InFocus IN112x, IN116x, IN118HDxc, IN119HDx, IN119HDxc User Manual

...

Declaration of Conformity

Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 97223-8368 USA

We declare under our sole responsibility that this projector conforms to the following directives and norms:

ErP Directive 2009/125/EC

EMC Directive 2004/108/EC

EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3

Low Voltage Directive 2006/95/EC

Safety: IEC 60950-1:2005 (2nd Edition) + A1: 2009 and EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP®, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

NOTE: This product is covered electrical and electronic equipment under the

European Union's Waste from Electrical and Electronic Equipment ("WEEE") Directive (2002/96/EC). The WEEE Directive requires that covered equipment be collected and managed separately from typical household waste in all EU member states. Please follow the guidance of your local environmental authority or ask the shop where you purchased the product for collection or recycling options.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.

Canada

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals

cMETus

Other specific Country Approvals may apply. Please see product certification label.

This document applies to regulatory models IN112x, IN114x, IN116x, IN118HDx, IN118HDxc, IN119HDx, IN119HDxc.

Input ratings: 100-240Vac, 2.6A, 50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

Table of Contents

Introduction 4 Positioning the projector 6 Connecting a computer source 8

VGA connection 8 Connecting power 8

Optional computer connections 8 Displaying an image 9 Adjusting the image 10 Connecting a video device 11

Video device connections 11

HDMI connection 11

Composite video connection 11

VGA connection 11

Component video connection 11

S-video connection 11

Audio 11 Shutting down the projector 12 Troubleshooting your setup 12 Using the remote control 20 Using the audio 21 Using the keypad buttons 22 Optimizing computer images 23 Presentation features 23 Optimizing video images 24 Customizing the projector 24 Using the menus

Basic Menu 26

Advanced Menu 27 Maintenance 31

Cleaning the lens 31

Using the security lock 31

Replacing the projection lamp 32

Important Operating Considerations for Safety

’ /1.5m

’

/2.4m

3’ / 1 m

• Refer to this guide for proper startup and shutdown procedures.

• Follow all warnings and cautions in this manual and on the projector.

• Place the projector in a horizontal position no

• Locate the projector at least 4' (1.2m) away from

• Do not block ventilation openings. Locate the projector in a well-ventilated

area without obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.

• Do not place the projector in direct sunlight, humid, greasy or dusty places or

in places where the projector may come into contact with smoke or steam.

• Do not touch or block the projector lens with any objects

the projector lens. Scratches, gouges and other lens damage are not covered by the product warranty.

• Do not look directly into the lens while

• Do not drop the projector.

• Do not spill liquid on the projector. Spilled

• Use the power cord provided. Connect the power cord to a receptacle with a

protective safety (earth) ground terminal. A surge-protected power strip is recommended.

• Do not overload wall outlets.

• When disconnecting the power cord,

hold the plug, not the cord.

• Wash hands after handling the cables supplied with this produ

• The projector remote control uses batteries. Make sure the batteries’ polarity

(+/-) is aligned correctly. Dispose of used batteries in accordance with local disposal laws.

• Use an InFocus approved ceiling mount kit for proper fitting, ventilation and

installation. The warranty does not cover any damage caused by use of nonapproved ceiling mount kits or by installing in an improper location.

• When the projector is ceiling mounted, wear protective eyewear to prevent eye

injury before opening lamp door.

• Refer all service to qualified service personnel.

can be dangerous to you and will void the warranty.

greater than 15 degrees off axis.

any heating or cooling vents.

as this can damage

the projector is being used.

liquid may damage the projector.

ct.

Servicing your own projector

• Only use replacement parts specified by InFocus.

Unauthorized substitutions

may result in fire, electrical shock, or injury, and may void the warranty

• Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty.

• Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.

• The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.

• In the unlikely event of a lamp rupture, particles

may exit through the projector vents. Please keep people, food, and drinks at least 3’ (1m) away from all projector vents. For ceiling applications, keep people, food and drinks out of the "keep out" area under and around the projector, as indicated by the illustration.

Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty Booklet.

