Infinity RS-2.5 Owners manual

The Electronic Crossover/Equalizer Unit

The active Crossover/Equalizer control unit,which is part of the Reference Standard 4.5 system and
optional with the RS 2.5, makes it possible for the user to compensate for room acoustics and
speaker placement.

The unit is connected into the signal path between the preamplifier(s) and power amplifier(s). In the
case of a receiver without an externally accessible link between its pre-amp output and its power amp
input, the connections are made through the tape monitor circuit for equalizer use only.

When active bi-amplification of an RS 4.5 or RS 2.5 speaker system is desired, the
Crossover/Equalizer must be used.

Brief Theory of Operation

Each signal channel of the unit consists of a 6-dB-per-octave low- and high-pass filter. Each of these
filters has its own variable cutoff frequency (3 dB down point) and output level controls. The high-pass

portion of the circuit has a high-frequency

MODE switch in the EQ position, the output of the high and low filters is summed electrically. By

the
varying LOW PASS GAIN, LOW PASS and/or HIGH PASS frequency controls, it is possible to
generate a wide variety of frequency response contours in the 2OHz- 1 kHz range. Use of the high­frequency contour control (HF) affects the response in the 2-20 kHz region. The EQ position of the
MODE switch permits frequency response variations in modes 2 and 4 that are essentially like those
possible in mode 5. (See RS 4.5 and 2.5 speaker instruction manuals.)

With the MODE switch in Bi-Channel (BI-CH), the low- and high-pass filter outputs appear at their
respective output jacks and will feed separate low- and high-range power amps as outlined in mode 5.
The effect of the controls is similar to the EQ position, except the "summing" is taking place
acoustically.

Description of Front Panel Controls

A summary of the controls and their functions on the Crossover/Equalizer from left to right on the
front panel listed below:

Figure A. (EQ unit, front)

contour control giving 5 dB of boost or cut at 15 kHz. With

1. LOW PASS Frequency: Sets the - 3dB point of the low-pass filters from 110 to 440 Hz in 1/2-

octave steps.

2. LOW PASS Gain: Adjusts the output level of the low-pass filters. Low-pass output appears at
low-pass output jacks regardless of the position of the MODE switch. With the MODE switch in EQ,
LOW PASS GAIN sets the amount of low-frequency signal in wide-band sum appearing at high-pass
outputs. Absolute gain from input to low-pass outputs is unity (x 1 or 0 dB) with LOW PASS GAIN
control at 0 mark.

3.

HIGH PASS Frequency: Sets the - 3dB point of the high pass filters from 110 to 440 Hz in

1/2-octave intervals.

4.

HIGH PASS Gain: With the MODE switch in Bi-Channel setting (BI-CH), the HIGH PASS

GAIN adjusts the output in the high-pass frequency range independent of the LOW PASS GAIN

settings. When the MODE switch is set to EQ, the HIGH PASS GAIN controls the output level of the
wideband output at the high-pass jacks on the rear panel. In this mode, bass is adjusted relative to mid
and high frequencies with the LOW PASS GAIN. Absolute gain from input to High Pass outputs is
unity in either mode when the HIGH PASS GAIN is set to the 0 mark. This control should be set to
unity (0) for most installations. The Crossover/Equalizer has 6 dB of excess gain with the HIGH PASS
GAIN rotated fully clockwise. This can be put to advantage if the overall system gain is low because of
the use of some lower-gain preamps or power amps (such as the Infinity Hybrid Class A Power Amp).

It is not recommended that the HIGH PASS GAIN be used as an overall system volume control in the

EQ mode and further should not be set at less than unity (0).

5. HF (High Frequency Contour): Adjusts high-frequency response of system in a boost/cut
fashion with a range of ± 5 dB @ 15 kHz.

6. MODE sets the unit for functioning as a low-level active electronic crossover in the BiChannel
(BI-CH) position or as an active equalizer in the EQ position.

7. POWER turns unit power on and off. Power on is indicated by a red LED indicator to the right
of the POWER switch. Power can be switched on or off with system preamp power, switched
independently, or left on continuously.

Figure B (EQ unit back)

BACK PANEL FUNCTIONS

Viewed from rear of panel from left to right:

AC Voltage Selector. Allows the unit to be externally set to operate in different countries. Insert

pointed object, such as a small screwdriver, into depression of switch and set position of switch so that
white line lines up with correct voltage range.

AC line cord: Connect to suitable source of power (50/60 Hz frequency 105-125 V AC).

Fuse: Replace with AGC 1/8A fuse only. If fuse blows, most likely cause is voltage selector switch set

in wrong position.

BYPASS Switch:
Permits the unit to be signal-bypassed in the EQ mode. Normal operation as described herein is with

the BYPASS switch placed at IN. With the BYPASS switch placed at OUT, the input signal will
appear at the High Pass/EQ outputs.

Inputs:

Connect the signal source from the preamp, or preamp outputs of receiver or integrated amplifier, to

these jacks.

