InFocus LNS-W01, LNS-W01Z, LNS-T01, LNS-T01Z, LNS-T02 Replacement Instructions Manual

...

- 1 -

LCD PROJECTOR

LENS REPLACEMENT AND INSTALLATION PROCEDURES

CAUTION

When installing or replacing the Projection Lens, refer to this manual. For installation of the lens, use the parts designated in the manual. Do not use the installation manual and Light-Block Sheets in the lens package. Check the following parts supplied to this projector.

NOTES ON LENS INSTALLATION

●

Lens installation and replacement should be made by the qualified service personnel.

●

Be sure to install the lens following this procedure precisely.

●

Do not touch or remove any parts except the lens and related parts. It may result in malfunctions, electrical shock, fire hazard or other accidents.

●

Before installing or replacing the lens, check that the Model No. of the Projection Lens matches to the projector.

●

When moving or setting up the projector, be sure to replace the Lens Cover to protect the surface. And be careful not to hold or subject the lens to strong forces. It may damage the lens, cabinet, or mechanical parts.

●

For details of the lens and installation, contact the sales dealer where you purchased the projector.

● LIGHT-BLOCK SHEETS 3 pcs.

● LENS MOUNTING ADAPTERS 2 pcs.

● ADAPTER SCREWS 8 pcs.

1AA6P1P2922-- (MV6A) a

This projector applies the Projection Lenses listed below. Use the suitable lens for where the projector is used.

✳ For installing those lenses, attaching Lens Mounting Adapters or removing Guide Pins is

required. Make sure the Model No. of the lens and the installation procedure on next pages and be sure to install the lens precisely.

Model NO.

LNS-W01✳ LNS-W01Z LNS-T01✳ LNS-T01Z LNS-T02 LNS-W02✳ LNS-W02Z

LNS-M01✳ LNS-M01Z

LNS-S01✳ LNS-S02✳

LNS-S02Z

Type

Fixed Short Throw Lens

Fixed Long Throw Lens

Long Throw Zoom Lens

Short Throw Zoom Lens I

Semi-Long Throw

Zoom Lens

Standard Zoom Lens II

Standard Zoom Lens I

Zoom

Motor Driven

Fixed Manual

Focus

Fixed

Motor Driven

Manual

Motor Driven

AVAILABLE LENS

LNS-W03

LNS-S03

Short Throw Zoom Lens II

Standard Zoom Lens III

Fixed

Manual

Motor Driven

- 2 -

NOTE : The installation procedure and needed parts for lens installation depend on the type of the Projection Lens. Check the Model No. of the Projection Lens and be sure to install or replace the lens following procedure below.

Remove Lower Lens Cover. Remove 2 Screws A. Push part B and pull Lower Lens Cover down.

(See Fig. 1.)

Remove 4 Screws C. Pull Upper Lens Cover toward front and remove. (See Fig. 2.)

Remove 2 Screws D and Cover Plate on the back of Upper Lens Cover. (See Fig. 3.)

LENS REPLACEMENT AND INSTALLATION PROCEDURE

Fig-3

Fig-1

Fig-2

UPPER LENS COVER

COVER PLATE

UPPER LENS COVER

LOWER LENS COVER

Connect Lens Motor Lead to the connector "K96T" on the circuit board under the lens. (The model with Lens Motor only.) Fix Lens Motor Lead with the wire holder on the circuit board.

For installing the lenses listed below, attaching Lens Mounting Adapters is required. Before mounting the lens, attach Lens Mounting Adapters. Refer to "LENS MOUNTING ADAPTER INSTALLATION."

Model No.: LNS-W02, LNS-S01, LNS-M01

For installing the lenses listed below, removing Guide Pins is required. Before mounting the lens, remove 2 Guide Pins from Lens Mounting Bracket. (See Fig. 4.)

Model No.: LNS-W01, LNS-S02, LNS-T01

Replace Lens Cap on the rear (mounting side) of Projection Lens and mount the lens on Lens Mounting Bracket with 4 Screws. When installing the model with Lens Motor, be sure to mount the lens with Lens Motor on the right. (See Fig. 4.)

GUIDE PIN

LENS LOCK SCREW

Fig-4

DRIVER IN THE LENS

LOCATE MOTOR ON RIGHT SIDE

LENS MOUNTING BRACKET

- 3 -

Fig-5

K96T CONNECTOR

LENS MOTOR LEAD

Part No. (610 275 6029)

+ 5 hidden pages