer and three video connection options:

• one M1-D (DVI with USB)

• one VESA computer

• one BNC (RGBHV and Pr, Pb, Y)

• one component RCA video (Pr, Pb, Y)

• one S-video

• one composite RCA video

VESA computer

M1-D computer

monitor

component video

RS232
serial control

RJ-45

wired
remote

remote
control
receiver
(IR)

lock

The projector provides computer and video connectors for audio support:

• two composite RCA stereo audio (L, R)

• one audio out

• two audio ins for computer

The projector also provides the following connectors:

• one wired remote

• one monitor out

• RS-232 serial connector (for serial control)

• RJ-45 connector (for networked control via ProjectorNet software)

The RS-232 Command Line Interface (CLI) specifications and commands
are available on our website. See the back inside cover of this User’s Guide
for website information.

computer
audio

BNC

external
speakers
(audio out)

composite
video

s-video

power
connector

power switch

6

Positioning the projector

To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guide­lines:

• Position the projector on a flat surface at a right angle to the screen. The

projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.

• Position the projector within 10 feet (3m) of your power source and

within 6 feet (1.8m) of your video device (unless you purchase exten­sion cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.

• If you are installing the projector on the ceiling, refer to the installation

guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 35. We recom­mends using an authorized ceiling mount. The Ceiling Mount Kit is
sold separately; see the Accessories catalog that came with this projec­tor or visit our website for more information.

• Position the projector the desired distance from the screen. The distance

from the lens of the projector to the screen, the zoom setting, and the
video format determine the size of the projected image. For information
about image sizes at different distances, see “Projected image size” on
page 43.

• For the standard lens that comes with the projector, the image exits at a

given angle. However, the lens shift feature makes the image offset
variable. The image offset is 100% at a 10:0 ratio when the projector is in
4:3 mode (default mode). This means that if you have an image 10’
high, all 10’ will appear above the center of the lens.

• The image offset is 50% when the lens shift is at a 1:1 ratio. This means

that if you have an image 10’ high, the bottom of the image will be 5’
below the center of the lens.

• For information about the optional lenses image offsets, see “Projected

image size” on page 43.

10 ft high
image

10:0
bottom of image
100% above lens
center

1:0

bottom of image
50% below lens
center

Projection angle in 4:3 mode (default)

10:0

1:1

lens center

7

Connecting a computer

Required computer connections

Connect one end of the VESA computer cable to the Computer 2 connector
on the projector. Connect the other end to the video port on your computer.
If you are using a desktop computer, you first need to disconnect the moni­tor cable from the computer’s video port.

Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.

NOTE: Always use the power cable that shipped with the projector.

Optional computer connections

To control your computer’s mouse using the projector’s remote control, con­nect the USB and DVI cables to the USB and DVI ports on your computer,
and connect the other end to the Computer 1 (M1-D) connector on the pro­jector. USB drivers must be installed to use the USB feature. For more infor­mation, see page 12.

If your projector cannot receive the remote’s signal due to IR interference,
you can connect directly to the projector via a remote cable. To do so, plug
the remote cable into the wired remote connector on the projector. Plug the
other end into the connector on the remote,

connect computer cable

connect power cable

connect M1-D cable

connect wired remote

To have sound with your presentation, connect the audio cable to your com­puter and to the corresponding computer Audio In connector on the projec­tor.

connect audio cable

8

If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, plug the monitor cable
to the Monitor out connector on the projector.

You can also connect to your computer using a BNC cable. Connect the BNC
connectors on the BNC cable to the appropriate Computer 3 connectors on
the projector. Connect the other end to the video port on your computer. If
you are using a desktop computer, you first need to disconnect the monitor
cable from the computer’s video port. When all 5 BNCs are connected, the
projector handles separate synchs on H and V.

connect monitor cable

connect BNC cables

RG B

H

V

You can control the projector from an LCD control panel, touch screen, or
other control device or computer by connecting an RS-232 cable to the pro­jector’s Serial connector. Specific RS-232 commands can be found in the Ser-
vice and Support section of our website and in this User’s Guide’s
Appendix.

The projector can be managed by ProjectorNet networking software
through its Network (RJ-45) connector. Contact an authorized dealer or
visit our website for information on ProjectorNet.

connect RS-232 cable

connect CAT-5 cable

Network

9

Displaying a computer image

Remove the lens cap.

remove lens cap

Press the power switch on the back of the projector to the on position, then
press the Powe r button on the top of the projector or the remote.

The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness.

? No startup screen? Get help on page 19.

Turn on your computer.

The computer’s image should appear on the projection screen. If it doesn’t,
press the Computer button on the projector’s keypad.

Make sure your laptop’s external video port is active.

Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F5 is used to
turn the external display on and off. Refer to your computer’s documenta­tion to learn your computer’s key combination.