HIGH PASS / EQ:

Connect these jacks to system power amplifier inputs in operational modes 2 and 4. Connect them to
system midhigh power amplifier inputs in mode 5. The signals at these jacks are phase inverted in
respect to the inputs with the bypass switch in.

LOWPASS:

Connect these output jacks to system low-frequency power amplifier in mode 5 only. Do not
connect anything to these jacks for any other mode of operations. The signals at these jacks are
phase inverted in respect to the inputs.

Operation of the Crossover/Equalizer

Operation will first be described with the MODE switch in the EQ position, which is relevant to
system operation modes 2 and 4. Connect the Crossover/Equalizer inputs to an appropriate signal source
(pre-amplifier, tape recorder, tuner output) and the outputs to the power amplifier(s).

The low-pass frequency is controlled by the left-hand control. Start by setting the LOW PASS
frequency at 220. The LOW PASS GAIN control (second from left) should be set at unity gain (0).

The HIGH PASS frequency control (third from left) should be set at 220. HIGH PASS GAIN (fourth
from left) should be set at unity gain (0).

The HF contour control (fifth from left) should be set at FLAT, which is straight up, or twelve
o'clock. The MODE switch should be set at EQ. Under these conditions, the gain of the
Crossover/Equalizer is unity and the signal out will be flat. This can be checked by operating the
BYPASS switch on the rear panel, which puts the unit in and out of the circuit.

The easiest way to understand how to use the controls is to think of the LOW PASS GAIN as a bass
control, similar to a tone control on a pre-amp, and the High-frequency contour control (HF) as similar
to a treble control on a pre-amp.

If the flat setting does not satisfy you, try these adjustments.

Play music of various sorts and listen to the effect of these controls. If more bass is desired, rotate the
LOW PASS GAIN clockwise, or if less bass is desired rotate it counter-clockwise. The high frequency
contour control (HF) works the same way; clockwise for more highs, counter-clockwise for less highs.

As long as the two frequency controls are set to the same frequency and the LOW PASS GAIN
control is set to unity gain (0), the low frequency response of the unit will be flat. There are five

frequency sets

When the frequency controls are set to different frequencies, the result is equalization.

For example: If both controls are set at 220 Hz, and the LOW PASS is then moved to a lower
frequency such as 156 Hz, and the HIGH PASS is moved to a higher frequency such as 312 Hz, the
result is a dip in response between 156 and 312 Hz. As the low pass is moved lower and the high pass is
moved higher, the dip in the response becomes deeper.

If a peak in response is needed, the frequency controls should be overlapped. For

example: If more output is desired at 220 Hz, the LOW PASS frequency can be raised to 312 Hz and
the HIGH PASS frequency lowered to 156 Hz. The more the settings are over-lapped, the higher the
peak.

In summary, when you rotate the two frequency knobs toward each other, there is an increase in
output in the range between the two settings. When you rotate the knobs away from each other,
there is a decrease in output in the range between the two settings. These EQ characteristics are
illustrated by Figures C and D. As these figures suggest, a large variety of curve shapes can be
obtained. Further action can be obtained.by adjusting the LOW PASS GAIN control. When the unit
is placed in the Bi-Channel (BI-CH) mode and appropriate connections to amplifiers and speakers
have been made, the effect of the controls is the same as in the EQ mode, with one difference.
In the EQ mode the HIGH PASS GAIN control affects the overall system output, and does not alter
the frequency balance. In the Bi-Channel (BI-CH) mode, the LOW and HIGH PASS GAINS are
independently adjustable. The recommended nominal starting settings for the RS 2.5 or RS 4.5 in bi­channel operation are:

4.5 2.5

Low pass frequency
Low pass gain
High pass frequency

110, 156, 220, 312 and 440 -- that will give a flat frequency response.

220 312

00

220 312

High pass gain
HF contou
Mode

Since the RS crossover/equalizer inverts phase at its outputs, both in the equalizer and bi-channel
modes, it is recommended that each amplifier to speaker cable be phase reversed at one end only so that
red or "hot" at the amp end goes to black at the speaker input terminals. This is done to preserve overall
system absolute phase.

Bi-Ch (Necessary)

Figure C

00
00

Figure D

In Case of Trouble

DO NOT ATTEMPT ANY REPAIRS. Check the fuse and, if necessary, replace it only with a fuse
of the same type. But do not open the Crossover/Equalizer unit; doing so voids the warranty. The unit
is delicate and difficult to service; it is also light and easy to ship. So if the unit seems not to be
functioning properly, ask the dealer from whom you purchased it for instructions.

Infinity strives always to update and improve existing products, as well as to create new ones. So the
specifications and construction details in this Infinity publication and others are subject to change
without notice.

Infinity

We get you back to what it’s all about. Music

1979 by Infinity System, Inc., 7930 Deering Avenue, Canoga Park, California 91304, U.S.A.
[phone]. TWX(910) 494-4919