Introduction

connector panel

power cord connector

focus

lens

remote control receiver (IR)

zoom

keypad

security bar

lamp cover

lens

remote control receiver (IR)

zoom

keypad

security bar

lamp cover

Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. The IN112x has native SVGA 800 x 600 resolution, the IN114x has native XGA 1024 x 768 resolution, the IN116x has native WXGA 1280 x 800 resolution, and the IN118HDx/IN118HDxc/IN119HDx/IN119HDxc have native 1080p 1920 x 1080 resolution. They are compatible with a wide variety of computers and video devices.

Product specifications

To read the latest specifications on your multimedia projector, be sure to visit our website at www.infocus.com, as specifications are subject to change.

Accessories

The standard accessories that came with your projector are listed in the included Quick Start Guide. Optional accessories can be found on our website at

www.infocus.com/support or at your retailer or dealer.

Online registration

Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.

IN112x/IN114x/IN116x

IN118HDx/IN118HDxc/IN119HDx/IN119HDxc

Connector panel

RS232

computer

composite video

audio in/out

security lock

S-video

monitor

out

HDMI

USB

RS232

computer

audio in/out

security lock

HDMI

USB

The projector provides both computer and video connection options.

IN112x/IN114x/IN116x/IN118HDx/IN119HDx:

• VGA computer (2)

• Composite video

• HDMI

•S-video

• USB connector for firmware upgrades, mouse control and Screen Save

• Monitor out, for VGA pass through to an external monitor.

• Audio inputs for video and computer.

• Audio output to external speakers.

• RS-232 serial control. Comman

d control codes are on our support website at

www.infocus.com/support.

IN118HDxc/IN119HDxc:

• VGA computer (1)

• HDMI

• USB connector for firmware upgrades, mouse control and Screen Save mode.

• Audio inputs for video and computer.

• Audio output to external speakers.

• RS-232 serial control. Comman

d control codes are on our support website at

www.infocus.com/support.

mode.

IN112x/IN114x/IN116x/IN118HDx/IN119HDx

IN118HDxc/IN119HDxc

Positioning the projector

60 inches high image

bottom of image 9 inches above center of lens

Projection angle

lens center

To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:

• Position the projector on a flat surface at a right angle to the screen. The projector must be at least 39.4” (1.0m) from the projection screen.

• If you are installing the projector on the ceiling, we strongly recommend using InFocus approved ceiling mounts for proper fitting, ventilation and installation. Refer to the installation guide that comes with the InFocus Ceiling Mount Kit (p/n PRJ-MNT-UNIV) for more information. The warranty does not cover any damage caused by use of non-approved ceiling mount kits or by installing in an improper location. To turn the image upside down, see “Ceiling mount” on page 28. We recommend using an InFocus authorized ceiling mount.

• Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen and the video format determine the size of the projected image.

Table 1: IN112x (SVGA)/IN114x(XGA) Screen size

Diagonal Screen Size (inches/m)

40”/1.0m 32”/0.8m 61”/1.6m 67”/1.7m 60”/1.5m 48”/1.2m 91”/2.3m 100”/2.6m 80”/2.0m 64”/1.6m 122”/3.1m 134”/3.4m 100”/2.5m 80”/2.0m 152”/3.9m 167”/4.3m 150”/3.8m 120”/3.1m 228”/5.8m 251”/6.4m

Diagonal Screen Size (inches/m)

40”/1.0m 38”/1.0m 58”/1.5m 69”/1.8m 60”/1.5m 58”/1.5m 87”/2.2m 104”/2.6m 80”/2.0m 77”/2.0m 115”/2.9m 138”/3.5m 100”/2.5m 96”/2.4m 144”/3.7m 173”/4.4m 150”/3.8m 144”/3.7m 216”/5.5m 260”/6.6m

Throw Ratio = 1.9 to 2.09

Size of the Projected Image Width (inches/m)

Table 2: IN116x (WXGA) Screen size

Throw Ratio = 1.5 to 1.8

Size of the Projected Image Width (inches/m)

Distance to screen

Minimum distance (inches/m)

Distance to screen

Minimum distance (inches/m)

Maximum distance (inches/m)

Minimum Distance to

Screen Offset Offset for 60in. Image

39.4"/1.0m 15%+-5% 9"/22.9cm

Table 3: IN118HDx/IN119HDx (1080p) Screen size

Diagonal Screen Size (inches/m)