? No computer image? Try pressing the Auto Image
button on the keypad. Get help on page 19.

press Power switch press Power button

I

O

turn on computer

activate laptop’s external port

2

1

10

First-time projector use with Windows 98

The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wiz­ard to load the correct driver (which was installed with your Windows
operating system).

If you are running Windows 2000, Windows ME, or Window XP, skip these
steps and go to “Adjusting the image” on page 13.

a

a Click Next to begin searching for the driver.

b Make sure “Search for the best driver” is selected, then click Next.

c Uncheck any checked boxes, then click Next. Windows automatically

locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.

d When Windows finds the driver, you are ready to install it. Click Next.

b

c

d

11

Skip this page if you did not connect a USB mouse cable

For Windows 98:

• If you connected the USB cable, the Add New Hardware Wizard
appears again. Drivers must be installed to use the USB functionality.

• The Wizard launches two times.

The first time it detects a USB Human Interface Device (for the key­board).

The second time it detects a USB Human Interface Device (for the
mouse).

For Windows 2000, Windows ME, and Windows XP:

• The USB drivers are automatically installed.

12

Adjusting the image

Adjust the height of the projector, if necessary, by pressing the release but­tons on each side of the projector’s front to extend the elevator feet.

adjust height

release
button

elevator
foot

release
button

elevator
foot

Position the projector the desired distance from the screen at a 90 degree
angle (perpendicular) to the screen.

See page 43 for a table listing screen sizes and distances.

Adjust the zoom or focus by pressing the power Zoom or power Focus
buttons on the keypad until the desired image size and focus are produced.

You can also adjust the zoom and focus via the menus. See page 32

If the image is not on the screen or viewing area, adjust it by pressing the
lens shift button on the keypad.

Press the upper Lens Shift button to shift the lens upward. Press the lower
Lens Shift button to shift the lens downward.

You can also adjust the lens shift via the menus. See page 32.

Adjust the Contrast or Brightness in the Picture menu.

See page 31 for help with the menus.

adjust distance

adjust zoom and focus

zoom focus

adjust lens shift

lens shift

adjust Contrast or Brightness

contrast

brightness

13

Connecting a video device

Standard video connections

Plug the audio/video (A/V) cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the yel­low Video 3 connector on the projector. Plug a white connector into the left
audio out connector on the video device and plug a red connector into the
right audio out connector on the video device. Plug the remaining white
connector into the left audio in connector on the projector, and plug the red
connector into the right audio in connector on the projector.

Connect the black power cable to the connector on the back of the projector
and to your electrical outlet. NOTE: Always use the power cable that
shipped with the projector.

Optional video connections

If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
device and into the Video 2 connector on the projector. Use the A/V cable’s
audio connectors as described directly above (the yellow connectors on the
A/V cable are not used).

If the video device uses component cable connectors (sold separately), plug
the cable’s green connectors into the green component-out connector on the
video device and into the Video 1 green component connector (labeled “Y”)
on the projector. Plug the component cable’s blue connectors into the blue
component-out connector on the video device and into the blue component
connector (labeled “Pb”) on the projector. Plug the component cable’s red
connectors into the red component-out connector on the video device and
into the red component connector (labeled “Pr”) on the projector. Use the
A/V cable’s audio connectors as described above (the yellow connectors on
the A/V cable are not used). NOTE: The component connectors can be used
for HDTV sources (480i, 480p, 720p and 1080i formats).

connect A/V cable

connect power cable

connect S-video and video cables

connect component cables
and video cables

14

You can also connect to your video device using a BNC cable. Connect the
BNC connectors of the BNC cable to the appropriate Computer 3 connec­tors on the projector. Connect the other end to the video port on your video
device. Use the A/V cable’s audio connectors as described on the previous
page (the yellow connectors on the A/V cable are not used).

When 4 BNCs are connected, the projector handles a composite synch on H.
When 3 BNCs are connected, the projector handles a composite synch on G.

NOTE: The BNC connectors can be used for HDTV sources (480i, 480p,
720p and 1080i formats).

connect BNC cables

RG B

H

V

15

Displaying a video image

Remove the lens cap.

remove lens cap

Press the power switch on the back of the projector to the on position, then
press the Powe r button on the top of the projector.

The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness.

? No startup screen? Get help on page 19.

Plug in and turn on the video device.

The video device’s image should appear on the projection screen. If it
doesn’t, press the Video button on the keypad.

Adjust the height of the projector, if necessary, by pressing the release but­tons on each side of the projector’s front to extend the elevator feet.

Position the projector the desired distance from the screen at a 90 degree
angle to the screen. See page 43 for a table listing screen sizes and distances
to the screen.

press Power switch press Power button

I

O

turn on video device

adjust height

adjust distance

release

button

elevator
foot

2

1

release

button

elevator
foot

16