40”/1.0m 43”/1.1m 49”/1.3m 64”/1.6m 60”/1.5m 64”/1.6m 74”/1.9m 96”/2.4m 80”/2.0m 85”/2.2m 98”/2.5m 128”/3.3m 100”/2.5m 107”/2.7m 123”/3.1m 160”/4.1m 150”/3.8m 160”/4.1m 184”/4.7m 240”/6.1m

Throw Ratio = 1.15 to 1.5

Size of the Projected Image Width (inches/m)

Distance to screen

Minimum distance (inches/m)

Maximum distance (inches/m)

Table 4: IN118HDxc/IN119HDxc (1080p) Screen size

Throw Ratio = 1.4 to 1.7

Diagonal Screen Size (inches/m)

40”/1.0m 43”/1.1m 60”/1.5m 73”/1.9m 60”/1.5m 64”/1.6m 90"/2.3m 109”/2.8m 80”/2.0m 85”/2.2m 120”/3.0m 145”/3.7m 100”/2.5m 107”/2.7m 150”/3.8m 182”/4.6m 150”/3.8m 160”/4.1m 224”/5.7m 272”/6.9m

Size of the Projected Image Width (inches/m)

Distance to screen

Minimum distance (inches/m)

Maximum distance (inches/m)

Connecting a computer source

connect VGA cable

connect HDMI

connect power

connect audio cable

VGA connection

Connect one end of the provided computer cable to th Computer 1/Computer 2 connector on the projector and the other to the VGA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first.

HDMI connection

HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video-out connector on the video device and into the HDMI connector on the projector.

Connecting power

Connect the black power cord to the Power connector on the rear of the projector and to your electrical outlet. If the Power Saving Mode feature is off, the Power LED on the Status Indicator Panel (page 12) blinks green. If the Power Saving Mode feature is on, the Power LED is steady amber You can change the setting, see page 29. NOTE: shipped with the projector.

Optional computer connections

To get sound from the projector, connect an audio cable (optional cable, not included) to your computer and to th Audio 1/Audio 2 connector on the projector. You may also need an adapter.

. By default, this feature is off.

Always use the power cord that

If you are using a desktop computer and want to see the image on your computer scr

een as well as on the projection screen, connect to the desktop’s computer cable to Computer 1 and the desktop’s monitor cable to the Monitor Out connector on the projector.

NOTE:

Not available on the IN118HDxc or IN119HDxc.

Displaying an image

press Power button

turn on computer or video device

activate laptop’s external port

monitor key or LCD/CRT key

FN key

Press the Power button.

The Power LED blinks green, and the start up screen displays and the Power LED turns solid green. It can take up to a minute for the image to achieve full brightness. Note: When the feature, AC Power On, is enabled, the projector automatically turns on when power is connected. This allows control of ceiling mounted projectors with a wall power switch.

the fans start to run. When the lamp comes on,

No start up screen? Get help

on page 13.

Turn on your computer or video device.

The image should appear on the projection screen. If it doesn’t, press the Source button on the projector’s keypad or remote.

If you are using a VGA cable to connec

If using a laptop, make sure its external video

Many laptops do not automatica

lly turn on their external video port when a

t your computer to the projector:

port is active.

projector is connected. Usually a key combination like FN + F8 or CRT/LCD key turns the external display on and off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol. Press FN and the labeled function key simultaneously.

Refer to your laptop's documentation for more information about your lap

top's key combination.

No laptop image? Try pressing the Auto Image button on the remote. Get

help on page 13.

Adjusting the image

adjust height

elevator foot

adjust distance

adjust zoom and focus

adjust keystone adjust Basic Menu

If necessary, adjust the height of the projector by rotating the elevator foot to extend the foot.

If necessary, rotate the leveling foot located at the rear of the projector.

Avoid placing your hands near

Position the projector the desired distance

the hot exhaust vent at the front of the projector.

from the screen at a 90 degree angle to

the screen.

See page 6 for a table listing scree

n sizes and distances.

Adjust the zoom or focus.

If the image is not square, first make sure tha

t the projector is perpendicular to the

screen. If the image is larger or smaller on the top or bottom edge of the screen, press the top Keystone button to

reduce the upper part of the image, and press

the bottom Keystone button to reduce the lower part.

If the left or right side of the screen is lar

ger or smaller the other, you can turn the

projector to the left or to the right a few degrees to square the image.

Adjust the Contrast or Brightness in the these menu adjustments.

Basic Menu. See page 26 for help with

+ 25 hidden pages